Search Documents

By R. E. Lindstrom, D. J. Bauer

Studies were conducted to assess the potential of naphthenic acid as a fractional extractant for rare- earth mixtures and yttrium in sulfate solution . Naphthenic acid was an effective extractant , and separation factors were favorable in the presence of aqueous phase chelating agents . Addition of EDTA to the naphthenic acid extraction system resulted in average separation factors of 2.2 between adjacent yttrium- group elements , whereas DTPA resulted in average separation factors of 3.5 between adjacent cerium- group elements . EDTA was of value in separating yttrium from the rare- earth elements . Thorium and uranium were preferentially extracted over the trivalent rare- earth elements by naphthenic acid .

Jan 1, 1964

By J. D. Kalasky, Stephen Krickovic

A degasification experiment was conducted in a Pocahontas No. 3 coalbed mine in Virginia. It involved (1) drilling holes in the coalbed in the out- side headings of a set of five being developed in virgin area, and (2) conducting a methane emission rate study as mining progressed and additional holes were drilled. Degasification from all drill holes except the longest in each of the outside headings and the first three drilled (excluding the in-situ pressure hole), was erratic and inconsequential in methane emission rates. The two longest holes liberated 66 and 79 cfm of methane, which is significant for the coalbed, but such quantity lasted a relatively short time; the first three were uniform but low in methane emission.

Jan 1, 1972

By John J. Sammarco

This report (System Safety Guidance 5.1) is the sixth in a nine-part series of recommendations and guidance addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various lifecycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction (Part 1).—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing system/software safety program. • 2.1 System Safety (Part 2) and 2.2 Software Safety (Part 3).—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g]and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File (Part 4).—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meet the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full life cycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment (Part 5).—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. The guidance reports comprise parts 6 through 9 of the series and are listed below: [< 5.1 System Safety Guidance (Part 6).—This guidance supplements 2.1 System Safety. < 5.2 Software Safety Guidance (Part 7).—This guidance supplements 2.2 Software Safety. < 6.0 Safety File Guidance (Part 8).—This guidance supplements 3.0 Safety File. < 7.0 Independent Functional Safety Assessment Guidance (Part 9).—This guidance supplements 4.0 Independent Functional Safety Assessment.] [ ]

Jan 8, 2005

By John J. Sammarco

This report (Safety File Guidance 6.0) is the eighth in a nine-part series of recommendations and guidance addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction (Part 1).—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing a system/software safety program. • 2.1 System Safety (Part 2) and 2.2 Software Safety (Part 3).—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g]and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File (Part 4).—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meet the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full life cycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment (Part 5).—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. The guidance reports comprise parts 6 through 9 of the series and are listed below: [5.1System Safety Guidance (Part 6).—This guidance supplements 2.1 System Safety. < 5.2 Software Safety Guidance (Part 7).—This guidance supplements 2.2 Software Safety. < 6.0 Safety File Guidance (Part 8).—This guidance supplements 3.0 Safety File. < 7.0 Independent Functional Safety Assessment Guidance (Part 9).—This guidance supplements 4.0 Independent Functional Safety Assessment.] [ ]

