Search Documents

By J. W. Miller

Depletion of coals most suitable for metallurgical fuel has nude necessary a general survey of coking-coal reserves in the United States. These investigations were begun in 1948 at the joint request of the Munitions Board, Department of Defense, and a number of coal companies. This report, which is one of a series, by counties, describes the preparation characteristics of the coals of Letcher County, Icy. From these data it is possible to determine: (a) Which coals either as mined or after beneficiation by conventional preparation are suitable under present standards for producing metallurgical coke, (b) which coals require special and more intensive treatment in preparation than is now practiced, and, (c) which coals cannot be upgraded by known commercial preparation methods to metallurgical fuel standards now accepted.

Jan 1, 1955

By W. G. Pariseau

The U.S. Bureau of Mines has been conducting a series of rock mechanics investigations at the Lucky Friday Mine in the Coeur d'Alene Mining District of northern Idaho. The present study uses rock deformation measurements to validate and calibrate a geomechanical model of the experimental Lucky Friday underhand longwall (LFUL) stope on the 5,100-ft level of the Lucky Friday Mine, Mullan, ID. The calibrated three-dimensional, finite-element model and measurements of rock mass displacement show a correlation of 0.795. The calibration reduces rock mass modulus to 14 to 17 pet of laboratory values and rock mass strength (with an energy rule) to 37 to 41 pet of laboratory values. This model suggested that stress-related ground control problems would be encountered west of the stope where the vein makes a right-angle turn and then splits. Rock burst activity was concentrated in this area during mining of the LFUL stope.

Jan 1, 2010

By R. D. Govier

The U.S. Bureau of Mines has developed a thin-film X-ray fluorescence technique to rapidly determine Cu, Ni, Co, Fe, and Cr in super alloy leach liquors. Total analysis time per sample was less than 15 min, as opposed to several hours for traditional wet chemical methods. Precision and accuracy were checked by replicate analyses of solutions similar in composition to leach liquors, whose analyte concentrations were well known. Coefficients of variation for all elements were found to be less than 2 pet. With the exception of the results for Fe, all relative errors of estimation were also found to be less than 2 pet. Bulk liquids are not introduced into the spectrometer; thus, the potential for damage to the instrument by leakage of corrosive liquids is eliminated.

Jan 1, 1989

By C. Q. Cupps

n view of increased interest in secondary recovery of oil in the Cut Bank field, Montana, a review has been made of unpublished data obtained during a 1943-44 study of reservoir oil characteristics in this field. Considerable uncertainty was attached to interpretations of subsurface oil sample analyses from six Cut Bank zone wells, one Lander sand well, and one Moulton sand well, because of adverse sampling conditions and wide range in the data. Much of this uncertainty has been removed by this review which has shown two of the Cut Bank zone samples and the Moulton sand sample to be representative of the reservoir oils. Estimates of original reservoir oil characteristics derived from differential-liberation analyses of these samples show that the oil in the Cut Bank zone was initially saturated at the gas-oil contact pres-sure, 750 psia, and the oil in the Moulton sand was undersaturated with a saturation pressure of only 380 psia. The rest of the samples were indicated to be nonrepresentative of the reservoir oils because of a disproportional vaporization of heavier components of the solution gas. The vaporization of these components is believed to be a cumulative effect of contact of the oil with bypassing, light-gravity gas which had been liberated at higher pressures from solution in oil farther back in the formation, or which had come from the gas cap, rather than from the singular effect of gas evolution caused by excessively low bottom-hole pressures. Change of oil composition caused by the latter was found to conform closely to that occurring during a differential liberation of gas in the laboratory.

Jan 1, 1967

By O. C. Blade

This report on the properties of aviation gasolines and aviation jet fuels produced in the United States during 1952 was made under a co-operative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. Analytical data are presented for 94 samples of aviation gasoline which include, for the first time in this series of reports, data on five samples of grade 108/135 aviation fuel. Data also are given for 34 samples of aviation jet fuel. The analyses were made on samples typical of the manufacturers? production in their laboratories and the results submitted to the Bureau of Mines for compilation. The products of 20 manufacturers of aviation gasolines and of 16 producers of aviation jet fuels are represented.

