Search Documents

By R. Immele-Meziou, G. J. Long, D. G. C. Robertson, O. A. Pringle

The reduction of naturally weathered ilmenite concentrate occurs in two steps: reduction of Fe3+ to Fe2+, followed by reduction of Fe2+ to Fe. Small amounts of a magnetic phase were also observed and may correspond either to an Fe3O4-FeTiO3 ilmenite phase or to an Fe3O4-Fe2TiO4 spinel phase. The total amount of metallic iron produced after 12 hr was only 50% of the total iron present in the sample.

Jan 4, 1992

By Fearnsides W. G.

Discussion at the The Midland Institute of Mining, Civil and Mechanical Engineers' general meeting held in Doncaster on 27th May 1916, on the paper published in Trans. I.Min.E., vol.LI, 1916, p.409-448, included oral contributions by Lupton A. on the mechanisms of subsidence and water egress and by Kendall P.F. on the validity and accuracy of the contour extrapolation technique and the effect of major faults, together with the author's response

Dec 1, 1916

By Groom P.

The wastage of timber in coal-mines that is caused by decay is very great; in fact, far greater in this country than is generally realized. Mr. E. W. Peters estimates that of the whole wastage of timber in mines in the United States of America, 50 per cent, is due to decay and insects; of this 50 per cent, an overwhelming part is due to decay. The most efficient methods of decreasing this grave loss can be devised only by co-operation of the mining engineer and the scientific expert, and it is partly in the hope of procuring such collaboration that this paper is written. It contains, therefore, a resume of our present knowledge of the decay of wood, and of the economic methods of checking this in mines; but, with a view to improving those methods, it also directs attention to the gaps in our knowledge and the means by which these can be filled by future investigation

Dec 1, 1916

By N. A. Warner, R. K. Manna

Physical modelling of liquid-phase oxygen mass transfer in a water model of part of a proposed new polymetallic smelter has been achieved. A study of solute mass transfer caused by multiple, subsonic air jets contacting superoxygenated water flowing in a channel model of the smelter converting hearth has been carried out. For a wide range of channel flow rates the rate of mass transfer was found to be independent of water velocity. The water model has been used to compare mass transfer for both open-packed and close-packed multiple-lance arrays with circular nozzles of diameters 2.26, 4.95, 10.95 and 24.40 mm. It was found that with fewer of the larger-diameter nozzles a reduction of up to 58% in liquid-phase mass transfer occurred, especially for the close-packed lance configurations. This restriction of liquid-phase mass transfer would result in reduced metal losses in the analogous smelting situation. The larger nozzles, however, exhibited more jet-jet and jet-channel wall interference effects than their smaller counterparts, resulting in an effective reduction in the momentum fluxes of the impinging jets

Jul 1, 1991

By C. H. J. Beaven, M. P. Jones

Since the various new techniques of automation and computing have enabled vast numbers of mineralogical observations of relatively small samples to be made cheaply and rapidly, the statistical assessment of these measurements has become of vital importance. Much of the theory and most of the procedures of sampling that are used in the mineral industry are based on Gaussian statistics, but modern measuring techniques show that many mineralogical parameters do not necessarily follow the Gaussian distribution function. Consequently, it has become necessary to examine the application of other, more suitable statistical methods in order to derive the maximum amount of useful information from the examination of mineralogical samples. Some of the errors that can be introduced by the use of incorrect distribution functions are discussed and the value of determining the function that is appropriate to the particular parameter that is being measured is shown. Examples are provided of non-Gaussian distribution functions in mineralogical materials that were encountered during prospecting and during mineral treatment operations: a Canadian uranium ore, a Thai tin ore, and gold ore tailings.

Dec 1, 1971

By R. R. Hart, R. A. Evans

This paper outlines the the methods currently being used in the West Wales Area for preventing the occurrence of any outbreak of spontaneous combustion. Stress is placed on the importance of correlating the position of a Rider Seam which is prone to spontaneous combustion. The recent introduction of the UNOR Recorder has contributed to the ability to monitor the CO content of the general body of the air during any incident. The use of modern sealants and improved methods of applying them have enabled the few instances of spontaneous combustion in South Wales to be treated promptly and efficiently. The authors describe the current spontaneous combustion problems at two collieries.

