Search Documents

By S. Atallah

A survey was conducted relating to the current practices for the classification of hazardous locations in coal preparation plants. Several plants processing bituminous, anthracite and lignite coal in Pennsylvania, West Virginia, North Dakota, Colorado, Montana and Wyoming were visited. Coal preparation plant operations and designers as well as MESA inspectors were interviewed. The National Electrical Code was discussed with selected members of the NFPA committee and electrical equipment manufacturers. Data provided by MESA on fire and explosion accidents in coal preparation plants were examined. The requirements of the pertinent Federal Regulations, National Electrical Code, National Electrical Manufacturers Association and Underwriters' Laboratories were compared and evaluated. This report consists of two parts. Part I: "Analysis and Review" provides a summary of the findings. Part II: "Recommended Guidelines" consists of recommended uniform guidelines that may be used for interpreting the National Electrical Code as it applies to the classification of hazardous areas in coal preparation plants.

Jan 1, 1977

By Kristine M. Krajnak

Occupational exposure to hand-arm vibration through the use of powered hand tools can result in reductions in tactile sensitivity, grip strength and manual dexterity. In fact, even acute exposures to vibration cause shifts in vibrotactile thresholds in exposed fingers (2,4,5). Although reductions in tactile sensitivity after acute vibration exposures are transient, cellular changes associated with this shift in sensitivity could lead to the more permanent reductions in tactile sensitivity that are a common symptom of hand-arm vibration syndrome (HAVS). Methods Animals. Male Sprague Dawley rats (6 weeks of age) were used for all experiments. Animals were housed in AAALAC accredited facilities, and all procedures were approved by the NIOSH Animal Care and Use Committee and were in compliance with the CDC guideline for care and use of laboratory animals. Vibration exposures were performed by restraining rats in a Broome-style restrainer, and securing their tails to the vibration platform using 6 mm wide straps that were placed over the tail every 3 cm. Restraint control animals were treated in an identical manner except that the tail platform was set on isolation blocks instead of a shaker. Tail temperature and current perception thresholds (CPTs). Rats were exposed to 4 h of tail vibration (125 Hz, 49 m/s2), or restraint. Tail temperature was collected prior to and immediately following the exposure using an infra-red camera. Sensory neuron function was assessed by measuring CPTs with a Neurometer (Neurotron, Baltimore, MD). Transcutaneous nerve stimulation was applied to the C10 region of the tail. Three frequencies were used to test specific fiber types (5 Hz – C, 250 Hz - Ad, and 2000 Hz – Aß). The intensity of the stimulus was automatically increased in small increments until the rat flicked its tail. Tests at each frequency were repeated until the animals displayed 2 responses that were within 2 CPT (or 0.02 mA) of each other (2-4 tests/animal). CPT tests were performed prior to the exposure, immediately following the exposure, and 24 h after the exposure. Data Analyses. Temperatures were analyzed using a one-way ANOVA with animal as a random variable. ANCOVAS were used to analyze the CPTs at each frequency. Temperature at the time of the CPT test was used as a covariate, and animal was used as a random variable Results Tail temperatures declined between pre and post exposure (F(1,25) = 62.85, p < 0.001; mean ± sem pre 25.96°C ± 0.42, post 20.71°C ± 0.77), but were back to baseline levels by 24 h after the exposure in both groups of rats. The ANCOVAs demonstrated that exposure to a single bout of vibration did not alter sensitivity of C (5Hz) or Ad (250 Hz) fibers to stimulation.

Jan 6, 2006

[ ]

