Search Documents

By Frank E. Cash

Although during the past 10 years Alabama has attained an enviable position by its coal-mine accident experience and, like most of the other coal-mining States, has made progress in the safer operation of coal mines, there is still room for improvement, which can be realized only by still greater efforts on the part of employees and employers. From 1993, when accidents were first recorded by the Alabama State Mine Inspection Department, to 1934, inclusive, 3,451 men lost their lives in the production of 569,722,676 tons of coal. The primary purpose of this report is to bring to the attention of the mining industry in Alabama end elsewhere statistics of fatal accidents for 1931-34, with the hope that a study of the causes may lead to reduction of similar accidents in the future.

Jan 1, 1936

By Maria I. De Rosa

Table 46 and figure 16 show the number of fires and fire injuries for metal/nonmetal mills by state during 1990-2001. Table 46 also shows the injury risk rates, employees' working hours, and lost workdays. In all, 77 fires occurred in 26 states. Thirty-seven of the fires caused 41 injuries and 1 fatality (including 5 fires and 3 injuries involving contractors). The yearly average was 6.4 fires and 3.4 injuries. Fifty-four fires with 26 injuries and 1 fatality occurred at metal mills; 23 fires with 15 injuries occurred at nonmetal mills. The Ewhr value was 845 x 106 hr (Irr = 0.01), and the LWD value was 6,681. Minnesota had the most fires (16 fires and 5 injuries), followed by Arizona (9 fires and 3 injuries), Wyoming (8 fires and 3 injuries), Nevada (7 fires, 4 injuries, and 1 fatality), and Texas (4 fires and 7 injuries). Of these states, Texas had the highest injury risk rate value (Irr = 0.033). Table 47, partly illustrated in figure 17, shows the number of fires, fire injuries, fire fatalities, risk rates, employees' working hours, and lost workdays by time period. The number of fires increased slightly during the second period, then decreased during the remaining periods. The number of fire injuries show a decrease during most of the periods (an increase is seen during the third period), accompanied by a decline in employees' working hours during most of the periods. The Irr values follow patterns similar to those shown by the injury values. Tables 48-53 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 18 shows the major variables related to fires for 1990-2001. Table 54 shows the number of fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By Jr. Denton

This U.S. Bureau of Mines report presents the documentation for HEAPREC, a methodology for calculating reclamation performance bonds for cyanide heap leach operations. HEAPREC is a template developed for use with Lotus 1-2-33 release 2.01 or newer software. The report is presented in step-by-step "user's manual" format. Appendices contain detailed background and reference material on performance bonding, cyanide detoxification regulation, cyanide detoxification methods, general mine reclamation procedures, and an example bond calculation.

Jan 1, 1992

By James W. Reil

A test series of small, precisely-controlled and thoroughly-monitored production blasts was conducted at two quarries. In each series, all variables except delay were kept constant, as much as practically possible. The first aim of the study was to determine the effect of local geology on ground vibration. The second aim was to test several hypotheses relating the effect of millisecond delay intervals to fragmentation and ground vibration. A resonant frequency of ground vibration was shown to be related to the thickness of the overburden, in accord with a model proposed by Gupta (1961). Since the overburden geology creating this resonant vibration cannot usually be changed, two methods were tested to choose delays such that blast vibrations would destructively interfere. These were shown to be effective in modifying both the peak particle velocity and response spectra of ground vibration. The delay interval chosen also affects fragmentation, primarily in massive rock, with an optimum relief between holes of 2 ms/ft. Strain gage records indicate a possible mechanism consistent with this information.

Jan 1, 1985

By T. A. Klinefelter

ONE OF THE many services rendered by the Federal Bureau of Mines is the identification and general examination of ore and mineral samples. Many of these, coming from almost every State in the Union, are clay and shale samples. Other Government agencies, State geologists, universities, and other laboratories are often requested to make similar examinations. This publication describes methods of testing these samples. An earlier paper, published in 1943, described Bureau of Mines methods of testing such clays.3 This paper was to be followed later with another (part II) that would describe much more thorough testing than did the rather general outline of part I. Part I has been out of print for some time and needs revision, and part II was never written; hence, the present publication is designed to include part I and also those additions intended as part II. The tests presented in part I were simple, requiring only the ordinary equipment to be found in any good chemical laboratory. The second publication was to include a greater number of test procedures and information on increasing the accuracy and precision of those previously given.

