Search Documents

By W. C. McLaughlin

Under a cooperative agreement, the Bureau of Mines, Magma Copper Co., and ASARCO, Inc., tested backfilled ground support systems at t.wo elevations in Magma's San Manuel, AZ, mine. The tests were mainly for guidance in designing the loading crosscuts of the new ASARCO Sacaton underground mine. Two-piece, wide-flange steel sets for 8-by 8-ft (2.44-by 2.44-m) and 11-by II-ft (3.36-by 3.36-m) openings were designed. Set spacing was 3 ft (0.91 m) and 5 ft (1.52 m), respectively. After erection, the sets were lagged with various test materials. The void between the lining and the ground was backfilled with sand and pea gravel. Instruments measuring strain (used to determine changes in stress) were placed beneath the sets and in the backfill. Results indicate the backfilled sets in the smaller drift (2315 grizzly level, panels 6 and 7) of 8-by 8-ft (2.44-by 2.44-m) cross section are a viable permanent support system, lower in cost than the standard formed concrete. Results are inconclusive in 2615 grizzly level, panels 5 and 6, where wide-flange steel sets were used with 5-ft (1.52-m) long concrete gob lagging of T-design.

Jan 1, 1983

By Laxman S. Sundae

In the vast majority of American coal mines, roof bolt holes are drilled dry, mainly because of mine operator concern with the spent water creating adverse working conditions. Wet drilling, however, can increase drilling rates and the effective lifetime of the drill bits used. This study, carried out as part of an ongoing cooperative research program between the U.S. Bureau of Mines and the University of Missouri-Rolla, shows that the large volumes of water conventionally used in wet drilling are not necessary, and the performance benefits from wet drilling can be achieved with total volume flows on the order of 0.4 L per hole. This conclusion is validated based on the measured respirable dust generated in drilling Berea sandstone. The results are confirmed using a variety of bit shapes, which are also shown to have a significant effect on penetration rate.

Jan 1, 2010

By L. Hoogenboom

Under contract (H0232044) to the U.S. Bureau of Mines, Mechanical Technology Incorporated made an experimental investigation of the feasibility of measuring the load in roof bolts using a magnetostrictive sensor. The program was aimed at developing an inexpensive, moderately accurate, load-sensing element suitable for permanent installation and use underground. A combination of a cylindrical load-carrying sleeve under the bolt head and 3 removable circular multipole inductive sensor around the sleeve was tested. Program tasks included: design and fabrication of several sensors; design and manufacture of a large number of experimental sleeves; definition of electronic instrumentation specifications; design and manufacture of electronic sensor readout; and evaluation and testing of many sensor-sleeve combinations. Sleeves of different materials, various lengths, diameters and areas - with and without various nickel coatings -were combined with several experimental inductive sensors that were operated over a wide range of carrier frequencies.

Jan 1, 1974

By W. Bruce Montgomery

Manganese oxides occur, with some iron oxides, in small scattered lenses on property controlled by the Columbia Manganese Co. (1943) near Evington, Campbell County, Va. The company mined some manganese ore during 1917 and 1918. A preliminary examination in May 1942 indicated the possibility of finding additional ore. On August 21, 1942, the Bureau of Mines began prospecting to verify the continuity of the ore exposures. Work on this project continued until February 5, 1943. Prospecting and development work included shaft sinking, crosscutting, drifting, trenching, and test-pitting in six separate areas indicating two types of deposits. The most predominant type is a wide brecciated area in which occur lenses or pockets of nodular manganese oxides. The other type is characterized by more of a vein structure, including thin layers of manganese oxides.

Jan 1, 1949

By T. W. Johnson

The United States Bureau of Mines, in cooperation with the Natural Gas Department of the American Gas Association, has been studying actively for the past several years the flow of natural gas through high-pressure pipe lines. This report deals with that part of the study involving the design off pipe-line systems consisting of lines laid parallel to each other. The lines are referred to as the original line and the parallel line. The paralleling line may or may not extend the entire length of the original line; however, the parallel line is connected at its two ends to the original line. As a result of the large expansion of the natural-gas industry almost all markets within economic distance from the developed gas fields have at least one pipe line supplying them with natural gas. Small increases in the consumers' demand for natural gas can be met usually by increasing operating pressures, but any marked increase in demand necessitates paralleling sections of the existing systems. It is believed that to a large extent future

