Search Documents

By Özcan Y. Gülsoy

Coal beneficiation with optical sorting has not yet been studied in detail. Optical separation of coal from gangue particles as a dry method can be used as an alternative to the other enrichment methods. Developments in optical and pneumatic technology put the optical sorting one step forward by means of applicability of the mechanical sorting to the mineral industry. Because of the inefficient separation performance, dry separation of coal is very limited in industrial applications. Therefore, optical sorting depending on color differences between two minerals can be introduced to coal beneficiation systems. In this study, coal samples obtained from Konya-Ilgin region (Central Anatolia-Turkey) were separated by optical sorter and the results were evaluated. The conventional floatability tests for Ilgin coal are conducted by collecting most of the feed material at 1.3-1.4 g/cm3 density range. Separation of Ilgin coals with heavy medium methods will not be possible because of poor density difference between coal and its impurities. There are important color differences among the floated particles at 1.3-1.4 g/cm3 density range. Therefore, Ilgin coal is subjected to optical sorting in a pilot scale optical sorter. Different size fractions were fed to the optical sorter and then rejected and accepted particles by equipment were analyzed. Ash content of the accepted particles was reduced to 25-35 % and ash in tail increases up to 55-60 % after sorting. Although most of the material floated at low densities, optical sorter separated the feed into two different quality products. This study has the potential to clarify applicability of optical sorting even to non-floatable coals and to provide an important contribution to both industrial applications and literature.

Sep 1, 2012

By Matveyeva Tamara

The main deposits of gold-sulfide ores of Russia are characterized as refractory raw material with the non-uniform finely-interspersed sulfide mineralization, submicron gold, the low gold content (3-5 ppm) and non-uniform distribution of the gold associated with pyrite and arsenopyrite. These ores show low indicators of extraction of gold and silver at cyanidation. Flotation is one of the basic technological procedures of processing of gold sulfide ores however simultaneous presence of pyrite and arsenopyrite and lack of effective methods of their selection constrains application possibility of flotation schemes because of rigid requirements to flotation concentrates under the arsenic content and practically excludes smelting of pyrite concentrate. The main losses of precious metals at flotation technologically are concentrated in thin classes (up to 15 %) demonstrating an inefficiency of standard reagent modes. For an estimation of expediency and possibility of application of selective flotation of pyrite and arsenopyrite a scientific substantiation of the mechanism and criteria of selection of gold-bearing ferrous sulfides of various material structure is developed and for difficultly divided pairs of sulfides with close technological properties the new selective reagents providing effective extraction of gold from hard-to-beneficiate ores are designed. The original technique for modifying surface composition of natural sulfides by nano-sized Au is worked out and the mechanism of selective adsorption of new reagents ? oxypropyl ester of diethyl-dithiocarbamatic acid (OPDTC) and oak bark extract (OBE) on Au-bearing sulfide minerals is revealed. Formation of almost insoluble OPDTC-Au compounds is defined by methods of scanning electronic microscopy (SEM) and UV-spectroscopy. Application of developed reagent modes using new reagents have been tested in laboratory conditions at flotation gold-sulfide ores samples and collective concentrate probes providing high extraction of gold and improved quality of the concentrate (less than 2 % As). Keywords: pyrite, arsenopyrite, selective flotation, flotation reagents adsorption, complex-forming, gold recovery.

Sep 1, 2012

By József Faitli, Barnabás Csoke, Károly Solymár, Zoltán Hatvani, Dimitri Papanastassiou

"Grinding has a significant economic impact on ore dressing/processing, therefore the sizing of mills has an outstanding role.In most cases, the sizing of dry or wet mills for ore processing is primarily based on the determination of the Bond grindability index, using the Bond-Kjos-Rowland relations. In several cases, grinding takes place under conditions different from these and the grinding conditions have a great influence on the post-grinding process. This is particularly true for the grinding of bauxites where grinding takes place in alkali, often in higher temperature (up to 100 ºC) in alkali Liquor. So it is necessary to develop a testing method providing a reliable grindability index even under these special circumstances (grinding in alkalis medium at different temperatures) and allowing a more precise mill sizing. The new heated mill is suitable to determine the grindability index under temperature-controlled circumstances, in liquids with different temperatures (water, alkali). This paper presents in detail the equipment, the conditions (parameters) of the testing process for wet and alkaline grinding, the measuring results and the conclusions."

