Search Documents

By Thomas M. Barczak, Dennis R. Dolinar, Gabriel S. Esterhuizen

Longwall mines typically use some form of standing support for secondary roof support in longwall tailgate entries. Although there have been several new support products developed for this application, there remains no universal design criteria to optimize the application of these support technologies. The requirement for optimization and proper support selection is to understand the degree of control that the support has on the ground behavior. The ground reaction curve and numerical modeling was used to evaluate the impact of standing support on ground behavior. LaModel was used to evaluate the impact of standing support on main roof and floor behavior and pillar yielding. The conclusion drawn from this study was that standing supports do not have sufficient capacity to control main roof or floor loading or prevent the resulting convergence of the tailgate entry. However, it is imperative that this “uncontrollable convergence” be considered in the support design to prevent premature failure of the support. A FLAC model was used to evaluate the near-seam roof and floor behavior in conjunction with the global vertical and horizontal stresses. The model suggests that standing roof supports can have some impact on the ground behavior as the elastic response of the rock is exceeded and rock structure deteriorates from the stress concentrations that develop around the tailgate opening. During this phase, the capacity and stiffness of the standing support can be critical to the stability of the opening, as eventually the rock mass will be transformed into a partially detached structure whose weight must be supported by the standing support. This work is part of a ground control program of research at the National Institute for Occupational Safety and Health (NIOSH) aimed at improving mine safety by reducing roof fall injuries and fatalities.

By John L. Dahle

This report documents the research efforts that were undertaken to design, install and test noise abatement devices for use on off-highway haul trucks operating in surface mines. The objective of the program was to reduce the environmental noise from haul trucks. The noise reduction devices that were developed utilized existing technology and were tested on a 50-ton haul truck. The efforts emphasized the reduction of noise emitted from the engine compartment which included the use of side shields, sound absorbing material, improved radiator shroud design, and a modulating clutch fan. Noise tests were conducted using modified SAE test procedures for measuring sound levels around a stationary and moving machine, and inside of the operators compartment. Test results showed a maximum of 4 dB(A) reduction measured 16 feet from the truck. Interior cab noise was reduced 6 dB(A) with the windows and vents closed.

Jan 1, 1983

By Launa Mallett, Charles Vaught, Michael J. Brnich

Purpose: This training material focuses on the content of emergency warning messages. Research has shown that when an emergency occurs, people often do not get the information they need for the purpose of taking appropriate action. This safety talk presents a procedure, using mental cues that can be used by senders and receivers of emergency warnings. Intended Use: This material has been developed for use in short safety-training sessions such as start-of-shift safety or Atoolbox@ talks. The information can be presented in approximately fifteen minutes and is appropriate for workers at all experience levels. While the examples and illustrations are taken from the underground coal mining industry, the training can be tailored to any work setting by substituting appropriate examples. Materials Needed: The instructor will need to prepare the figures provided in a form that can be seen by the entire class. Suggested methods include the use of: (1) overhead transparencies, (2) laminated pages that can be held up for small groups, and/or (3) handouts with copies of the figures for each trainee. As a supplement, stickers featuring the communication triangle can be placed on hard hats, telephones or other communication devices to remind workers about the key to effective emergency communication. The Talk: The accompanying script is a guide for presenting this safety talk. Training is enhanced if these materials are covered but not simply read by the trainer. Examples given in this guide are from real experiences. To make training more interesting and effective, the instructor can substitute examples from his/her workplace. Additional Resources: The following references will provide further information about communications during emergencies. Auf Der Heide, E. (1989). Disaster Response: Principles of Preparation and Coordination. The C.V. Mosby Company, St. Louis. Mallett, Launa, Charles Vaught, and Michael J. Brnich Jr. (1993). A Sociotechnical Communication in an Underground Mine Fire: A Study of Warning Messages During an Emergency Evacuation@, Safety Science, 16, pp. 709-728. Nigg, J.M. (1987). A Communication and Behavior: Organizational and Individual Response to Warnings@ in Sociology of Disasters: Contributions of Sociology to Disaster Research, R.R. Dynes, B. De Marchi, and C. Pelanda (eds.), Franco Angeli, Milan, Italy, pp. 103-116.

