Search Documents

By W. E. Schroeder

Two underground installations of the sprayfan system are described and evaluated. The spray fan proves capable of reducing by 1300 percent downtime due to high methane. Spray fan face ventilation at 20 ft brattice setback is shown to give improved methane control over conventional sprays at 10 ft setback. In addition, this report describes: ? A simple method for determining the most economical application of ventilation for face methane control ? The effect of place variables (primary ventilation, auxiliary ventilation, seam height, etc.) on methane concentrations ? The correlation of methane concentrations with brattice setback. These results are utilized to suggest a safer and more economical approach to face methane control.

Jan 1, 1981

By Steven J. Schatzel, Robert B. Krog

Frictional ignitions are defined as the ignition of a flammable mixture of methane and air that is initiated by frictional heating. Ignitions created through the addition of energy from open flames and exposed electrical circuits are not included in this analysis. Energy released in a roof fall that creates a spark and ignites a methane mixture would be considered a frictional ignition. Frictional ignitions represent the majority of all ignitions in underground coal mines. Over the study period of 1983 to 2005, a total of 1993 ignitions were reported in underground bituminous coal mines in the United States, of which 1589 were frictional ignitions. Reportable ignitions to the Mine Safety and Health Administration (MSHA) are any unintentional occurrences of flame underground regardless of duration. Frictional ignitions were reported in 155 mines and 13 states. Continuous miners represented the largest source for frictional ignitions with 1090 (68.6% of all frictional ignitions). Longwall mining operations represented the highest concentration of frictional ignitions during this study period with 1365 frictional ignitions (85.9% of all frictional ignitions). The 17 mines with the most frictional ignitions were all longwall mining operations and had 1130 frictional ignitions (307 from the shearer) that represented 71.1% of the total. In 1983, mines with frictional ignitions represented 6.9% of operating underground mines and 36.6% of total underground coal production. The percentage of operating underground mines with frictional ignitions and their total production has increased steadily and in 2005 represented 9.8% of active mines and 46.2% of underground coal production. The three coalbeds with the highest number of frictional ignitions (Blue Creek, Pittsburgh No 8, and Pocahontas No 3) had 1049 ignitions that represented 66.0% of all frictional ignitions. The three states with the highest number of frictional ignitions were Alabama (710), Virginia (247), and Pennsylvania (242) that represented 75.5% of the total. Frictional ignitions peaked in 1991 with a high of 114. In 2005, only 34 frictional ignitions were reported. If only frictional ignitions that occur at the face are considered, there have been no fatalities since 1983. Since this time, there were 33 ignitions that caused 53 workers to lose a total of 2912 working days. When including ground falls, then there have been four frictional ignitions with one incident causing two fatalities and injuring eight workers. From 1983-1991, underground productivity and the number of frictional ignitions increased. However, productivity continued to increase from 1991-2000 while total frictional ignitions fell, thereby disproving this connection between productivity and frequency of frictional ignitions. Ninety percent of all frictional ignitions occurred in underground coal mines that liberated more than 393 L/s (1.2 MMcfd million cubic feet per day) of methane through the main ventilation system. Although methane production is not the determining factor for the occurrence of frictional ignitions, it is a good indicator of the anticipated frequency.

The objective of this handbook is to provide the inspector with guidance for recognizing hazards from inhalation contaminants in above ground work areas of underground and surface coal mining and processing facilities and evaluating these hazards by collecting samples or making field determinations and interpreting the analytical results. There are several portions of the handbook which should prove most useful to the inspectors. The names and locations of these portions are listed below: Survey Check List (Page 2-3) Rules for Determining if Sampling is Required (Page 2-1) List of Most Frequently Encountered Contaminants (Page 2-2) List of Candidate Contaminants and their Sampling Conditions (Table 2, Starting on page 2-5) Interpretation of Results (Page 2-16) Procedure for a, Health and Safety Inspection (Page 2-25) For obtaining information not available from the above mentioned portions of the handbook, the inspector is directed to the Table of Contents, the Glossary of Terms, and the List of Commercial Products Encountered in Surveys.