Jan 1, 1979

By Robert Blickensderfer

Tungsten alloys with high-temperature strength properties, comparable to the best of alloys recently developed by others, were produced by a new process called here the oxyreaction process. The process involved additions of a powder of a reactive metal compound, ZrN, ZrW2, or HfW2, to a base metal powder, tungsten, which contained some oxygen. The powders were blended, compacted, sintered, and extruded. During sintering, diffusion and internal oxidation occurred to produce reactive-metal oxide particles and solid solutions. A dispersion of oxide particles could be precipitated by heat treating. The oxyreaction process circumvents many of the agglomerating and coarsening problems encountered in the current methods for dispersing a stable oxide in a metal. Oxyreaction strengthening results from solid-solution strengthening and from dispersion strengthening produced by the reactive metal and its oxides. At a test temperature of 1,650° C, the alloys prepared from WW, had tensile strengths up to 70,000 psi and stress-rupture lives up to 142 hr at 10,000 psi stress; the alloys prepared from ZrN powders had tensile strengths up to 80,000 psi and stress-rupture lives up to 27 hr at 10,000 psi stress. Tensile strengthening in the alloys was attributed to Zr in solid solution or to Zr-O-W structures too small to be observed in an electron microscope replica. Stress-rupture life was attributed to a dispersion of submicron Zr02 particles which precipitated and grew to 0.05-to 0.2-micron size during the test. Tensile strengthening and stress-rupture life were dependent upon both the zirconium and oxygen contents with the maximum occurring at roughly 0.9 atomic pot Zr and 0.9 atomic pot 0. Studies of the details of the oxyreaction process were made on the W-ZrW2 alloys and three general steps were determined: (1) The reaction of 0 in tungsten powder with ZrW2 to form relatively large Zr02 particles; (2) the dissolution of remaining ZrW2 into the W matrix and partial internal oxidation to form ultrafine but sparse zirconium oxide particles and possibly to establish Zr-O-W structures; (3) the development of ultrafine Zr02 particles during high-temperature aging.

Jan 1, 1971

Phase I of U.S. Bureau of Mines contract H01220S3, "Improved Sensors and Fire Control Systems for Mining Equipment, II was an investigative effort involving study of the fire problem and preliminary design of a fire protection system. Overall contract objectives included three basic efforts: * Identify problems * Develop a design * Demonstrate a system The first two efforts were conducted during the period June through November, 1972. Phase II will involve testing of system components; construction and testing of a mockup; and demonstration of the system on a truck to prove its effectiveness under actual operational and environmental conditions.

Jan 1, 1972

By G. L. Gates

The waters used to waterflood the Wilmington oilfield were studied by the Bureau of Mines, in cooperation with the city of Long Beach, Calif. Increases in the pressure of the injection wells indicated that they were being plugged by materials suspended in the waters. This study was made to identify the suspended materials, determine their origin, and find methods of preventing their formation. The suspended oil-coated materials were iron sulfide, barium sulfate, calcium carbonate, clay, and sand (or silica). Results indicated that the sulfide, which was as high as 90 milligrams per liter, was the product of sulfate-reducing bacteria. The injection of ocean water increased the sulfate content of the waters in the petroleum reservoirs from 3 to 250 milligrams per liter, thereby furnishing sulfate for growth of the bacteria. The waters were supersaturated with barium sulfate. Laboratory tests showed that sulfide could be removed from the waters by adding iron at a cost of 1 to 2 mills per barrel. The solubility of iron sulfide and calcium orthophosphate in the injection waters was also determined.

Jan 1, 1975

By William L. Crentz

This study of the preparation characteristics of the coals in Indiana County, Pa., is the second in a series of Bureau publications appraising the Nation&apos;s coking-coal reserves by counties and the practicability of upgrading marginal deposits to metallurgical standards. The first publication dealt with the preparation characteristics of the principal coal beds in Cambria County, Pa. Over 95 percent of the coal remaining in Indiana County is in the Upper Freeport, Lower Freeport, and Lower Kittanning beds. Isolated patches of Pittsburgh-bed coal are present, and the Upper Kittanning bed is found in minable thickness at some locations, but production from these sources is not large. The greatest production is from the Freeport beds, which account for nearly 70 percent of the Indiana County coal output. These beds usually contain two or more shale or hone partings and in many places are high in sulfur. The large proportion of bony coal in the Freeport beds &apos;produces a relatively high-ash product. Mining practices vary from place to place, but it is frequently necessary to leave certain bony portions of the bed in place in order to load a satisfactory product. Table 1 shows the county&apos;s coal production, by beds, during 1948.

Jan 1, 1951

By Albert W. Deurbrouck

The percentage of coal cleaned mechanically has increased greatly in the past 30 years. This technological change in preparation methods, accompanied by mechanical innovations in most phases of coal mining, has enabled the industry to supply quality coals at competitive prices. The Bureau of Mines has contributed to this progress by conducting research on coal-preparation problems, by evaluating the performance of domestic-and foreign-made preparation equipment, and by recording advances as they occur in industrial coal-cleaning practices. The Bureau&apos;s work in this field is recorded in the more than 150 technical and scientific publications listed in this volume. These reports, published by the Bureau over the past half century, document the Nation&apos;s progress in a vitally important phase of fuel technology.