Jan 10, 1999

By Charles Vaught, JON VOLKWEIN, ROBERT PETERS, ERICA HALL

Since 1999, the CWP level among miners with 25 years or more experience, for instance, has risen from slightly more than 4% to 9% (See Figure 1). While it is obviously necessary to protect all miners’ lungs, there is now a technology to improve the chances that new miners’ lungs will be protected from the day they begin work.

By Jérôme Boutin, Rémy Oddo, Sylvain Ouellette, Paul-Émile Boileau, Gilles LeBlanc, Pierre Marcotte

ackleg rock drills are widely used in the mining industry and are known to generate high levels of hand-arm vibration which contribute to the development of the hand-arm vibration syndrome for exposed miners.1-3 To reduce the vibration levels, a prototype of an antivibration handle was developed as part of a previous study.4 To provide some bench marking for this handle prototype and to follow the evolution of its performance over time, a test bench was developed to characterize the vibration emission values of jackleg drills under controlled operating conditions. As the current ISO 8662 series of standards could not apply directly to this type of tool, there was a need to design and validate a test bench to evaluate the vibration emission values of jackleg drills, while taking into account the conditions specific to the operation of this type of tool. Methods A test bench including an energy absorber, was developed for testing jackleg drills based on the ISO 8662-3 standard 5. The energy absorber was bolted to a 3300 kg concrete block to ensure tool stability. A pictorial view of the device is given in Figure 1. For validation purposes, acceleration measurements at the handle of a conventional jackleg drill were taken simultaneously along the three axes (xh, yh and zh) in an underground rock drilling operation as well as on the test bench. The handle accelerations were measured for three different jackleg angles (13º, 28º and 43º) determined with respect to the floor. Moreover, each measurement was repeated at least three times to asses the data repeatability. [ ] Results As a preliminary validation of the test bench, Figure 2 provides a comparison of the frequency weighted rms acceleration spectrum measured along the zh-axis, for both underground drilling and operation on the test bench (28º jackleg angle in both cases). It is shown that the vibration measured on the handle of a jackleg drill operating on the test bench is representative of that recorded during typical rock drilling operations, despite the fact that some harmonics of the percussion frequencies are generated with a higher amplitude on the test bench. Table 1 provides

Jan 6, 2006

By H. M. Urban

This paper, one of a series being prepared for and published by the United States Bureau of Mines on methods and costs of mining at various mica mines in the United States, describes the methods now in use in the principal mica mines of the Southern Appalachian States. Those papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in some instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue.

Jan 1, 1932

By Fred N. Kissell, Jerry C. J. Tien, Edward D. Thimons

At coal mine working faces, simultaneous application of three basic elements reduces the methane explosion hazard: (1) adequate ventilation, (2) regular monitoring of gas concentrations, and (3) the elimination of ignition sources. This paper reviews the application of these elements in a manner relevant to Chinese coal mines. Adequate ventilation is provided by using the mine entries to convey air for the long distances between the mine portal and the working sections (main ventilation systems) and then using line brattice or ventilation duct (face ventilation systems) to convey air the last hundred meters to the working face where coal is broken and removed. The air quantity provided is enough to safely dilute methane and the air velocity is enough to prevent layering. Gas concentrations are regularly monitored in accordance with regulations using knowledge of the circumstances under which the highest concentrations are likely to be found. Ignition sources are eliminated by ensuring that electrical equipment does not ignite methane, that sparking from cutter picks is minimized, and that smoking by workers is strictly forbidden. Risk-reduction studies using fault-tree analysis have shown that large reductions in explosion risk only result from multiple preventive actions. For example, a ventilation upgrade or a methane monitor upgrade by itself offers risk reductions under 50 pct. A risk reduction of 90 pct. or more would typically require much more. Other studies have shown that the everyday vigilance of those working underground is as important as engineering design.

Empirical methods involve the scientific interpretation of real-world experience. Many problems in ground control lend themselves to an empirical approach because the mines provide us with plenty of experience with full-scale rock structures. During the past 10 years, powerful design techniques have emerged from statistical analyses of large databases of real-world pillar successes and failures. These include the Analysis of Retreat Mining Pillar Stability (ARMPS), the Analysis of Longwall Pillar Stability (ALPS), the Mark-Bieniawski rectangular pillar strength formula, and guidelines for preventing massive pillar collapses. In the process, our practical understanding of pillar behavior has been greatly enriched.

