Search Documents

By Steven J. Schatzel, William P. Diamond

Coalbed gas content measurements are commonly used in mine safety as well as coalbed methane resource assessment and recovery applications. Gas content determination techniques generally fall into two categories: (1) direct methods which actually measure the volume of gas released from a coal sample sealed into a desorption canister and (2) indirect methods based on empirical correlations, or laboratory derived sorption isotherm gas storage capacity data. Direct gas content determination techniques may be further. subdivided into quick-crushing and extended desorption methods. The quick-crushing methods are primarily used in mine safety applications outside the United States, but have also been used for resource recovery applications. Quick-crushing methods rely on crushing the coal sample soon after collection to release all the desorbable gas, thus significantly shortening the amount of time required for desorption measurements. However, some data useful for resource recovery applications are lost. Extended desorption techniques are most commonly used for resource assessment and recovery applications where information on desorption rates is useful for reservoir modeling, and for fundamental coalbed methane research. Extended desorption methods allow the gases in the coal sample to desorb under controlled laboratory conditions until a defined low desorption rate cutoff point is reached. The sample may then be crushed to measure the amount of gas remaining within the sample. Direct method techniques for gas content measurement are the focus of this paper.

By D. L. Boreck

Thick coal seams are common in the Western United States, Many seams are over 50 it thick (some are over 200 ft thick) and are too deep to extract using surface methods. Currently, such deposits are developed using standard "eastern" mining methods which only extract a few feet of total seam thickness, often rendering the remaining coal unminable with current technology. Novel methods that increase thick-seam recovery have been developed and are currently being used in Europe. These methods--high-face single-pass and multislice longwall, longwall caving, and hydraulic mining--have great potential for use in the United States. Successful use of these methods is an objective of the Bureau of Mines. Their use requires, among other things, a full evaluation of geologic features common to thick coals. The objective of this report is to present and summarize those features that will affect the introduction of the methods into thick-seam mines in the Western United States. The geologic elements delineated are three-dimensional configuration of the seam, cleat development, joints and fractures, roof and floor lithology, and faulting.

Jan 1, 1986

By Robert W. Ageton

The Bureau of Mines is currently conducting a comprehensive study to evaluate all aspects of recovering gold from large, low-grade deposits in the Golden Sunlight area, Whitehall mining district, Jefferson County, Mont. Prior to World War II this area produced significant quantities of gold. The study includes geologic mapping, diamond drilling, assaying, computer analysis of assay data, metallurgical research and ore testing, mine and mill planning, and an economic evaluation of all factors bearing on the establishment of a producing gold mine. Preliminary evaluation of the deposit indicates about 31 million tons of submarginal gold resources. American Exploration and Mining Co. (AMEX) has assisted the Bureau in this project by providing drill site preparation, control assays, and geological aid for the Bureau's exploration work and by furnishing comprehensive assay information of the property and copies of base and geologic maps. This report presents the geology and mining history of the area, together with a summary of Bureau work in progress.

Jan 1, 1969

By T. M. Kohler, G. L. Finfinger, D. M. Hyman, A. T. Iannacchione

The Bureau of Mines measured methane emission rates from an advancing salt face ranging from 15 to 56 ft3/ton (0.5 to 1.8 m3/t). Small room size, use of a continuous miner, and a well-defined ventilation system made possible air velocity and methane concentration measurements, These measurements, representing data from 18 production days, were con- ducted in an area of abnormally low grade salt, Methane emissions occurred primarily during the advance of the salt face by continuous miner.