Jan 1, 1975

This study estimates costs of producing bituminous coal and lignite by strip-mining methods in 12 hypothetical mines. Basic costs are developed by geographic area, rank of coal, and output capacity. Seam thickness and depth and type of overburden are considered typical for the area in which the hypothetical mine would be located. The cost analyses are based on the use of new equipment, the prevailing union wage scales, and the payment of all miscellaneous costs including royalties, contributions to the miners' welfare fund, and license and permit fees. All model mines are considered to have a life span of 20 years. Capital costs of bituminous strip mines with a capacity of 1 million tons per year range from $12.7 million in the Appalachian region to $16.0 million in the Interior province. The corresponding selling price, assuming a discounted cash flow return of 12 percent on investment, is $5.40 and $6.95 per ton, respectively. For bituminous coal strip mines producing 3 million tons annually, a capital investment of $24.9 million will render a selling price of, $3.46 per ton in the Interior province, whereas a similar mine in the Appalachian region requires a capital investment of $28.0 million to produce coal selling for $4.01 per ton. Subbituminous strip mines of 5 million tons of output per year range in capital costs from $28.7 million in the Southwest to $13.9 million in Wyoming and Montana. Coal produced in the Southwest would sell for $3.03 per ton, while coal from Wyoming and Montana would sell for $1.83 and $1.64 per ton, respectively. The capital costs for the strip mining of lignite range from $6.4 million for an output capacity of 1 million tons annually to $20.7 million for an annual capacity of 5 million tons. The corresponding selling prices of $3.01 and $2.12 per ton, respectively, Indicate the advantages of a large-capacity strip mine.

Jan 1, 1972

By William E. Young

There are many large rhodonite-bearing veins containing manganese in the Eureka-Animas Forks area of the San Juan Mountains in Colorado. The Sunnyside vein is the largest known vein in the area. As observed on the surface, the vein is mineralized over 8,000 feet and attains a maximum width of 200 feet. The average width of the vein and its branches and ramifications is 58 feet in the area that was mapped in detail. The weighted-average analysis of surface and underground samples from the northeastern extension of the Sunnyside vein is 8 percent manganese. Most other known veins in the area have a similar manganese content. The Hidden Treasure vein lies southeast of the Sunnyside-No Name-Mastadon vein. The weighted average of the analyses of surface and underground samples from this vein is 13 percent manganese. Exposures of the Scotia-Silver Chord vein are visible over a strike length of 4,000 feet on Treasure Mountain. Diamond-drill holes show that the vein contains 10 percent or more manganese to a depth of 400 feet. The vein has an average width of 28 feet. The Independence vein is exposed on the surface for a distance of 600 feet and has an average width of 6 feet. Three cut samples taken across the vein had an average content of 20.7 percent manganese. Sampling of the outcrops of eight veins in the Placer Gulch area also indicates manganese. Numerous other veins cropping out in the surrounding area are similar to the outcrop of the Sunnyside vein system mineralogically and are worth investigating.

Jan 1, 1966

By W. W. Aljoe

The use of protective canopies can result in canopy roofing and/or serious restrictions to operator comfort and vision. To document this experience, BCR conducted a field study of cab and canopy design and application which resulted in a catalog of 164 canopy designs and an analysis of field data which showed no simple relationship between working height and canopy-related problems. The relationship also involves (1) machine frame height, (2) mine floor undulations, (3) operator compartment dimensions, (4) canopy design and location on the machine. Data analysis indicates (1) present technology does not always permit successful application of canopies in working heights below 42 inches, and (2) development of satisfactory low-coal canopies is doubtful. The basic conclusion of the study is that future R&D studies should be directed at development of alternative protection systems and remote mining methods.

Jan 1, 1981

By Robert D. Perry

This report describes methods of reclaiming abandoned or inactive tailings ponds and dams. The investigated sites were selected tailings deposits adjacent to metal mines in the southwestern United States and the Pacific Northwest. The basic data developed for each site consisted of the following: a review of existing literature: a site visit that included sampling of the tailings and surrounding materials; laboratory and engineering studies; and development of reclamation plans. Laboratory tests determined the gold and silver content of each tailings deposit and the chemistry of the tailings and surrounding materials. Reclamation plans that include approximate costs were developed for five tailings deposit sites. These ranged in size from 52,000 to 103,000,000 tons. Our conclusions on the remining potential of each site are based on the tailings assay and other technical data. This study concludes that remining as a reclamation tool is feasible at certain sites. Included in this report is a remining program as part of the overall reclamation plan for two sites. Our preliminary results indicate that remining as a reclamation tool is feasible for only one of them.

