Search Documents

By Bernard Baum

Combined preservative/fire retardant systems were pressure impregnated into Douglas fir and Ponderosa pine samples and evaluated for decay, flammability, and mechanical properties. The objective of the evaluation was to identify cost-effective systems for use with mine timber, and to provide an information and data base from which Federal code regulations could be established. Thirty systems, based on combinations of commercially available preservatives and fire retardant impregnants and coatings, were applied to Douglas fir samples and evaluated for decay and flammability. The ten most promising systems were ap¬plied to both fir and pine and reevaluated for decay and flammability before and after water leaching. The five best systems were given a thorough laboratory evaluation using both pine and fir. Evaluations included flame spread, smoke density, toxic gases, decay, compressive strength, flammability after artificial weathering, and cost. All systems had acceptable toxic gas levels and smoke densities, but flame spread was only borderline acceptable for most of the samples tested. A trade-off analysis showed Acid Copper Chromate/Fyrprufe with Albi-107A/144 intumescent paint and Koppers NCX to be the-best systems. Recommendations are made for further large-scale testing using the two best Systems.

Jan 1, 1978

By Kenneth R. Sites

Under this program two tape recording and triggering systems were developed and delivered for use in the Bureau of Mines microseismic program. The systems are designed to improve the effectiveness of the Bureau owned Sangamo 3500 series and SABRE VI instrumentation tape recorders. The system is designed to capture random microseismic data, digitize and temporarily store these data, start the tape recorder; and then transfer the data to magnetic tape for permanent storage. The system is designed to pack data on tape such that the tape may be simply played back through galvo drivers onto an oscillograph such that a continuous series of analog records, with corresponding time of day information, are reproduced without excessive oscillograph paper waste or the need for the operator to search for valid events.

Jan 1, 1980

By John Organiscak

A majority of continuous mining machines employ a water spray system and a machine mounted flooded-bed scrubber to suppress and capture dust during coal mining. These machine mounted dust control systems must be designed to function within the localized face ventilation system at the mining section to control both dust and methane. Spray systems can impede or improve the scrubber effectiveness in controlling dust or methane at the mining face. Laboratory experiments were conducted to examine the effect of spray type, spray pressure, machine body blocking sprays, and scrubber airflow on dust and gas levels while using a 12.2 m (40 ft) exhaust ventilation curtain setback from the face. These experiments were conducted with the mining machine positioned at the end of a simulated 6.1 m (20 ft) sump and slab cut. Results indicate that the hollow cone nozzles with blocking sprays best complemented the flooded-bed scrubber performance in an exhaust ventilation system. This external spray system notably reduced dust and gas levels on the off-curtain side of the mining machine for both the sump and slab cut as compared to the flat spray nozzles. Higher scrubber airflows reduced dust and gas levels on the curtain side and in the return of the continuous mining machine. The remote operator position, located on the off curtain side and parallel to the inlet end of the exhaust curtain, sustained the most stable and lowest dust levels around the mining machine.

Jan 1, 2010

By M. E. Tyrrell

To promote greater use of abundant domestic raw materials in the manufacture of synthetic mullite, the Bureau of Mines has undertaken a comprehensive investigation to determine the effects of the impurity oxides TiO2, Fe203, and alkali on physical properties of sintered mullite-forming mixtures. The first part of the report presents the results of work covering a major area within the mullite study; namely, the effect of impurity oxides on volume stability, one of the outstanding characteristics of mullite refractories. The volume stability of 20 compositions in each of 3 alumina- to-silica ratios, which blanket the range commonly found in purchase specifications, has been determined following procedures of Navy Specifications B-15606 A for Grade A high-alumina refractories. Results indicated that so long as 5 percent of impurities are combined approximtely in the proportions of 3 percent Ti02, 1 percent Fe203, and 1 percent alkali, sintered mullite-forming compositions in the almina to silica range tested will be volume stable. A permissible tolerance of one-half per- cent in each impurity oxide provides a range that includes values common in the natural minerals from which sintered mullite may be made. Within the total range of 5-percent impurity mixtures, a greater number of volume-stable compositions were obtained by increasing the alumina-silica ratio.