Jan 1, 1957

By L. Y. Sadler

This report summarizes the findings of a 9-yr research program, sponsored by the U.S. Department of Energy and conducted by the Bureau of Mines, to evaluate refractory liner materials for coal gasifier reactors. Commercially available refractories were exposed to coal gasifier reactor environments, reproduced in the laboratory with a high-temperature, high-pressure test facility, followed by extensive postexposure evaluation. Thirty-six castable or gunnable refractories and cements and 24 refractory brick were evaluated. The behavior of castable refractories reinforced with stainless steel fibers was also examined. Gas environments that were evaluated included steam, H2, CO2, CO, and typical high-and low-Btu gas mixtures. Exposure pressures ranged from 100 to 1,000 psig, temperatures from 5000 to 1,1000 C, for periods from 50 h to 2,000 h. In some exposures, sodium and/or potassium hydroxide were introduced in order to simulate a high-alkali environment. It was found that intermediate-and low-alumina refractories produced from domestically available raw materials, rather than high-alumina refractories produced from imported raw materials, gave the best service as liner materials and that alkali attack was probably not a serious problem with most refractories. Based on the results of this program, good choices of refractory liner materials for gasifier reactors can be made.

Jan 1, 1984

By C. W. Davis

This report follows the same general scheme as did its predecessors; it begins with a dissertation on some phase of ore-testing, continues with results of investigations of ore-treatment methods and of metallurgically important analytical processes, and concludes with an exposition of tests made by established methods on typical ores selected as representative of certain mining districts. One of the first things that is done after an ore has been received is to look at it under the microscope. Microscopic examination serves as an important complement to chemical analysis in interpreting the percentage composition in terms of minerals. If it has been found difficult to treat an ore, the reasons for this action and indicated methods to overcome the difficulties may be ascertained by testing with a microscope. For example, failures in selective flotation have been traced to intimate mineral association and changes in mineral surfaces through incipient oxidation. The importance of surface stains or tarnishes and the presence of adhering slime particles have been found to be responsible for the difficulty experienced in the treatment of certain gold ores.

Jan 1, 1938

By C. W. Davis

This report follows the same general scheme as did its predecessors; it begins with a dissertation on some phase of ore-testing, continues with results of investigations of ore-treatment methods and of metallurgically important analytical processes, and concludes with an exposition of tests made by established methods on typical ores selected as representative of certain mining districts. One of the first things that is done after an ore has been received is to look at it under the microscope. Microscopic examination serves as an important complement to chemical analysis in interpreting the percentage composition in terms of minerals. If it has been found difficult to treat an ore, the reasons for this action and indicated methods to overcome the difficulties may be ascertainedd by testing with a microscope. For example, failures in selective flotation have been traced to intimate mineral association and changes in mineral surfaces through incipient oxidation. The importance of surface stains or tarnishes and the presence of adhering slime particles have been found to be responsible for the difficulty experienced in the treatment of certain gold ores.

Jan 1, 1938

By D. J. MacDonald

The Bureau of Mines has conducted bench-scale investigations leading to the design of an integrated process for producing reactor-grade zir-conium oxide (Zr02) from zircon sand, which avoids the air pollution, water pollution, fire hazard, and odor problems associated with the hexone-thiocyanate process. The integrated process consists of three steps: production of crude zirconyl sulfate solution, solvent extraction, and production of Zr02 from strip liquor. This report describes the solvent extraction step. Multistage, countercurrent liquid-liquid extraction with a tertiary amine in kerosine was used to separate zirconium from a dilute H2S04 solution containing hafnium and other impurities. Process steps de-scribed include extraction from an aqueous feed solution to form a hafnium-contaminated, zirconium-bearing organic-phase solution, scrubbing to separate zirconium from coextracted hafnium, stripping to transfer hafnium-free zirconium into an aqueous strip liquor, chloride-loading to produce a chloride-bearing organic solution, scrubbing with the chloride-loaded organic solution to remove traces of uranium impur-ity from the zirconium-bearing strip liquor, and regeneration to pre-pare the organic solution for reuse. These steps were performed simul-taneously in steady-state, bench-scale experiments. Zirconium recovery of up to 93 pct was achieved. Results of an economic evaluation are included.