Jan 1, 1981

By S. J. Broderick

[Huge camp heaps coat. in-.n,- ta._ur nd o tons of coal :'efuse are a familiar sight in coa).--:1'_ni`l ; res io The;;' repre£e: t considerable economic loss, are very ~JZ':Si~i,tly, and tr:_ e u.: mach v lua-ble :price. Consequentl;;* their remcva7. is ,-,reatl:r de sir^~t~ a_." ar return that c,-u? be obtained would. be especially rel.co c to the coal T,-e "a_ste nat(~ria1 commrioes large pieces of bore cca1., lumps rf c12;', -)nd finer refuc3 coming from the 'acxcor~-, Tnc e'-:s: rr;I refuso contains some Food coal. Th1S coal and the better crams of _,)ore Pre t'--:e na.torials considered. in ohis in¬vestigotion. T'.-.r, heavier fractions of the vas ier,,refuse a rd. the large pieces of slate a n i roc _r contain little carbcnacaous r..aterinl -.nd axe ~vir¬ tually worthless ra'., :,atcria1. for activated carbon. In the E i 1i 11?'ar 1 dictrict~ n1ab a :1 ut irfl percent of the' coal mined is wa^,hed., and in district rc_a e -c-cnuatcs at the r..-ate of I to 2 Million tons a year?]

Jan 1, 1941

By Bill Linville

During fiscal years 1967-68, the Bureau of Mines produced 185 technical papers and reports about petroleum and oil-shale research, which were published either by the Bureau or by others as referable scientific literature. Numerous other reports were prepared for Government agencies, State agencies, and organizations of the petroleum and natural gas industry engaged in cooperative research programs with the Bureau. Research performed during the reporting period by the Bureau on petroleum, natural gas, and oil shale was classified by 71 active projects. A basic appropriation of $3,575,000 was supplemented by $1,300,000 in fiscal year 1967, and that of $4,043,000 by $1,402,000 in fiscal year 1968, making the appropriated-to-supplemental fund ratios about 2.8 to 1 for fiscal year 1967 and 2.9 to 1 for fiscal year 1968. In fulfillment of the mission of the Bureau, through planned research programs, methods for producing and utilizing petroleum were improved. The continued conservation of this natural resource of petroleum, including crude oil, natural gas, and oil shale, was pursued through research performed by some 350 personnel at two petroleum research centers and two petroleum research laboratories supervised and supported by administrative personnel of the Bureau and the Department of the Interior.

Jan 1, 1970

By P. -É. Boileau, M. Smets, T. Eger, J. Boutin

Long-haul dump (LHD) vehicles used in underground mining are known to expose workers to important levels of whole-body vibration1. These vehicles are generally designed without suspension and may be categorized as small or large LHDs depending on whether their respective load capacities are lower or larger than 3.5 cubic yards. While the majority of older vehicles are equipped with a rigid or unsuspended seat, more recent LHDs often incorporate a suspension seat. The objective of this study was to define the vibration spectral characteristics of most commonly encountered large and small LHD vehicles operating in mining operations. This was done in an effort to categorize the vehicles in terms of vibration spectral classes to be reproduced on a laboratory whole-body vibration simulator to assess the vibration attenuation performance of a typical LHD suspension seat. Methods Vertical vibration measured at the seat attachment point of 8 small and 8 large LHD vehicles operating underground in typical mining operations under loaded and unloaded conditions was considered as the basis for defining the spectral classes. By regrouping the data collected for each LHD vehicle size and load condition, the overall distribution of acceleration power spectral density (PSD) of measured floor vibration was determined over the 0.5 to 20 Hz frequency range. Mean and envelopes of maximum and minimum values of PSD spectra were computed to define the spectral classes, along with the corresponding values of frequency weighted rms acceleration determined in accordance to the ISO 2631-1 standard2. These spectra were further used to calculate the displacements needed to drive a whole-body vibration simulator consisting of a platform supported by two servo-hydraulic actuators having a total stroke of ±100 mm. For validation purposes, the vibration acceleration spectra measured on the simulator were compared with the target spectra representing the spectral classes. Finally, the vibration transmissibility characteristics of a typical suspension seat were determined under sine sweep excitation using both a rigid mass load and a human subject having a mass of 62 kg and 85 kg, respectively. The SEAT value, representing the ratio of seat to base frequency-weighted rms acceleration, was further measured under each of the defined LHD vibration spectral classes by loading the seat with an 85 kg subject. Tests were repeated three times and the mean SEAT values were determined to assess the seat’s ability to reduce exposure to whole-body vibration in LHD vehicles. Results Three spectral classes applicable to both loaded and unloaded conditions were defined as shown in Figure 1: one for large and two for small LHDs. The influence of load on frequency-weighted rms acceleration was found to be negligible for large and Class I small LHDs, while a shift of the peak acceleration PSD to lower frequencies was noted for the loaded vehicles. The influence of load was found to be more important for Class II small LHDs. Table 1 provides a

Jan 6, 2006

By W. L. Dare

Tri-axial strains in pillars, created by pillar robbing, were measured in an experiment at the Dysart No. 1 uranium mine near Grants) New Mexico. At this mine, room-and-pillar stoping is used on the advance, and pillars are recovered on the retreat. The are deposit is, for all practical purposes, horizontal. Measuring devices were installed in pillars approximately 90 to 200 feet from the break line, and strains were recorded over a 4-to 6-week period. The measurements indicate that, in general, the algebraic magnitude of vertical strains increased, and the horizontal strains decreased, in turn, indicating that vertical (or near vertical) loads on the instrumented pillars lessened as pillars were recovered.