Jan 1, 1961

By M. C. Irani

The Bureau of Mines, in cooperation with the Mine Safety Appliances Co., has developed a continuous-recording methanometer utilizing a catalytic combustion detector. The methanometer, which is presently operating at 22 exhaust fans at 14 mines in the Eastern coalfields, is reliable and simple to install, operate, and maintain. The instrument and the details of its installation and calibration are described. Analytical data obtained by infrared spectrophotometer and gas chromatograph are presented to substantiate its re liability.

Jan 1, 1974

By Fred V. Carrillo

Of the total quantity of secondary copper and zinc that became obsolete in the United States from 19b1 through 1970, more than 11 million tons of copper and 10 million tons of zinc were not recovered. These estimates are based on a study of the flow and recovery of old copper and zinc scrap by consumption end-use. This report describes (1) where copper and zinc are being used; (2) when they become obsolete and available as secondary metal; (3) how they are being collected for recycling; and (4) how much might be recovered from scrap that presently is not being recycled.

Jan 1, 1974

By J. Dean Warner

From 1984 through 1987, the Bureau of Mines investigated numerous prospects and new discoveries of columbium, rare-earth elements (REE), uranium, zirconium, and other metals associated with the multi-phased peralkaline granite at Bokan Mountain, southeastern Alaska. This report summarizes the mineral evaluations and estimates indicated and inferred resources for those prospects containing significant tonnage and grade. A total of approximately 96.2 MM lb Cb205 (43 pct of the tonnage at a grade exceeding 0.125 pct Cb205), and 11.8 MM lb U308, 27.9 MM lb Th02, 133.0 MM lb Y203, 637.6 MM lb ZrO2, and 241 MM lb REO are estimated to be contained within nine deposits totalling 37.8 million tons (at least 80 pct of resource tonnage also exceeds 0.5 pct Y203 + REO). Generally, half of the REO content is composed of the heavy yttrium subgroup. Several deposits also contain beryllium and tantalum; 2.1 MM lb of Ta205 and 8.9 MM lbs of BeO were estimated. These estimates would likely be substantially increased with additional exploration. Four deposit types were investigated; shear zones and fracture-related deposits, pegmatites, mineralized dikes, and placers. Mineralized dikes contain most of the beryllium, columbium, tantalum, yttrium, zirconium, and REE resources, whereas shear zones and fracture-related deposits (Ross-Adams mine) contain the principal of the uranium resource. Pegmatites are similarly mineralized as are dike deposits, and contain low levels of gold. Placer potential is suggested, but no deposits were found.

Jan 1, 2011

By D. Harrington

Seldom, if ever, has any mining hazard presented itself that some method has not been devised to control it to some extent; the degree of success of such control depends largely upon the intensity of desire to prevent suffering, injury, and death. The economic saving to be realized and the more definitely this is realized by all concerned, the more quickly and effectively will the hazards be handled is an important incentive to prevention of accidents. Preventing coal-mine explosions is by no means a complex problem; all that is necessary is sensible, conscientious, sustained effort. The fact that explosions can be prevented has been well-demonstrated by the record of the post few years; the average annual death toll from explosions for the 5 years 1906-1910 was 438, and for the 20 years prior to 1929 it was 265: during the past 4 years an average of only 32 deaths per year resulted from this cause, although the annual production during that time varied but slightly from that of 1906-10. This is a truly remarkable reduction, and if other types of mine accidents had been reduced in the same ratio only about 300 would be killed annually in our mines instead of the nearly &apos;1,300 killed in 1936 and the approximately 2,000 killed annually for many years. Although frequency of occurrence of explosions has not lessened greatly during the last decade, their severity decreased markedly, which would indicate that effective means are being taken to prevent the spread of explosions, even though ignitions and their causes are not being handled nearly as effectively as they might or should be handled. Several large coal-producing States, which in the past have experienced numerous disastrous explosions, have been free from such disasters for continuous periods as long as 8 years in the relatively recent past. The application of rock dust to underground surfaces has been an important factor in preventing widespread explosions; some of the mast dangerous mines have been rock-dusted fairly adequately, and this has been amply repaid in the reduced severity of explosions, as heretofore indicated; however, many have applied rock dust apparently without giving much consideration to the amount required to prevent