Jan 1, 1982

By Henry Kreisinger, John Blizard

This preliminary statement presents some of the results of tests carried out at the Lakeside Station of the Milwaukee Electric Railway and Light Co. , by the fuel section of the U. S. Bureau of Mines , in cooperation with the research department of the Combustion Engineering Corporation of New York . The object of these tests was to determine the thermal efficiency , ease of operation , and other particulars of a boiler equipped with specially designed furnace and burners for burning powdered coal . The boiler tested haş 13380 square feet of heating surface , and is one of eight boilers equipped with the Lopulco powdered coal system supplying steam to two 20,000 -Kw . steam turbines in the largest power house burning powdered coal . Twenty- six tests were run at rates of heat transference varying from 4000 to 8000 B.t.u. per square foot of boiler heating surface , and the mean thermal efficiency attained was about 84 per cent , based on the gross calorific value of the fuel as fired . The efficiency varied little with the rate of steaming , and its high value is accounted for by the small loss from incomplete combustion and the small amount of excess air which varied from 5 to 36 per cent . The coal burned had a gross calorific value of about 11500 to 12800 B.t.u. per pound , contained 2 to 5 per cent moisture , 33 to 36 per cent volatile matter and 9 to 13 per cent ash, and was so ground thaf 89 to 95 per cent would pass through a 100- mesh sieve . The ash had a softening point of 2150 to 2450 degrees F. , but did not fuse together at the bottom of the furnace because it was partly protected from the flame radiation by means of a series of water tubes connected to the boiler which were placed between the fumace bottom and the flame, ..

Jan 1, 1923

By Phyllip Worley, Frank E. Chase, Christopher Mark

The Harris No. 1 Mine, located in Boone County, WV, has been longwalling the Eagle Coalbed for over 30 years. Harris has experienced numerous interactions associated with the extensive room-and-pillar and longwall mining operations which have been conducted in the overlying No. 2 Gas Coalbed. The problems have included roof falls, excessive rib sloughage, and gateroad and bleeder entry closure. A detailed evaluation of the multiple seam experiences at Harris No. 1 Mine was conducted as part of the National Institute for Occupational Safety and Health (NIOSH) nation-wide multiple seam mining case history data base. One observation from the Harris gateroad case histories was that smaller, critically loaded, upper seam pillars seemed to cause more severe ground conditions than did wider pillars. The LaModel program was used to investigate this supposition, and the results confirmed that “critical” sized pillars do transmit the highest amounts of stress to adjacent seams. In addition, the data suggest that the probability of a major multiple seam mining interaction increases when the depth of cover is 1,000 ft or greater and when the Eagle seam pillars have a Analysis of Longwall Pillar stability factor less than 1.50.

By M. Kanda, W. D. Bensema, J. W. Adams

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in an operating coal mine, Itmann No. 3 Mine, located near Mullens, West Virginia. The electromagnetic environment created by 250-volt-dc and 550- and 950-volt-ac machinery in two longwall panels was measured and is reported. One technique measures noise over the entire electromagnetic spectrum of interest for brief time periods. It is recorded using broadband analog magnetic tape, and the noise data is later transformed to give spectral plots. The other technique records noise amplitudes at several discrete frequencies for a sufficient amount of time to provide amplitude probability distributions. The specific, measured results are given in a number of spectral plots and amplitude probability distribution plots.

Jan 6, 1974

By A. J. Farstad, R. F. Kehrman

Characteristics of metal/non metal mines were evaluated to determine the suitability of applying the U.S. Bureau of Mines electromagnetic location system to the problem of locating trapped driers in metal/non metal mines. Statistical distributions of mine depths and overburden conductivities show that the existing USBM EM system is inadequate for most metal/non metal mines. Alternate approaches to trapped miner location in deep mines were identified and subsequent field tests were conducted at six (6) mines to evaluate their feasibility. The approach considered to be the most promising is one which utilizes the existing manpack transmitting system, modified slightly for a dual frequency output, in conjunction with a sophisticated signal processing receiver on the surface. The main advantage of staying with a "through the earth" approach is that the underground equipment can be kept simple, easily maintained, light- weight and inexpensive.

