Search Documents

By R. A. Busch, R. R. Backer, R. W. McKibbin

The Bureau of Mines conducted laboratory tests to determine the slur- ry transport and deposition properties of coal waste. A 188.5-ft pipe test loop was constructed with instruments to measure density, flow, and power and discharge, suction, and differential pressures. A 20-ton sample of Western coal waste was crushed and screened to 100 pct minus 1/2 in. Eight loop tests using this graded waste were run at slurry densities ranging from 1.15 (25 wt-pct solids) to 1.46 (60 wt-pct sol- ids). The resultant friction-pressure gradients ranged from 0.06 to 0.24 ft of water per foot of 4-in standard steel pipe. Particle-size degradation was significant. In a typical loop test lasting 25 min, the minus 200-mesh fraction increased from 19 pct to 34 pct. Deposi- tion tests showed that without the use of a flocculant, the slurries would not dewater when left to stand for 1 week. With flocculant, ad- ditional water was released; however, the settled slurries remained thixotropic. Further testing is necessary to determine their suitabil- ity for use as backfill material in active mines.

Jan 1, 1965

By C. E. Brechtel

This project describes the design and testing of large face ventilation systems for oil shale mining. A design data base was generated by reviewing general industry practice, oil shale industry planning, and technical literature. Conceptual designs for seven different systems were developed and evaluated for suitability. A large, free-standing, jet fan and reversible fan with rigid duct were selected for fabrication and testing. The two systems were field tested in a dead-end heading 55 ft wide by 30 ft high and 320 ft long. System performance was optimized using measurements of air flow direction and air velocity. Total system performance was then measured using SF6 tracer gas released to simulate blast fumes, hot diesel exhaust, methane layering and methane from a blasted muckpile. Field testing indicated that both systems delivered similar performance. The jet fan offered some clear advantages because of its mobility, ease of oper-ation and lower power requirement. It also offered some functional advantages in ventilating for methane because of it high average velocity.

Jan 1, 1985

By Ann G. Kim

The U.S. Bureau of Mines applied its mine fire diagnostic method to an abandoned anthracite mine fire site in Carbondale, Lackawanna County, P A. The technique to locate fires in abandoned coal mines and coal refuse piles includes the determination of hydrocarbon concentrations in mine gases, the imposition of an underground gas flow direction, and use of a surface mapping method, to define heated and cold zones in underground coal strata. The heated zones at Carbondale were characterized by elevated methane concentrations. The results of 25 communication tests were analyzed to define 2 large (approximately 100 by 250 ft) and 5 small, isolated heated zones. An approximate correlation existed between the location of the heated zones and areas of anomalous snow melt. The correlation between the results of the diagnostic? test and subsurface temperatures was not significant.

Jan 1, 2010

By V. E. Homme

Low- and high-temperature reduction techniques were employed by the Bureau of Mines in study of conditions favorable to the formation of massive titanium crystals. '1,1,2 low-temperature method, feeding molten sodium to solidified titanium lower chloride-sodium chloride, produced higher quality and high quantity crystalline metal. The percentage of crystalline titanium was increased with increasing reactor diameter, melt depth, and titanium dichloride concentration. The high-temperature technique, feed molten sodium to melts above 8000 C, producing needle-type crystals of lower quality and with less consistent results than the low-temperature method. Layers of titanium foil, sponge, fine needles, wool, and crusts of sin-tered granules were formed during the earl, -art of the low-temperature reduction, and massive crystals were produced beneath this barrier in the latter part of the reduction. Crystalline titanium having an average hardness of Bhn 76 and representing 58 percent of the total titanium was obtained. Lamellar crystals up to 1 1/2 inches long with a hardness as low as Bhn 54 were also produced. A second-stage reduction for reclaiming titanium from offgrade sponge is described. Titanium produced by this method was comparable in quality to that from sodium reduction of titanium tetrachloride.

Jan 1, 1966

By P. M. Gruzensky

A survey of the literature has been made covering the extraction of bismuth from raw materials, its separation from lead, and its subsequent refining. The use of aqueous, nonaqueous, and fused electrolytes in electrolytic refining is reviewed. This literature survey has been prepared preliminary to some proposed investigations concerning the electrometallurgy of bismuth, and, although an effort has been made to cover a majority of the applicable references, a critical review was not attempted and no assertion is made that this manuscript is exhaustive in nature. Titles of publications in parenthesis are translations from the language in which the reference was originally published.