Jan 1, 1962

By Walter D. Holland

This instructors guide is intended for use in a course which teaches metal and non-metal mine inspectors to perform surveys for inhalation contaminants in above ground metal and nonmetal mine work areas. The handbook entitled "Handbook for Surveys of Inhalation Contaminants in Above Ground Metal and Nonmetal Mining and Processing Work Areas? is used as a manual during the course. The manual contains a survey check list, rules for determining if sampling is required, a list of most frequently encountered contaminants, a list of candidate contaminants and their sampling conditions, and a description of control procedures and devices. There are several experiments in this guidebook which the trainees perform to acquaint them with the sampling systems.

Jan 1, 2011

Introduction MINING IS THE BRANCH OF INDUSTRY involving the exploration and removal of minerals from the earth (figure 1). Mining is one of the oldest and most important endeavors of humankind, because it provides the raw ingredients for most of the material world around us and, like agriculture, is the lifeblood of civilization. The main objective of any type of mining is to remove the valuable material economically and safely with minimum damage to the surrounding environment. The Earth has many natural resources on which we depend that must be mined. Coal, oil, gas, and other mineral fuels are used for heating electricity, and numerous industrial processes. Nonfuel minerals such as iron ore, precious metals, and industrial metals, and nonmetallic materials like sodium and potassium are used in chemical and agricultural applications. Even crushed stone used in road building and other construction projects must be mined. Mining affects our standard of living and impacts almost everything we do. A myriad of items that we use in our homes and offices and for transportation, communications, and national defense all require minerals (figure 2). For example, more than 30 different minerals are needed to make a television or telephone! Table 1 lists several commonly mined materials and some of the end uses in our daily lives.

Jan 1, 1995

By Loren R. Anderson

This is an Appendix of Volume I. In contains the results of the electric cone penetrometer soundings from the second phase of the testing program.

Jan 1, 1982

By Rimas Pakalnis, Andrea M. Ouchi, Thomas M. Brady, Mary M. MacLaughlin, Cristian Caceres, Paul Hughes

A major focus of ground control research presently being conducted by the Geomechanics Group at the University of British Columbia, Canada, in conjunction with the National Institute for Occupational Safety and Health’s (NIOSH) Spokane Research Laboratory, is the development of design guidelines for underground mining within weak rock masses. The study expands upon the span design curve for man-entry operations and the stability graph for nonentry operations developed at UBC by extending the application to weak rock masses. The original database has been augmented by weak rock mass information from mines throughout the United States, Canada, Australia, Indonesia, and Europe. The common factor in all of these mines is the presence of a weak back and/or walls. This paper expands on the North American database and how the design curves have been employed at mining operations throughout the world. The definition of a weak rock mass for this study has been defined as having an RMR76 under 45% and/or a Q-value under 1.0.

Jan 5, 2007

By D. K. Caddel

Several problems exist with the present design of coveralls used by miners in low coal (seam height 48 inches or less). The back portion of the coveralls often tears when roof bolts or rough areas in the roof are hit. Movement in the shoulder area is restricted. Female low coal miners find it difficult to purchase coveralls that fit properly, and must remove both their hard hat and safety belt in order to urinate and defecate. The objective of this research was to design coveralls which would alleviate these problems. The following features were incorporated into the coveralls; padding in the upper back area to avoid tearing, an action pleat in the shoulders to increase mobility, an inseam zipper to more easily allow miners to perform their bodily functions, and reflective tape to increase visibi¬lity of the miner. A heavyweight denim fabric was used to increase warmth and durability of the coveralls. The coveralls were assessed K long four parameters (comfort, safety, worker productivity, and fabric suitability) using both an in-field assessment by low coal miners and simulation studies. The experimental coveralls proved superior to conventional coveralls along all four parameters. Work clothing sizes for female miners were developed.