Jan 1, 1962

By Stanley C. Rhoads

The Bureau of Mines investigated the complete ternary system K2 HfF6¬K2ZrF6-l.25 weight-percent HF at 40° C. In addition, solubility curves have been established at 25°, 30°, 500, 60°, and 70° C. These solubility data implemented a study of hafnium enrichment in feed solutions for liquid-liquid extraction processes.. Selected K2HfF6-K2 ZrF6-1.25 weight-percent HF mixtures were equilibrated in a constant temperature bath. Compositions of the equilibrated solutions and wet residues were established from combined hafnium and zirconium oxide and total fluorine analyses. All solubility curves were essentially parallel on triangular coordinates. At 40° C, the solid phase of the K2HfF6-K2ZrF6-1.25 percent HF system is a series of solid solution hydrates with K2HfF6-H20 and K2ZrF6.3H2O segments existing at the respective extremes. Since this system contains K2HfF6-H20 and K2ZrF6.3H20 segments, it is not ideal for simple separation of high-purity K2HfF6 from K2HfF6-K2ZrF6 mixtures by recrystallization. However, it would be useful for producing hafnium-enriched feed solutions from zircon concentrates for liquid-liquid extraction of hafnium from zirconium.

Jan 1, 1973

By H. G. Wolfhard

The propagation of explosions through short cylindrical channels has been investigated by the Bureau of Mines. In the experimental apparatus set up by the Bureau, a single such channel formed a connection between a small explosion vessel in which a gaseous explosion was initiated and a larger, partly enclosing, explosion vessel filled with suitable gaseous mixtures; the larger vessel permitted observation to determine if an explosion was induced therein by mass, energy, and species transfer through the channel, as a result of tie initial explosion, It has been found that transmission of flame through to channel is not an essential to induce the second explosion, for hot gases from an extinguished explosion are able to ignite cold combustible mixtures in the larger vessel. The schlieren patterns of flames or hot burned gases emerging from a channel into the explosion chamber were photographed. These show, in most instances, that vortexes of hot gas ejected from the jet into the cold explosive mixture are responsible for ignition. The study has practical significance in problems of rendering electrical equipment safe for use in potentially flammable atmospheres, INTRODUCTION The propagation of flames through cylindrical or annular channels has practical importance in flameproofing electrical equipment and for flame traps. Much practical work has been done to determine the minimum safe breadth of flanges and the maximum safe gap between the flanges that will permit venting an electric motor without allowing flames to pass.

Jan 1, 1959

By Michael Kaplan

An investigation was conducted of the use of a mechanical rock splitter as the primary means for rock fragmentation in underground hard rock mining systems. Analyses and scale model tests showed that reasonably sized splitters that could be mounted on the booms of conventional drill jumbos were capable of fragmenting over a ton of rock per cycle. Detailed drill-split mining systems were developed for entry development, room and pillar, bench mining, and cut and fill mining. Economic analyses of these systems showed them to be generally competitive with conventional drill-blast methods. Except for bench mining, drill-split offered substantial cost savings over drill-blast. The investigation also included a technical evaluation of the mechanical splitter, an analysis of health and safety, and a determination of the potential applicability of drilling and splitting.

Jan 1, 1979

By R. P. Vinson

Assessment of workplace exposures is an important tool for helping to minimize dust-related occupational illness and diseases. Real-time particulate monitoring can effectively locate areas where dust controls are needed and determine how well they are working. An affordable, person-wearable, real-time dust monitor is needed. The SKC Inc. Dust Detective (SKCDD) fulfills those requirements (Disclaimer: Mention of any company or product does not imply endorsement by NIOSH). The SKCDD consists of a disposable sampling tube (DST) connected to a small hand-held sampling pump. The SKCDD was developed through a Cooperative Research and Development Agreement (CRADA) between the National Institute of Occupational Safety and Health (NIOSH) and SKC Inc. The relationship of dust concentrations measured by personal gravimetric samplers to those measured by the SKCDD was determined in a laboratory aerosol chamber. A comparison of the means and the relative standard deviation of triplicate measurements of each type of sampling device demonstrated the SKCDD to be a viable alternative means for measuring dust. While it provides accurate measurements for specific coal types, it requires correction factors (those correction factors still need to be calculated) for other coal types.