Jan 4, 2006

"One of the functions of the United States Bureau of Mines is to investigate the ability of electrical mining equipment to operate in a gassy mine without danger of igniting explosive atmospheres. To accomplish this purpose, tests are made in which mixtures of gas and air are ignited in the equipment while it is surrounded by explosive atmospheres of the same composition. In such tests, records of pressures developed by the internal ex-plosions are obtained and observations are made of any flames, sparks, or smoke which may issue from bearings and joints. Occasionally the explosion pressures in a mining machine rheostat or a compartment of some other machine reach a value which is judged to be excessive or abnormal.A number of factors are known to influence the explosion pressures, and both German and. British investigators have irate extensive research on their effects. Much of this work had been done with artificial compartment which certain conditions could c held, constant while others were being varied. The U. S. Bureau of Mines has not made any research on a scale to compare with that of the British or German investigators; however, special studies have been necessary from time to time to determine the cause and remedy for high pressures obtained in the routine test of some piece of mining machinery. Thus it has been possible to verify some of tee theories established on a purely experimental oasis by practical tests of machines as actually built for mine use.Some of the factors determined the pressure that will result when an explosive mixture in a compartment or connected compartment is ignited are: (1) The volume of explosive mixture ignited, (2) the percentage of as in the mixture, (3) the amount of coal-dust in the compartment or compartments, (4) the degree of movement or turbulence of the mixture at the time of ignition, (6) tightness of the joints and bearings, (6) the size of opening between, compartments, (7) the distance between the point of ignition and openings, and (8) the cooling, effect of surfaces and of material inclosed in the compartments."

Dec 1, 1929

By Roy L. Wilfong

The linear expansion of high-purity oxides of yttrium, cerium, samarium, europium, and dysprosium was determined by the interferometric method for the temperature range 25° to 1,000° C. Single-crystal magnesium oxide and single-crystal aluminum oxide were used as reference materials. The bulk density and crystal form of the nonreference materials also were determined. The coefficients of linear expansion in the range 25° to 1,000° C were found to be 8.10 x 10-6 for yttria, 12.10 x 10-6 for ceria, 10.81 x 10&apos;6 for samaria (monoclinic), 10.35 x 10-6 for europia (monoclinic), and 8.13 x 10-6 for dysprosia, each given in centimeters per centimeter per degree Centigrade. A detailed investigation of the interferometric technique for measuring thermal expansion in this temperature range was made. The interferometer was found to be a precise tool but only when adequate precautions were taken. These precautions are described.

Jan 1, 1963

By A. G. Starliper

Laboratory studies were made to produce whiskers of tungsten over a wide range of operating temperatures. Hydrogen reduction of tungsten hexachloride in a vacuum furnace at temperatures from 2,7000 to 3,3000 C yielded a small quantity of tungsten whiskers, provided a low degree of supersaturation was maintained. Direct measurements of 3,000,000 to 4,000,000 psi were obtained for the ultimate tensile strengths of individual whiskers averaging 3 to 4 microns in diameter with average aspect ratios of 1,000. This compares with strengths of 300,000 to 400,000 psi for 13-micron-diameter commercial filaments.

Jan 1, 1968

By Raymond Derzay

This publication is intended to be of value to the mineral industry in establishing and maintaining effective programs for preventing noise-induced hearing loss. Factors involved in this loss and the need for and the requirements of an effective hearing conservation program are discussed. The legal and legislative history of compensation for hearing loss is briefly reviewed. A review of statutes is not attempted since several States have recently modified) or are in the process of modifying their laws regarding permissible noise exposures) required hearing protection) and/or compensation for hearing loss. A review of other aspects of the problem of industrial noise in terms of medical, physiological) and psychological frames of reference is included. A hearing conservation program is described in detail. Appendixes detailing the names and addresses of a few equipment suppliers are included. References are provided for those who may wish to delve more deeply into the medical, technical, and scientific considerations of noise and its effect on man.

Jan 1, 1972

By J. W. Eckerd, W. S. Sanner, P. L. Woolf, R. E. McKeever

The Bureau of Mines experimental blast furnace was operated successfully with anthracite metallurgical briquets . Tuyère pressures were higher and more erratic than for operations using coke , and furnace " hangs " occurred more frequently . Higher hot - blast temperatures were required to maintain the quality of the metal . By using higher hot blast temperatures , the fuel and production rates and slag volumes were comparable to those obtained for all - coke operation . The anthracite metallurgical briquets exhibited excellent mechanical strength and descended through the shaft of the furnace with little breakage or reduction in size .