Jan 1, 1954

By M. J. Spendlove

A progress report is presented on a research program in which an attempt was made to develop a practical sulfide-volatilization process for recovering tin from low-grade Bolivian ores. Shaft-furnace designs and operating techniques were studied in a series of experiments in which the objective was to sulfidize cassiterite to stannous sulfide, remove the stannous sulfide by volatilization, reconvert the stannous sulfide to stannous oxide, and collect the resulting fume. A shaft furnace was developed and operated in a final test in which many of the previous difficulties were surmounted. Since the supporting funds were exhausted at this point, the project was discontinued; recommendations for further improvements in furnace design and operation were made on the basis of interpretation of experimental results obtained in shaft-furnace experiments and other related studies.

Jan 1, 1955

By Lloyd H. Banning

ELECTRIC smelting tests were conducted at the Northwest Electro-development Experiment Station, Albany, Oreg., to develop a feasible process for producing silicomanganese from siliceous manganiferous material. The Jackson County, Oreg., material used was massive and contained rhodonite as the most abundant mineral. Both raw and beneficiated materials were tested; various proportions and types of fluxes and reductants were used to make up the furnace charges. The silicomanganese product was used successfully in manufacturing various steels at industrial plants. The manganese content of the samples ranged from 23 to 28 percent; silica plus alumina content was as high as 55 percent-about four times the maximum specification for Metallurgical-grade ore. Sink-float laboratory tests indicated that the manganiferous material was amenable to beneficiation. Over 2 tons of rhodonite concentrate was prepared for smelting tests in a sink-float operation. Only the minus-3/4-inch, plus-8-mesh fraction was fed to a heavy-medium cone; over 97 percent of the manganese was recovered in the sink product, which contained 32.4 percent manganese and 44 percent silica plus alumina. About 25 percent of the silica was removed in the float product.

Jan 1, 1959

By William C. Smith

Roof support, an important aspect of ground control, involves maintaining roof competency to ensure a safe and efficient mining environment. Wide variability in rock quality and stress distributions requires a systematic approach to roof support design that satisfies specific goals. The success of past roof sup-port in reducing the incidence of roof falls has been primarily attributed to safer roof bolting practices. However, roof falls continue to be the number one occupational hazard in underground coal mines. This U.S. Bureau of Mines report presents a general overview of roof bolting and other roof support methods used in the United States. Characteristics of bad roof and associated roof failure theories are briefly presented as background to roof support. Methods of detecting and monitoring roof behavior and/or bolt performance provide essential feedback on roof support requirements. A discussion follows on roof bolt design that assimilates roof and support parameters into useful equations or nomographs to help decide what bolt types to use and how they should be installed under different roof conditions.

Jan 1, 1993

By Robert J. Evans

The Bureau of Mines is sponsoring a variety of long-term, high-risk research to advance state-of-the-art technology in U.S. underground coal mining. This report reviews the status of many Bureau projects that support fundamental underground coal mining operations; the project areas include cutting coal from the solid (extraction), hauling coal from the face (transport), and activities that sustain daily operations (logistics). Innovative equipment and technology have been developed, with these major objectives: to significantly improve coal mine productivity, to further advance coal recovery and personal safety within the mining industry, and to reduce the time needed to develop longwall panels. The majority of the prototype equipment covered in this report either has undergone or will undergo comprehensive evaluation at Bureau surface test facilities so that performance and reliability can be improved before the equipment is tested and evaluated in a working section underground.

Jan 1, 1988

By Sidney Katell

The reaction of coal, oil, or natural gas with air and oxygen and/or steam yields a gas containing varying amounts of impurities. Depending on the raw material and the end use of the product, these impurities include solids, such as dust or slag, and gases, such as hydrogen sulfide, carbon dioxide, and nitrogen. Considerable effort has been expended in developing and operating purification systems, and the literature is replete with equipment data and operating results. The research problems, the design, and the operation of the various systems have been the subjects of patent applications, journal articles, and textbooks.