Jan 5, 1999

By Donald E. Buck

In 1988, Albania's centrally planned economy continued to decline. The country's officially published yearend economic report did not contain concrete results such as the growth of national income or industrial output. 2 The shortfall for central budget earnings for 1988 amounted to 9% below the planned target. Losses in industry were attributed to poor management and organization, as well as to low technical standards and excessive consumption of fuels and raw materials. The construction, energy, and mining sectors of industry did not meet their annual production plans. As in 1987, within these sectors, the chromite and petroleum extracting and processing industries continued to lag in output. Both chromite and petroleum remained Albania's chief sources of foreign exchange; the production downturn of these commodities continued to negatively affect the country's foreign trade position, especially in view of constitutional prohibitions against using foreign credit to finance trade. The chief events in the minerals industry in 1988 included the construction startup of the first of four planned new concentrators at the Bulquize chromite mine, as well as the construction startup of new ferrochromium capacities at Elbasan. Also, the copper mining industry reported the completion of facility expansion at the Perlat mine in the Mid-rite district. Albania began new facility construction at the Dinamo heavy-equipment enterprise at Tirana to maximize self-sufficiency in mining equipment production. Upon completion, the new factory would double the out-put of mining equipment at the enterprise and would introduce new designs for electric trucks and pneumatic drills for the mining industry. The new facility would also increase the production of new machinery and equipment for the country's beneficiation plants.

Jan 1, 1990

By Sean Gallagher, William S. Marras, Alan S. Litsky, Velimir Matkovic, Deborah Burr, John Landoll

Study Design. Survival analysis techniques were used to compare the fatigue failure responses of elderly motion segments to a middle-aged sample. Objectives. To compare fatigue life of a middle-aged sample of lumbosacral motion segments to a previously tested elderly cohort. An additional objective was to evaluate the influence of bone mineral content on cycles to failure. Summary of Background Data. A previous investiga¬tion evaluated fatigue failure responses of 36 elderly lumbosacral motion segments (average age, 81 ± 8 years) subjected to spinal loads estimated when lifting a 9-kg load in 3 torso flexion angles (0°, 22.5°, and 45°). Results demonstrated rapid fatigue failure with increased torso flexion; however, a key limitation of this study was the old age of the specimens. Methods. Each lumbosacral spine was dissected into 3 motion segments (L1-L2, L3-L4, and L5-S1). Motion segments within each spine were randomly assigned to a spinal loading condition corresponding to lifting 9 kg in 3 torso flexion angles (0°, 22.5°, or 45°). Motion segments were statically loaded and allowed to creep for 15 minutes, then cyclically loaded at 0.33 Hz. Fatigue life was taken as the number of cycles to failure (10 mm displacement after creep loading). Results. Compared with the older sample of spines, the middle-aged sample exhibited increased fatigue life (cycles to failure) in all the torso flexion conditions. Increased fatigue life of the middle-aged specimens was associated with the increased bone mineral content (BMC) in younger motion segments (mean ± SD, 30.7 11.1 g per motion segment vs. 27.8 ± 9.4 g). Increasing bone mineral content had a protective influence with each additional gram increasing survival times by approximately 12%. Conclusion. Younger motion segments survive considerably longer when exposed to similar spine loading conditions that simulate repetitive lifting in neutral and flexed torso postures, primarily associated with the increased bone mineral content possessed by younger motion segments. Cycles to failure of young specimens at 22.5° flexion were similar to that of older specimens at 0° flexion, and survivorship of young specimens at 45° flexion was similar to the older cohort at 22.5°. Key words: biomechanics, low back disorders, fatigue failure, age, motion segments, vertebral endplate fractures, torso flexion, lifting, bone mass. Low back disorders (LBDs) are a major cause of both short- and long-term occupational disability in the United States, and it is clear that workers in certain occupations are more susceptible to LBD.2-5 Specifically, epidemiologic studies have shown that jobs involving heavy physical demands such as construction,2,3 mining,2,4 and farming,5 engender increased risk of back pain. These occupations are thought to experience high LBD rates as a result of their extreme postural and manual lifting demands. Studies have shown that jobs involving significant lifting 6-9 and jobs that involve frequent bending10-12 are associated with increased LBD risk. Workers in the mining industry, in particular, often have to lift heavy materials in restricted workspaces that compel torso flexion. An understanding of the impact of repeated loading of the spine in flexion on fatigue failure of spinal tissues is thus a critical issue for our research agency, which is concerned with reducing the pain and disability associated with LBD in the mining industry. It is well accepted that loads experienced by the spine during manual lifting tasks are sufficient to cause fractures in the endplates of lumbar vertebrae, particularly on repeated loading. 13-15 Endplate fractures may not be painful in and of themselves 16; however, evidence suggests that the process of internal disc disruption and disc degeneration may be initiated via endplate fractures. 16,17 It has been shown that endplate damage will alter the distribution of stress in the disc, resulting in buckling of the lamellas of the internal anulus.17 Once this process has been initiated, repeated spine loading will cause additional disruption of the anular fibers, resulting in formation of significant fissures or tears. 11-21 If these tears occur near or extend close to the outer portions of the anulus, a wound healing process is initiated, which involves infiltration of mast cells, macrophages, and re¬lease of cytokines and growth factors. 21 The presence of these infiltrates has been strongly linked to discogenic low back pain. 21,22 Indeed, for patients experiencing chronic low back pain, the prevalence of internal disc disruption is at least 39%,19 which represents the most