Jan 1, 1938

By Jesse J. Brown

Over 60 simple; were prepared and forwarded to Dr, S. Z. Toma, TPO, PMSRC as a result of this project. Included among these samples were various low temperature forms of silica. Samples of quartz, cristobalite, and tridymite with iron, manganese, and titanium impurities present were prepared. In addition, a long series of samples both wet ground and dry ground for times from 1/2 to 8 hours were prepared. Numerous miscellaneous samples were submitted which included kaolinite, calcite, muscovite, illite, montmorillonite, Ba3(P04)2, and YPO4 among others, in response to special requests from the TPO. The silica rich portion of selected binary (CA 203-Si02, In 203-Si02, Li20-Si02) Na20-Si02, PbO-Si02, SnO2-Si02, Sn02-Si02 BaGa204-SiO2 and SrGa204-Si02) and ternary systems (Na20-Ga203-Si02 and Li20-Ga203-Si02) was investigated to determine the effects of solid solubility on the stabilization of the high temperature forms of tridymite. In addition to the determination of the extent of these crystalline solubilities, observations were made. on the mechanism of the transformation of silicic acid to tridymite and the rate of the reaction in the presence of foreign ions,

Jan 1, 1973

By O. C. Blade

In its general study of crude petroleum, the Bureau of Mines has published several reports that include analyses of samples of crude petroleum from Oklahoma fields3/. This report discusses briefly the properties of crude oil samples collects in come of the major producing Yields in the State. ACKNOWLEDGMENTS This investigation was conducted by the Bureau of Mines in cooperation with the State of Oklahoma. The study was via e under the general supervision of R. A Cattell, chief engineer, petroleum and Natural-Gas Division, Bureau of Mines, Whishington, D. C., and N. A. C. Pith, supervising engineer, Petroleum Experiment Station, Bureau of Mines, Bartlesville, Okla., and. Under the direct supervision of Ludwig Schmidt, senior petroleum engineer, Bureau of Mines, Bartlesville, Okla.

Jan 1, 1939

By Thomas O. Glover

Cameroon continued to enjoy sustained economic growth that began with its independence in 1960. Growth in the gross domestic product (GDP) averaged 2.8% per year during the 1960&apos;s and the first half of the 1970&apos;s. Starting in 1976 and for the succeeding 10 years, the GDP accelerated rapidly owing to the coming on-stream of Cameroon&apos;s small but domestically significant offshore oil industry. In 1985, the GDP grew by 7.8%, but in 1986, it was only up 5.5%. The country&apos;s sustained economic growth in dollar terms of gross national product (GNP) per capita reached $1,075 in 1986. The ranking in GNP per capita by the International Monetary Fund put Cameroon in the middle-income category for developing countries. The sustained economic growth rate up to 1986 was due to the injection of income from oil into the economy, but crude oil price reductions in 1986 brought a slowdown. In 1986, crude oil production grew to 200,000 barrels per day, an increase of 8.2% from that of 1985. Most of the oil came from the Société Nationale Elf Aquitaine (SNEA) wells in the multifield Rio del Rey complex. Additional output came from the Moudi Field operated by Compagnie Française des Pétroles S.A. Proven oil reserves in Cameroon were 540 million barrels. At 1986 production rates, and in the absence of further discoveries, Cameroon will have exhausted its recoverable oil reserves by the year 1995. Owing to worldwide crude price reductions, the country&apos;s oil income fell 60% between 1985 and 1986, from $1.82 billion2 to $0.72 billion. Cameroon&apos;s refinery operator commenced operating the Sonara refinery in 1981 at Point Limboh. Sonara&apos;s capacity of 43,000 barrels per day was small by most standards. In 1986, natural gas reserves, estimated at 100 billion cubic meters, were not produced commercially because there were no domestic users. Proposals for a multibillion-dollar liquefied natural gas plant at Kribi had been submitted; however, work on the plant had not commenced.

