Search Documents

By Walter Kawa

The hydrogenation of phenyl ether, benzyl ether, and phenyl sulfide in the presence of iron catalysts was studied by the Bureau of Mines to gain a better understanding of the role of iron catalysts in the hydrogenation of coal. The carbon-oxygen and carbon-sulfur bonds in these compounds may be similar to some of the carbon-oxygen and carbon-sulfur bonds in coal which react during the early stages of liquefaction by hydrogenation. Experiments were made in batch autoclaves for 4 hours; hydrogen was at a pressure of about 540 atmospheres. In the hydrogenation of phenyl ether at 400° C, metallic iron catalyzed both hydrogenolysis (splitting-hydrogenation) and nuclear hydrogenation (addition of hydrogen to aromatic rings) reactions, Products were principally benzene and cyclohexane. The activity of metallic iron was decreased by adding carbon monoxide or a reactive sulfur-containing organic compound. Ferrous sulfide catalyzed the conversion of phenyl ether to benzene, phenol, and small amounts of cyclohexane. Hydrogenolysis of benzyl ether was catalyzed by metallic iron and to a lesser extent, by ferrous sulfide at 250° C. No nuclear hydrogenation was observed with either catalyst. Conversion of phenyl sulfide to benzene was nearly quantitative in experiments made at 250° C with equimolar quantities of phenyl sulfide and metallic iron or iron as ferric oxide. Conversions of metallic iron and ferric oxide to ferrous sulfide were nearly stoichiometric. No reaction of phenyl sulfide occurred in the presence of ferric oxide and water, and very little occurred in the presence of metallic iron and water. Ferrous sulfide also catalyzed the hydrogenolysis of phenyl sulfide to benzene, but conversion was lower than in experiments with metallic iron or ferric oxide. The activity of ferrous sulfide was increased by adding water and decreased by adding hydrogen sulfide. The results of this study suggest that ferrous sulfide is an active form of iron when iron is used as a catalyst for the hydrogenation of coal.

Jan 1, 1963

By Almon F. Robertson

The floor of Shady Valley, Johnson County, Tenn., is underlain by the Shady dolomite formation. In places the residual clay derived from this formation contains considerable manganese oxides. Nine properties in Shady Valley and two in Doe Valley were prospected by the Bureau of Mines from January 1943 to April 1943. The results obtained indicate that the ore bodies are small and spotty and, that the ore is not well-adapted to gravity concentration. The work of the Bureau was confined to the open end of the valley. One mile northeast of the Ham Greer property, Beaverdam Creek enters a rocky gorge, and it was believed that the few prospects in this area were of secondary impor-tance and, owing to the steep slope and general roughness of the terrain, that exploration with the rite', bucket-drill would be impracticable. A total of 4,398.5 feet was drilled in 131 holes. In addition, 235 lineal feet of bulldozer trenches were cut and 4.5 feet of test pits were sunk. The following nine properties were explored in Shady Valley: Bentley, Walker, Blevins, Scott, North Ham Greer, South Ham Greer, Lipford, Blackburn, and Steagall In Doe Valley, the Gerd Shoun and Brookshire properties were explored.

Jan 1, 1949

By J. M. Gomes

The Bureau of Mines, as part of an effort to maximize minerals and metals recovery from domestic resources, has investigated the feasibility of recovering heavy minerals as byproducts from sand and gravel, placer gold, and industrial mineral operations in northern California. Sand samples from about 50 locations were treated by gravity separation to yield heavy-mineral concentrates (black sands). Mineral compositions of the concentrates were determined by chemical analysis and mineralogical examination. Individual zircon, ilmenite, magnetite, platinum-group metals, thoria, and silica products were prepared from heavy-mineral concentrates by selective separation using low-and high-intensity magnetic, high-tension, and flotation equipment.

