Search Documents

By Elger. G. W.

The Bureau of Mines investigated preheating of continuously fed, fragmented ferrous scrap charges by furnace offgases and utilizing substitutes for imported fluorspar to condition electric steelmaking slags. Three types of continuous scrap charging procedures were investigated to determine electrical energy consumption in a I-st (short ton) electric arc furnace. Cold and preheated scrap charges were continuously fed at rates averaging 37.5 and 43.7lb/min, respectively. The feed rate varied appreciably from test to test owing to hangup of the scrap in the charge bin. Approximately 7 pct less electrical energy was consumed in melting scrap preheated to 8400 to 1,1100 F by furnace off-gases than in melting cold scrap. Overall energy consumptions were 888 kW'h/st for cold scrap, 829 kW'h/st for preheated scrap" and 637 kW'h/st for conventional backcharged scrap. Stack gases from scrap preheating averaged 1200 F and a flow rate of 1,615 scfm compared with 2200 F and 1,302 sefm for cold-charged scrap. Slag conditioners tested included synthetic fluorspar, boric acid, hydroboracite, used aluminum potlining wastes and aluminum anode tailing wastes, and Sorelflux B. The boron-containing conditioners fluidized the slags the best, followed in order by the conditioners containing fluorine and titanium.

Jan 1, 1987

By Robert G. Bottge

The Bureau of Mines has engaged m a program to determine the availability of land for mineral exploration and development in Alaska. Land availability, based on ownership and Federal and State laws and policies, is compared with mineral terranes and mineral deposits. This is the fifth of six regional studies, which cover the State with a comprehensive set of maps and data compilations. This study covers an area of 112.3 million acres in western Alaska. In July 1986, 41.0 million acres, 37% of the study area, were available for mineral exploration and development; 14.6 million acres, 13%, were available with restrictions; and 56.7 million acres, 50%, were unavailable. Nearly 65% of the unavailable land is classified as national parks, preserves, wildlife refuges, and wild and scenic rivers. Of the 34.0 million acres of mineral terranes that underlie the study area, 12.9 million acres, 38%, are available for exploration and development; 3.6 million acres, 11%, are available with restrictions; and 17.5 million acres, 51%, are unavailable.

Jan 1, 1988

By G. L. Oldright

As sponge iron is much like porous, coarse sand, it is a tempting material to use in place of coarse scrap iron as a precipitant of metals, for scrap iron is relatively awkward to handle and exposes only a small amount of surface to pregnant solutions. The results of the experiments described in this bulletin are largely a record of the behavior of sponge iron as a precipitant of lead and copper under laboratory conditions comparable to those that would obtain in a commercial plant were it attempted to secure the maximum contact of surface between solution and precipitant. Physically, the study is largely one of the rates of diffusion of the metal ions in the solutions and through the metallic coatings surrounding the sponge iron particles. The practical objectives are to remove completely the valuable metals from solution and at the same time to obtain a precipitate of good grade. In order to fulfill this latter requirement, the precipitant should be almost completely consumed. These practical ends are usually secured by having the two substances involved pass each other counter-currently-that is, in such a manner as to have the strongest precipitant in contact with the most impoverished solution, and vice versa. EXPERIMENTS WITH LEAD SOLUTIONS In nearly all of the schemes involving the leaching of lead from its ores the metal has been put into solution as the chloride, and fairly concentrated liquors have been employed. The solubility of lead under such conditions is comparatively small at best; the hot pregnant liquors from which the metal is to be precipitated are then made nearly saturated with respect to lead, and only a very small amount of acid is used. Therefore it was not as necessary to learn the behavior of the sponge iron in precipitating lead from solutions of widely differing composition as to learn under what conditions, and with what mechanisms, this precipitation might be carried out most readily.