Jan 1, 1979

By R. K. Koch

The vapor pressures of liquid columbium and liquid hafnium were deter-mined by the Langmuir free evaporation method as a part of the Bureau of Mines program on the study of transition metals. An electron-beam furnace with a water-cooled copper crucible was used for melting. Temperature was measured with a two-color ratio pyrometer. Least-squares analyses of the vapor pres-sure data gave the following equations: [Logp (atm) = 5 .429 -31,310 T] for liquid columbium in the range 2,740° - 3,140° K, and [Log p (atm) = 5,690 28 T] for liquid zirconium in the range 2,500° -2,810° K. Third-law evaluations of each data set gave mean heats of sublimation (298.15° K) of 175.1±3.2 kcal/mole and 148.3±1.2 kcal/mole for columbium and hafnium, respectively. Second-law standard heats of sublimation determined from sigma plots and from sigma-prime plots agreed fairly well with the third-law values. The sigma-prime plots gave standard entropies of sublimation of 30.96±0.84 eu and 33.S6±0.44 eu for columbium and hafnium, respectively.

Jan 1, 1968

By David C. McHuron

The U. S. Bureau of Mines in their continuing research into sealants, selected MBAssociates to design, build, and test equipment and evaluate sealant as to its effectiveness is shale degradation. There were 20,050 sq.ft. of coal mine roof sprayed with a mine sealant and as a result, it has been estimated that the sealant coated roof has from 50% to 95% less roof falls than that roof which was not coated with sealant.

Jan 1, 1980

By W. S. Landers

In contrast to the large fund of information available on the carbonizing properties of Eastern U.S. coals, the experimental data available for most Western U.S. and foreign coals are meager. To supply some self-consistent data, the Bureau of Mines conducted 220 low-temperature carbonization assay tests at 500° C. in a laboratory-scale carbonization apparatus. The results are included in this report. The U.S. coals tested are from Alaska, Arizona, Colorado, Illinois, Montana, New Mexico, North Dakota, Pennsylvania, Ohio, Texas, Utah, and Wyoming. Assays were also made on coals from Canada, Ecuador, France, Greece, India, Mexico, the Philippine Islands, Thailand, and Yugoslavia. In addition, one assay of pine sawdust and one assay of a peat from Ireland are reported. Prediction equations were developed relating the yield of products of carbonization obtained at 500° C. in the assay unit to the proximate and ultimate analyses of the coals. The equations for predicting the yields of tar plus light oil, char, and gas, and the heating value of the gas, are considered good, each equation having a multiple correlation coefficient of 0.90 or higher. The equation predicting volume of gas obtained upon carbonization is considered as fair, with a multiple correlation coefficient of 0.84. A reproducibility study of the assay made on 10 replicate samples of a subbituminous coal indicated that the standard deviation of the individual products was 0.31 percent or less.

Jan 1, 1961

By Paul R. Coyle, Anthony T. Iannacchione

A close look at the Loyalhanna Limestone of southwestern Pennsylvania reveals a complex structural environment. Most exposures of the Loyalhanna occur along Chestnut Ridge and LaurelHill within the Allegheny Mountain Section of the Appalachian Plateaus Province. Because the Loyalhanna is rated as a super-pavement aggregate by the Pennsylvania Department of Transportation and because of its proximity to the population centers of southwestern Pennsylvania, the Loyalhanna has been extensively mined along these prominent anticlinal structures. Geologic and engineering analyses were performed using gas well and core logs, outcrop examinations, underground observations, and mine maps. Strata exposures from both outcrops and quarries were used to construct geologic maps, stereo net, and rose diagram projections so that the Loyalhanna’s structural environment could be understood better. Many of these structural conditions cause ground control problems at local quarries. These problems ranged from small-to-moderate sized rock falls associated with roof jointing to pillar failures associated with dipping discontinuities. Stresses ranged from tensional on structural domes where weathering dominates, to high levels of compression within structural saddles. A greater understanding of these characteristics is a prerequisite to develop engineering controls, such as improved mine layouts, pillar sizes, etc., that lessen miner exposure to these hazards.