Jan 1, 1953

By D. J. Bauer

This report covers a phase of an extraction project carried out as part of a research program on rare-earth technology. The current project--the production of pure cerium compounds--is an intermediate step between ore processing and metal reduction. In this connection, a study on a separatory-funne1 scale was made on nonreducing extractants for recovering cerium (IV) from tri-n-butyl phosphate (TBP) and of methods for recovering the cerium nitrate from the strip solution. Dilute sulfuric acid was found to be 100 percent effective in stripping cerium (IV). Several precipitants were effective in recovering the cerium from the strip solution, and ethanol was especially promising. A scaled-up investigation was made into the use of spray-tower type equipment to perform the function of extracting, washing, and stripping. This equipment, referred to as the pressure-bubbler, utilized the system developed on the separatory-funnel scale. Feed solutions were prepared from a bastnasite concentrate by two techniques. Of these, the sulfated bastnasite solution was most successful, resulting in 86-percent recovery of the cerium at 99.7+-percent purity.

Jan 1, 1959

By Errol D. Sehnke

This U.S. Bureau of Mines report provides detailed information on worldwide bauxite production capacity by mine and country, including bauxite substitute materials in countries of the former Soviet Union, The information was compiled from a variety of domestic and international sources and was based on information available to the Bureau through December 31, 1994. Capacity data represent announced installed and planned capacities and do not necessarily reflect a U.S. Bureau of Mines judgment of actual mine operating levels or timing of planned expansions. The year-end capacity is the ?in place? capacity or estimated production capacity, whichever is larger.

Jan 1, 1994

By Jon C. Volkwein

The Bureau of Mines conducted a series of tests to evaluate the effectiveness of mixing a compressed-air-generated foam with dried whole-grain silica sand to suppress dust in minerals processing plants. Dust at downstream transfer points was monitored with personal gravimetric samplers and with Real-Time Aerosol Monitors (RAM's) that were connected to strip' chart recorders. Results showed dust reductions of 80 to 90 pct on three separate occasions at two different plants. The mechanism by which foam suppresses dust is discussed, as are the constraints on the use of foam, which may include incompatibility of the foam with the mineral product, difficulty in controlling the foam generator, and cost.

Jan 1, 1983

By W. C. Wahl, M. M. Fine

Leonardite , a naturally occurring , partially oxidized form of lignite with a high content of humic acids , was investigated as a binder for iron ore pellets . Although insoluble in original condition , leonardite forms watersoluble salts with good binding properties when treated with certain alkalis such as sodium hydroxide . Soluble leonardite imparts excellent dry strength to pellets , but green strength is somewhat lower than that obtainable with bentonite . However , green strength can be improved by adding a small amount of calcium hydroxide to the leonardite - concentrate mixture . Leonardite binders were used successfully on three of the four different concentrates tested .

Jan 1, 1964

By L. L. Oden

The purpose of this research was to develop a method to remove copper and tin from the magnetic fraction of incinerated municipal refuse, as recovered by the Bureau of Mines pilot plant in College Park, Md. Copper, present in the scrap in a metallic form bonded to ferrous objects, was amenable to leaching in cupric ammonium carbonate solution. Copper levels in small 5-to 10-lb lots of treated scrap were reduced from the initial level, 0.5 to 0.6 pct, to 0.1 to 0.2 pct. Larger lots of scrap (100 lb) were treated less effectively because of poor contact of solution and scrap. Oxidation in the air or in aerated aqueous solution was applied to liberate tin from the dilute solid solution present on the surface of incinerated tinplate. Shredding of air-oxidized scrap or caustic leaching of scrap oxidized in solution reduced tin levels from the initial 0.25-pct level to about 0.1 pct.

Jan 1, 1973

By J. J. Shields

With the increased use of mechanized equipment in mining bituminous coal, production panels are mined out rapidly. To keep current with the rapid completion of production panels, development work must be speeded up also. Although the same type of equipment usually is employed in development as in production places in the same mine, past output per man for development usually was less than from production panels. A study of development practices in 14 mines reveals a tendency toward equalization of the output per man between development and production.

Jan 1, 1957

By Allen D. Look, Alan A. Sharp

"INTRODUCTION The bottoming of the United Verde sulfide pipe has shortened the expected life of the United Verde mine to a matter of a few years. First located in 1876, this Arizona mine has had a long period of activity, having reached a peak production in 1929 of over 71,000 trans of copper. Through these many years of successful operation, a safety program has evolved in keeping with the proficiency developed in mining the ore body. It is the purpose of this paper to record the safety practices in effect at this mine so that others may have the benefit of lessons ,learned through experience 'and years of work toward an improved accident record.ACKNOWLEDGEMENTSAcknowledgment 'is 'made to ,the Phelps Dodge Corp. for its cooperation in making available data contained in this paper, and to C. E. Mills, general superintendent; W. W. Little, mine superintendent; John Riordan, employment agent; and G. S. Leisk, safety engineer, for their helpful suggestions and information furnished.GENERAL INFORMATIONThe United Verde copper mine is situated just west of Jerome, Ariz., at an altitude of approximately 5,500 feet. Purchased by the Phelps Dodge Corp. in 1935, the mine employs approximately 500 men - 385 underground and 115 on the surface."