Jan 1, 1928

By W. W. Adams, T. D. Lawrence, D. R. White

"This paper presents the results of the eleventh yearly accident-prevention contest, the National Safety Competition of 1935, conducted by the United States Bureau of Mines. Participating in the competition were 336 mines and Quarries in 37 States. Five mining or quarrying companies, each the leader in its group for having established the best safety record during the year, were awarded the national safety trophies 'Sentinels of Safety.Since these annual contests were begun 11 years ago the scope of the competition has been broadened materially, both as to the number of plants participating and as to the number of man-hours of exposure to accident hazards. Moreover, marked progress in the pre¬vention of accidents has been achieved, as is indicated by an almost constant downward course in the accident-frequency rates for the contest group as a whole during the past 11 years. On the other hand, the accident-severity rates for the group showed an upward trend during the first part of the period and a downward trend during the latter part, except in 1930 and 1934, when two disastrous explosions occurred with heavy loss of life, and in 1935, when there was an increase in the number of fatalities although no major disasters occurred. The accident rate for 1935, both as to frequency and severity, was higher than for 1934.The National Safety Competition is conducted by the Bureau of Mines in the interest of safety in the mining and quarrying industries. This object is accomplished directly through the efforts of the competing companies and their employees to win first place in the competition and thereupon receive well-merited and national recognition for their achievement. Indirectly the purpose of the contest is accomplished through studies by the Bureau of Mines of the fasts contained in the accident reports which the competing companies furnish to enable the Bureau to compute the accident rates that are the basis for determining the winners of the contest.The statistics that constitute the basis for determining the winning companies and the relative standing of all companies are prepared uniformly without regard to the States in which the companies operate, or to differences in classes of accidents covered by State laws relating to compensation for injuries resulting from industrial accidents."

Jul 1, 1936

By Donald S. Colby

This Bureau of Mines report is essentially a handbook, or manual, for making the type of mineral resource valuation commonly required for such public policy problems as mineral leasing. The principle of resource valuation through the capitalization of cash flow is well established. A mathematical procedure, based on a simplified accounting system, is detailed for calculating cash flow from revenue, plant costs, and operating expense. Variations of procedure cover cost depletion, percentage depletion, and depletion limited to 50 percent of net income. The influence of the depletion provisions of the tax regulations on the value of a resource to an owner and to an operator is analyzed. The relationship of royalty, bonus payments, and sales price to resource value is also described, and methods for approximating resource values using these payments as input data are developed.

Jan 1, 1969

By Carl W. Kelley

PRODUCTION in the United States of carbon black has increased from 20 million pounds per year in 1920 to over 2 billion pounds in 1964 valued at $156 million, mostly for consumption by the rubber-tire industry, which uses over 90 percent of total production. Production of over 2 billion pounds in 1964 is a 7.8-percent increase over 1963 and is the first time furnace black production has topped 2 billion pounds. Although 1964 channel black production dropped 6 percent below 1963, carbon black produced by the furnace process, which ac-counted for 92 percent of total production, increased 9 percent to 2,053 million pounds. Total shipments during 1964 amounted to 2,245 mil-lion pounds, a 7 percent increase. This growth parallels the expansion of the automotive and petroleum industries. Along with this expansion have been many advances, both in methods of manufacture and in the quality and variety of blacks available to industry. There are several kinds of carbon black, thermal, channel, furnace, lamp, and oil blacks. Until recently, channel has been the important black in rubber compounding. Following the introduction of the synthetic GR-S, and more recently of "cold rubber," it has been found that certain furnace blacks with particle size larger than that of the standard channel black give superior reinforcement. A great advantage of furnace black is that its yield per unit of gas feedstock is higher than that of channel black. The 184-million-pound increase in domestic carbon black sales was partially offset by a 37-million-pound decrease in exports. Decrease in exports especially to Europe, is expected to continue. In Europe, as in the United States, the major end use for carbon black is in the manufacture of automobile and truck tires. Although the number of automobiles in Europe is predicted to grow by about 7.5 percent per year, compounded until 1975, the increased demand will be met by a 20 percent increase in existing capacity and by the new plants being built in Europe by U.S. companies. Also) aromatic oils for producing furnace blacks are plentiful now that western Europe's chemical industry is switching to a petroleum base.

