Search Documents

By Hsin Wei Wu

A real-time Diesel Particulate Matter (DPM) monitor has been developed on the basis of the successful National Institute of Occupational Health and Safety (NIOSH) designed Personal Dust Monitor (PDM) unit. The objectives of a recently completed Australian Coal Association Research Program (ACARP) study were to modify the PDM to measure the submicrometre fraction of the aerosol in a real-time monitoring underground instrument. Mine testing focused on use of the monitor in engineering evaluations to determine how conditions can be improved. Studies, including a selection during Longwall (LW) moves as described in this paper, demonstrated how DPM concentrations from vehicles fluctuate under varying ventilation and operational conditions. Correlation between the current SKC DPM measurement system and real-time DPM monitors were conducted and results from six mines show a correlation between elemental carbon (EC) and the new monitor DPM mass ranging from .51 to .81 with R2 >.90. These differences are suspected to be due to variations from mine to mine in aspects such as mine atmospheric contamination, vehicle fleet variations, fuel type, engine maintenance, engine combustion efficiency, engine behaviour or interference from other submicrometre aerosol. Real-time monitoring readily reflects the movement of individual diesel vehicles and allows pin-pointing of high exposure zones such as those encountered where various vehicles work in areas of constrained or difficult ventilation. DPM monitoring approaches that have been available for some time based on shift average monitoring do not readily allow successful engineering evaluation exercises to determine acceptability of pollution levels. Identification of high DPM concentration zones allows efficient modification of mine ventilation, operator positioning and other work practices t o reduce miners? exposures without waiting for laboratory analysis results.

Jan 1, 2010

By Timothy J. Rohrbacher

This report presents a U.S. Bureau of Mines study that incorporates coal mining factors, coal recovery factors, and economic factors into the definition of an economically recoverable coal resource. The relationship between these factors to the Energy Information Administration's estimate of U.S. coal resources-the "Demonstrated Reserve Base"-is discussed. The Boltsfork 7 1/2-minute quadrangle in eastern Kentucky was selected as the study area. Results indicate that of the original 280.2 M tons of resource in the quadrangle, only 99.8 M tons (35.6%) is recoverable at a mining cost of $25 per ton or less.

Jan 1, 1994

By B. K. Shibler, J. V. Batty, G. M. Potter, H. D. Snedden

"INTRODUCTION As a part of the investigations of strategic mineral deposits in the United States under the Strategic Minerals Act. Engineers of the Bureau of Mines examined and sampled numerous deposits pf fluoride ores in the Western States. Sample from those deposits that warranted further investigation were submitted to the Ore Dressing Section of the Salt Lake Station for metallurgical testing. This paper gives data summarizing the results obtained from laboratory studios of fluorite ores submitted from 12 deposits in Arizona, California, Idaho, Montana, Nevada and Wyomong. Only four of the Ores were found to be amenable to beneficiation for the production of acid-grade fluorspar concentrates with good recoveries. However, all of the samples were amenable to the production of concentrates meeting chemical specifications for metallurgical-grade spar.For the sake of clarity and convenience in presenting data, this report has been divided into six parts, each pertaining to metallurgical studies of fluorspar ores of a single State."

Nov 1, 1947

By Joseph Sabatini

This report, covering the period January through December 1975, contains abstracts of articles concerning all phases of cost engineering and economics for chemicals processing, raining, and other mineral industries. The abstracts are collected from the following sources: 1. Chemical Engineering 2. Chemical Engineering Progress 3. Chemtech 4. Coal Arse 5. Coal Mining and Processing 6. Combustion 7. Drilling 8. Electrical World 9. Engineering and Mining Journal

Jan 1, 1976

By Kenneth Wardell

Criteria have been fully developed for determining the optimum size of oil and gas well blocks. The criteria lead to the formation of well barrier pillars which are, of themselves, inherently stable and take account of variable mine roof and floor conditions. The criteria ensure, through considerations of ground movement, that strains transmitted to well casings, are within tolerable limits of casing specifications. The criteria cater for well barrier pillars in multi-seam mining situations and where previous old mining has taken place. The criteria maintain flexibility in being adaptable to local mine design situations. The criteria are applicable to proposed extraction thicknesses up to 15 feet at depths up to 2,400 feet. The criteria are related to producing wells and to abandoned wells. In the latter connection, various states of well abandonment are recognised.