By Arthur L. Murray

The first thought in the case of an accident or contagious disease is naturally that aroused by our humane instinct , how serious is the case and will the person recover ? The economic effects of such cases , owing to their many ramifications , are seldom realized either by those directing mining operations or those engaged in the labor of producing . This paper is based on the accident experience of the State of Utah and the number of cases of two well known preventable diseases , typhoid fever and smallpox , in that State for the fiscal years 1917-1918 , 1918-1919 , 1919-1920 , and 1920-1921 . The data and figures presented are from coal -mining camps only . W. W. Adams , mine- accident statistician of the bureau, contributed valuable corrections and suggestions . The economic results of accidents are considered first , and those of the two preventable diseases later .

Apr 1, 1922

By Robert W. Gordon

This report describes the results and conclusions of the further development of a lightweight probe drill for use in anthracite mines. Improvements to the drill previously developed under Contract H0282044 were made and tested at an Eastern Pennsylvania mine. These improvements were: 1. Better hole cleaning due to the development of an air-water mist flushing system. 2. The application of roof drill bits to allow drilling through rock seams and lenses. 3. The development of a quick coupling drill system which reduced total steel change time. 4. Adaptation of a swivel to the drill anchoring system which greatly reduced set-up time between holes. With these improvements the probe drill demonstrated its ability to drill the required 11 holes in one shift. It also gained miner acceptance as a viable underground working tool. The probe drill proved to meet all of the design requirements of portability, low weight drilling controllability, structural integrity and reliability. In addition to its ability to drill the required probe pattern, the probe drill has the capability of drilling long holes. By drilling several holes over 80 feet deep the probe drill has demonstrated a potential for use in robbing pillars and for methane drainage.

Jan 1, 1981

By D. Montagna

The Kroll-Betterton process for debismuthizing lead is based on adding calcium and magnesium to impure molten bullion to form solid Ca-Mg-Bi inter-metallic compounds that float on the surface as drosses. Present practice in industry is to hand-skim off these drosses, often followed by hydraulic pressing to squeeze out some of the entrapped liquid lead. In an effort to develop an improved technique, the use of an argon-shrouded dipping centrifuge to perform the required phase separation was investigated. Centrifugation experiments demonstrated that the bismuth content of an impure bullion could be lowered from an initial 0.5 percent down to 0.03 percent with a lead recovery of 90 percent, which is comparable to lead recovery after hand skimming of drosses in commercial lead-debismuthizing operations. Centrifugation provides better control in removing drosses, faster operation with less oxidation and relatively little fuming, and recovery of a lead bullion that approaches commercial specifications.

Jan 1, 1972

By Fred C. Turin, William J. Wiehagen

This study examined musculoskeletal injury risk at four mining sites: underground coal, underground limestone, surface copper, and surface phosphate. Each site offered opportunities to investigate musculoskeletal disorder (MSD) injury risks and how those risks might be identified and categorized. The National Institute for Occupational Safety and Health (NIOSH) worked with these sites to (1) identify work activities that showed evidence of MSD injury risk, (2) examine physical risk factors that can lead to MSDs for a handful of work tasks at each site, and (3) develop a set of ideas for problem-solving to help reduce risk factors for examined work tasks. For each site, NIOSH implemented a plan that was refined over the time period of this study. The plan consisted of four steps. The first step was to use mine injury records, a musculoskeletal discomfort questionnaire, front-line supervisor interviews, and a list of management concerns to identify work groups and work activities that have significant evidence of MSD risk factors. The second step was to select work tasks for evaluation. The third step was to interview those who do the work and make observations to characterize the MSD risk factors and musculoskeletal symptoms that exist for target tasks. The final step was to conduct brainstorming sessions with workers who perform the work or have a stake in the production task. The brainstorming sessions served to identify general strategies (ideas) for reducing MSD risk factor exposures. A final report of findings was presented to mine management and workforce representatives at each site. The risk factors and ideas for improvement identified for each site were specific to the target tasks examined. These target tasks were diverse, but there were some key similarities. For instance, jobs were found at each site that required a significant amount of manual work involving the upper extremities and low back. Handling heavy and awkward objects, forceful arm and shoulder exertions, and working in awkward postures were common for a variety of jobs across the four sites.

