Search Documents

By David C. Oyler, William P. Diamond

Three long horizontal holes were drilled from a directionally drilled sur¬face hole at the Emerald Mine near Waynesburg, Pa. The purpose was to adapt the technique of directional drilling for use in draining methane from coalbeds. A 504-m (1,652-ft) long, 76-mm (3-in) diam¬eter, circular arc pilot hole was drilled, using a downhole mud motor, to enter the Pittsburgh coalbed at a verti¬cal depth of 305 m (1,000 ft). The hole was reamed to 222 mm (8-3/4 in) and was cased to a measured depth of 486 m (1,595 ft). Three 76-mm (3-in) diameter horizontal drainage holes were then drilled, totaling 2,909 m (9,544 ft) of horizontal hole. Improvements in drilling methods increased the average drilling rate from 20.4 m (67 ft) to 64.9 m (213 ft) per day. The cost of drilling the directional and horizontal holes (using a Government-owned drill rig) was $1,169,530, a figure inflated by inexperience and by delays caused by lost-circulation problems and fishing operations. An estimated total drilling cost of $960,000 (including rental of a drill rig) for an improved system, was determined by a detailed cost analysis. Initial gas and water production from November 1979 through May 1980 was low because of caving of the horizontal holes drilled in shale near the bottom of the casing.

Jan 1, 1982

By Paul J. Barrett

The Bureau of Mines evaluated a sulfurous acid-sulfuric acid process for recovering alumina from clay, in which clay is leached. successively with sulfurous acid and sulfuric acid. The resulting aluminum sulfite and aluminum sulfate solutions are combined and heated to produce a basic aluminum sulfate and sulfur dioxide. Alumina is extracted from the basic aluminum sulfate as sodium aluminate by leaching with dilute sodium hydroxide. After desilication, sulfuric acid is used to precipitate alumina as alumina trihydrate, which is then calcined to alpha-alumina. The estimated fixed capital cost for a plant producing 1,000 tons per day of alumina is about $74 million on a 1971 basis. For comparison with previous alumina-from-clay evaluations, the estimated fixed capital cost for the plant is about $67 million on an M and S Chemical Equipment Index basis of 24.0.0, which is equivalent to a 1960 cost level. Because the operating cost is highly dependent on fuel and electric power costs, graphs are included to show the effect of these items on the operating cost. On a 1971 basis, with natural gas costing 35 cents per million Btu and operating labor costing $4 per hour, the estimated operating cost is about $100 per ton of alumina. On a 1960 basis, with labor costing $2.30 per hour and natural gas costing 25 cents per million Btu, the estimated operating cost is about $86 per ton of alumina.

Jan 1, 1973

By Van E. Shaw

Bastnaesite is a natural rare-earth fluorcarbonate of the cerium group that affords an abundant and high-grade source of the lighter rare-earth elements. A simple and efficient method has been developed by the Bureau of Mines for extracting rare-earth compounds from this mineral. Digesting of a flotation concentrate with sulfuric acid converts the rare-earth compounds from fluorcarbonates to sulfates. Action of the acid releases gaseous com-pounds of fluorine and silicon, leaving the sulfated material free of these elements; carbon dioxide from carbonate decomposition is eliminated at the same time. Calcining the sulfated material at 1,200° F. renders the gangue constituents insoluble, whereas the rare-earth sulfates are left in water-soluble form. Leaching with water yields a solution of pure rare-earth sulfates. Bastnaesite could become prominent as a source of cerium-group rare-earth elements. It is rich in the light rare-earth elements and comparatively easy to process; reserves of the mineral are extensive enough to supply a greatly expanded market for many years.

Jan 1, 1959

By T. A. Kubala

Electric discharge ignition has been reinvestigated in a modified Hartmann apparatus for lycopodium powder with air. Minimum stored energy to ignite air dispersions of lycopodium was 25 to 30 mj; ignition occurred with 1 gram of lycopodium dispersed into the 2.7-liter vessel. Ignition energy was measured as a function of the weight of powder used, although some reservations are expressed concerning the uniformity of the lycopodium-air mixtures. In particular, wall layers of lycopodium, remaining after dispersal of 1 gram of lycopodium, were as easily ignitable as the most easily ignited air dispersion. Thus, an unanswered question has arisen concerning the role of surface coatings in the flammability of all marginally ignitable mixtures.