Jan 1, 1980

By J. E. Urosek, K. L. Cashdollar, D. A. Beiter, G. J. Shemon

The National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research to evaluate explosion blast effects on mine ventilation stoppings at the NIOSH Lake Lynn Experimental Mine (LLEM). After mine explosion accidents, MSHA conducts investigations to determine the cause(s) as a means to mitigate or eliminate future occurrences. As part of these post-explosion investigations, the condition of underground stoppings, including the debris from damaged stoppings, are documented as evidence of the strength and the direction of the explosion forces. The LLEM data showed that a total pressure of 52 kPa (7.6 psi) destroyed the solid concrete block stopping, ~36 kPa (~5.2 psi) destroyed the hollow-core concrete block stopping, and 9 kPa (1.3 psi) destroyed the steel panel stopping. These results will assist investigators in determining the explosion forces that destroy or damage stoppings during actual coal mine explosions.

By Chas. F. Jackson

The mining literature is replete with descriptions of methods and costs of operation at producing mines. To day the mine manager can find published information bearing upon almost any problem with which he may be faced. From this literature he can familiarize himself with methods employed by otter operators for coping with problems similar to his own, under more or less parallel conditions. Transaction of mining societies, publications of the U. S. Bureau of Mines, technical journals, and handbooks all afford valuable information dealing with operating methods and costs, Very little has been published, however, regarding methods and costs of equipping and developing new properties and bringing them to tae productive stage. There may be some question in the minds of many as to the value of papers on this subject, due to the great variety of conditions encountered. No two prospects are alike. Obviously, it is impossible to forecast what expenditure will be required to develop a mine from a raw prospect or even to predict whether the prospect can be developed into a productive mine.

Jan 1, 1933

This section of Minerals and Materials analyzes the following three factors affecting the recent performance of the U.S. and world mineral industries: 1) the health of the U.S. and world economies, 2) the level of interest rates and 3) the performance of productivity in both the U.S. mineral industry and the general economy. While these indicators do not exhaust the possible critical factors, they represent an initial attempt to probe some of the considerations underlying the performance of the U.S. minerals and materials industry. The U.S. and World Economies It is essential to analyze the state of the U.S. and world economy because the demand for minerals and materials is a derived demand; that is, since minerals and materials are used in the productive process, the demand for them is a direct function of the demand for the finished products of which they are a basic input. Thus, the demand for minerals and materials is directly affected by changes in present and planned consumption and investment expenditures. The past two issues of this publication have highlighted the generally discouraging performance of the national and inter-national economies. Briefly, the world economy is in the third year of the first long recession in recent history where inflation rates have remained above 5 percent. With many countries either unable or unwilling to support domestic spending while inflation continues, there has been a growing tendency to institute trade-restrictive policies to support domestic demand. The resulting weakened demand conditions in exporting nations have had a direct effect on the mineral industry.

Jan 1, 1982

Reduce the respirable dust exposure of the roof-bolter operator when downwind of the continuous miner, particularly in mines where respirable dust standards are more stringent because of silica in the respirable dust. Dust Sources If roof-bolter dust levels are excessive, the bolter dust collector should first be checked to ensure that it is operating properly. (Technology News No. 219 provides information on how to spot and repair bolter dust collector problems). If the roof-bolter dust collector is operating properly and dust levels are still excessive, then the source is most likely a continuous mining machine operating upwind. In many sections, the roof-bolter operator must work on the return side of the continuous miner during part of the production cycle. In three-entry longwall developments with single split ventilation, this may happen as much as one-third of the time. Factors which pro-mote high quartz dust exposure are:

Jan 1, 1985

By David S. Brown

What troubles me so often about debates over the environment, which I have heard since I entered government in the late 1960's, is that the issues are so often presented as a false dilemma--the either-or fallacy in logic. The either-or fallacy allows only two possible choices: Either protect the environment or exploit it. In reality, however, there may be a few more options. The diverse, often competing, values that the Earth offers require us to weigh and balance those options through a range of policy options. A quality environment and economic growth and opportunity are not mutually exclusive. First, let me acknowledge that I support a set of resource values recognized in U.S. laws and deemed important down through history for the success of free, progressive, and secure societies: the importance of access to raw materials. Increasingly, however, mineral raw materials have been viewed at best as not particularly relevant to a sophisticated, technologic society, and at worst monstrously destructive of our natural environment. Both perceptions, in my judgment, are wrong.