By Walter W. Fisher

A study of copper cementation on iron was initiated to determine the effect that deposited copper has upon subsequent cementation. A microscopic investigation of cementation on an iron surface showed that cupric ion precipitates predominately on a growing copper deposit attached to the iron surface. A kinetic study of the cementation process in a revolving drum showed that the cementation rate is enhanced by the copper deposit attached to the iron surface and by the discrete copper particles of a cement copper slurry. The kinetic study also indicated that the character of the deposit is affected by the major anion in the solution. The cementation process is visualized to occur as a series of electrochemical cells in which cupric ion precipitates on copper dendrites attached to the iron surface.

Jan 1, 1973

By H. E. Peterson

Rhenium occurs in very small quantities (12).4 In order for the Federal Bureau of Mines to conduct an investigation of rhenium sources and methods of extraction, it was necessary to devise improved techniques for detecting and measuring minute quantities of the metal. A modification of the procedure of Malouf and White (46) was developed which can be used to detect rhenium in concentrations as small as 0.1 part per million and can be used to measure quantities of 1.0 part per million. It can be used for the analysis of siliceous and calcareous ores, of molybdenite concentrates, of fumes, of flue dusts, and of other metallurgical products. Development of the method involved devising an amine extraction procedure for separating rhenium from all interfering elements except tungsten and a selective distillation procedure for separating rhenium from tungsten. Adoption of these separation procedures permits use of large samples and precise determination of rhenium by colorimetric analysis of the thiocyanate complex of rhenium by means of a spectrophotometer.

Jan 1, 1961

To improve communications between mine workings and surface locations during emergency situations and for administrative purposes. The Approach: Development of a device for interconnecting phone systems which permits two-way communication between a public telephone and a mine pagerphone by authorized personnel. How It Works: The system, developed by personnel at the Bureau's Pittsburgh (Pa.) Mining and Safety Research Center, makes connections between the public phone line and mine pagerphone line. As shown in Fig. 1., incoming calls are sensed by the ring detector (4) and the system "answers" the call electronically. To reach the pagerphone system, the caller inserts an audible tone of fixed frequency through the microphone of his telephone. This tone is produced by a miniature, pocket-carried tone generator and is detected by a tone recognition circuit (5). When this hap-pens, relay, switching, and logic circuitry (6) closes the connections between the two phone systems. Simultaneously, a page activator (9) places a DC paging voltage on the mine phone line.

Jan 1, 1974

By Charles F. Jackson

Gold mining is a subject that not only appeals to the popular imagination but has vital importance to the world's economic structure. However, a discussion of the use of gold as a medium of exchange, and a basis for credit between nations and for monetary systems is not within the scope of this paper. The importance of gold in carrying on the commerce of the world, the present supply and rate of production, the probable trend of future production, the probable future requirements, and related subjects have recently received much attention from bankers and economists, and many articles on these subjects have been published. During slack periods of base-metal production due to falling prices, accompanied by scaling down of base-metal mining operations and often by the closing down of at least some mines, there usually result revival of interest in gold mining, search for previously undiscovered deposits, and reopening of some old gold mines.

Jan 1, 1932

The contract for the Water Jet Chock Mounted Miner Feasibility Study was awarded to FMC Corporation's Advanced Products Division on 18 November, 1974. The program was divided into four phases as follows: ? Phase I - Planning ? Phase II - Conceptual Design ? Phase III - Budgetary Cost Estimate and Economic Feasibility Study ? Phase IV - Final Report During Phase I, which lasted 1 month, most of the necessary information and data for the conduct of Phase II was obtained. To accomplish this, arrangements were made for personal visits to the University of Missouri at Rolla, Illinois Institute of Technology Research Institute, USBM TCMRC, Alpine Equipment Co., Mining Progress, Inc. and Eastern Associated Coal Corporation's Harris No. 1 Mine. Also, a list of manufacturers of high pressure equipment was compiled to be contacted during Phase II. Finally, the objectives to be accomplished during Phase II were outlined. The Phase I Report was submitted on 23 December, 1974. At the beginning of Phase II, personal visits were made to the research centers and firms mentioned above. Later an additional visit was made to the Harris Mine, and to the Pittsburgh Mining Research Center at Brucetun to observe a test of a water jet mounted on an Alpine Mining Machine. Equipment manufacturers of high pressure components such as hoses, tubing, valves, pumps, and intensifiers were contacted to obtain item performance data, availability, and cost.

Jan 1, 1975