Jan 1, 2003

By Hillary Williams, Ronghao Li, Christopher Marion, Kristian E. Waters, Devin Hundt

"Zircon is an important mineral for ceramic, foundry, casting, and refractory applications; and it is the worlds primary source for zirconium. Zircon can also contain large and valuable proportions of other valuable metals, such as rare earth elements and hafnium. The Nechalcho deposit (Northwest Territories, Canad), is a hard rock REE deposit, which looks to recover zircon for its Zr and REE content. In this deposit, zircon is finely disseminated and associated with predominately silicate gangue minerals. Most of the work to date has focused on the beneficiation of mineral sand deposit, which typically remove silicate gangue minerals through physical separation steps. Therefore, the separation of zircon from silicate gangue, such as quartz, by flotation, has received little attention. This work used zeta potential measurements and microflotation experiments to understand the interaction between zircon and six different collectors (sodium oleate, sodium dodecyl sulphate, dodecylamine, SM 15, K-octyl hydroxamate and Florrea 7510). The results were compared with those of quartz. This study indicated that selective separation of zircon from quartz without the use of selective depressants or activators is likely challenging. The findings suggested sodium oleate and SM 15 only offered selective flotation of zircon in highly acidic conditions. Separation by the flotation of quartz is possible using sodium dodecyl sulphate, dodecylamine and K-octylhydroxamate. However, selective separation is highly dependant on collector dosage, for dodecylamine, and the selective activation of quartz, for sodium dodecyl sulphate and K-octyl hydroximate. Florrea 7510 offered poor recoveries for both zircon and quartz.INTRODUCTIONZircon (ZrSiO2) is a nesosilicate mineral which has a wide variety of applications, due to its hardness, opaqueness and resistance to heat and corrosion. Its major end uses are in ceramic, foundry, casting, and refractory applications (Bedinger, 2017). Zircon is also the most abundant zirconium (Zr) bearing mineral in the earths crust and is the principal economic source of Zr (primarily used in alloys for heat and corrosion resistance) and zirconia (ZrO2) (primarily used in ceramics) (Bedinger, 2017; Milnes and Fitzpatrick, 1989). Zircon forms in silicate melts and can often contain large proportions of other valuable metals such as rare earth elements (REE), and hafnium (zircon is the primary source of hafnium) (Bedinger, 2017; Belousova et al., 2002; Orlova, 2007). A common chemical formula showing the range of substitution in zircon is (Zr,Hf,Th,U,REE,Ca,Fe,Nb,Ta)(Si,P)O4 (Orlova, 2007)."

Jan 1, 2018

By T. N. Matveeva, T. A. Ivanova

"The article presents the results of the research aimed at development and testing of new effective reagents – collectors and green modifiers for more complete extraction of gold and platinum to concentrates at reduced loss with waste products. The main deposits of Au and PGM ores of Russia and abroad are presented by refractory raw material with the non-uniform finely-interspersed sulfide mineralization, submicron gold and platinum, the low metal content, non-uniform distribution of valuable minerals. and show low indicators of recovery. The main losses of precious metals (up to 15 %) at flotation are associated with thin slam tailings because of inefficiency of standard reagent modes.In the paper, the new trends in design of collecting agents for extraction of gold and PGM sulfide minerals and their application in flotation tests are substantiated. The original technique for obtaining the modified collector reagents – dithiocarbamate, dithiophoshpinate and dithiazine, incorporated non-ionic compounds that are able to generate stable complexes with gold and platinum has been developed. A novel class of collectors – cloud point polymers showed high flotation recovery of fine particles of gold and platinum. The original technique to create the mineral samples of natural sulfides with ""invisible"" or sub-micron gold on their surface designed helped to indicate the mechanism of selective adsorption of novel agents on Au and Pt-sulfide minerals. Extractive UV spectrophotometry, potential measurements, X-ray phase and spectral analysis, scanning electronic microscopy (SEAM), laser SIM and AFM microscopy were applied to analyze the adsorbed layer of modified reagents on the mineral surface. Selective hydrophobic covering on the surface of micro- and nanoparticles of noble metals provided an increase in their extraction during flotation. New reagent modes of modified collectors and green modifiers were tested in scaled-up laboratory flotation and the results obtained demonstrated the increased quality of the concentrates in terms of gold content by 1.5 times and higher gold recovery by 1.5-5%. The studies have been supported by Grants of the President of RF “Scientific School of Academician Chanturiya” NSh-220.2012.5; NSh-748.2014.5."