By N. A. Eilertsen

Procedures of mining high-calcium limestone underground at the Kimballton mine of the Standard Lime and Cement Co. in Giles County, west-central Virginia, are described. Drilling and blasting procedures area discussed in detail, and direct mining costs are tabulated in percentage of total cost. Output, about 1,725 tons of limestone a day, is attained with heavy trackless equipment by the room and pillar method of mining modified by benching floors. Operating features include underground air compression, electric-eye control of curtained doorways, use of a single jumbo drill rig for all drilling, and an effective plan for maintenance of equipment. The company's safety program has contributed to an outstanding safe mining record. The mine is integrated with a plant on the property which converts the stone to metallurgical and chemical grade lime.

Jan 1, 1964

By W. J. Wenger

Colorado has been producing petroleum since 1863 but only recently has become a major oil State. The first well was drilled on Oil Creek near Florence, but out-put was relatively small until discovery and development of the Weber sandstone reservoir at Rangely. Oil was discovered in the Weber sandstone in 1933, and the reservoir was developed after 1940, bringing Colorado, in 1949, to 11th place among the 48 States as an oil producer. Colorado's output increased further because of the discovery and development of many fields in the Julesburg Basin since 1949 By 1954 Colorado was in ninth place and maintained that position through 1955.4/ Between 1946 and 1951, Colorado's oil production more than doubled, while the total United States production increased only 25 percent. It seems probable that production will continue to expand in Colorado for many years. This report presents analyses of 92 crude oils from 73 fields representing 90 percent of the production in 1955. Abridged analyses are listed for easy comparision, and complete analyses arc given in the appendix. Oil samples were collected for study from many different sources. Although many of the newer fields were not sampled, their oils probably are very similar to those from corresponding formations that were studied and tabulated.

Jan 1, 1957

By E. E. Ungar

The ways in which noise is generated and radiated by chutes and screens are described and corresponding noise control concepts are discussed. The amounts of noise reduction produced by applicable noise control means are delineated and generally cost-effective means are recommended. Available noise control materials and their applications are discussed. The results of field measurements, laboratory experiments, theoretical analyses, and studies of data provided by suppliers are summarized.

Jan 1, 1975

By R. S. Dean

"INTRODUCTION The metallurgical research program of the Bureau of Mines has been somewhat disorganized, but generally advanced by the increased activities of the war period. The present report is for the purpose of summarizing the work of the Bureau in this field for the past 15 years and indicating its future plan.Fifteen years ago the Bureau turned from its pioneer work on the physical chemistry of steelmaking to an emphasis on raking a pure steel synthetically, rather than by refining, that is, :producing each of the steel 'constituents in the pure state and combining them by simple melting. Such a procedure permits the use of less high-grade ores, not only of iron, but of the ferroalloy metals, such as manganese and chromium,This program has led to extensive work on iron-ore concentration, agglomeration, reducibility of ores and agglomerates, direct reduction of iron ores and concentrates by a wide variety of processes; special refining processes for iron, the production of pure mangenese, chromium, and cobalt from low-grade ores by electrolytic processes, the production of ferrochromium, ferronickel, and ferronickel-cobalt from low-grade domestic ores, and the development of many special alloys to effectively use the new products.The status of the work in each of these fields and the future program of work, together with a bibliography of papers and patents by the Bureau staff on each of these subjects, are given."