Jan 1, 1959

By M. R. Geer

The use of the cyclone as a dense-medium cleaning device was first described by Driessen6/ in 1945, after development of the process in the Netherlands during the German occupation of World War II. A pilot plant was built in the Netherlands soon thereafter, and the first commercial plant was built in 1948. By 1958, 18 plants were operating or under construction.7/ Thus, economic factors in Europe, where the high cost of coal places a premium on efficient cleaning, dictated rapid adoption of the cyclone. American reception of the process differed. The Bureau of Mines presented the results of its own small-scale cyclone experiments in 1946;8/ showing a sharp separation between coal and impurity; adoption by industry now is taking place. There is now much greater emphasis on the efficient cleaning of fine coal, and the first American cyclone plant has begun operating; others are planned or under construction. With the present interest in improved treatment of fine coal, the Bureau of Mines felt that additional performance data on the cyclone would be helpful to industry. Therefore, a complete, open-circuit pilot plant was built to make cleaning trials on American coals covering a wide range of washability characteristics. Five raw coals and one middling product were included in the investigation, and each was cleaned at several densities; 17 cleaning trials are reported.

Jan 1, 1961

By D. J. Singleton

Erosion corrosion of 12 alloys in phosphoric acid waste water was studied by the Bureau of Mines. Tests were conducted on oblate spheroids or cylindrical specimens in 12-and 60-cm-diam ball mills by grinding phosphate rock in gypsum pond water with a starting pH of 1.6. For comparison, tests were conducted while grinding phosphate rock in plain water. Static corrosion tests in gypsum pond water also were conducted. For all alloys, the wear by erosion-corrosion (milling with gypsum pond water) was greater than the sum of erosion (milling with water) plus static corrosion. Erosion-corrosion wear was about 1,500 to 3,000 mpy for the alloyed white cast irons, 1,000 to 1,400 mpy for commercial steel ball material and type 316 stainless steel, and 600 to 900 mpy for nickel-base alloys and a high-manganese, nitrided stainless steel. Alloy costs per unit of phosphate rock 'processed favor a low-alloy, high-carbon steel or a high-manganese, nitrided stainless steel.

Jan 1, 1985

By Joseph Cervik, Gerald L. Finfinger

This Bureau of Mines publication reviews underground methane drainage pro- grams being conducted in various coalbeds. Equipment used in drainage programs such as drills, underground pipelines, and methane monitoring systems is described.

Jan 1, 1980

By M. Carrales

This Bureau of Mines publication presents short-range projections of domestic liquid hydrocarbon production through 1980. Appraisal of future crude oil production was made by evaluating the relationship between primary and enhanced oil recovery and the total crude oil producing trends in each of the oil-producing areas of the United States. Future natural gas liquid production was generally estimated by projecting historical production. Estimates of production were prepared for each of the oil producing areas and summarized for the Petroleum Administration for Defense (PAD) districts and total United States. From 1975 to 1980, crude oil production for the conterminous United States is expected to decline from 7.8 to 6.4 million barrels of oil per day (BOPD), and it is expected to increase from 8.0 to 8.2 million BOPD for the total United States. However, these estimates do not include additional production expected from the Elk Hills field in California and the Yates field in Texas. If included, 1980 production for the conterminous United States would be 6.7 million BOPD and 8.4 million BOPD for the total United States.

Jan 1, 1977

By Charles A. Kumbe

"INTRODUCTION The Sullivan Mine was examined by Thomas L. Chapman, an engineer of the Bureau of Mines, in March 1943. Samples taken from the few mineralized exposures justified further investigation of the property. To determine whether extensive exploration of the property would be warranted, the Bureau did a small amount of trenching and underground work during April 1943, 3/ under Bureau project 1462.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its, primary objective the, more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratary project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurigical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests.The investigations of the and Metallurgical Branches of the Bureau, as reported in this paper, were supervised by J. Hedges, district engineer for Arizona, and S. R. Zimmerly, regional engineer for the Western Region, respectively."

