Search Documents

By A. L. Engel

Simple treatment methods, employing the least possible equipment, can sometimes be established for marginal ores and economical results achieved. In continuation of a long-established part of the hydrometallurgical and ore-dressing program of the Reno Station of the Bureau of Mines, typical ores from newly discovered or recently explored mining districts have been investigated. The purpose of such investigations is to encourage the search for and development of mineral resources and particularly to assist in the economical exploitation of low-grade and marginal ores, as well as the conservation and recovery of values in products from former operations that were discarded because of past inability to treat them economically. Several of these investigations have been limited to preliminary tests of samples from prospecting operations, whereas some involved samples of old dumps or tailings piles. The test, work in these cases was not extensive enough to warrant publication as individual reports, but is of considerable interest inasmuch as it indicates the possibilities as well as the limitations of treating the respective materials; and because, inasmuch as the samples were representative of the districts from which they were obtained, this in-formation should be helpful in the future development of these districts. The present report is a compilation of results of brief preliminary tests on oxide ores only, which contained gold and silver and in some cases base metals. The methods of treatment used include gravity concentration, amalgamation, flotation, and cyanidation. For the most part, only standard laboratory procedures were employed. No attempts were made to develop new methods for the low-grade refractory ores in this group of samples if simple treatment was not successful, as the stage of development of the properties did not warrant extensive experimentation on the samples submitted.

Jan 1, 1951

By Harold E. Marr

Energy dispersion X-ray analysis was evaluated for possible application in the secondary metals industries for the rapid analysis and identification of copper-base alloys. Laboratory investigations of standard brass and bronze samples indicate that X-ray methods are capable of separating standard alloys into 10 general classes with analytical times of less than 3 seconds per sample for clean, flat samples. A radioactive source of americium 241 with a secondary fluorescer was used as an excitation source, and a lithium-drifted silicon semiconductor detector was utilized for energy discrimination of X-rays.

Jan 1, 1974

By W. M. Traver

During World War II, the Bureau of Mines investigated a large number of ore deposits in the United States and Alaska in a search for domestic sources of strategic minerals. Deposits chosen for exploration included those expected to contain metals of importance in the successful prosecution of the war. This report describes exploration of a district of known antimony occurrence on Coyote or Antimony Creek near Antimony, Garfield County, Utah. A preliminary report by Paul T. Allsman, Chief of the Bureau's Salt Lake City branch made in August 1941, recommended further investigation, and proposed methods for performing the work. The project, begun in November 1941 and completed in January 1942, included trenching and sampling in four of the most promising parts of the area The Federal Geological Survey cooperated in the work by detailed mapping and assisted in the interpretation of geologic data.

Jan 1, 1949

By John C. Machisak

INJURY DATA and experience at coal mines in the United States for 1957 are presented in this bulletin under the following general sections: (A) General injury experience: Tables 1-6: Current data on number of fatal and nonfatal injuries, frequency and severity rates, and average severity. (B) Selected injury experience: Tables 7-36: Current data on causes of injuries, distribution of injuries by part of body injured, days of disability, extent of hand and machine loading, experience by employ¬ment and production groups, and various other operating factors and physical conditions related to the occurrence of injuries at the Nation's coal mines. (C) Injury experience, by States: Tables 37-41: Data on injuries, injury rates, employment, causes of injuries, and severity rates. (D) Major disasters: Table 42: Data on major disasters from 1948 to 1957. A major disaster is defined as a single accident in which, or as a result of which, five persons or more are killed instantly or die at any time thereafter. (E) Historical coal-mine-fatality experience: Tables 43-47: Data on fatalities and their causes at bituminous-coal, lignite, and anthracite mines from the earliest records through 1957.