Jan 1, 1989

By Wilbert J. Huff

The organization of the Explosives Division is indicated by the accompanying chart (fig. 1). As this has been discussed in a previous report3/, it will not be considered further in this report. The activities of the various units are outlined below. I. INFLAMMABILITY OF GASES AND VAPORS4/ Determination of the Explosion Hazards of Combustible Gases and Vapors Found in Mines and Industries The Explosives Division maintains, at the Pittsburgh Experiment Station, a laboratory specially equipped for the determination of the explosion hazards of combustible gases and vapors. Of particular importance, is the determination of the chemical composition within which explosions may occur and beyond which there is no danger of explosion, combustion or inflammation. These limits, known as the limits of inflammability, as determined by this and other laboratories, have been compiled in Bulletin 279 of this Bureau. The last revised edition (1931) of this bulletin has been exhausted. Since it was published, the Pittsburgh laboratory has determined the limits of about 40 combustibles and has ascertained more precisely ant accurately many previously published limits.

Jan 1, 1938

By Robert W. Geehan

"INTRODUCTION A preliminary examination of the Argentena mine was made in 'January 1945 by an engineer of the Bureau, who recommended investigation by diamond drilling. The Bureau conducted a core-drilling project at the mine from April 30 to August 4, 1946. Claims investigated are in sec. 33, T. 24 S., R. 58 E., Mount Diablo base and meridian, in southern Clark County, Nev., about 2.2 miles west of Goodsprings.The Argentena mine has been an intermittent producer of zinc-lead-silver ore since 1926. During the war years, ore was shipped to the Government stock pile at Jean, Nev., and to the International Smelting F. Refining Co.'s smelter at Salt Lake City, Utah. The mine has been shut down at intervals because of lack of a market for mixed oxidized zinc-lead ore.The 12 holes drilled by the Bureau totaled 1902 feet. The program was designed to test for faulted portions of the ore bodies know in the mine and to test favorable areas for similar ore bodies. As a result of this program, one faulted segment of the ore body was found, and it was established that no one was present in a second fault block. Similar blocks remain unexplored in the vicinity of the mine. Two holes drilled in favorable areas several hundred feet from the mine failed to discover new ore bodies."

Jul 1, 1947

By J. C. Edwards

The National Institute for Occupational Safety and Health (NIOSH) implemented a real-time neural network system which can discriminate mine fires from nuisance diesel emissions as part of an atmospheric mine monitoring system in NIOSH?s Safety Research Coal Mine. The real-time response of a neural network to fire sensor outputs was demonstrated for coal and belt combustion in the presence of diesel emissions. The fire sensors consisted of an optical path smoke sensor, a carbon monoxide (CO) sensor, and two types of metal oxide semiconductor (MOS) sensors. The real time neural network was trained with coal, wood, and belt fire experiments with and without diesel emissions background. The trained neural network successfully predicted mine fires with these combustibles in the smoldering stage prior to the onset of flames.

Jan 1, 2005

By E. Chilton

The National Institute for Occupational Safety and Health (NIOSH) has been conducting re-search to determine the influence of mining machine mounted water sprays on airflows and methane concentrations at the face when blowing ventilation systems are used. Tests were conducted in a full-scale ventilation gallery. Airflow speeds and directions were measured at several locations near the face with ultrasonic anemometers. Methane was released from the face and concentrations were measured in the entry at locations above the mining machine using fixed point methanometers. Changes in airflow speed, direction, and methane concentrations were correlated with water spray operations. The test results using different spray arrangements and water pressures showed that operation of the machine-mounted sprayers can improve face ventilation effectiveness by increasing the velocity of airflow moving toward and away from the face. The improved ventilation resulted in reduced methane levels near the face.

By R. E. Brewer

A critical review of the numerous test methods that have been devised for measuring the "plastic" and "swelling" properties of bituminous coking coals and the practical evaluation of the data obtained has long been needed. The author appreciates fully, first, the arduous problem of doing justice to the merits and limitations of the many original test methods and their manifold modifications and, second, the more difficult task of interpreting the test data obtained in their practical applications to the important problems involved in the coking process. It has been the constant aim of the author to point out the broader significance of the test principles employed in the different classes of test methods and the usefulness of the test data obtained in relation to the problem of coking bituminous coals, rather than to stimulate unduly a controversial criticism of the merits and limitations of any particular class of test methods or of individual test methods devised by different workers. The task has been quite difficult because of the almost total lack of accepted test standards and specifications.