Jan 1, 1934

By Jon C. Volkwein

The Bureau of Mines, Foster-Miller Inc., and Beaver Creek Coal Co. have evaluated the ability of a new system to ventilate a 40-ft-deep cut. A remote-control continuous-mining machine, in a 7-ft-thick seam, with exhausting brattice was fitted with an improved sprayfan system plus additional forward and reverse pointing sprays. Static and dynamic tests using tracer gas were conducted in a full-scale model and under-ground to measure the effectiveness of exhaust face ventilation for various deep-cutting mine and spray configurations. When compared to a lO-ft primary ventilation brattice, the extended-cut spray system consistently provided better face ventilation at all configurations up to and including a 40-ft brattice setback. The system also provided good dust protection and visibility for the machine operator. Another safety advantage is the elimination of the need to set temporary roof supports to maintain the ventilation brattice.

Jan 1, 1985

By L. A. Haas

The Bureau of Mines conducted bench-scale leaching tests with recycled spent copper electrolytes and copper-nickel mattes produced from the Minnesota Duluth Complex concentrates. This report describes the first stage of an overall two-stage leach operation. The objective of this research was to determine the matte-leach technology required to convert spent copper electrolyte into an enriched nickel liquor suitable for a nickel refinery and there-fore essentially free of copper, iron, and sulfuric acid. The experimental variables investigated were matte composition, particle size, spent electrolyte content, pulp concentration, oxygenation, temperature, and time. The time required to produce an enriched purified nickel liquor decreased with increasing pulp concentration, temperature, and oxygenation, but increased with increasing particle size and electrolyte copper and acid content. Nickel-rich (about 50 g/l) liquors at a pH of about 4 and containing less than 1 g/l of copper and iron were produced at 70° C by leaching minus 325-mesh low-iron (less than 5 pct) matte for 8 hours with spent electrolyte containing 22.4 g/l Cu, 28.9 g/l Ni, less than 0.1 g/l Fe, and 50 g/l H2S04 at a pulp concentration of 1 kg of matte per liter of spent electrolyteo Varying the nickel content of the spent electrolyte from 11 to 101 g/l appeared to have no appreciable influence on the matte leaching characteristics.

Jan 1, 1981

By D. Bienstock

Using a nitrided fused-iron catalyst, the Bureau of Mines investigated the Fischer-Tropsch reaction in the oil-circulation process. The nitrided iron was quite stable and permitted the longest run obtained thus far in the oil-circulation process without the need for reactivating the catalyst--3,700 hours of operation. The effects of several operating variables--temperature, pressure, gas-recycle ratio, space velocity, synthesis-gas composition, and synthesis with and without reflux of oil to the reactor--on the production of oxygenates were studied. The importance of removing reflux oil and of high gas recycle in increasing the oxygenate content was shown. A finished gasoline containing 28 percent by weight alcohols was produced. The research octane number (RON) was 92.9 clear, increasing to 98.5 with the addition of one milliliter of tetraethyl lead (TEL). INTRODUCTION The Federal Bureau of Mines has been engaged since 1944 in a research and development program on the synthesis of gasoline from coal. Gasification of coal with steam and oxygen to yield a "synthesis gas"--a mixture of carbon monoxide and hydrogen--is being investigated at Morgantown, W. Va., and the synthesis of gasoline by catalytically reacting carbon monoxide and hydrogen over iron by the Fischer-Tropsch reaction is being investigated at Bruceton, Pa.

Jan 1, 1960

By M. R. Geer

The Bureau of Mines examined the washability data for 25 Appalachian coals requiring low-density washing to reduce sulfur content to 1 percent, using the distribution-curve method. The purpose was to estimate how closely theoretical sulfur values could be approached, what yields of washed coal could be expected, and the recovery efficiencies that might be achieved. Assuming that the run-of-mine coal would be crushed to 3/8 inch and cleaned in dense-medium cyclones, the calculations indicate that theoretical sulfur contents could be approached closely when cleaning at a specific gravity of separation as low as 1.30. With coals that have favorable specific gravity compositions the recovery efficiency anticipated for cleaning at 1.30 specific gravity is surprisingly high. Similar calculations for cleaning with concentrating tables at intermediate specific gravities indicated that theoretical sulfur contents at 1.50 specific gravity could be approached closely with some coals but not with others. The calculations suggest that operating a table at a specific gravity of separation much lower than about 1.50 probably would be unsatisfactory with most coals.