Jan 1, 1984

By F. A. Penning

A number of highly instrumented free fall tests were performed on an arrestment system for a man cage in a vertical shaft. Tests were conducted in the U.S. Bureau of Mines free fall test tower at the Colorado School of Mines. A single tooth safety dog was used to stop on 4x6-in. Keruing (Phillipine mahogany) wet and dry wood guides. The safety dog had a penetration depth of 1 in., an adjustable width from 1-1/2 to 2-1/4 in., and a tooth angle of 80 deg. Twenty-seven free fall tests were performed covering a range in weights from 3-1/2 to 10-1/2 tons, hoisting velocities from 850 to 1350 feet per minute. Average g loads were measured from a low of 0.6 to a high of 3.4. The electronic instrumentation included piezoelectric and seismic mass accelerometers, strain gages on structural and mechanical elements, load cells in the guides, and distance measuring. Computer analysis was used to correlate with experimental measurements used to calculate stress. A statistical analysis gave no indication that the velocity or area affected the wood crushing stress. The instrumentation revealed a chatter occurring during the stop as shown by the accelerometers, strain gages, and load cells. Additional work is required to analyze this newly discovered phenomenon. The chatter imposes loads much higher than the average g load.

Jan 1, 1980

By B. J. Moore

This publication contains routine analyses and related source data for 547 natural gas samples from 22 States and three foreign countries. Of this total, 340 samples were collected during calendar year 1967. The remaining 207 analyses are of samples collected during previous years, but releases granting, permission to publish the results were not received until 1967. All samples were collected as a part of a continuous survey of the free world for occurrences of helium in natural gas. The Bureau of Mines has conducted this survey in the United States since 1917, and in 1965 it was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus which are described in Bureau of Mines Bulletins 4863 and 516.4 Nine previous publications have been made to present results of 7,618 gas analyses made by the Bureau of Mines Helium Activity prior to 1967. The first three, Bulletins 486,5 576,6 and 6177 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960. The other six

Jan 1, 1968

In 2006, a total of 2,113 coal mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Coal mines comprised 14.2% of all mining operations. ? Bituminous mines comprised 92.5% (n=1,955) and anthracite mines 7.5% (n=158) of coal mining operations. ? Approximately 71.0% of all coal mines were located in three states: Kentucky (29.2%), West Virginia (21.8%), and Pennsylvania (20.3%).

Jan 1, 2008

By H. D. Raymond

This report contains a summary of designs, specifications, costs, and schedules developed for a prototype oil-shale demonstration mining program to be undertaken at the Horse Draw site in the Piceance Creek Basin, Rio Blanco County, Colorado. The objective of the demonstration program is to assess the feasibility of extracting oil shale and associated saline minerals from deep, rich oil shale zones which occur within the central portion of the Basin. Four mining systems were specified for demonstration. These include (1) chamber and pillar mining with backfill; (2) sublevel stoping with backfill; (3) sublevel stoping with full subsidence; and (4) block caving. Commercial-scale designs for each system were modified and scaled down as required to achieve program objectives. The demonstration mine layout and design includes specifications for ore handling, backfilling, ventilation, dewatering, maintenance, and supply systems. A feature of particular interest in the design is the combination of block caving and sublevel stoping methods into a single unit for demonstration of subsidence mining systems in deep oil shale deposits. The report also contains a detailed breakdown of projected capital and operating costs for the demonstration mining program.

Jan 1, 1979

By F. R. Cattoir

This Bureau of Mines study investigated molten salt electrorefining for beneficiating low-grade, high-carbon ferrochromium products which can be readily produced from domestic chromite concentrates. A second objective was to refine commercial ferrochromium into low-iron chromium products. Electrorefining of both types of ferrochromium in molten CaC12-NaCl-CrC12, CaCl2-MgC12-CrCl2, or KC1-LiCl-CrCl2 electrolytes produced chromium-iron products with virtual elimination of other impurity elements and some lowering of the iron content, Over 90 percent of the chromium present in the feed materials was recovered. The electrodeposited products were upgraded further by magnetic separation techniques into chromium containing less than 5 percent iron. The technical feasibility of preparing a premium chromium product from a low-grade, high-carbon ferrochromium made from domestic chromite was demonstrated. Chromium virtually free of carbon, oxygen, and silicon from high-carbon ferrochromiums was produced. In addition, the amenability of three commercial grades of ferrochromium to electrorefining and magnetic separation for preparing chromium metal containing less than 5 percent iron was determined.