May 23, 1905

By A. Z. Lang, D. A. Hall

After a brief description of the causes of spontaneous heating and of general preventative methods, a detailed account is given of occurrences of spontaneous heating in the Main Seam (locally known as the 5/4 Seam) at Westoe Colliery. This seam is about 12 feet thick consisting of hands of coal and shale, but only 4 feet 6 inches is worked because of the thickness os strata in water-bearing rocks and the worked section is selected on quality considerations. An advancing longwall face in this seam (2nd South) began to heat after working for six months and ultimately had to be abandoned. By adopting retreating methods and mining narrow panels it has been possible to extract this coal at an excellent rate of productivity. The system of goaf ventilation is important, because the use of a bleed road would have given rise to dangerous conditions in a goaf which of necessity would have contained fallen coal. Preparatory seals were prepared at selected sites so that, if necessary, a panel could be sealed off quickly; these seals are completed as soon as possible (within three weeks) of finishing a panel. A gas sampling system has been instituted which includes daily sampling on the face and in the goaf, and weekly sampling at the stoppings of all completed panels. The coal has now been extracted from this seam for three years without any further difficulties from spontaneous heating.

May 23, 1905

By R. I. Jeffery, J. W. Summers

An account is given of the verification and calibration of a numerical modelling technique that has been developed for the prediction of subsurface strata deformation following the extraction of coal by longwall mining methods.

Jan 4, 1992

By D. J. Reddish, B. N. Whittaker, G. X. Sun

An image analysis technique has been used in the assessment of subsurface fracture levels in the context of water inflow into longwall mine workings. The technique was used to analyse results from physical modelling which are represented by black and white photographs taken directly from the model tests. Binary images of fracture patterns are obtained by scanning the photographs with an image analyser coupled to a video camera. The images are manipulated by a C program which allows them to be processed in vertical and horizontal directions and filtered to differentiate quantitatively between vertical and horizontal fracture intensities. The fracture density distributions provide a valuable database for further numerical and statistical analysis. This allows assessment in terms of water inflow into the excavation. A comprehensive image analysis was undertaken on several extraction models. Results indicate that extraction thickness has a significant effect on the fracture pattern and the fracture density distributions. The results can be used to adapt model findings to situations with a range of extraction thicknesses. The technique has allowed improvement in image enhancement and in the interpretation of model results. In particular, a qualitative comparison between different models is possible.

Jan 12, 1992

By R. G. Siddall, W. Gale

In the UK the development of the science of strata control has been strengthened by a resurgence of interest in the specialism of roofbolting and its associated techniques. The evolution of the theories and practices of strata bolting in roadway stabilisation is discussed. Practical experiences are considered, principally the use of Australian techniques, the relationship between bond strength and annulus and the effects of stress in the ground. Areas of new technology such as cable bolting, injection anchors and on-board bolters are also discussed. The recent advances in computer technology and rock testing equipment and methods have provided the opportunity to simulate ground behaviour under various conditions. Computer modelling developments and the use of techniques to predict ground behaviour are described.

Jan 4, 1992

By R. R. Liebenberg, M. I. Brittan

The kinetics of the copper segregation process has been investigated. The experimental strategy used to isolate the rate-controlling reaction step is described. This step was found to be the chloridisation of the oxide copper minerals in the ore. The link between the rate of chloridisation and the overall rate of segregation is demonstrated experimentally. The influence on the kinetics of the various parameters in a TORCO system is examined and the implications are discussed

Dec 1, 1971

By Z. H. Khan, A. K. Saha, D. D. Akerkar

The possibility of extracting nickel from a low-iron, highly siliceous nickel ore of Indian origin using roast reduction followed by an ammonia leaching process has been examined. The ore used in the investigation contained 0.82 wt% Ni, 6.20 wt% Fe3O4, 12.04 wt% MgO and 60 wt% SiO2. Phase changes in the constituent minerals on heating were studied by differential thermal analysis which revealed endothermic peaks at 110 and 695 degrees C and an exothermic peak at 810 degrees C. Significant process variables in studies of roast reduction include the amount of reductant, the temperature of reduction and chemical kinetics. Maximum nickel extraction was achieved by reducing the ore with 10 wt% fuel oil at 750 degrees C. The reduced ore was given a preconditioning treatment in concentrated ammonium hydroxide solution to oxidise most of the metallic iron and was then leached in aqueous ammoniacal solution at ambient temperature to dissolve nickel. This gives 88.5% extraction of nickel as soluble ammine complexes.

Jan 4, 1992

By L Zhang

The Chinese coal industry is the largest coal producer in the world. The total production in I995 was 1.28 bnt. On the way towards introducing a market economic system, this mature industry is facing major challenges. The main problems are a large surplus of manpower, shortage of current assets and capital, low productivity, high casualties and a huge deficit. This paper discusses the present situation and the future developments in the Chinese coal industry. The current policy can be stated as ‘rapidly developing the state collieries and improving the village and private mines; integrated development to achieve an economic operating scale and encouraging a diversified economy; rapidly exploiting and developing in the North west and South west; promoting productivity and efficiency; welcoming multi-sources and types of investment; setting up coal exchange markets; and the careful control of resources and the environment'.