Jan 1, 1964

By M. W. Von Bernewitz

Corduroy is used for saving gold in small Land large milling plants throughout the world. Investigations by the Metallurgical Division of the Bureau of Mine indicate that corduroy blankets, used with or without a trap or jig in the mill classifier circuit, often are effective in concentrating gold and sulfides, especially if the gold does not amalgamate readily and if not enough sulfides are present to warrant the use of a shaking table, flotation cells, or cyanide plant. Most cold-mining countries include several or many small miner, that produce siliceous ores low in sulfides and gold, which can easily be amalgamated or caught in traps or jigs or on corduroy and shaking tables. At these mines the ore is crushed by stamps or bill mills, and the flow sheets include plates, flotation cells, and cyanide treatment, yet probably nearly as much of the pair minerals may be recovered by the less expensive plant. A well-known western maker of mine and mill equipment asserts, as the result of considerable observation of installed plants, that old and other valuable minerals should be caught as soon as they have been released by a mill, end recommends jigs to do this. A supplier of corduroy has informed us that at some mines this material is being replaced by jigs that catch gold as fine as 400-mesh. But for the small operator, inexpensive equipment such as a corduroy table may be better adapted and give a good recovery of gold and associated minerals.

Jan 1, 1939

By M. C. McCall

When electric current of any appreciable magnitude flows from a power line into the earth, a change sometimes takes place in the conditions of resistivity immediately surrounding the electrode or medium of contact. If the conducting medium is composed of moist earth or clay the effect is to increase rapidly the resistance. If the conducting medium is coal or a coal bed, the effect is one of slowly decreasing resistance as the coal is carbonized, If, however, the flow of current is not enough to carbonize the coal, it will dry slowly, with a resultant increase in resistance. Measuring ground resistance, or impedance, with conventional commercial ground testers does not always indicate the current that will flow in the earth circuit from a direct-current or an alternating-current power circuit. The exact reason for this has not been determined however, it is thought to be due to the comparatively minute currents used for such testing. A typical ground, tester used by the authors for this work indicated a maximum current of 25 milli-amperes. The frequency of this testing current also has an effect on the readings in all probability. While the possibilities of the effects of varying frequencies has by no means been fully explored in this investigation, there are very definite indications that the impedance of a circuit through a section of earth will vary in some inverse relationship to the frequency of the applied voltages. This is evident at ordinary power-line frequencies ns well as at higher frequencies up to 200 kilocycles, which was the highest frequency available for tests in this investigation. This report is written in the hope that it will stimulate further investigation of the possibilities suggested for communication and the development of safety devices for increased electrical safety in coal mining.

Jan 1, 1952

By R. Burrell, N .. L. Lapp

"Except for asthma and pulmonary infections, the types of lung disease that have been of immunologic interest the longest are the various mineral pneumoconioses. Because of their chronicity, type of pathology produced, and well-known immunotoxic properties associated with the dusts inciting them, the pneumoconioses have long drawn attention to the possibility that the immune system has not only been modulated but that its effectors have possibly contributed to their pathogenesis. All of the mineral dusts reviewed here have definite immunomodulating properties and act on various cellular and molecular components of the immune system. Further, each has an immunotoxic potential to induce either hypersensitivity (as in the case of beryllium) or other types of immune injury. This article reviews the immunologic aspects of the four major occupational minerals that have an immunologic impact on the lung: asbestos (particularly chrysotile), silica or quartz, beryllium, and coal mine dust.These agents have many things in common, yet each is distinctive. Although the possibility still exists that these mineral particles can adsorb intrinsic tissue antigens or extrinsic organic antigens to their surfaces and initiate immune responses to the adsorbed antigens, only one, beryllium, can act as an antigen itself. Silica is a profound macrophage toxin and thereby exerts many effects on those factors controlled by macrophages. Asbestos has undergone the most immunologic studies resulting in a much dearer picture of how it may contribute to immunopathology. Coal mine dust is the agent about which least is known immunologically, partly because there is no such thing as purified coal mine dust or a standard by which coal mine dust can be defined. Indeed, there are studies that use only the dust from the ground coal itself, whereas other studies use the total dust collected from air samples of a working mine in the belief that other types of dusts (e.g., silica from roof bolt drilling, from sand ground on the rails by cars, and from surface drilling) contribute to the disease (Figs. 1 to 5). This properly is coal mine dust and is poorly characterized. Yet, workers exposed to these dusts share similar reactive characteristics and they may be considered collectively as well as individually."