Jan 1, 1988

By R. W. Stahl

An award is a form of recognition given for superior performance in a special field of endeavor. Each year awards are given by the Joseph A. Holmes Safety Association and the National Safety Council to mineral industries&apos; mines, quarries, and plants that have worked a specific number of man-hours without a lost-time injury. These awards have a dual significance in that they prove that efficiency can be attained without injury to persons. Safety awards do not result from luck or good fortune but do result from sincere desire coupled with sufficient effort and cooperation to achieve a desired goal.

Jan 1, 1963

By O. C. Blade

[In its general study of crude petroleum, tic Bureau of Mines has published several reports that include analyses of samples of crude petroleum from Oklahoma fields3/. This report discusses briefly the properties of crude oil samples collects in come of the producing fields in the State ACKNOWLEDGMENTS This investigation was conducted by the Bureau of Mines in cooperation with the State of Oklahoma. No study was made under the general supervision of R. A Cattell, chief engineer, petroleum and Natural-Gas Division, Bureau of Mines Washington, D. C., and N. A. C. Smith, supervising engineer, Experiment Station, Bureau of Mines, Bartlesville, Okla., and under the direct supervision of Ludwig Schmidt senior petroleum engineer Bureau of Mines, Bartlesville, Okla.]

Jan 1, 1939

By Israel Liebman

The Bureau of Mines conducted an investigation to determine those factors that are significant in affecting the velocity of flames propagating along the boundary separating gaseous fuel and air. In addition the aerodynamic motion of the gases in the vicinity of such interfacial flames was delineated. Parameters in the study included flammable zone thickness, flammable zone concentration of gradient, fuel type, and position of the flame relative to various environmental surfaces. Of all these factors, the flammable zone thickness and burning velocity of the stoichiometric mixture were found to have the most significant effect on the flame speed. Notion of the gases in the vicinity of the interfacial flames was examined by particle track and interferometric techniques. The relative velocity of the interfacial flame with respect to the unburned gas on the central streamline was found to equal the burning velocity of a stoichiometric homogeneous fuel-air mixture. In addition, it was observed that the composition of the lean fuel-air mixture at the boundary of the combustion zone appears to be less than that defined as the fuel&apos;s lower flammable limit.

Jan 1, 1968

By G. N. Schrauzer

Work has been carried out in the development and testing of carbon monoxide (CO) detection devices which use silica-gel impregnated with metal salts. If carbon monoxide is present, the ?detection gel? (the treated silica-gel) changes from a yellow to a blue-green or blue color. The detection gel "regenerates", i.e., returns to its original yellow color, within 4-24 hours after removal from air containing CO. The detection gel exhibits a threshold of CO response which can be adjusted over a wide range of CO concentrations, typically from 50-500 ppm in air. The preparation of detection gel using salts of palladium, molybdenum and copper is described. Also reported are the results of testing the detection gel&apos;s response to carbon monoxide under varying conditions of temperature and humidity and in the presence of some potentially interfering gases. Low levels of hydrogen sulfide (~ 5 ppm)1 nitrogen dioxide (< 7 ppm), and acetylene (> 200 ppm) were found to affect the detection gel. Temperature and humidity were also found to affect the detection gel&apos;s response. Increasing temperature shortens the gel?s response time while increasing the humidity delays the gel?s response and alters the threshold of the gel. A brief discussion of the further research and development necessary to stabilize the detection gel?s desirable characteristics is included. Descriptions of testing equipment and procedures are covered in detail.

Jan 1, 1978

By Russell J. Gartrell

This report describes the engineering feasibility and economic advantages of using a steep angle conveyance (SAC) system in conjunction with medium and large draglines to transport spoil in a typical Western Coal Mine. The SAC system, including a receiving hopper, a steep angle conveyor and a sticker/spreader, is capable of processing overburden material at the rate of 7,000 tons/hr. The unique feature of this system is the steep angle conveyor which transports the overburden material from the pit bottom to the top of the spoil at angles to 45 degrees. Compared to other means of cross-pit conveyance considered during this study, the SAC system offers the advantage of easier operation, lower conveyance cost and greater mobility. The results of this study have shown that integration of the SAC system into both established and planned new mines would improve the overall mining operation, expand the operating capability of existing equipment and reduce mining end reclamation cost.

Jan 1, 1977