Jan 1, 1979

By O. C. Blade

A comparison of certain properties of the commercial aviation gasolines produced in the United States during October 1949, 1950, and 1951 is presented in table 1, the 1951 data being average values from tables 3 through 6 of the present report. Trends in the average values of certain characteristics of these fuels may be seen in figures 1 through 4 which also indicate the minimum and maximum values. As may be observed, with the exception of changes in kinematic viscosities, the properties of commercial aviation gasolines have not varied greatly during recent years. A list of aviation-gasoline survey reports published by the Bureau of Mines is given on page 6. A summary of the average values of the properties on jet fuels is shown in table 2.

Jan 1, 1952

By D. G. Kuehn

Mass spectrographic studies have been conducted on the positive ions and neutral species of glow discharges containing 1.0 pct S02 and 1.0 pct CO in helium. Measurements were conducted for gas pressures from 3.5 to 10.1 torr using both dc and 60-Hz ac excitation. The ion species that were observed included S+, SO+, SO+, 0+, O2+, C+, CO+, and CO2+ with lesser amounts of SO3+, (CO)2+, SCO+, and (SO?CO)+ or CS+2. Interpretation of the functional dependence of the various ionic and neutral species on pressure and applied power showed that CO reacted with the SO formed in the discharges to produce CO2 and sulfur. Deposition of elemental sulfur was observed in the plasma container.

Jan 1, 1973

By R. L. Grayson, T. Simonyi, R. A. Andrel

"The purpose or this paper is to disclose analytical, statistical, and observational results relating to mineralogy and trace elements in respirable dust samples collected from two different mines in West Virginia. Samples were taken from longwall panels, and the panels operated in different coal seams, one located in the northern part or the state and the other in the southern region. Mining conditions and equipment arrangements on the panels will be described along with dust control techniques used. Results from sample analyses are summarized with emphasis on relationships between mineralogy, trace elements and mineral particle size to worker locations. Correlations are made between micro x-ray diffraction and energy dispersive x-ray analyses for sample mineralogy.IntroductionThrough the work of many researchers worldwide, the health of coal miners in modern societies is now protected from harmful exposure to respirable coal mine dust. A vast amount of research culminated in the exposure-response model of Jacobsen, et al, (l) which has been used to establish the 2 mg/m3 exposure limit in the United States. According to the model exposure to respirable dust for 35 years at this level or less could prevent the occurrence of a clinically significant case of coal workers' pneumoconiosis (CWP) in a miner. The exposure limit, of course, must be adjusted whenever greather than five percent free silica exists in the respirable dust.The Jacobsen model was built around a mean mass concentration exposure, which generally showed the highest correlation with both incidence and progression of CWP. As Morgan, et al noted, however, the quantity of respirable dust inhaled is not the only significant factor. 2) They noted that although mass of respirable dust correlates highe.st with the incidence of CWP, it is not a causal factor. Admittedly, the insidious processes causing the disease occur at the lund cell-dust particle level."

Mar 1, 1989

By W. W. Weller

Heat capacities of ferrous molybdate (FeMoO4) and ferrous tungstate (FeWO4) were measured over the temperature range 51° to 298.15° K. Ferrous tungstate has a lambda type heat capacity anomaly at 74° K. The 298.15° K entropies are FeMoO4) 30.9 cal/deg mole and FeW04) 31.5 cal/deg mole.

Jan 1, 1966

By E. O. Wagner, Manuel Gomez, W. S. Landers

The Bureau of Mines studied coking rates of a special Columbia - Geneva six - coal blend to establish the effect of the coking rate on coke properties . The tests were conducted in a 500 - lb , 14 - in experimental slot oven at essentially constant conditions of blend composition , size distribution , surface moisture content , and bulk density . The coking rate was varied as a function of oven flue temperature . Coking rates within the range of 0.56 to 1.35 in/hr were achieved . Increase in the coking rate decreased the size of the coke . The stability factor of the coke showed no significant change with coking rate until coking rates greater than 1.0 in/hr were reached , after which a decrease in the stability factor was observed . The apparent specific gravity increased to a maximum value at coking rates approaching 1.1 in/hr and decreased sharply with further increase in the coking rate . Coke parameters correlated well with the coking rate .