Jan 1, 1942

By W. R. Reed, G. J. Joy

The personal dust monitor (PDM) is a new coal mine respirable dust sampling instrument that has the ability to provide accurate end-of-shift and real-time respirable dust exposure data. A hypothetical cost comparison analysis of the PDM with the current MSHA-required coal mine dust personal sampling unit (CMDPSU) was conducted. Some simplifying assumptions were made to create hypothetical cases for analysis. This analysis was limited to respirable dust sampling of one designated operator (DO) and one designated area (DA) for one mechanized mining unit (MMU) which operated one shift per day. Only sampling intervals of the minimum sampling as required by federal regulations and continuous sampling were analyzed. This cost analysis from the company perspective is only one part of an overall cost/benefit analysis that should be conducted at a later date. In this analysis, company-associated costs were examined for both sampling systems. Results show that the PDM, while it has high initial costs of approximately $12,600, may be a cost-effective sampling system for measuring coal mine respirable dust. The estimated present worth cost of conducting the minimum required dust sampling over a five-year life ranges from $5,850 to $19,000 for the CMDPSU, with the higher present worth cost including costs of potential violations incurred. For the PDM, the comparable present worth cost is $14,900 to $19,300, with the lower present worth cost representing a lower capital cost of $8,150 per unit if more than 850 units are produced per year, while the higher present worth cost reflects the result with the higher $12,600 capital cost.

By A. N. Baldwin

This report documents the work performed under Bureau of Mines Contract J0265029 to study and develop two innovative mining systems: ? An underground auger capable of augering into the right and left ribs without repositioning the machine ? A conventional mining system employing recently developed innovative machinery. The report is separated into two volumes to document the two studies separately. Volume I describes work performed and the recommended concept for a bidirectional auger. Volume II describes the studies of mining equipment performance and mining plans developed to determine a conventional mining plan offering improved productivity.

Jan 1, 1977

By David Schlain

"INTRODUCTION Electrolytic manganese is produced by electrolysis of a solution of manganese sulfate and ammonium sulfate in a diaphragm-type cell, metallic manganoese being deposited on the cathodes and sulfuric acid produced at the anodes. The spent electrolyte is used to leach fresh ore that has previously been subjected to a reducing roast; the resulting leach liquor is purified and returned to the cell.The leach liquor produced at the Bureau of Mines pilot plant 3/ at Boulder City, Nev., contains 135 to 140 grams of ammonium sulfate and 32 to 36 grams of manganese (as sulfate) per liter, and has a pH of about 2.5. After neutralization to a pH of 6.4 to 6.6 with ammonia and thickening, 0.10 to 0.15 gram of hydrogen sulfide per liter is added to the liquor to precipitate the heavy metals, and after 15 to 30 minutes the precipitate is filtered off. Residual sulfides and colloidal material are removed by ferric hydroxide formed by adding a small amount of ferrous sulfate to the solution at a pH of 6.5 to 7.0 and passing air through it. The solution is then filtered and clarified as a precoat filter. Finally, 0.1 gram of sulfur dioxide per liter is added, and the solution is electrolyzed in an anode-in-diaphragm cell. The spent electrolyte coming from the cell contains approximately 10 grams manganese, 135 grams ammonium sulfate, and 45 grams sulfuric acid per liter."

Oct 1, 1946

By E. V. Deshayes, W. E. Young

"INTRODUCTION The Camp Bird mine was investigated by Bureau of Mines engineers 3/ September 22 and 24, 1942, and April 29 and 30, 1944. In a subsequent report and supplement, it was recommended that core drilling be done below the 14th. level to determine if commercial ore existed at greater depths, and particularly if ore existed in the vein or adjacent thereto where it passes into the sedimentary formations estimated to underlie the volcanics approximately 400 feet below the 14th level.Seven diamond-drill holes aggregating 3,956 feet were drilled. Four of these holes were under the Hematite ore body and three were under the Big Discovery ore body. Two holes under, the Hematite ore body wore directed at angles but little steeper than the angle of dip of the vein and penetrated the sedimentaries beneath the volcanics close to the vein. Enough low-grade ore was found at the base of the Telluride conglomerate to indicate the presence of a large body of low-grade zinc sulfide ore. Two holes were directed to crosscut the vein at a depth of approximately 125 feet below the 14th level. No commercial ore was cut, but the vein showed the average width and same general characteristics as at the 14th level. One hole under the Big Discovery ore body was directed to crosscut the vein and test the base of the Telluride conglomerate in the footwall block. No commercial ore was found in either the vein or the sedimentary horizon. One hole was directed to test the base of the Telluride conglomerate in close proximity to the vein in the hanging-wall block. This hole was lost approximately 100 feet short of its objective, and a third hole was drilled to accomplish this same thing. The third hole was stopped approximately 50 feet short of its objective when failure of equipment caused a recess of the"

May 1, 1948

In 2001, 14,623 mining operations reported employment statistics to the Mine Safety and Health Administration (MSHA). This was an increase of 210 mining operations compared to 2000. Almost half (49%) were sand and gravel mines, followed by stone (29%), coal (15%), nonmetal mines (5%), and metal mines (2%).

May 1, 2003