Jan 1, 1981

By G. E. Rennick, F. E. Armstrong, J. Pasini, J. R. Abrams

An oil well penetrating the Pittsburgh bituminous coalbed in northern West Virginia was plugged and safely mined through 3 months later. A sensitive chemical tracer, introduced into the oil reservoir before the test, was not detected in the mine air following the plugging and during mining of the pillar and penetration of the well. Effectiveness of the plugging in preventing reservoir gas from entering the mine through the well hole was verified by continuous monitoring of the mine air for indications of sulfur hexafluoride, an inert gas detectable in amounts as minute as 112 part per billion. Expand- able cement and fly ash-gel-water slurry were utilized to seal the well above and below the coal seam. Three other wells were also plugged using various techniques.

Jul 1, 1972

By W. H. Ode

Low-temperature distillation tests at 200°, 350°, and 500° C. were made on a subbituminous coal from Boulder County, Colo., and a subbituminous coal from Weld County, Colo., in connection with a survey of carbonizing properties of American coals and investigations of their chemical and physical properties. The coal represented by the sample from Weld County was reported to give off combustible volatile matter at unusually low temperatures When placed on a fuel bed. The yields of tar and oil and the composition of the gas from this coal, as obtained in the distillation tests, did not confirm this report. These yields and the gas composition of the Weld. County coal differed but little from those obtained from the coal from Boulder County. Both coals yielded tar and gas in amounts considered to be normal for coals of their rank.

Jan 1, 1937

By A. J. Kraemer

For a number of years the Bureau of Mines has conducted semi-annual survey to determine the changes in the characteristics of the rotor gasoline being sold in the United States. Certain cities have been decided upon as points of origin of samples. Tare choice of these cities has been governed by their situation as the representative of a more or less definitely bounded marketing territory. Samples have been taken on or about the fifteenth day of January and July of each year. In the collection of the samples an attempt has been made to get a representation of the important types of motor fuel being sold, and also to tame into consideration the proportion of tie total consumption that is supplied by the different marketers. It is therefore felt that the survey affords a reliable indication of the quality of the gasoline being sold throughout the United States at the time of sampling. The figures in Table I, below, were obtained by averaging the end points of the least volatile and most volatile samples of gasoline. For example, of 850 samples analyzed in 1919, the 10 per cent (85 samples) having the highest end points, and the 1C per cent having the lowest end points were averaged. These averages are represented in the table as the "Maximum 10 per cent" and the "Minimum 10 per cent", respectively. The same scheme was used in the succeeding surveys.

Jan 1, 1925

By M. Kanefsky, A. Q. K. Rajput

Two channel polarity coincidence and polarity difference statistics are analyzed. The signal, common to both channels, consists of sinusoidal bursts where the exact frequency of the signal is nearly known, but other parameters such as amplitude, phase, and pulse starting time are unknown. The noise inputs are dependent, narrow band, Markov processes. It is shown that the performance depends not only on the signal uncertainties but on the precise shape of the cross-correlation functions between the noise inputs. By using two polarity difference statistics in addition to the polarity coincidence statistic, it is shown that the decrease in performance, as well as the cost of hard limiting due to correlated inputs, can be made small.

Jan 11, 1981

By C. R. Stephan, N. B. Greninger, J. R. Lipscomb

The U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) are participating jointly in a research program to evaluate the strength characteristics and air-leakage resistance of various proposed seal designs for use in underground coal mines. The full-scale seals were constructed in the USBM's experimental mine at the Lake Lynn Laboratory, air-leakage tested, then subjected to pressure pulses of 20 psig or greater. bjected to pressure pulses of 20 psig or greater. In experiments prior to this study, seven seal designs using solid-concrete blocks were tested. Only the standard-type seal passed the explosion and air-leakage criteria. Tests also were performed on four seals constructed with low-density foam blocks. All four of these seal designs withstood the pressure pulse. In more recent studies, nine cementitious foam seal designs of varying thicknesses and densities were investigated. Six of the nine designs successfully survived the explosion overpressures. Six wood- block convergence seals also have been tested. The typical 3-ft-thick, wood-block seal design currently used in many coal mines did not maintain its integrity, in the absence of convergence forces, following the explosion test. Five modified wood-block seals successfully withstood the 20-psig pressure pulse. Based on these tests, three alternative seal construction materials, cementitious foam, low-density foam block, and wood, have been approved by MSHA for use in underground coal mines.

Jan 1, 1993

By R. V. Subramanian

This project financed by the Bureau of Mines investigated the use of polymers to achieve rock bonding and reinforce coal mine structures for better or permanent ground support. Support was achieved by pumping the polymers into the rock interstices to bond the mass together for increased structural competence. Holes were drilled in the mine roof, after which the polymers were injected at about 100 psi to permeate the cracks. Initial laboratory work indicated that of all the resin systems tested, the epoxy resins could most likely be modified to be suitable for rock injection. This was confirmed when several potentially suitable resin systems underwent intensive evaluation. In a series of three field tests, two conducted in a copper mine with coal mine-type shale and the third in a coal mine, it was shown that the polymers penetrated cracks less than 0.005 inch wide. The fast-setting epoxy systems, cured out in thin films under mine conditions, produced a bond exceeding the strength of the uncracked virgin rock.