Jan 1, 1963

By J. A. Sutton

In connection with, a stream-pollution-research project, a colorimetric method was developed for concentrations of 1 to 30 p.p.m, of pine oil in water. The method depends on the stable bluish-green color produced when pine oil is reacted with vanillin-hydrochloric acid reagent at 60° C. for 25 minutes. The colorimetric reaction actually determines alphaterpineol, the principal component in pine oil. Some waters may require a special preparation in which ion-exchange resins are used to remove interference. ACKNOWLEDGEMENTS The author wishes to express his appreciation to A. A. Berk, chief of the Industrial Water Branch, Bureau of Mines, for helpful advice and encouragement during the progress of this work and to B. P. Martinez, chief of the Stream Pollution Research Section, for assistance with the manuscript. Thanks are also due to W. D. Bishop of the Hercules Powder Co., Wilmington, Del., for supplying the principal components of pine oil.

Jan 1, 1953

By Barry L. Warner

This program involves testing to determine whether a fire hazard exists when the exposed wood surface area of timber in a mine passageway equals 40 percent of the surrounding strata surface, excluding the sill. Twelve full scale fire tests were conducted in a simulated mine passageways, using kerosene pan fires as the ignition source. The tests included three timber sizes, plus one test with roof lagging, two wood types, plus one test with treated timbers, and two ventilation air velocities. The results show air velocity to be an important factor in the occurrence of flame propagation, and that the 40 percent surface area ratio of wood to surrounding strata appears to b0. a valid criteria for fire safety at 150 fpm, but not at 350 fpm.

Jan 1, 1975

By E. C. Lane

The motor gasoline that is being marketed in the United States this winter is in general, more volatile than that sold a year ago. This increase in volatility is shown by a lowering of the distillation temperatures, ranging from 2°F. at the average initial boiling point to 5°F. at the average end point. During the past eight and. one half years the Bureau of Mines has made semi-annual surveys of the gasoline marketed in the United States, the survey Just completed being the seventeenth in the series. The cities in which samples have been collected, have been chosen as representative of the more important marketing territories, as it is obviously impracticable to obtain a sample of every gasoline sold in the entire country. Samples were collected in Boston for the first time since 1919. It was believed advisable to include samples from that district in order to give a better balance to the survey for the country as a whole.

Jan 1, 1928

By Charles K. Rose

The Cebolla Creek titaniferous iron deposits near Powderhorn in southern Gunnison County, Colo., were examined by the Federal Bureau of Mines as part of an overall program to investigate the Nation's titanium and iron resources. The deposits occur around the periphery of the Iron Hill stock, which underlies an area of about 12 square miles. Concentrations of magnetite, ilmenite, and perovskite arc localized along fractures in the pyroxenite stock. Mineralogical studies of composite surface samples collected in 1956 showed that most of the iron is present in ilmenite-bearing magnetite. Perovskite is the chief titanium mineral in the magnetite-rich and augite-rich types, and sphene is the principal titanium mineral in the placer material. The mica-rich rock contains approximately equal amounts of perovskite, ilmenite, and sphene.

Jan 1, 1960

By Arcy, D&apos Banister

Drilling practices at the Silver Summit mine in Shoshone County, Idaho, and the steps taken to increase drilling efficiency are described for the 1952 to 1958 operating period. Mining and development methods are outlined, and drilling equipment and practice are discussed. Cost and performance data include drilling time, bit duty, steel failure, drill repair, and compressed-air consumption. Steps taken to increase drilling efficiency and decrease costs are described, including modifications of bit design, new procedures for drill-rod fabrication and new processes for completing certain drill-machine repairs.

Jan 1, 1963

By Arcy, D&apos Banister

Drilling practices at the Silver Summit mine in Shoshone County, Idaho, and the steps taken to increase drilling efficiency are described for the 1952 to 1958 operating period. Mining and development methods are outlined, and drilling equipment and practice are discussed, Cost and performance data include drilling time, bit duty, steel failure, drill repair, and compressed-air consumption. Steps taken to increase drilling efficiency and decrease costs are described, including modifications of bit design, new procedures for drill-rod fabrication and new processes for completing certain drill-machine repairs.