Jan 1, 1960

By John D. Sullivan

In leaching copper ores knowledge of the rate of dissolution of the copper minerals and of the impurities is desirable. With knowledge of these two factors and data as to what minerals are present in the ore the metallurgist has an excellent start on planning a leach¬ing cycle to fit that ore. The rate of dissolution is rather difficult to predict, and the time required to leach a given ore may differ markedly from that required by another ore. The whole study as related to mixed oxidized and sulphide ores is one of relative rates of dissolution of the different copper minerals and the impurities in sulphuric acid and in ferric sulphate. The aim of leaching is to choose a cycle and strength of solvents to ex¬tract a maximum amount of copper and a minimum of impurities. The consumption of reagents per unit of copper dissolved is a function of the strength of the reagents used and the relative rates of attack on copper minerals and impurities. An opportunity may exist of ob¬taining the kind of electrolyte wanted for electrolytic precipitation and yet of saving on the consumption of reagents by modifying the strength of ferric sulphate and of sulphuric acid during the cycle to fit the time needed for dissolving the sulphide and oxidized minerals present. Former papers have considered the rate of dissolution of azurite, malachite, tenorite, chrysocolla, cuprite, chalcocite, boruite, and covellite in common leaching solvents. A paper soon to be written will consider some of the less important copper minerals. The present paper considers the rate of dissolution of copper from ores of the Southwest in sulphuric acid of varying strength and the ratio of sulphuric acid consumed to copper dis¬solved. In this study two ores containing the copper principally in an oxidized condition were used. A study of other ores, especially those containing high percentages of sulphide copper minerals, would be desirable, but since consumption of acid has paramount interest,

Jan 1, 1931

The Federal Coal Mine Health and Safety Act of 1969 requires that each operator of a coal mine shall take accurate samples of the amount of respirable dust in the mine atmosphere to which each miner is exposed, a measure designed to prevent the development of coal workers' pneumoconiosis. This textbook manual is used in the training of personnel to operate respirable dust sampling devices and to conduct sampling programs. It contains the portions of the act applicable to respirable dust standards, the procedures to be followed to insure compliance with Federal regulations, and descriptions of sampling devices.

Jan 1, 1971

By John D. Sullivan

In leaching copper ores knowledge of the rate of dissolution of the copper minerals and of the impurities is desirable. With knowledge of these two factors and data as to what minerals are present in the ore the metallurgist has an excellent start on planning a leaching cycle to fit that ore. The rate of dissolution is rather difficult to predict, and the time required to leach a given ore may differ markedly from that required by another ore. The whole study as related to mixed oxidized and sulphide ores is one of relative rates of dissolution of the different copper minerals and the impurities in sulphuric aoid and in ferric sulphate. The aim of leaching is to choose a cycle and strength of solvents to extract a maximum amount of copper and a minimum of impurities. The consumption of reagents per unit of copper dissolved is a function of the strength of the reagents used and the relative rates of attack on copper minerals and impurities. An opportunity may exist of obtaining the kind of electrolyte wanted for electrolytic precipitation and yet of saving on the consumption of reagents by modifying the strength of ferric sulphate and of sulphuric acid during the cycle to fit the time needed for dissolving the sulphide and oxidized minerals present.

Jan 1, 1931

By Thomas O. Llewellyn

This U.S. Bureau of Mines (US8M) report presents a concise review on sources, processes, supply, and historical use patterns of domestic cadmium. It also covers a preliminary estimated cadmium material balance for the year 1989.

Jan 1, 1992

By W. H. Coghill, B. W. Gandrud, F. D. DeVaney

"The self-fluxing iron ores of Alabama are the foundation of the thriving iron and steel industry of that State. In addition to these deposits of self fluxing ores there are seams containing practically the same percentages of iron but too much silica. These ores at present are valueless, but if they could be concentrated by reducing the silica content, the ore reserves of the Birmingham district would be greatly augmented. A detailed report on the iron-ore deposits of the district, describing the types of ore and their extent, has been published.In forwarding its mineral conservation policies the United States Bureau of Mines has given some attention to the siliceous ores of this district.The low cost of gravity concentration gives this process first rank in the beneficiation of iron ores. For this reason many experimenters have tried to concentrate the Alabama iron ores on tables. In the face of the early failures a new trial has been made and the results have justified the effort.In this work more attention than formerly has been given to the physical, properties of the ores. The removable siliceous gangue is in the form of oolitic grains which ""shell"" out like corn, leaving the hematite as rich high-grade ""slime"" and as clean granular grains. The ""slime concentrate"" may be recovered by well known desliming processes. The oolitic grains and granular hematite are separated on tables."