Jan 1, 1965

By William C. McBee

Specialized sulfur concretes were developed by the Federal Bureau of Mines as a result of research for the beneficial utilization of sulfur in construction materials. Materials were developed for use in acid and salt corrosive environments where portland cement concrete has been found to deteriorate. Because the mineral aggregates also come into contact with the corrosive media, concretes were developed utilizing both limestone and quartz aggregates. The sulfur binder used with both aggregates was modified by reaction with 5 pct dicyclopentadiene to improve product durability. Sulfur quartz aggregate concrete was found to have moderately high strength characteristics (6,000 psi compressive) and was extremely resistant to chemical attack by both acid and salt solutions. Sulfur limestone aggregate concrete exhibited very high strength characteristics (9,000 psi compressive) and was extremely resistant to chemical attack of salt solutions. Both types of concretes maintained their strength and integrity after long-term testing in acid and salt solutions and exhibited considerable resistance to damage by the action of freezing and thawing. Potential uses include leach tanks, electrolytic cells, thickeners, bridge decking, industrial flooring, pipe, and tile.

Jan 1, 1979

By J. A. McAllister, H. G. Iverson, K. C. Dean

"INTRODUCTION During the course of the investigation of the occurrence of manganese deposits in the western United States, laboratory studies of concentration were conducted at the Salt Lake City station on a sample of ore from the Lake Valley mines of the Newalpitt Fluorspar Corp. of Deming, N. Mex. The ore was reported to be representative of the type that would be mined for mill feed. The sample tested was found to be amenable to beneficiation by ore-dressing methods for the production of products that, when sintered, assayed over 44 percent Mn.At the beginning of the investigation of manganese-ore beneficiation in December 1940, the only product marketable to Metals Reserve Company was ferrograde manganese grade B, the requirements for which follow: Mn, min., 48 percent; Fe, max., 7 percent; Si02, max., 10 percent; P, max., 0.18 percent; Al203, max., 6 percent; Zn, max., 1 percent, Al2O3,Later the specifications were modified gradually. As of May 15, 1943, manganese products were acceptable if they contained over 35 percent manganese and less than 3 percent zinc and 1 percent phosphorus. Prices were based upon material containing 48 percent manganese, 6.0 percent iron, and 11 percent silica plus alumina. Premiums were paid for manganese content in excess of 48 percent and iron content below 6 percent, penalties being imposed upon products containing less than 43 percent -manganese, or more than 6 percent iron, or more than 11 percent silica plus alumina. The specifications for commercial manganese further required that maximum particle size be 12 inches and that, 75 percent of the product be coarser than 20-mesh. Therefore, fine material such as table and flotation concentrates had to be nodulized or sintered. In addition, oarbcnate manganese ores were not acceptable unless calcined."

Feb 1, 1948

By R. T. MacMillan

A number of chemical techniques have been applied to manganese ores from three areas of Aroostook County, Maine. Although large tonnages of these ores have been proved, they are low grade, and their exploitation has awaited a suitable beneficiation scheme. As conventional ore-dressing methods had failed to yield satisfactory results, attention was turned to chemical procedures. Leaching with dilute (7-percent) H2S04 extracted over 90 percent of the manganese from ore of the Dudley farm area, consuming 3.8 pounds of acid per pound of manganese extracted. Ores from the Littleton Ridge and Maple Mountain-Hovey Mountain areas were less amenable to this treatment, yielding approximately 80 and 60 percent of their Mn content, respectively. To increase the percentage extraction of manganese in the latter two ores, a number of factors were varied, including (1) acid concentration in the extracting solution, (2) ratio of acid to Mn in the slurry, and (3) preliminary heat treatment of the ore with a reducing agent. Other acids, including HNO3, HC1, and H2SO3, were tried also; however, no significant improvements in the Mn leached from Maple Mountain-Hovey Mountain ore were made. The manganese extraction of Littleton Ridge ore was raised to 90 percent by providing 9 to 11 pounds of HNO3 per pound of Mn in the ore.

Jan 1, 1954

By R. V. Ramani

In this report, the application of the Open Pit Materials Handling Simulator (OPMHS) to a mine located in Ohio using a large stripping dragline, and truck and front-end loader (FEL) is described. The specific objective of the study is to demonstrate the application of the simulator to mine planning and coal production. On the basis of the simulations, it was concluded that the production from the haulback operation should be increased to accommodate improvements in both the stripping dragline's availability and mean cycle time. Several alternatives were studied for the best use of equipment if the present operating parameters could not be improved upon. No economic analysis of these proposals were made.