May 1, 1949

By John W. Cole

The Butte district has been the principal producer of metallurgical-grade manganese in the United States since World War I. Manganese dioxide nodules are produced from rhodochrosite ore by concentrating the rhodochrosite and roasting the concentrate in rotary "cement-type" kilns. The Anaconda Copper Mining Co. is the only producer at present. Under the stimulus of a purchasing program administered by Metals Reserve Company during World War II, however, several independently owned or operated mines (including the Norwich) produced manganese carbonate ore. These mines were examined in Juno 1949 by John W. Taber, mining engineer, Bureau of Mines. A core-drilling program to develop ore in the Norwich mine was recommended and approved. drilling was completed early in 1950. This report gives factual data obtained.

Jan 1, 1951

The Technical Study Panel on the Utilization of Belt Air and the Composition and Fire Retardant Properties of Belt Materials in Underground Coal Mining (hereafter referred to as the Panel or the TSP) was established by Section 11 of the Mine Improvement and New Emergency Response Act of 2006 (MINER Act). The Panel was charged with providing “independent scientific and engineering review and recommendations with respect to the utilization of belt air and the composition and fire retardant properties of belt materials in underground coal mining.” The TSP was impaneled by the Honorable Elaine L. Chao and commenced its work on January 9, 2007. At this first meeting, Mr. Richard E. Stickler, Assistant Secretary of Labor for Mine Safety and Health, asked the Panel to report on many issues including how recent technological advances could be applied to atmospheric monitoring systems, point-type heat sensors, current state of fire-resistant vs. fireproof belt materials, and belt fire suppression systems to improve miner safety. In addition, Mr. Stickler asked the Panel to review belt air velocity limitations. The Panel members attended 12 days of public meetings over a nine-month period. Three of the public meetings were scheduled for the Panel to hear from technical experts and those persons or organizations interested in providing input. The meetings were held in Coraopolis, Pennsylvania with emphasis on belt fires, belt maintenance, belt flammability and toxicity, ventilation, and escape issues; in Salt Lake City with emphasis on ground control and convergence issues; and in Birmingham with emphasis on fire detection, sensors and atmospheric monitoring systems. National Institute for Occupational Safety and Health (NIOSH) researchers, Mine Safety and Health Administration (MSHA) personnel, representatives of the major belt conveyor manufacturers and a representative of the National Mining Association provided discussions at the Coraopolis meeting. In Salt Lake City, Utah, MSHA district managers and ventilation specialists, a member of the Aracoma Mine No. 1 investigation team, a representative of the Bureau of Land Management, and industry and consulting representatives of the Utah Mining Association and the Colorado Mining Association made presentations. In Birmingham, Alabama, atmospheric monitoring system representatives, NIOSH researchers, representatives of coal mining companies, and UMWA workers from two Alabama mining companies made presentations. In addition, a staff member of The Center for Regulatory Effectiveness also presented comments to the Panel. In conjunction with the meetings in Salt Lake City and Birmingham, three-member subcommittees of the Technical Study Panel made field visits to the Skyline Mine, the Aberdeen Mine, and the Jim Walter Resources Mine No. 4. The mine visits were scheduled to see first-hand the mining conditions under which belt air was being utilized as an additional source of intake air for working sections.

By G. J. Conroy

This Bureau of Mines study was initiated to determine whether or not a large-scale investigation of 400-Hz applications in coal mines was justified as a means of increasing safety in operations due to size and weight reductions in portable and other mining machinery. Potential uses for 400-Hz power in mining operations are explored, and cost and size comparisons with 60-Hz systems are made. The use of variable-frequency motor drive is suggested for conveyors. The conclusion was reached that there is no significant potential safety increase due to a general size and weight reduction, as the fact of such general reduction cannot be demonstrated.