Jan 1, 1963

By H. Kenworthy

[Experimental studies were made to develop a laboratory technique for direct removal of cadmium and germanium from sphalerite concentrates. Cadmium- and germanium-bearing concentrates from the Illinois-Kentucky fluorspar field were sound to be, amenable to an inert atmosphere fuming process for removing these two moats in the form of gaseous sulfides. Treating the condensed fume by pyrometallurgical methods upgraded the material end provided a means of partly separating the constituents. Cadmium was concentrated about 35:1 arid germanium about 300:1. The extractive investigations were supplemented by vapor-pressure studies on the sulfides of germanium to obtain fundamental data for larger scale laboratory conditioning and control when treating the zinc concentrates. Vapor-pressure curves were developed for synthesized monosulfide and disulfide The results of these- investigations indicate the possibility of significantly increasing the recovery of cadmium from zinc concentrates. Comparison with present recovery of germanium cannot be made, since commercial recovery data arc not available.]

Jan 1, 1956

By W. E. Young

This study was made to present the mining methods and costs of a uranium mine typical of other mines in the highly productive Westwater Canyon member of the Morrison formation in New Mexico. Four mining methods have been used at the Section 23 mine: the retreat- room-and-pillar method, a sublevel-slicing method (also called top-slicing), the horizontal-cut-and-fill method, and a modification of the ring-drill method. The application of the methods at this mine and at other mines in the area should be of benefit to operators with similar problems. Ore bodies in the Section 23 mine are irregularly shaped and vary in size, in rock strength, in moisture content, and in uranium concentrations; different mining methods are required and mining costs are not constant. A 6-month period of operation at the Section 23 mine was analyzed and mining costs, not including amortization, depreciation, or Federal taxes, averaged about $6.80 per ton.

Jan 1, 1965

By J. M. Mutmansky, L. Xu

"IntroductionSince the establishment of the star,just concentration of 2 mg/m3, a strong effort has made by mining engineers and researchers to provide better dust control equipment and procedures for underground coal mines.Particular areas of success have been implementation of better coal-cutting strategy to control dust generation, better design of water sprays for dust suppression and air movement, use of scrubbers, and improved design of face ventilation systems. A drastic improvement occurred over time such that the average dust concentrations for continuous miner operators dropped from 6.5 mg/m3 in 1968 to 1.3 mg/m3 in 1980 and for auger, cutter, longwall, and roof bolter occupations from 2.7 mg/m3 in 1973 to 1.6 mg/m3 in 1980 (Niewiadomski, 1983).While dust concentrations in mining sections have been dropping considerably, one problem area has been mining sections where quartz is a considerable portion of the airborne dust. The federal regulations require that quartz content must be held below 0.1 mg/m3 in the air regardless of the concentration of the total dust. This legislation limits the allowable dust concentration to a ""reduced standard"" of 10/ (% quartz) when the quartz content of respirable dust in the mine atmosphere is more than 5%. Today, approximately one-third of underground coal mining operations have designated areas with more stringent dust standards in place, and many mines experience considerable difficulty in meeting these standards (Jankowski, and Babbitt, 1989).It is well known that metal miners subjected to respirable dusts high in quartz have a higher incidence of silicosis than those exposed to dust low in quartz. However, the role of quartz in the development of coal workers' pneumoconiosis is still a highly controversial question, in spite of the large number of research projects devoted to this subject over the last 20 years. Because coal seams contain less quartz than metal ores and quartz often comes from sources outside the coal seam (e.g., roof and floor), it is difficult to relate studies that deal with the quartz content in coal seams and the incidence of coal workers' pneumoconiosis. Hamilton, Ogden, and Vincent (1983) have provided a plausible explanation for the incidence of the disease by hypothesizing that the quartz content does not affect the probability of developing pneumoconiosis until some threshold value (generally thought to be about 10%) is exceeded.The objective of the research studies summarized here was to obtain a better understanding of quartz occurrences in airborne coal mine dust by studying the variations of the quartz levels in different dust sizes and the relationship between the quartz content in airborne coal mine dust and the quartz content in the mined material. The implications of the results to control of dust in high-quartz sections will also be discussed."