Jan 11, 1996

Jan 1, 1947

By G. D. Nicholls

There have been very few attempts to isolate the various factors that contribute to the overall imprecision of geochemical analytical procedures, due in part to the difficulty of distinguishing between them. The technique of spark source mass spectrography permits a ready distinction between the contributions to overall precision from sampling error and instrumental and other errors. With conventional methods of sample preparation for this technique sampling difficulties are responsible for 80-90 per cent of the overall imprecision. Examination of the probable location of the major difficulties in sample preparation indicates that the preliminary stage of grinding, mixing and extraction of a first aliquot (about 1/100 of the original sample) is generally perfectly adequate. The difficulty lies in the subsequent stages of sample preparation. Dry mixing techniques are unlikely to give good precision if the sub-samples actually examined by the analytical technique are less than 10 mg in amount. Solution techniques are less prone to sampling difficulty. Fusion techniques, unless conducted with great care, can produce more difficulty than dry mixing. Sample preparation is critical to the success of many analytical procedures. Selection of appropriate sample preparation techniques requires just as much care as the selection of techniques for the actual analysis.

Dec 1, 1971

By R. J. Bridges

Mining operations on the Witwatersrand are conducted for the most part in rocks of highly quartzitic character. They comprise the following types: Conglomerates, grits, and quartzites, to which on the Far East Rand must be added fine-grained quartzitic shales and shales. In addition, vein quartz occurring as small veins, veinlets and fissure fillings, and igneous rocks forming dykes, must be mentioned, although they constitute only a small percentage of the rock broken. The following is an account of the character and mineralogical composition of the various types.

Jan 1, 1947

Discussion of the papers with a written contribution and authors' written replies.

Jan 1, 1947

By T. Piirainen, T. Alapieti

"The Koillismaa layered igneous complex is the result of igneous activity that occurred 2436±5 m.y. ago. Its crystallization took place in three separate but connected magma chambers, the total volume of which is estimated at more than 2000 km'. These chambers were located partly in a feeder system within Archaean granitoids and partly in an unconformity between these grani­ toids and Early Proterozoic supracrustal rocks. The composition of the parental magma that initially filled the chambers is thought to have been that of a relatively MgO-rich tholeiite. Sulphides and platinum-group minerals are mainly concentrated in the marginal series of the western part, where they are encountered over a distance of 25 km. This marginal series is an originally nearly horizontal series of rock types that displays a reversed differentiation trend, grading inwards from gabbroic to ultramafic rocks, followed bv rocks of the layered series. The chilled margin is not encountered anywhere in its original position at the contact, probably as a consequence of magmatic erosion, but remnants are to be found in the form of elongated xenoliths. Partly melted siliceous fragments from gneissic country rock typical of the lower part of the marginal series indicate pronounced contamination.Chalcopyrite, pentlandite and pyrrhotite±pyrite are the predominant sulphides. The accessory sulphide minerals include covellite, violarite, marcasite, mackinawite, sphalerite and argentian pentlandite. Platinum-group minerals are represented by froodite, michenerite, merenskyite and sperrylite. Other accessories that have been identified are electrum and native copper and gold. The mean of the Cu/(Cu+Ni) ratio in the mineralizations is 0.67 and Pt/(Pt+Pd) 0.31.It is suggested that the sulphide phase was formed in the marginal series as the solubility of sulphur in the basic magma was lowered by contamination, possibly assisted by some other factors. The sulphur isotope data support the juvenile origin of the sulphur."

Jan 1, 1984

By G. J. Lyman

Mayer curves are used for process calculation in coal preparation. They can also be used to smooth washability data by fitting a hyperbola of particular properties to ash and yield, but to introduce the density variable an independent relationship with ash content must be adopted. When this ash-density relationship has a realistic form at low density, the implied form of the mass distribution function is unrealistic, suggesting that Mayer curves represented by a hyperbolic functional form are unsuited to coal washery calculations for low-density separations. Their use at higher densities is also uncertain. A similar conclusion can be anticipated when Mayer curves are used for other mineral systems.

Jan 8, 1992

By D. G. Skinner, J. H. Griffiths, F. T. Williams, A. G. Withers

"The absence of homogeneity, in dust-clouds underground indicates the use of a method in which the volume of air sampled is an appreciable proportion of the total volume under consideration. Of the available methods, only the impinger and gravimetric techniques seem to comply with this requirement. In practice, greater efficiency of collection of the smaller particles is possible by the use of a gravimetric filter than with the impinger. For this reason if, as seems desirable, a standard method of sampling be sought, the adoption of a gravimetric technique is to be recommended.Provided that the amount of dust collected is reasonably large, the paper filter would seem to be preferable to the solid crystal type of filter on account of its greater convenience in use.Alternative methods of sampling are desirable to cover the wide range of practical conditions."

Jan 1, 1947