Jan 1, 2018

By Yi-jun Cao, Jin-cai Ran, Guo-sheng Li, Jiong-tian Liu, Li-jun Deng, Shu-lei Li

A fly ash sample from a power station in Guangdong province has been characterized by size separation, X-ray diffraction, contact angle measurements and X-ray Fluorescence. The ash sample had a loss-on-ignition (LOI) (%) of 15.54% and a large proportion of the unburned carbon was distributed in the +74 µm and -20 µm fractions. Contact angle measurements suggested that the removal of unburned carbon from the fly ash using flotation would present some challenges. The effects of various operating variables on the removal rate of unburned carbon (RUC) (%) and (LOI) (%) were determined using a cyclonic-static micro bubble flotation column (FCSMC). Within the range studied, the optimum diesel oil dosage was 1200 g/t, abies oil (frother) dosage was 600 g/t, pulp density was 20%, superficial gas velocity was 1.4 cm/s and circulating pressure was 0.20Mpa. Column flotation tests indicated that the FCSMC method a viable and effective separation process for removing the unburned carbon from the fly ash. Under the optimized conditions, a clean ash with 2.13% LOI and 94.21% RUC was obtained.

Jan 1, 2014

By Tatyana A. Ivanova, Tamara N. Matveyeva, Anatoliy A. Fedorov, Tatyana V. Nedosekina, Valentin A. Chanturiya

An ingenious methodology purposively developed by the authors for comprehensive assessment of flotation properties, electrophysical characteristics and. crystal chemistry features of natural gold-bearing sulfide minerals of different origin has been used in this study. Examination of the elemental composition of the minerals, ion-molecular components of the liquid phase in suspensions, surface properties of sulfides and different flotation reagents sorption forms was performed using the methods of X-ray phase and spectral analysis, potentiometry, UV and IR spectrometry, computer image analysis, and computer simulation techniques. The role of isomorphous impurities in the formation of hydrophobic sulfhydric collector layers on mineral surfaces in complex ore processing has been elucidated. The parameters characterizing the variability of the Fe:S ratio in pyrite of different origin have been determined based on non-stoichiometry characteristics of natural gold-bearing sulfide crystals. An ingenious method of formatting and linear approximation of experimental data was used to find out the quantitative relationships between the impurity content, electrophysical characteristics, non-stoichiometry and floatability of pyrite from a number of different deposits. The effect of the impurity species present in sulfides on the characteristic pH value marking the floatability peaks as such and their trend of shift towards higher alkalinity has been revealed. A theoretical substantiation has been given to prognostic assessment criteria for processing characteristics of gold-bearing sulfide minerals with varying composition. New flotation reagents and advanced reagent systems which help to increase the contrast of processing characteristics for different gold-bearing sulfides, resulting in improved selectivity, have been developed. The mechanism of selective flotation of precious metal-bearing Fe and As sulfides achieved by using short-chain dithiocarbamates and a mixture of cyclic trithiocarbonate with oxyalkylsulfides has been analyzed.