Mar 1, 1992

By Ronald P. Hollenbeck

Samples of clays, shales, and slates from 29 locations in the Appalachian Region of Alabama and Georgia were tested and evaluated to determine their suitability as raw material for the manufacture of lightweight aggregate by the rotary-kiln method. Samples from 11 locations in Alabama (one each in Etowah, Lawrence, and Morgan Counties and two each in Colbert, Cullman, Tuscaloosa, and Walker Counties) and one location in Walker County; Ga., produced satisfactory lightweight aggregate.

Jan 1, 1969

By W. E. Young

This study was made to present the mining methods and costs of a uranium mine typical of other mines in the highly productive Westwater Canyon member of the Morrison formation in New Mexico. Four mining methods have been used at the Section 23 mine: the retreat-room-and-pillar method, a sublevel-slicing method (also called top-slicing), the horizontal-cut-and-fill method, and a modification of the ring-drill method. The application of the methods at this mine and at other mines in the area should be of benefit to operators with similar problems. Ore bodies in the Section 23 mine are irregularly shaped and vary in size, in rock strength, in moisture content, and in uranium concentrations; different mining methods are required and mining costs are not constant. A 6-month period of operation at the Section 23 mine was analyzed and mining costs, not including amortization, depreciation, or Federal taxes, averaged about $6.80 per ton.

Jan 1, 1965

By R. Hogg, T. F. Dumm

"A procedure for evaluating the size/specific gravity distribution of ultrafine coal and the distributions of sulfur and ash with respect to particle size and specific gravity is described. The procedure is essentially an extension of the conventional coal washability technique in which special precautions are taken to ensure particle dispersion in the heavy organic liquids, centrifuges are used to obtain adequate separation rates, and micromesh sieves are used for size separation at fine sizes. An example of the application of this technique to the evaluation of the extent of liberation of sulfur and ash in a coal sample ground to 90Z passing 200 mesh (74 um) is described.INTRODUCTIONIn order to determine the potential for deep cleaning of coal by fine grinding to liberate sulfur and ash-forming minerals, it is necessary to obtain data on the distributions of these species by size and specific gravity. In conventional coal processing operations, this information is obtained by means of a standard ""washability"" analysis. Attempts to extend this procedure to ultrafine coal, however, have generally been unsatisfactory and have often led to unreliable and inconsistent results [11. The present authors have described a modified washability procedure in which cumulative specific gravity fractionation is combined with sub-sieve size analysis (by laser diffraction/light scattering) to determine the particle size/specific gravity distribution of ultrafine coal [2]. Unfortunately, because this technique does not involve separation of the individual fractions, only limited information can be obtained on the specific distributions of sulfur and ash.The objective of the work described in this paper was to develop and evaluate a procedure for size and specific gravity fractionation of ultrafine coal and to use conventional analyses for sulfur and ash to determine their relative distribution in the coal. The procedure is essentially a simple extension of the standard washability analysis [3] but incorporating special precautions for treating ultrafine particles.EXPERIMENTAL Material The material used in the development and evaluation of the ultrafine coal fractionation procedure was a medium volatile bituminous coal from the Lower Kittanning seam. A sample of the coal (nominally - 1/4 inch), obtained from the Penn State Coal Data Base, was ground to 90% passing 200 mesh by the following two-stage grinding procedure: About 2 kg of the as-received coal were ground to about 30Z passing 200 mesh in a Model 4-E Quakertown mill (""coffee grinder""). About 1 kg of this product was then ground to about 90Z passing 200 mesh in a Holmes Model 300 Pulverizer."

Jan 1, 1989