Feb 1, 1947

By Stephen M. Jasinski

The development and industry adaptation of advanced technologies have led to many important uses for bismuth and its compounds. Bismuth-base alloys are essential for manufacturing jet engine turbine blades, lenses, and various safety devices, such as fire-protection sprinklers. The addition of bismuth to iron, steel, and aluminum imparts properties to these metals that makes them useful in diversified applications. Bismuth is also used widely in medicine, pigments, and electronics. The United States relies heavily upon imports from South America and Europe to meet its demand for bismuth, which is recovered chiefly as a byproduct of lead processing.

Jan 1, 1992

By A. J. Kraemer

This report on the physical and chemical properties of typical crude oils of California is the 'eighth in a series on the producing districts of the United States. It includes discussion of results, tabulated data, and individual analyses of typical California crudes. Additional analyses of crude oils from the fields of Fresno, Kern, Los Angeles, Orange, end Ventura Counties will be published later in another Serial of the Bureau, but the summary tabulations are presented here. The samples represented in this report were collected over a rather wide interval of tine, the early samples having been obtained during the fall of 1919, and the most recent ones dating from the summer of 1923. It is thought that the samples are fairly representative, both of the older settled production and of the new flush production of the southern California fields.

Jan 1, 1924

By T. F. Curry, L. B. Berger, H. A. Watson, S. J. Pearce

The conduct of work at elevated air pressures , such as in caissons and in tunnel - driving in subaqueous strata , poses safety problems not encountered in mining and tunneling operations at ordinary atmospheric pressure . This publication discusses some of the problems involved and presents information on the following subjects : ( 1 ) Physiological effects of gases at elevated pressure . ( 2 ) Use of respiratory protective equipment in rescue or recovery operations in event of fire or other emergency in pressurized tunnels . ( 3 ) Effect of elevated pressure on performance of some gasdetecting instruments ; interpretation of the results . Various types of respiratory protective devices are discussed in relation to their possible use at elevated pressures , especially the 2 - hour , selfcontained , recirculating - oxygen - breathing apparatus , which has had wide use in the United States during rescue and recovery work in the mining industry . A modified procedure that eliminates the hazard of oxygen poisoning enabling the safe use of this apparatus at elevated pressures , up to 45 pounds per square inch , gage , and tests to verify its practicability are described . procedure involves control of the partial pressure of oxygen in the breathing

Jan 1, 1964

By H. P. Hermance

Preliminary examinations of the Parker and Webb deposits were made by E. E. Maillott, Bureau of Mines engineer in July 1942. The chemical and spectrographic analyses included in this report wore made at the Eastern Experiment Station of the Bureau of Mines at College Park, Md., under the general supervision successively of S. M. Shelton and of Paul M. Tyler, formerly regional engineer, Eastern Region. Beneficiation tests were conducted under the supervision of Frank D. Lamb. The mineral exploration was under the general supervision of J. D. Bardill, formerly district engineer. Acknowledgment is gratefully made to the St. Joseph Lead Co., in particular to John S. Brown and P. J. Mechin for their assistance. Special acknowledgment is made to the American Metal Co., Ltd., ,Ind to T. C. Moore for furnishing core-drill and assay data; to the Universal Exploration Co. and P. B. Jennings; and to the Northern New York Mining Corp. and C. H. Sprague for their permission to publish the core-drill dta. Excellent cooperation was given by Dr. W; M. Agar and C, L. Rogers of the Geological Survey.

Jan 1, 1949

By C. E. Jordan

The Bureau of Mines is conducting research into the pneumatic recovery of coarse mica and has used this method to produce mica concentrates that contain more than 90 percent mica. This research is being carried out pursuant to the Bureau's objective to develop technology that will help maintain an adequate supply of minerals and metals to meet national economic and strategic needs. Researchers used a Bureau-designed system of crushers, screens, and zig-zag air classifiers to concentrate coarse liberated mica particles from mica-bearing materials. This pneumatic system was used to concentrate four mica ores from Arizona, North Carolina, and South Dakota and three waste tailings from Alabama, Georgia, and South Dakota. Using these samples, it was demonstrated that plus 65-mesh size mica can be effectively recovered by the pneumatic method. Not only were the concentrates high in mica content; it was also demonstrated that this method can be used to recover up to 78 percent of the mica that was originally contained in the samples. Because it is a dry concentration method, the pneumatic beneficiation technique may be advantageous in areas where water resources are limited.

Jan 1, 1980