Jan 1, 1977

A major highlight of Fiscal Year 1993 is the completion of a new research facility dedicated to the advancement of robotics research and development. This new facility brings to the U.S. Bureau of Mines one of the largest and most unique facilities of its kind in the world. Located at the Bureau's Pittsburgh Research Center, the facility consolidates under one roof, all of the resource requirements of a first class automation and robotics research program. The Mining Robotics Development Center (MRDC) is the result of a major renovation of a large under-utilized warehouse-type structure and brings together the laboratories and offices previously housed in five separate buildings scattered throughout the Pittsburgh Research Center's 238-acre site. This new facility will support the computer-assisted mining research program, a high priority, multi-million dollar program that is expected to have a high impact on the health and safety of miners and coal productivity.

Jan 1, 1993

By Leonard Obert

THIS REPORT presents methods and principles useful in designing underground mine openings and pillars in competent rock formations. Two types of formations are considered: (1) Massive formations, in which openings are generally mined with an arched roof, and (2) bedded formations, in which openings are generally mined with a flat roof. Design principles for openings and pillars in massive formations are obtained by considering the maximum tangential stresses developed around single and multiple openings for stress fields of various types. Design principles for openings and pillars in bedded formations are obtained by considering the average stress in pillars and the maximum stresses in roof layers. Experimental procedures for making stress, strain, and in situ physical-property measurements in underground mines to check design calculations are outlined and the results discussed.

Jan 1, 1960

By B. J. Moore

This publication contains routine analyses and related source data for 374 natural gas samples from 24 States and 5 foreign countries. These samples were collected during calendar year 1966 as a part of a continuous survey of the free world for occurrences of helium in natural gas. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses of foreign samples contained in this publication represent the first samples received as a result of this expanded program. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4 Eight previous publications have been made to present the results of 7,244 gas analyses made? by the Bureau of Mines Helium Activity prior to 1966. The first three, Bulletins 486,5 576,6 and 617,7 contain analyses and related

Jan 1, 1967

By W. A. Grosh

The Piquette Mining and Milling Co, operates a zinc mine and concentrating mill in the Upper Mississippi Valley zinc-lead district near Tennyson, Wis. The principal ore mineral is zinc sulfide, which occurs in limestones and dolomites of the Decorah formation. Exploration in the district is by churn drilling from the surface. An adit at the base of the ore zone provides access to the mine. A room-and- pillar mining method with irregular pillars is used. Drilling is done with Jumbo-mounted drills. The broken ore is loaded by crawler-mounted front-end loaders into diesel-powered trucks for haulage direct to the mill.

Jan 1, 1959

By Lloyd R. Michels, Burke Cartwright, S. F. Ravitz

"INTRODUCTION Frequent attempts have be,made in the electrolysis of molten magnesium chloride to regenerate the electrolyte by allowing the chlorice generated at the anwdo to read with magnesium oxide and carbon within the melt according to the following reactions: (1) MgO + C + CL2 = MgCl2 + CO,(2) 2MgO + C + 2C12 = 2MgC12. + CO2.The principal advantages of such a procedure are that (1) the direct source of magnesium is magnesium oxide rather than the more expensive dehydrated magnesium chloride and (2) it is not necessary to handle or dispose of large quantities of chlorine or hydogen chloride.Grätzll 5/ proposed the use of an MgO carbon feed in a more or,less compact form in the anode compartment, of the cell. In a patent issued to Magall Aktiengecellschaft, 6/ a compact mixture of MgO and carbon is used as the anode itself. Kato 7/ and Backer 8/ add the feed in finely divided form to the surface of the anode compartment. The Bureau of Mines 2/ recently made a pilot-plant investigation of the electrolysis of suspension of MgO and carbon from chloride melts, in which it was found that although,current efficiencies of 60 to 70 percent were obtainable, the formation of sludges containing MgO, carbon, and magnesium seriously interfered with the operation of the cell,"

Apr 1, 1945

By William W. Aljoe

The hydrologic characteristics of two abandoned underground coal mine sites, near Latrobe, PA, and Uniontown, PA, were investigated by the U.S. Bureau of Mines for possible implementation of alkaline injection into the mine pools as a means of abating their acid discharges. The Latrobe site was chosen for a one-time application of alkaline injection to achieve a partial, short-term neutralization of a limited portion of the mine pool. A quantity of alkaline reagent (sodium hydroxide) sufficient for a one-time neutralization of the water in this portion of the pool was added. Although nearly all of the neutralizing reagent had moved away from the injection wells within 6 weeks, no evidence of neutralization was noted at the mine discharge during the study period. This lack of neutralization probably occurred because the injection wells did not intercept a primary flow path through the mine. Criteria for successful application of alkaline injection at this or other sites include (1) positive identification of the primary flow paths through the mine pool and (2) addition of quantities of alkaline reagent sufficient to neutralize the entire volume of the pool along the primary flow path.