Jan 8, 2004

Reduce costs of recontouring surface mined land by improving bulldozer blades. Approach A specialized 48-foot-wide bulldozer blade set at an angle, a 13-foot bulldozer blade with swept-forward end sections, and a 24-foot grading bar are used in conjunction with conventional bulldozers to reduce the cost of recontouring surface mined land. How They Work The angle blade is used to do the initial and intermediate leveling of long spoil banks. It is mounted at an angle on two 410-horsepower crawler tractors in a side-by-side offset configuration, but requires only one operator since both tractors are controlled by a single set of controls. The angle blade usually begins its cycle at one end of the spoil bank where the operator fills the blade and moves forward, continuously cutting and casting the material to the repose slope. At the opposite end of the spall bank, the angle blade turns around and begins cut-ting and casting material to the opposite repose slope. This action continues until adjacent banks meet or the lateral distance from the center line of the spoil bank to the repose slope exceeds approximately 40 to 50 feet. At this distance, the sidecasting angle blade is no longer effective, and conventional bulldozers are used to do the final land shaping.

Jan 1, 1981

By Manuel Gomez

The mean and the standard deviation were used to describe general sulfur and ash populations as well as specific populations of these variables from one coal seam. Both the mean and the standard deviation were incorporated in the exploration process to determine the number of drill cores necessary for seam evaluation and to guide the sequential drilling plan. Probability regions were computed to establish a basis for predicting probable ranges of average sulfur and ash concentrations that may be expected upon continued or future drilling. A computerized plot program was utilized to interpolate sulfur and ash concentrations between grid points. The plot program, which is essentially a moving average technique, permits a rapid evaluation of sulfur, sulfur forms, and ash spatial distributions as a drilling program progresses sequentially. This information, in the form of contour plots, can be made available to both the mining engineer and the fuel technologist in advance of mining to outline reserves, to improve selective mining, and to anticipate preparation facilities.

Jan 1, 1972

By L. D. Stewart

The main reasons for developing an induction system for signaling from the cage are, first, to increase safety, and second, to effect economies in the operation of cage and ship hoists, especially when work is being done in the shaft. To-day nearly all mines which employ safe methods have installed safety gates on cages, at the different levels, and at the collar of the shaft. Under the old system in some instances signals could only be Given from the station outside the cage, and in other cases, after the signal was given the only method whereby those riding on the cage could control its movements consisted of pulling the bell-rope hanging in the shaft, an uncertain and somewhat hazardous procedure at best. With the system herein described, however, it is possible, without opening the gates, to signal to the engineer from any place in the shaft whether or not the cage is moving, and finder the same conditions it is possible to converse with the engineer by using the telephone. In short, the cage tender has at all times an opportunity either to signal or talk to the engineer without leaving the cage.

Jan 1, 1931

By H. William Zeller

The Bureau of Mines performed laboratory research to determine the effects of a barium-based fuel additive on diesel particulate emissions. The test engine was typical of types used to power underground coal min-ing equipment. Test parameters consisted of baseline measurements without additive, three fuel additive concentrations, and five steady-state engine loads, all at 1,200 r/min. Additive effects on soot mass concen-tration, opacity, particle size distribution, volatile fraction, and NOx emissions were determined. Important findings are as follows: Using the manufacturer's recom-mended additive concentration increased the gravimetrically measured mass of particulate by 30 to 80 pct at four of the five steady-state load conditions. Soot measurements by optical methods did not agree with those by gravimetric techniques, for additive-treated fuels. The additive reduced volatile hydrocarbons adsorbed on filter deposits by up to 50 pet. At most engine loads, carbon particulate was also reduced. About 40 pet of the barium added to the fuel was accounted for in the exhaust. The health implications for miners were considered, but no firm conclusions were drawn or recommendations made because the results are for steady-state conditions, which may not be representative of real-world operation of diesel-powered equipment underground.

Jan 1, 1987