Jan 1, 1982

By John C. Ferm

This report summarizes the results of an investigation of geologic factors that contribute to roof quality in underground mines in the Pocahontas #3 coal bed in southern West Virginia and southwestern Virginia. The investigation consisted of three phases, the first of which was selecting for detailed study five mines which represented the range of roof conditions, mining practices and geologic phenomena. This was accomplished by a statistical analysis of questionnaire data from 35 mines. The second phase consisted of detailed mapping in a "good" and a "bad" top area in each of the five selected mines and resulted in a qualitative assessment of geologic factors contributing to roof £alls. In the third phase, five mines were selected in which most non-geologic factors believed to contribute to roof falls were relatively constant but displayed a wide variety of geologic characteristics. Data from these mines were analyzed to test the qualitative assessments from Phase II. The primary result of this investigation is that slickensides arising from different geologic causes are the major geologic features leading to roof falls. These slicken-sides are found in ancient slump deposits, fire clays and sandy fire clays and channel contacts. Falls also occur where thick sandstone bodies directly over-lying the coal contain abundant shale or ironstone pebbles and coaly strips. The best top material is a sequence which consists of shale grading upward to sandy shale and sandstone within 30 feet of the top of the coal. Thick sand-stone units (301) without pebbles also provide good top.

Jan 1, 1978

By William R. Archibald

This report presents the results of a program demonstrating the technical and economic feasibility of hydraulic borehole mining of uraniferous sandstone. This mining technique involves the drilling of a borehole from the surface down into the ore body. A borehole mining tool consisting of a high-pressure cutting jet and a slurry jet pump is lowered down the borehole. Water from the high-pressure cutting jet cuts into the sandstone formation generating a water-sand slurry which flows to the slurry jet pump and is pumped to the surface. The cutting jet is rotated and moved up and down from the surface, thereby generating a cavity in the formation. When the cavity size reaches a point beyond the effective radius of the cutting jet, the mining tool is moved to an adjacent borehole and the process is started again. This program was carried out in four phases. Phase I included modifications to the borehole mining system (built and tested under a previous contract, No. H0252007, for the mining of coal) and factory tests of the jetting system. Phase II covered the field tests and a public demonstration. Phase III involved nozzle and equipment modifications and factory tests. Field testing continued under Phase IV along with an evaluation of this method. The field tests were conducted successfully on Rocky Mountain Energy Company's Nine Mile Lake property near Casper, Wyoming. Results indicate that; hydraulic borehole mining of uranium is technically feasible (300 tons of uraniferous sandstone were mined from a depth of 90 ft) and the hydraulic borehole method is economically attractive. However, additional testing is required to clearly define the economic feasibility.

Jan 1, 1978

By W. I. Nissen

This Bureau of Mines report presents the design for a commercial-sized flue gas desulfurization (FGD) demonstration plant that uses the citrate process. The goal of the Bureau's citrate process is to minimize the undesirable environmental impacts of industrial plants emitting SO2-bearing gas. The FGD plant is located at the George F. Weaton powerplant, Monaca, Pa. Construction was completed in April 1979 and will be followed by preliminary testing and a 1-year testing and evaluation program. Design capacity of the FGD plant is 156,000 scfm of 0.2-volume-percent-SO2 flue gas yielding about 16 tons of sulfur per day. The plant is intended to (1) clean fly ash, SO2, and Cl- from the gas while cooling the gas in a venturi scrubber, (2) absorb SO2 from the gas using 1,200 gpm of a countercurrent-flowing citric acid-sodium citrate-sodium thiosulfate solution, (3) react the absorbed SO2 in two 13,000-gal stirred closed vessels with added H2S, thus precipitating elemental sulfur and regenerating the citrate solution for recycle, and (4) recover the sulfur from the slurry by air flotation, followed by melting in a heat exchanger and separation from the occluded citrate solution in a sulfur decanter at 35 psi and 135° C.