Jan 1, 1969

By A. L. Worthen

This is one of a series of pacers being published by the United States Bureau of Mines, describing mining and milling methods at crushed-stone plants throughout the United States. These pacers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total production costs. Although the publication of total production cost might not be advisable in some instances, yet a knowledge of operating costs is essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called o this differentiation in order that there will be no misunderstanding of the scope of the cost tabulations. This paper deals with the quarrying and crushing methods used at the Plainville plant of the New Haven Trap Rock Co., which produces annually between 275,000 and 300,000 tons of trap rock, Although pct the largest quarry operated by the company, it typifies the standard methods used by all the quarries in producing crushed stone and has one or two rather unique operating features. The cost of production at this plant is close to the average cost at all quarries of the company.

Jan 1, 1936

By F. Albayrak

This report is a study of the impact of Federal laws and regulations on the domestic supply of metallic and nonmetallic minerals. The study was confined to pertinent environmental legislation and the recently enacted Federal Mine Safety and Health Act of 1977. Emphasized were the legal requirements placed on individual selected mineral industries, and the economic impact of these requirements. A certain amount of attention was also directed to the particular environmental and health and safety problems generated by selected mineral industries. The study also pinpointed a list of major problem areas having significant impact on the domestic mineral supply.

Jan 1, 1978

By Lloyd A. Morley

This Bureau of Mines publication presents a comprehensive review of mine electrical power-system theory and practice. It discusses fundamental theory and the vital aspects to be considered in planning and designing mine electrical power systems. The report is divided into three major sections. The first presents the history of electricity in mining and the fundamentals of electrical phenomena and components. The second focuses on power-system components: motors, grounding systems, cables, and protective equipment and devices. The final section includes mine power-center equipment, switchhouses and substations, batteries, and mine maintenance.

Jan 1, 2003

By R. E. Mussier

This investigation was made to study new methods to prepare high-purity yttrium metal, Various methods were used to prepare pure intermediate compounds, primarily chlorides, bromides, and iodides, which were subsequently reduced to metal. The process found most suitable for the preparation of pure anhydrous yttrium chloride involved thermal dehydration of a mixture of hydrated yttrium chloride and ammonium chloride while under vacuum. Yttrium bromide and iodide were prepared most effectively by the direct halogenation of yttrim carbide. Yttrim carbide was obtained by reacting and melting yttrium oxide-carbon mixtures in a carbon-arc furnace. Yttrium halides were purified by vacuum distillation and reduced by alkali or alkaline-earth metals. Lithium and sodium proved to be the best reductants from the standpoint of yield (>95 pct) and purity (>99.8 pct) of the yttrium. The product of the reduction step was sponge metal, which was consolidated readily by conventional cold-mold, arc-melting procedure. The purest yttrium obtained in laboratory scale work was prepared by sodium reduction of yttrium chloride and contained only 125 pp oxygen; other impurities did not exceed 1,000 ppm. In larger scale tests yttrium containing only 800 to 1,000 ppm total impurities was obtained by lithium reduction of yttrium chloride. The tensile properties of high-purity yttrium were determined. Mechanical tests showed that yttrium can be forged, extruded, rolled, spot welded, and deep drawn.

Jan 1, 1963

By M. L. Whisman

The Bureau of Mines developed and tested in the laboratory several innovative techniques for reclaiming used lubricating oil. These processes included percolation through both chemically treated clay and ion-exchange resins, distillation through batch and continuous wiped-wall vacuum apparatus, treatment with solvent extraction systems, and chemical removal of impurities with chelating agents. In each treatment, the criteria of evaluation was oil recovery and reduction of acidic and metallic components. Both vacuum distillation and solvent treatment ranked high in their abilities to remove acidic and metallic components of the used oil with good oil recoveries. A combination of the two techniques gave the best overall results in terms of quality evaluations made by established bench tests. The methods were not ranked according to economic practicablity.

Jan 1, 1974

By William L. Crentz

In a Nation-wide appraisal of coking-coal reserves and of the practicability of upgrading marginal deposits to metallurgical standards, this study of the preparation characteristics of the coals in Cambria County, Pa. , was undertaken. Over 90 percent of the coal remaining in Cambria Comity is found in the Upper Freeport, Lower Freeport, Upper Kittanning, and Lower Kittanning beds. The Middle Kittanning bed, although mined on a commercial scale in the past, is not an important bed now, as most of the remaining reserves are too thin to be mined over wide areas. For many years, Cambria County has been an important source of coal for industrial and metallurgical purposes. The) principal production comes from the Lower Kittanning bed, which accounts for almost .60 percent of the Cambria County coal output. Table 1 shows the county's coal production, by beds, during 1948.

Jan 1, 1950