Jan 1, 1968

By H. M. Smith

[ ]

Jan 1, 1927

By H. V. Makar

The Bureau of Mines successfully demonstrated, on a pilot plant scale, a sodium sulfate (Na2S04) refining process for removal of copper from molten ferrous scrap. Previous tests established technical feasibility on a bench scale for achieving low copper concentrations and determining the principal factors controlling process efficiency. The pilot plant study involved a 1-ton arc furnace for melting ferrous scrap and a 1-1/2-ton treatment ladle. Results of these tests showed that copper removals obtained in laboratory tests (approximately 40 relative percent copper removal with 10 weight-percent surface addition of sodium sulfate) could be achieved on the pilot plant scale when excess carbon was added with the sodium sulfate compacts. Data were obtained on temperature losses and carbon consumption related to Na2SO4 treatment.

Jan 1, 1974

By William D. Mayercheck

The U.S. Bureau of Mines is conducting research aimed at providing technology for a low-cost, high-recovery, environmentally acceptable mining system to recover the vast thin-seam coal reserves existing in the mountainous areas of the Appalachian region in the Eastern United States. As part of this research, the Bureau is evaluating new techniques to address these coal resources. This report summarizes the results of a worldwide technical search on thin-seam coal mining, the formulation of various methodologies for mining mountaintop thin seams, and the implementation and status of a physical model test program to validate and further develop the most promising concept-the "roof-fall-tolerant" mining system.

Jan 1, 1990

By V. L. Burdick

A literature review of current uses of Mn02 in ceramic applications with suggestions for future research. Historical background, oceanographic distribution, geology, exploitation, law and politics. Uses of Mn02 in ferrites, semiconductors, catalytic processes, thermo-luminescence and photochromic materials. Select bibliography of 33 items, plus 129 references.

Jan 1, 1980

By Thomas M. Barczak

The U.s. Bureau of Mines is conducting research to optimize the utilization and design of mine roof support systems. This report describes methods to evaluate resultant loading on longwall shields, defined as external resultant vertical and horizontal force acting on the canopy and base. Four models are considered: two rigid-body models, an elastic model, and a numerical model. The rigid-body models equate measured internal shield forces to unknown external resultant shield forces (loads) through rigid-body analysis of static equilibrium requirements. The elastic model develops a solution to shield mechanics by evaluation of the load-displacement relationship and stiffness characteristics of the support structure. The numerical model is a two-dimensional finite-element representation of a shield structure. Model determination of resultant shield loading is compared to controlled loading of a shield in the Bureau's mine roof simulator. Parameters investigated are shield height, canopy contact configuration, canopy and base horizontal constrainment, and boundary conditions imposed by vertical and horizontal shield displacements. It is concluded that rigid-body models are most applicable to in situ measurement of shield loading. Applications requirements and potential error sources are discussed.

Jan 1, 1990

By J. M. Davidson

The potassium mineral polyhalite (K2SO4.MgSO4.2CaSO4.2H2O) found in large deposits in western Texas and southeastern New Mexico is associated with varying amounts of halite (sodium, chloride, NaCl) and anhydrite (calcium sulphate, CaSO4). Although the anhydrite, because of its low solubility and slow rate of solution, is relatively inert, the halite is dissolved immediately in any process solution with which the polyhalite comes in contact. Limited quantities of sodium chloride in the liquors used for the hot extraction of polyhalite materially improve the results obtained, but only a very small sodium chloride content may be desired in the entering polyhalite in other procedures, such as Bureau of Mines process. In all of the processes suggested for the recovery-of potassium sulphate from polyhalite the control of the sodium chloride content will be desirable, if not absolutely essential to efficient operation.

Jan 1, 1934

By John W. Moore

The discovery of porphyries in petroleum by Treibs (17-19) is one of the most significant achievements relating to the origin of petroleum. The presence of these remnants of chlorophyll and hematin in petroleum has immediate practical interest in several aspects of the petroleum industry. Because of their interfacial activities and film-forming tendencies, the metal-porphyrin complexes may be expected to affect the wettability of petroleum-reservoir rock surfaces and influence the flow of fluids in these reservoirs. Also, studies of the relationship of trace elements and porphyrins in petroleum may be expected to yield valuable information on source beds and petroleum migration. Finally, the extreme stability of several metal-porphyrin complexes complicates removal of these metals from some petroleum stocks where they exert deleterious effects on processing and utilization. Metal-porphyrin complexes are commonly associated with the asphaltic residues of crude oils in which they occur (8, 9, 15). However, investigations in this and another laboratory (15) show that small amounts of these complexes often remain in partly refined petroleum products, such as thermally cracked distillates and deasphalted stocks.