May 1, 1929

By G. V. Sullivan

The Bureau of Mines conducted preliminary beneficiation studies of a gold-bearing graphitic schist from Blue Hill, Tallapoosa County, Ala. The average analysis of the material was 0.08 oz/ton gold. Tabling of minus 35-mesh material recovered 83 to 94 percent of the gold at grades of 6.925 to 2.165 oz/ton, respectively. A combination of jigging and tabling resulted in a concentrate assaying 24.3 oz/ton gold and contained 87 percent of the total gold. Treatment of the material by jigging, tabling, and amalgamation recovered 86.5 percent of the gold.

Jan 1, 1969

By R. A. Beall

This paper summarizes the development of a furnace for producing titanium castings. The general problem is outlined and chronological details are given on the construction and operation of four different casting furnaces, all utilizing consumable-electrode arc heating and water-cooled copper crucibles. Of the two methods of pouring, the tilt-pour technique has been more satisfactory than bottom tapping. Mold design, electrode fabrication, and deep-pool production are discussed. INTRODUCTION In the early summer of 1953 the Bureau of Mines was contacted by the Department of the Army through Watertown Arsenal to explore the possibility of conducting research on casting titanium metal. The objective of the program was "to develop a technique for producing formed castings of titanium metal not less than 40 pounds in weight and without introduction of deleterious contamination."

Jan 1, 1956

By W. A. Stickney, J. W. Town

Studies on continuous - circuit leach - aluminum precipitation and leachelectrodeposition of mercury were made by the Bureau of Mines to determine optimum conditions and cost estimates for recovering mercury from mercury sulfide flotation concentrates . With 150 grams of sodium sulfide and 50 grams of sodium hydroxide per liter , from 98 to 99.8 percent of the mercury was extracted from flotation concentrates , with about 0.5 pound of sodium hydroxide used per pound of mercury produced . Precipitation of mercury from the caustic - sulfide solution with minus 8 - mesh aluminum shot required about 0.2 pound of aluminum per pound of mercury produced at a cost of $ 0.05 per pound of mercury . Electrodeposition cost with 7 mill power , based on 50 percent current efficiency , was below 2 mills per pound of metal deposited . Feed solutions ranged from 10 to 130 grams of mercury per liter , and current densities , from 2 to 70 amperes per square foot . The cost of open- pit mining 250 tons per day was estimated at $ 1.75 per ton , and flotation - leachingelectrodeposition of the ore , at $ 3.54 , resulting in a cutoff grade of about 0.1 percent mercury . The cost of underground mining 50 tons per day was estimated at $ 20.00 per ton , and the cost of milling the ore was estimated at $ 13.33 , which resulted in a cutoff grade of 0.6 percent mercury .

Jan 1, 1964

By John R. Hoskins

Uniaxial compressive strength of rock is usually determined in the laboratory from cylindrical samples that vary in diameter from 5/8 to 8 inches, using a spherically seated compression head of unspecified size. The Bureau of Mines conducted a series of tests on limestone, marble, sand-stone, granite, and plaster of paris to determine the influence of the spherical head sizes and the specimen diameters themselves on the uniaxial compressive strength. Cylindrical samples of several different diameters of each rock type, all having a length of twice their diameter, were prepared and broken using at least three different diameter spherical heads. Analysis of the data shows that spherical head size does not significantly affect the uniaxial compressive strength of cylindrical rock samples. However, the diameter of the rock specimens does significantly affect the uniaxial compressive strength. Within the range of specimen diameters tested, a coefficient of variation of 6.4 percent for plaster of paris can be attributed to the selection of specimen diameter alone. Similarly, a maximum coefficient of variation of 4.7 percent for the rock types tested can be attributed to the specimen diameter alone.