Jul 1, 1946

By Elaine T. Cullen

Miners, like many skilled blue-collar workers, are not traditional learners. They have not generally been successful in classroom-type settings, preferring to learn on the job in a hands-on environment. U.S. miners are required to have annual safety training, but they rarely view this positively. In fact, it has been called “safety jail” by many of them, who regard it as a time to get a little extra sleep. The challenge then, was to find a way to develop effective safety training for these people, particularly in view of the fact that their work is among the most dangerous of all occupations. Miners are born story tellers. They share “near-miss” stories, stories about master miners they have known, and stories about how things used to be. These stories not only pass along information about what will happen if a miner fails to respect the mining environ-ment, they also instruct listeners in the culture of mining and the values it embraces. Stories, it seems, are a way to get safety messages to miners, especially inexperienced ones, and using older, wiser miners in these stories is an obvious choice. This paper will discuss how the training videos created to get safety messages to miners were developed, how “master miners” and story lines were chosen, and how the resulting videos have been received in the mining industry.

By V. Vern Hutchison

This selected list contains 829 entries with citations to Bureau of Mines publications related to petroleum and natural gas, which were released during the 1961-1970 period. Some entries are multiple in nature, resulting in a total of 881 citations.

Jan 1, 1972

By William H. Schiffbauer

This report details a microcomputer-based control and monitoring network that was developed in-house by the U.S. Bureau of Mines and installed on a continuous mining machine. The network consists of microcomputers that are connected together via a single twisted-pair cable. Each microcomputer was developed to provide a particular function in the control process. Machine-mounted microcomputers, in conjunction with the appropriate sensors, provide closed-loop control of the machine, navigation, and environmental monitoring. Off-the-machine microcomputers provide remote control of the machine, sensor status, and a connection to the network so that external computers can access network data and control the continuous mining machine. Because of the network's generic structure, it can be installed on most mining machines.

Jan 1, 1993

By F. R. Lee

[WHEN the Bureau of Mines was established in July 1910, one of the problems immediately attacked by the new organization was the development of standard, for the design and testing of electrical equipment that could be used without fear of initiating fires and explosions in underground coal mules. Research and investigation by Bureau personnel, supplemented by the published results of similar work by European mining authorities, led to the establishment of standards or "schedules." which guide manufacturers in the design of many types of electrically operated machines and devices used in. underground coal Mining. By issuing these standards, Bureau personnel establish the requirements to be met by such equipment before it tan be approved by the Bureau of Mines as permissible for use in gassy coal mines. Every 2 years the Bureau of Mines publishes a list of equipment that leas been accepted as approved or permissible during the preceding 2 calendar years. This is done to inform the mining industry of the availability of the latest equipment for safe use underground.]

Jan 1, 1964

Past issues of Minerals and Materials have discussed such aspects of the economy as consumption and investment expenditures, interest rates, productivity, and international trade barriers and their effect on the minerals industry here and abroad. In this issue, we will (l) look at recent indications of a possible economic recovery, (2) present 1983 expectations reflecting the results of industry surveys conducted by the U.S. Department of Commerce (DOC), and (3) briefly discuss the contribution of the U.S. mining industry to total gross national product (GNP). THE RECOVERY Throughout most of 1982, DOC's Composite Index of Leading Indicators provided evidence of impending improvement in the economy. The index increased moderately during eight of the months in 1982 and then jumped an estimated 3.6 percent in January 1983 (table 1). While the leading indicators continued to predict improvement, the general economy, as measured by the Index of Industrial Production, continued its slide through November 1982 (table 2). Finally total industrial production increased in December 1982 and continued on an upward path in January and February, as predicted by the leading indicators.

Jan 1, 1983

By W. W. Stephens

As part of the Bureau of Mines program directed toward more effective utilization of the mineral resources of the United States, a number of processes for production of sponge iron have been investigated. The use of sponge iron as a raw material for production of steels and other ferrous alloys offers several possible advantages over the conventional pig-iron and scrap process, especially for utilization of the smeller, widely distributed iron-ore deposits of the western United States. Although considerable information has been made available on various processes for production of sponge iron, little information 118.6 been published heretofore on the problems and costs involved in melting the sponge iron for production of steel. The present Paper reports the results of tests conducted at the Bureau of Nines pilot plant at Redding, Calif. in which several different types of sponge iron Were used as charge material for production of steel in a 4-ton-capacity basic arc furnace.

Jan 1, 1949