Jan 1, 1979

By Robert Merritt

Approximately 2,500 tons of low-grade uranium ore were used to conduct a field-scale heap leaching test as well as throe column leach tests. The ore used to construct the field-scale heap leaching test had a grade 0.023% U308 while the ore used fur column leach tests had a grade of 0.027% U308. The ore was crushed to minus 4 in. The field-scale heap was constructed on a clay base with parallel effluent lines running under the heap spaced 7.5 ft apart. The heap was leached for 45 days, drained, washed, and dismantled. Based on residue analysis, approximately 205 tons of ore were leached with a final U308 extraction of 96%. The heap was 17.9 ft in height and leached in a near-vertical pattern down to approximately 1 ft, at which point the leached zone become bell-shaped. Two 8-ft column charges and one 18-ft column charge were leached for 36 and 45 days, respectively. Based on residue analyses, all U308 extractions were greater than 96%. The conclusions generated by the studies showed that (1) flow rates were similar for column leaching and field-scale leaching, (2) final U308 extractions were the same for both types of leaching; however, the deeper ore beds tended to require longer leaching times, and (3) the reagent requirements were reduced with increased bed depth.

Jan 1, 1980

By Diane M. Doyle-Coombs

In late July 1985, air samples from a sealed portion of the Quinland coal mine in West Virginia showed the presence of carbon monoxide (CO). Mine Safety and Health Administration (MSHA) personnel concluded that a fire was burning behind the seals. Since an imminent danger existed, the mine operator was given a closure order. The gases behind the seals were monitored and almost 2 million ff of carbon dioxide (C02) gas was pumped into the sealed area to stabilize the environment. Sixteen days after the closure order was issued, MSHA allowed the mine to return to production. Approximately 1 yr later, mine management submitted a seal breaching request to MSHA in order to drive a set of entries to further develop the mine. The Bureau of Mines established a sampling strategy and monitored gases from behind the sealed area during the breaching operation until the atmosphere was safe. This report is an account of the seal breaching conducted by the mine, MSHA, and the Bureau. The logistics of this event, the sampling strategy, and the equations applied could be used by the mining industry in future breachings or mine recovery operations. Time to reenter the area was calculated by using the methane (CH4) concentrations sampled at the discharge of the seals. Tracer gas was used to verify the ventilation flows through the area.

Jan 1, 1988

By J. F. Neill, O&apos

The manganiferous schists occurring in the vicinity of Kings Mountain, North and South Carolina, suggest significant tonnages of potential submarginal ores. Although some reconnaissance work in connection with these deposits has been reported, no recent information has been published. Evaluation of the schists as a possible domestic manganese resource has not always adequately considered the fact that the manganese content occurs quantitatively both as oxide and as the silicate, spessartite. The Bureau of Mines investigation herein reported includes preliminary studies to indicate the extent of manganese oxide mineralization and to deter-mine the amenability of the material to sulfur dioxide leaching. The field reconnaissance studies suggest a resource containing in one area an average of 6.4 percent manganese as oxide. The procurement of depth information was beyond the scope of the investigation.

Jan 1, 1962

As a result of early experiments in underground mine illumination, the Bureau of Hines recognized the need for additional experience with the underground lighting of coal mines having low seam thicknesses. There was already experience with tile illumination of coal mines having higher coal seams, and this contract with Ocean Energy Inc. (OEI) was undertaken to contribute to the "low coal" experience. For the purpose of this contract, a "low coal? mine is defined as one having less than 45 inches of overall headroom in the working places. As a practical limit, 26 inches was the minimum coal seam thickness to be encountered in this program. In one instance, the maximum coal seam thickness was eight to ten feet, however, this particular work was at the direction of the Technical Project Officer (TPO) by virtue of the unique type of lighting arrangement that was to be evaluated which would be useful for low coal. At the outset of the contract, three major tasks were established. The first two tasks involved the installation of permissible fluorescent lighting equipment at two low coal mines. The intention was to illuminate mining sections in each case consisting of one or more machines. The third task was to illuminate a variety or mining equipment including a longwall. For the purpose of this report, the fol-owing identifies the particular installations associated with each task.