Jan 1, 1969

By E. J. Lintner

This paper is one of a series being prepared by the Bureau of Mines describing; gypsum mining and crushing methods and costs at various operations throughout the, United States. These papers are designed to dissemminate technical information regarding methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs may in many instances cause embarrassment to the individual operator as well as to the industry as a whole; on the other hand, operating costs are essential to the technical discussion and. study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulation shall ensue. The following report deals specifically with the mining and primary crushing methods employed at the plant of the Ebsary Gypsum Co., Inc., Wheatland, Monroe County, N. Y. This company is capable of maintaining a maximum yearly production of 220,000 tons of crushed gypsum, thereby ranking as one of the largest gypsum operators of the State. The methods and practices employed typify the standard methods followed by gypsum producers in western Now York State, The bed of gypsum mined lies only 35 feet beneath the surface and is above average thickness for this vicinity.

Jan 1, 1937

By J. C. Barrett

Bureau of Mines research on the arc welding characteristics of titanium was initiated in 1948. Little was known about the art except that the easily contaminated metal required more protection from the atmosphere during welding than most other metals. Chambers were designed and built within which titanium could be welded with adequate inert gas protection. Welds were made and their properties studied, and prototype items were made successfully. This report, presenting a resume of the titanium arc-welding experiments undertaken by the Bureau of Mines, demonstrates that the process is successful if conducted under proper conditions and describes the welding of prototypes. INTRODUCTION The Bureau of Mines' first report on methods of joining titanium covered the subject of spot welding,4/ outlining the conditions necessary for producing spot welds in ductile titanium consolidated by powder metallurgy methods and describing the characteristics of such welds. This report embraces the field of fusion weld-ing of titanium and traces the development of suitable methods and equipment for producing such welds.

Jan 1, 1956

By B. W. Madsen

Bureau of Mines research to recover arsenic from mining industry waste material and process streams is reported. Batch and column approaches were investigated for adsorbing arsenic from acid leach solutions and ion-exchange eluate solutions with hydrated titanium dioxide granules. A method for producing hydrated titanium dioxide granules was devised to provide material suitable for use in a packed adsorption tower. Selective adsorption of arsenic from acidic leach solutions was achieved. The loading capacity of arsenic on the granules was 14 wt-pct when synthetic solutions were used, but lower when actual leach solutions were used. Other elements in the leach solution were Zn, Cd, and In. The granules were used in an attempt to lower the arsenic content in a solution containing 0.95 g/l W and 0.027 g/l As from a process devised by the Bureau of Mines to treat Searles Lake brine. The arsenic content was lowered to less than 0.001 g/l, but unacceptable amounts of tungsten also were adsorbed by the granules. Adsorbed tungsten was partially stripped with pH 11.5 NaOH, and both tungsten and arsenic were completely stripped with 5M NaOH solution. Repeated loading and stripping of the granules had no effect on the loading capacity for arsenic.

Jan 1, 1983

By G. R. Hopkins, E. M. SEELEY

According to reports received by the Bureau of Mines, Department of Commerce, as of Jamary 1, 1930, there were 1,035 natural-gasoline plants in the United States, with a total daily capacity of 10,516,000 gallons. (These data do not include one small plant in Alaska.) The last similar survey, that of Jamary 1, 1928, showed a total of 1,155 plants of 8,048,000 gallons daily capa- city. This in two years time the number of plants has decreased by 120, but the total capacity has increased 2,468,000 gallons or 31 per cent. This is roughly equivalent to the gain in production over the same periodi Over half of the increase in total capacity was registered in California, where the development of flush oil production having a comparatively high gas-oil ratio in such fields as Santa Fe Springs led to construction of some new plants and material enlargement of others. Of the total plants, 999 were operating on Jamary 1, 1930, and 36 were shut down. This compares with 1,060 operating and 95 shut down two years ago, which indicates a tendency to dismantle plants as soon as they become obsolete or umrofitable. The total daily capacity of the plants operating on Jamiary 1, 1930, amounted to 10,278,000 gallons, or 98 per cent of the total, leaving only 238,000 gallons, or 2 per cent, for the shut-down plants. This contrasts with the refining industry, which usually has 5 per cent of its total capacity idle; the difference is due to the relative ease with which a refiner can secure a crude supply as against the difficulty the natural gasoline manufacturer has in reestablishing his gas connections. During 1929 the average total daily capacity of the operating plants was 9,899,000 gallons, while the average daily production amounted to 6,015,000 gallons. This indicates that the plants operated during 1929 at 61 per cent of their capacity. Although over 60 plants were dismantled in Oklahoma during 1929 the State continued to rank first in total mumber. California was second in mumber of plants with 165, and was one of the few States that showed a gain since the