Mar 1, 1992

By Oliver C. Ralston

The growing popularity of perlite (sometimes spelled pearlite) as a raw material for thermal expansion into pumicelike products in the Western States has prompted a preliminary investigation of the properties of such material and the problems that want solution to put a perlite industry on a firm foundation. The Bureau of Mines is undertaking the gathering of data and the solution of these problems, and the following paper records some of the available information. and the promise of the material, with some comparisons of advantages of the various competing lightweight aggregates that can be made from siliceous volcanic glasses and rocks containing entrapped or dissolved water that causes their expansion on&apos; quick heating to their softening points. This new industrial rock has caught the fancy of the mineral industry in the western States because it has Fume advantages over natural pumice. Chemically, it is typified as rhyolitic in composition, and one may find obsidian, rhyolite, pumice, pumicite, and perlite from the same vant and contemporaneous in origin. The material need not be rhyolite but should be a siliceous or acid lava and contain 2 to 5 percent water still in "solution" in the rock. On quick heating to the softening temperature the material puffs, due to conversion of the contained eater into bubbles of steam. Slow heating causes gradual release of the imprisoned water by decrepitation and. cracking and-results in, very little puffing. Perlite is often in the form of ovoid volcanic bombs formed by explosive eruption of large masses of lava into the air, where they, quickly cool, with escape of little of the contained water, exceptt perhaps for a hollow interior. Since they cool in layers they have an onion-type structure and a pearly luster from interference of light between the. layers, which is&apos; the origin of the name "perlite." Perlite may occur in intruded flows that have been quickly cooled and partly expanded but retained most of their magmatic water content. Obsidian may be the same lava cooled quickly under conditions that prevented crystallization of feldspars and other minerals, leaving the volcanic glass that may or may not retain all of the original contained water.

Jan 1, 1946

By L. B. Berger

This information circular is a revision of I.C. 7238, Danger from Carbon Monoxide in the Home, by L. B. Berger and H. H. Schrenk, issued in April 1943. Each winter brings its toll of deaths and serious accidents from the deadly gas, carbon monoxide. Newspapers carry warnings to the public of the, dangers of this gas, and frequent news items report the finding of persons dead at unconscious from the effects of carbon monoxide, yet these accidents continue. Either these warnings are not read, or they are unheeded by people who feel that, "It can&apos;t happen to me." It can happen to you carbon monoxide is no respecter of persons.

Jan 1, 1954

By C. W. Davis

This is the first of a series of papers being; prepared as the work progresses in a study of the hydrometallurgy of manganese. The investigation is being made in an endeavor to make possible the utilization of lour-grade domestic manganese ores. The value of a hydrometallurgical process for manganese depends on the present and future uses for manganese products.

Jan 1, 1930

By C. M. McCulloch

The methane content of virgin bituminous coalbed can now be measured accurately in the field with exploration core samples from vertical boreholes. The gas content of the coal per unit weight can be used either to design a mine ventilation system or to determine if degasification of the coalbed will be necessary before mining, and to determine the gas resources in the coalbed. The equipment necessary to conduct the test costs less than $50. The gas con-tent of the coal in place in the ground is determined by summing the gas lost from coring, gas measured during desorption, and the residual gas in the coal. Upon removal from the borehole, the core sample is placed in an airtight container and des orbed for several weeks until the desorption rate is below 0.05 cm3/g for 5 consecutive days. The gas lost from the core while it was being cored and the residual gas are estimated by a new graphical method. The amount of gas remaining depends upon whether the coal is friable or blocky. Friability appears to relate to the depth of the sample below the surface, fixed carbon percentage, Hardgrove grindability index, and proximity to tectonic disturbance. Friable coals emit nearly 96 pct of the total gas during desorption whereas a blocky coal emits only 60 pct of its total gas. Coalbeds that are ill defined as to their blocky or friable nature must be tested in the laboratory for unambiguous analysis.