Jan 1, 1974

By O. C. Blade

A summary of the characteristics of motor gasoline for the winter 1951-52 is presented in table I, and for comparison, a similar summary for the winter 1950-51 is shown in table 2. Trends of some of the more important characteristics over a period of years are shown in figures 1 and 2. The results of this survey show that octane numbers have risen slightly since the summer of 1951 but are below the record levels of the winter of 1950-51. The fractions of a unit change since the summer preceding have resulted in the research and motor-method octane values being virtually the same as the figures for the survey of summer 1950. In volatility characteristics the winter gasolines have changed very little. Average Reid vapor pressures are 10.5 pounds for both grades of fuel compared to 10.4 and 10.5 pounds for premium and regular-price gasolines, respectively, of the winter of 1950-51.

Jan 1, 1952

By Andrew M. Leszcykowski

The Bureau of Mines (Bureau) conducted mineral investigations of the Payette Crest-South Fork area in west central Idaho near McCall, Idaho, in 1989. There are no known producing mines or mineral production from the area. Forty-seven samples were taken (stream sediment, rock. and placer); no identified mineral resources were delineated.

Jan 1, 1991

By L. H. ADAMS, C. N. HASKINS, J. K. CLEMENT

In the course of its investigations of the fuel resources in the United States and of the methods by which these resources could be utilized with greatest efficiency, the United States Geological Survey tested a great variety of coals and lignites as gas-producer fuel. Early in these testa it was found that many factors controlling the formation of gas in the generating chamber of the producer and, consequently, having a direct bearing on the management of producer-gas plants, were not as well understood as they should be. The Geological Survey therefore took up a detailed investigation of the chemical and physical processes that take place in the producer, keeping in view not only the possibility of increasing the efficiency of the producer as a source of energy, and the ensuing benefits to the public of cheaper power and greater utilization of low-grade fuels, but also the application of the results to the problems of boiler-furnace operations. - The Bureau of Mines, to which the testing and analyzing of fuels as carried on by the United States Geological Survey has been transferred, is continuing producer-gas investigations at the testing station at Pittsburg, Pa. Results of the gas-producer tests a made at the coal-testing plant erected at St. Louis, Mo., and of a study of some of the problems° that came up in the tests have been published by the Geological Survey. Results of the tests made at Norfolk, Va., and Pittsburg, Pa., and of further studies of particular problems, will be published by the Bureau of Mines. In the gas producer solid fuel is transformed into more readily combustible gaseous fuel. The transformation is relatively slow and consists of several processes: 1. The distillation of the volatile hydrocarbons from the freshly fired fuel at relatively low temperatures. 2. The combustion of the fuel by its combining with the oxygen of the air forming carbon dioxide (COO. 3. The formation of carbon monoxide (CO) and hydrogen (11 3), the essential constituents of producer gas, in accordance with the equations:

Jan 1, 1911

By H. D. Kline

Manganese ores have been mined in the Batesville district since 1849. Although not continuous over the intervening years, production had totaled approximately 432,000 tons of manganese ore and ferruginous manganese ore to the end of 1953. The ores occur in deposits, essentially low in manganese content, distributed over an east-west belt 24 miles long and 4 to 8 miles wide, the core of which is about 6 miles north of Batesville, Independence County. Although the reserves of high-grade ores in the district are comparatively small, the large deposits of subgrade ores and low-grade manganiferous material comprise potential sources of supply of manganese that may have increasing future importance. The manganese occurs as primary oxide and carbonate minerals in relatively flat-lying limestone and shale formations in which they were originally deposited and as oxides in residual clays resulting from decomposition of the shale and lime-stone. Most of the deposits underlie from a few to over a hundred feet of sedimentary chert, but many occur in the residual clays on exposed slopes of chert-covered hills.

Jan 1, 1956

By J. G. Kirby

According to the Bureau of Mines annual survey, there were 319 petroleum refineries in the United States as of January 1, 1957 capable of processing 9,123,674 [ ]-barrels of crude oil daily. This was the first time in eleven years that the total number of refineries increased. The crude throughput capacity of the refineries increased 491,284 barrels daily (6 percent) above the January 1, 1956 capacity. The East Coast and Texas Gulf Coast refining districts accounted for 60 percent of the additional capacity installed. Three new refineries were put into operation on the East Coast during the year with a total daily crude throughput capacity of 154,434 barrels while the other refineries in the district report a net loss in capacity, installing equipment capable of processing 140,000 barrels, but dismantling equipment with a capacity of 150,100 barrels. In the Texas Gulf Coast district, one new refinery with a daily crude oil capacity of 5,000 barrels was placed in operation in 1956 and 143,700 barrels of crude capacity was added to existing refineries. The capacity of the average refinery to process crude oil increased from 27,145 barrels daily to 28,601 barrels in 1956.

Jan 1, 1957