Jan 1, 1957

By P. D. Kovscek

The Bureau of Mines equipped a longwall shearer with a water-jet-assisted mechanical cutting system to determine the effect of the high-pressure sprays on machine performance, airborne dust levels generated, and size of particles formed. Testing was conducted on a simu-lated coal block (coalcrete) while cutting at a water pressure of 190 psi and at water-jet-assisted pressures ranging from 1,000 to 6,000 psi. The shearer motor energy used by the shearer while cutting coalcrete was determined for each cutting condition. Results indicate that the motor energy required by the shearer for each ton of material cut did not vary significantly as the water pressure was increased. Results of dust measurements recorded near the cutting drum indicate that at water pressures above 3,000 psi, dust reductions up to 85 pct were achieved com-pared with cutting with conventional sprays. Analysis of the particle size distribution during cutting showed that increasing the water pres-sure resulted in increased median particle size. In light of these results, various mechanisms for water-jet-assisted cutting are discussed.

Jan 1, 1986

By J. R. Koehler

The U.S. Bureau of Mines (USBM) ground control research program includes several projects focused on developing design criteria for yielding-pillar-based longwall gate road systems. As part of this program, mining practices at the Sunnyside Mines, Sunnyside Reclamation and Salvage Co., Sunnyside, UT, are being documented to preserve the long history of yield pillar system evolution on the property. Published information describing the specific in-mine performance of the numerous gate road configurations utilized at the Sunnyside Mines is very limited. To overcome this deficit, USBM personnel interviewed 30 longtime mine employees representing nearly 700 years of mining experience at the Sunnyside operations. Mining conditions in 12 specific areas in the Nos. 1, 2, and 3 Mines were discussed in the interviews. Also, broad topics such as general mining practices, safety, and geology were often addressed during the discussions. Comprising the body of this report is an extensive record of the events and conditions experienced while mining the identified areas. In addition, eight significant conclusions were developed that accurately summarize the general opinions of the interviewed personnel regarding mining conditions and practices at Sunnyside.

Jan 1, 1994

By Jr. Reed

Cassiterite was discovered in Coosa County, Ala. in 1880 by Judge John S. Bentley. Since that time intensive surface prospecting has revealed the presence of cassiterite in pegmatite bodies that occur in a zone about 20 miles long and 3 miles wide. Numerous trenches and test pits and several shafts were sunk, and one attempt was made to nine and concentrate the cassiterite commercially. The problem of a domestic tin industry and the question of the extent of the Alabama tin deposits have long been of public interest and concern. The deposits have been examined by numerous geologists and several governmental agencies, including the Geological Survey of Alabama, the Geological Survey and the Bureau of, Mines. of the Department of Interior, and others. The Bureau of Mines and the owners of the properties, Charles A. Dean and Robert A. Russell, investigated the Coosa County tin deposits under a cooperative agreement from October 1, 1948, to June 10, 1949. Sixteen hand trenches totaling 527 linear feet and 33 machine trenches totaling 6,780 linear feet were dug. Two shafts wore sunk for a total of 72 feet, and 44.4 feet of drifting was done. Thirty-one diamond-drill holes totaling 2,776 feet were drilled.. Four hundred thirty samples, representing 1,192.6 linear feet, were taken for assay and wore analyzed by the Southern Experiment Station at Tuscaloosa, Ala.

Jan 1, 1950

By Edward W. Parsons

The explosive-anchored rockbolt was field tested in six mines where rock conditions varied from incompetent shale or mudstone through fairly soft sand-stone to firm sandy shales. The purpose of the testing was to document, under a wide variety of conditions and in comparison to other rockbolt anchors, the quality of the anchorage produced by the explosive-anchored bolt. In addition, the length, strength, and design of the explosive charge necessary to produce positive anchorage up to the yield strength of the weakest component of the bolt were determined. A l4-inch length beaded explosive charge was found to be suitable, in general, in relatively weak strata, and the length can be reduced in more competent strata. Of the 127 explosive?-anchored bolts tested, 118 bolts produced an evaluated anchorage in excess of 17,000 pounds. Only 4 of 43 expansion-shell bolts and 4 of 14 wedge bolts produced anchorage this good. In preliminary tests, properly coupled explosive-anchored bolts did not ignite an explosive gas mixture. Some minor phases included in the investigation were as follows: (1) effect of explosive-anchored rockbolt on surrounding rock; (2) effect of time on anchored bolts based on torque tests; (3) effect of submersion in water on rockbolt anchorage; (4) pull tests to higher loads; and (5) ignition tests.

Jan 1, 1965