Jul 1, 1930

By E. G. King

This publication presents original thermal data for a typical variety of perlite and supplies basic information for use in computing energy requirements in processes for expanding perlite. Perlite has been defined by Raiston 4/ as any silicious lava containing dissolved water in sufficient amount to errand into bubbles when the material is quickly heated to a suitable point in the softening range." The uses of expanded perlite in) the construction and ceramic industries have been discussed by Ralston 4/ and King. 5/ The work described here had a dual purpose: (1) It was desired to ascertain quantitatively, using a typical variety of perlite, just how firmly the contained water is held, and (2) it was desired to obtain basic thermal data sufficient for energy-requirement calculations in processes for expanding perlite.

Jan 1, 1948

By Friedel. Michael J.

The U.S. Bureau of Mines investigated acoustic emission (AE) and the Kaiser effect in six types of rock: St. Cloud gray granodiorite, Barre granite, Dresser basalt, Salem limestone, Berea sandstone, and a volcanic tuff. AE signatures were used for interpreting the rock deformation stage and for indicating mechanisms of failure in uniaxial compression. The research demonstrated the advantages of using the volumetric stress-strain curve, as opposed to the more conventional uniaxial curve, for correlating AE response signatures with deformation stages and fracture processes in the rock. Standardized experimental procedures were used for the AE monitoring. The Kaiser effect was shown to be capable of determining prestress levels to within a few percentage points in uniaxial compression tests. Also, prestress memory was shown to be retained in the rock for periods of up to at least. 5 months, the maximum period of testing. The Kaiser effect AE technology holds promise for providing a comparatively inexpensive and less complex method for examihing stress history in rock. However, since the conftning stress has a pronounced influence on the Kaiser effect, it must be considered in developing technology for determining peak fteld stresses based on the Kaiser effect.

Jan 1, 1990

By Joseph D. Davis, G. S. Scott, Palmer B. Place

In the course of investigations made by the Bureau of Mines in cooperation with the Trent Process Corporation, into the properties of mixtures of oil and coal, a comparative study was ma.de of the 'behavior of these mixtures and their cons ti tuents on destructive distillation. Mixtures of a petroleum oil and bitminous coal were first distilled under carefully controlled conditions, and then charges of the eame oil and coal were distilled separately under similar conditions. The quantity and quality of the distillation products were determined, and. resul. ts were compared. This comparison furnished a basis tor judging whether grea, ... er values in products can be obtained by distillation of oil and coal in mixtures than· b:, their separate distillation. In making the mixtures, the method used in t~e Trent process for cleaning coal was followed. The paste or plastic emulsion of oil and coal obtained is called "amalgam".••• When finely pulverized wet coal is mixed with approximately one-third its weight of. oil and agitated with a large excass of waj;er, the coal and oil agglomer-. ate to form a paste or amalgam. A large portion of the extraneous ash original.17 in the coal remains suspended in the water, with which it can be decanted from the amalgam. Ir the latter is now thoroughly drained and kneaded after the manner ot working butter, most of the excess water enclosed can be removed. This, .in brief, constitutes the Trent process for cleaning coal, The effectiveness of the process for cleaning coal has been studied••••. by the Bureau, and the results of the study show, in general, a high ash reduction an:l good recovery of combus ti bl e f'rom coals of medi ,mi and hi~ rg,nk. With coals of tht lowest rank, such as li@!Rlites, the process is only moderately auccessf'ul, owing to the difficulty attending the preparation of coherent amalgams, Oil losses to wate~ and refuse are small, and apparently it would be practical to rotate the same oil in the cleaning process if some efficient method were devised for recovering it from the amalgam, so a distillation process naturally suggested itself.

Dec 1, 1921