Jan 1, 1976

By Stephen E. Mosher, Suzanne D. Smith

Ground, air, and water vehicles can expose humans to substantial multi-axis vibration. Multiple input/multiple output relationships or models exist for estimating frequency response functions of linear systems1, 2. These relationships have been applied by some investigators to evaluate the effects of occupied seat vibration3, 4. Using a multiple input/single output model, this study investigated the effects of single- and combined-axis vibration in the fore-and-aft (X), lateral (Y), and vertical (Z) directions on vibration transmission to the human chest. Frequency response functions (transmissibilities) were estimated and compared for the back-on and back-off postures. Methods A rigid seat with seat back was mounted onto the Six Degree-of-Freedom Motion Simulator (SIXMODE). A flat acceleration vibration signal was generated between 2 and 40 Hz at 1.0 ms-2 rms in the single and combined X, Y, Z, XY, XZ, YZ, and XYZ axes. The signals were shifted in time so that the combined inputs were not fully correlated. Lightweight triaxial accelerometers were used to measure accelerations at the seat base (input) and at the bony manubrium of the chest (output). The maximum of nine frequency response functions (H(?)) or transmissibilities were estimated from the auto- and cross-spectra. The system transfer matrix for the XYZ inputs and chest Z output is [ ] where PxZ, PyZ, and PzZ are the cross-spectra between the three inputs at the seat base and the Z output at the chest, respectively, and Pxx, Pxy,…zz are the auto- and cross-spectra between the input signals (? not shown in Eq. 1). Equation 1 can be similarly written for the chest X and Y outputs. Matlab® was used to estimate the auto- and cross-spectral densities for calculating the transmissibilities, ordinary coherences (for single inputs), partial coherences, and multiple coherences. Results Figure 1 illustrates the major chest transmissibilities observed for the two postures. Vertical vibration showed a consistent influence on the chest X response (Chest X/Z), most likely causing chest pitch. Some chest Z responses were observed with X-axis inputs, but the results were variable and difficult to interpret. In general, other factors besides the known inputs did not affect the transmissibilities shown in Figure 1 (Repeated Measures ANOVA, P<0.05). This was

Jan 6, 2006

By Larry R. Powell

As part of the Bureau of Mines effort to establish a comprehensive subsidence data base for subsidence technology development, subsidence and related data are being compiled for various mining, geological, and environmental situations. This publication presents data for a longwall mining operation in the Northern Appalachian Coal Region. Vertical displacements and relative faze positions are tabulated for 160 subsidence monuments. Measurements were taken 32 times during the 2 years it took to mine the two panels. Brief physiographic and geological descriptions of the mining site are presented along with a general account of the mining and subsidence monitoring methods.

Jan 1, 1981

By Irvin G. Burough

ANDROS INCORPORATED has designed, manufactured and delivered four handheld C02 DETECTORS and three handheld CH4 DETECTORS. These instruments are for in-mine safety use. The DETECTORS incorporated an NDIR optical/electronic analyzer design in which exceptional zero stability is achieved by pressure modulation of the sample gas. This eliminates the need for daily calibration. This stability and the miniature design (2.5" x 4.5" x 4.5"; 4.5 lbs) of the C02/CH4 DETECTORS provide practical instruments suitable for routine safety inspections. This report includes the theory and design of the instruments as well as studies of gas-pressure modulation by a piezoceramic-driven Helmholtz resonator.

Jan 1, 1979

By Meliton M. Garcia

The volume of gases produced in major and trace amounts following the detonation of two water gel and two emulsion explosives in a mine were determined. The volume .of the major gases (CO, CO2, NO, and NO2) was measured immediately following detonation, during the mucking operation, and following the removal of the muck. Tests to identify and quantify the gases produced in trace amounts were performed following the detonation only. The volume of each major gas per pound of explosive (ft /lb) ;ranged as follows: CO, 0.0424-0.3231; CO , 0.6819-1.5632; NO, 0.0129-0.1320; and NO2, 0.0019-0.1111.. An approximate average of 95% of the gases produced was found in the test chamber immediately following the detonation, while less that 2% was found in the chamber following removal of the muck. Benzene was the most significant compound found to occur in trace amounts. Scaling tests performed with a water gel and an emulsion explosive suggest that the volume of the gases per unit mass of explosive detonated diminishes as the amount of explosive per blast increases.

Jan 1, 1986