Jan 1, 1974

By D. A. Doughty

The Bureau of Mines developed two methods for determining iron II and iron III in 2- to 5-mg samples of coal using electron paramagnetic resonance (EPR) spectrometry. One method used solid coal samples; the other method used aqueous solutions. The method using solid samples was more simple, technically, but required the use of X-ray fluorescent analysis, or another independent method, for determining total iron in the samples, and the results were subject to some uncertainty. The method using aqueous solutions appeared capable of greater certainty and did not require additional methods of total iron analysis but was more involved procedurally. The coals analyzed were found to contain much more iron II than iron III.

Jan 1, 1973

By Dennis R. Dolinar, Lewis A. Martin

Cable bolt technology used by the U.S. coal industry was developed to a large extent in the 1990s. Today, these cable systems include both cable bolts and cable trusses to provide supplemental and secondary support in gate roads. This cable technology is significantly different than the cable systems in use in either U.S. hard-rock mines or Australian coal mines. Development of this technology was initiated and spurred by research efforts of the U.S. Bureau of Mines, and has continued under the health and safety programs of the National Institute for Occupational Safety and Health (NIOSH). It was also followed up by work of roof support manufacturers to create an essentially new support system. In this paper, the important support characteristics of both cable bolts and cable trusses are discussed. The design of cable systems and the basis for that design for tailgate and headgate situations are reviewed and explained. Case histories are presented on the application of these support systems based on experience gained at a number of in situ test sites.

Jan 10, 2000

By d&apos, Kathleen J. Amico

This summary appears in Minerals Yearbook volumes I and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U.S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operations at or near mines.

Jan 1, 1967

By Lester G. Morrel

THE RICH and varied occurrences of metallic ores in Australia, extensive nickel deposits on New Caledonia and phosphate rock on several widely scattered small islands were important aspects of the economy of the South Pacific area. Relatively small quantities of gold and nonmetallic minerals produced in New Zealand, Fiji, and the Territory of Papua-New Guinea remained important to the domestic economies of these islands, but had little importance to overall world mineral supplies. The value of mineral commodities produced in this area in 1964 was estimated at $658 million,3 compared with $585 million in 1963. The year's greatest commodity gains were in bauxite and aluminum, beryl concentrate, manganese ore, nickel smelter products, tin, and coal. Annual increases were recorded in virtually all countries and possessions in the area except Papua-New Guinea, where the drop in output of alluvial gold accounted for a decline of about $160,000. Mineral industry activities in Australia overshadowed those in all other parts of the South Pacific in 1964. Outstanding developments were the sales contract negotiations and physical preparation for exploiting the rich iron ore discoveries in Western Australia, the initiation of domestic crude oil production, the commissioning of two new steal mills and an alumina refinery and a start on the new alumina-aluminum project based on Cape fork bauxite deposits. The principal mineral development in 1864 in New Zealand was the progress on plans of the Newzealand Steel Co. to use indigenous iron sans as the resource base for a local steel industry. In New Caledonia, additions and expansion of the nickel mining and smelting facilities continued throughout the year. Plans for extensive geophysical studies were announced by the Government Geological Departments of British Solomon Islands and Fiji.

Jan 1, 1966

By Edward L. McHugh, Charles Sabine, Louis J. Denes, Jami M. Girard, Peter Metes

The Spokane Research Laboratory, National Institute for Occupational Safety and Health, is investigating various remote sensing technologies as possible tools to detect, monitor, and mitigate hazardous situations in surface mines that could lead to catastrophic slope failure. Promising technologies include a field-portable spectro-polarimetric imager and a stationary interferometric radar device. Field tests were conducted of a prototype visible and near-infrared spectro-polarimetric imager (SPI) built at the Carnegie Mellon Research Institute. The SPI employs anacousto-optical tunable filter (AOTF) to control wavelength, a phase retarder to measure polarization signatures, and a digital camera and computer to capture data. Images obtained at the Mountain Pass and Castle Mountain mines in southeastern California showed that the instrument is capable of obtaining hyperspectral images of highwalls, outcrops, hand samples and drill core in the field. We have retrieved spectra from Mountain Pass images that closely match those of bastnaesite and have had some success in classifying images. Although radio frequency noise in the data limited spectral classification of imagery, we project that careful alignment of the AOTF should minimize the noise and greatly improve classification.