Jan 1, 1975

By D. J. Donaven, Manuel Gomez, W. S. Landers

Bulk density tests were made on a Western U.S. coke oven plant blend to obtain bulk density control data that would be directly transferable to plant practice . Maximum bulk density values were obtained at zero surface moisture . Increase in surface moisture to about 6 percent decreased the bulk density to a minimum value . Increase in the fine grinding of the blend , at constant surface moisture , decreased the bulk density . The effect of oil on bulk density was observed with five oils at concentrations ranging from 1/8 to 1-1 / 2 gallons per ton . Maximum bulk densities were obtained within the 1 / 2- to 1 - gallon - per - ton range . Essentially the same bulk densities were obtained with petrolatum- and nonpetrolatum- containing oils . Storage effects were observed on samples tested at selected intervals from 0 to 56 days . No significant change in bulk density took place if no surface moisture was lost during storage .

Jan 1, 1964

By James H. Cobbs

The purpose of this study is to investigate the application of boring equipment to the production of anthracite coal from steeply pitching beds. Both raise boring and augering equipment were considered. Previous studies (11) have indicated that boring equipment may have definite applications to the development of steeply pitching anthracite beds. This investigation was to carry forward previous work to determine the possible application of the two different types of equipment being considered. Previous conclusions have been substantiated by the results of this study.

Jan 1, 1975

By J. W. Walkiewicz

Studies were conducted by the Bureau of Mines to develop a method for fabricating Sm-Co permanent magnets. This method consisted of arc-melting, crushing and grinding the alloy, alining and pressing the powder, and sintering the green compacts. Results indicated that the optimum composition was 36.7±0.3 weight-percent Sm and 63.3±0.3 weight-percent Co. This composition was obtained by blending together Sm2C07 and SmCo5. The maximum values exper¬imentally obtained were MHC = 27.4 kOe, BHc = 7,510 Oe, Br = 7,810 G, and (BH)max = 15.1 MGOe. The optimum sintering temperatures and grinding times for maximum MHc and (BH)max were determined. Lowering the grinding temperature from 0° C to -60° C resulted in a significant increase of magnetic properties.

Jan 1, 1973

By A. B. Campbell

The Bureau of Mines is developing alloys using ion implantation as an alternative to bulk alloys that consume large quantities of strategic materials such as chromium and nickel. These alloys are formed at the outer layer of relatively common materials. To more fully understand the corrosion characteristics and physical properties of this outer layer, it was necessary to deter-mine the alloy concentration as a function of depth into the substrate material. Also, since many of the ion-implanted alloys would be utilized at elevated temperatures, it was necessary to determine the diffusion behavior of the implanted element. Proton-induced X-ray emission and inert gas ion sputtering have been utilized to generate composition depth profiles for Fe-Cr, Fe-Ni, and Fe-AI ion implanted alloys fabricated by implanting 25-kev Cr+, Ni+, or AI+ into iron substrates. The data were fitted (utilizing a computer program) with symmetrical Gaussian profiles yielding values for the range and range straggle of the ions. These parameters were then compared with those calculated from theory. Changes in the profiles due to annealing were investigated and values for the diffusion coefficient were obtained assuming diffusion according to Fick&apos;s Law. For the Cr+ and Ni+ implantation, the profiles as-implanted agree reason-ably well with theory and exhibit ?norrmal" diffusion characteristics at 500° C. For the Al+ implantation, the profile as-implanted is much broader than predicted and exhibits substantial enhanced diffusion at temperatures up to 500° C.

Jan 1, 1979