Jan 1, 2010

By James F. O?Neil

Brown iron ore deposits in Quitman County, Ga., were investigated by the Federal Bureau of Mines in cooperation with the State of Georgia, Department of Commerce, and the University of Alabama. Ninety-one holes were drilled, having an aggregate footage of 2,188 feet; seventy-one holes penetrated 248 feet of iron mineralization. Average thickness of the ore zone was 3.5 feet under an average thickness of 14.7 feet of overburden. The drilling developed inferred reserves containing nearly 30 million long tons of crude ore with an average analysis of 28 percent iron plus minor quantities of manganese. Test work done by the Bureau on the crude ore samples indicated that they would upgrade by current lug washer practice, with the use of a 1i8-inch screen, and yield 4.4 million dry long tons of concentrate with an average analysis of 52.1 percent iron plus manganese. The weight recovery obtained was 14.7 percent. Research studies made by the Bureau showed that the weight recovery would be increased by changing the screen size without any appreciable sacrifice of grade. The average weight recovery was increased to 18 percent with a 10-mesh screen and 22.8 percent with a 20-mesh screen. Screen tests studies indicated that there was no appreciable interlocking of the iron and manganese minerals and the clay and silica waste particles of the materials retained on a 200-mesh screen. Clay was prominent in micron-size slimes. Silica was deleterious in the minus 20-mesh size.

Jan 1, 1965

By E. S. Leaver

The mineral value in the ores from the Mother Lode mining districts of California is almost entirely gold, Although many mines have produced extremely high-grade ore the usual mill grade averages approximately $7.00 gold per ton. Fully 80 per cent of the gold has been and is now being recovered by amalgamation. Various methods have been introduced to recover the gold that was not obtained by the amalgamation processes. They include vari¬ous kinds of gravity concentration which in some cases were followed by chlorination or cyanidation. The usual practice includes only stamp battery, plate-amalgamation, and vanner concentration. In the very early practice the tails were run to waste through the main drainage streams of the different mining districts. During later years very large storage dumps have been impounded. These old tails, together with those being saved from present mills, furnish the problem discussed in this article. The clean sand portion of these mill tails is amenable to the usual cyanidation. The slime portion contains the major amount of the gold lost, but it also contains 1-1/2 to 3 per cent carbon, which precludes direct cyanidation of this part of these low-grade waste tails. The black carbonaceous slime portion is the particular problem considered in this report.

Jan 1, 1930

By C. P. Bowie

For years many oil producers have believed that often low-pressure oil- and gas-bearing strata have been over coked in fields where the rotary system of drilling has been used. Collom3/ gave as a reason for this condition that because the mud fluid was thick, the oil or gas stratum was plastered and sealed as the tools passed through it and no oil showed at the surface. Although this observation was made 15 years ago, it may often still be true notwithstanding modern developments in coring and electrical logging. Operators have believed, also, that mud fluid does not solidify behind the casing. Lewis and McMurray4/ stated: "All the evidence obtainable from practical experience points to the fact that the mud fluid properly mixed and employed does not solidify behind the casing, even in deer wells and after long periods."

Jan 1, 1937

6784. Barnes, V. L., and Romberg, Frederick. Gravity and Magnetic Observations on Iron Mountain Magnetite Deposit, Llano County, Tex. Geophysics, Menasha, Wis., vol. 8, No. 1, 1943, pp. 32-45. An outcrop of magnetite in the Central Mineral region of Texas is explored experimentally with a dip needle and a gravity meter. Two anomalies are observed, one due to the outcropping body and one probably due to a previously unknown body close to the outcrop. The possible attitudes of the bodies are discussed, and their masses and probable dimensions are computed from the gravitational observations. - Author's abstract.

Jan 1, 1943