By Ronald D. Hill, Elmore C. Grim

To better appreciate the problems associated with surface mining, it 1s imperative that the stripping operation be understood. Surface mining is a very broad term and refers to any process of removing the earth, rock, and other strata in order to uncover the underlying mineral or fuel deposit. Strip mining is a type of surface mining in which the overburden is removed in narrow bands, one cut at a time. Strip mining methods employed to recover coal can be divided into two general types: area and contour.

Jan 1, 1974

By L. C. IlsLey, E. J. Gleim

The extensive use of pulverized coal for fuel in industrial plants has brought to the front again a question that heretofore has been considered only a mining problem, namely, " Can coal dust be ignited by an electric arc ? " If it can be so imited, the next logical query is , "under what conditions can such ignition occur ? " In view of the new problems relating to pulverized coal installations , and because of occasional mine disasters attributed to ignition of coal dust by electric arcs , it seems advisable to review the work done by Thornton and Bowden with electric flashes in coal dust , and to report two preliminary investigations conducted by the Bureau of Mines .

Jun 1, 1922

By N. S. Dalal, X. Shi

"SUMMARYElectron spin resonance (ESR) measurements provide direct evidence for the involvement of the glutathionyl radical, as well as an isolable Cr(V)-glutathione intermediate in the Cr(VI) glutathione redox reactions. These results indicate a new mechanism for the reduction of Cr(VI) by glutathione in relationship to cellular environment and suggest that synergistic reactions of Cr(V) and GS· might be responsible for the (unexpected) increase in the Cr(VI)-induced DNA-strand breaks at high glutathione levels.INTRODUCTIONWhile the reduction of Cr(VI) by glutathione (GSH) is thought to be a critical' step in the pathogenesis of the Cr(VI)-exposure related carcinogenesis1- 4, the exact reduction mechanism is not yet understood. The following reaction steps have been suggested :(A) Initial step:Cr04 2- + GSH - GSCrOa - (1)(B) At high GSH levels:GSCroa- + GSH - Cr( IV) + GSSG (2)(C) At low GSH levels: GSC rO a - - Cr ( V ) + GS ·(3)Thus far, however, in these reactions, the GS· radical has eluded spectroscopic detection, while the evidence for the Cr(V) formation has been reported positives as well as negative2·. Her~ we present spin-trap ESR evidence for the formation of the GS· radical, and a definitive ESR detection of an isolable cr(V)-GSH intermediate in Cr(VI)-GSH reactions.MATERIALS. AND METHODSESR spectra were obtained at X-band (-9.7 GHz) using a Bruker ER200D ESR spectrometer. The magnetic field was calibrated with a self-tracking NMR Gaussmeter (Bruker, Model ER035M) and the microwave frequency was measured with a Hewlett-Packard (Model 5340A) frequency counter. The spin probes, a-(4-pyridyl-1-oxide) -N -tert-butylnitrone (4-POBN) and 5,5-dimethyl~1-pyrroline-1-ox1de (DMPO) were purchased from Aldrich, K2Cr201 from Fisher and used without further purification. All experiments were done at room temperature."

Jan 1, 1989

By R. M. Ray

The Bureau of Mines evaluated five commercial badge-type carbon monoxide dosimeters. Color changes in the badge reagent indicated the presence of carbon, monoxide. Possible effects of ambient conditions on dosimeter response to CO during or after coal mine fires or explosions were studied. Temperature and humidity changes did not change dosimeter sensitivity to CO. Contaminant gases such as CO2, N02, S02, and H2S had effects that varied with brands of dosimeters ranging from no effect to increased sensitivity to CO. Dosimeters tested after 6 months of storage showed an increase in failure rate as high as 25 percent. Tests were conducted to determine the effects on dosimeter time-for-color change caused by observer's sight (colorblind); lighting, and coal dust on dosimeters. No significant effects were observed. Observer variance was the most pronounced factor observed in all tests.

Jan 1, 1975

By S. R. B. Cooke, F. D. DeVaney

"INTRODUCTION The potash mineral receiving the most attention in the newly discovered. New Mexico-Texas potash district near Carlsbad, N. M. is sylvite (potassium chloride). Sylvite contains more potassium than any other mineral. Merchantable high-grade deposits have been found, and those of lower grade may be enriched to a high degree of purity by refining methods. Deposits containing sylvite were the first to be developed and axe the only ones being mined.However, many other minerals that contain potash occur in the salt beds of the Carlsbad District. Of these the more important are polyhalite, carnallite, langbeinite, leonite, and kainite. The nature of the deposits and their mineralogy have been described in detail by members of the United States Geological Survey. 4/Langbeinite, although not so abundant in these deposits as carnallite and has particular interest because the potash is in the form of the sulphate and as such commands a premium in terms of K20 unit. This is explained by Fox and Turrentine 5/, who state:"

Feb 1, 1936