Jan 1, 2003

By M. Kanuchová, J. Briancin, M. Achimovicová

"Faculty of Mining, Ecology, Process Control and Geotechnology, Technical University, Košice, Slovakia An industrial eccentric vibratory mill was used for direct and short-time mechanochemical reduction of ilmenite concentrate (FeTiO3) and anatase (TiO2) with magnesium metal powder in order to reduce Fe and Ti resp. and hereby to convert them to the more soluble phases suitable for further hydrometallurgical processing. X-ray diffraction analysis of FeTiO3 after 60 min of milling with Mg confirmed the presence of Fe0 and Mg2TiO4 phases and for TiO2 after 180 min of milling the new TiO and MgO phases have appeared. X-ray photoelectron spectroscopy has detected Fe0 (metal) and Mg2+ species which are corresponding to the product of FeTiO3 mechanochemical reduction. The product of TiO2 mechanochemical reduction has revealed XPS spectral lines corresponding to Ti2+, Ti4+ and Mg2+ species on its surface. Morphology of mechanochemically reduced samples was studied by scanning electron microscopy analysis. Subsequent leaching of mechanochemically reduced FeTiO3 and TiO2 was performed in dilute HCl and H2SO4 at 80oC and compared with mechanically activated samples. The recovery of Ti has reached 100% for FeTiO3 and 79% for TiO2 after 60 min of leaching. Based on this study the flowsheet for possible processing of natural refractory titanium ores patented by author was adapted and documented. INTRODUCTION Ilmenite (FeTiO3), along with rutile (TiO2) represents the most important titanium resource necessary for titanium industry, for production of titanium metal, alloys and pigment grade TiO2 which are becoming more important and versatile for various industries such as an aircraft and aerospace, navy, chemical, automotive, medical and offshore wind industries, for machine and plant engineering and architecture as well, mainly due to high corrosion resistance. Pigment grade TiO2 is utilizing in pigment, plastic, glass, paper and rubber industries (Zhang, 2011). There are obvious research efforts for development of the potential alternatives to the expensive thermo-chemical commercial processes of titanium raw materials processing. Zhang (2011) has summarized conventional thermo- a electrochemical processes which involved a combination of pyrometallurgical, hydrometallurgical and electrometallurgical technologies and highlighted the improved hydrometallurgical routes promising for commercial application in the future. Such improvement could also be mechanical activation of FeTiO3, TiO2 by high-energy milling which causes their structural disordering, the changes of physical and chemical properties, consequently and has a positive effect on the dissolution kinetics (Achimovicová et al., 2014a, 2017, Baláž, 2008). The various types of mills such as a planetary ball mill, a vertical ball mill, a drum mill, an attritor were used for mechanical activation of FeTiO3 as a pretreatment process for subsequent leaching (Achimovicová et al., 2014)."

Jan 1, 2018

By Vladimir F. Skorokhodov, Nikolay N. Melnikov, Svetlana P. Mesyats

"Among the problems of the civilization development, a problem of interaction between man and natural environment can be highlighted. In the twentieth century the human transforming activity had got scales of geological processes and defined the contradiction between the goal to increase the quality of human life and possibilities of the natural environment. Last twenty-five years after the World Summit on the Environment (1992) indicate that the development of civilization is still based on receiving super profits from the natural resources exploitation. This statement is confirmed by economy globalization rates, growing contradictions between consumption and production, depletion and degradation natural environment. A new technological order is formed at the time of growing world population, technological capacities, organizational complexity, from one side, and global scales of geo-resources consumption, on the other side. Sciences, determining the further civilization development, should take on the task to change the social worldview, since the preservation of human population consists in remediating and maintenance of biosphere functions as a regulator of ecological balance. The new worldview in the geo-resources exploitation is based on the Ecological strategy of mining development, which consists in reducing mining-induced loading on natural environment while increasing efficient mineral production and processing, and providing for a comprehensive solution of tasks on mineral deposit development. One of strategic trend of mining development is to increase complexity and completeness of useful component extraction from ore and mining deposits while reducing wastes and decreasing their stockpiled volumes. The implementation of the ecological strategy has shown that the future is determined by reduction of the environmental impact while improving the efficiency of mineral mining and processing.INTRODUCTION The global nature of environmental problems caused by the scale of consumption of natural resources, huge amounts of waste, and intensive man-made impact on the environment requires a revision of the strategy for the natural resources development. Many existing technologies are ineffective in achieving the ultimate goal. Direct output in the raw materials - the end product technological chain rarely exceeds 10%, which implies a huge amount of work to move the soil. In addition, the feature of scientific and technological progress at the present stage is the growth of power-to-weight ratio."

Jan 1, 2018

By D. J. Borrow, K. van Netten

"A fine coal tailings feed was selectively agglomerated using a concentrated water in oil emulsion binder consisting of 95% aqueous phase and 5% organic phase. The purpose of the study was to investigate a continuous system in plug flow, providing a rapid beneficiation technique with high selectivity and recovery. The development of the novel binder was undertaken in previous work in a batch system consisting of a high-speed blender. In this previous work, it was found that agglomeration could be achieved in 3 s, providing the binder was pre-dispersed. Furthermore, it was found that, depending on the feed, only ~1 wt% of oil was required to achieve agglomeration, some 10 times less than required in traditional oil agglomeration. In a more recent study, the technique was adapted into a continuous process. Due to the rapid speed of the process using the emulsion binder it was found that a simple flow constriction within a 1 inch pipe was sufficient to achieve the selective agglomeration observed in the batch system. In this previous study, a coal feed consisting of a flotation product was agglomerated at a superficial slurry velocity of 1.3 m/s using a partially closed ball valve as the flow constriction. In the current study, a feed consisting of fine coal tailings with an ash content of 50.1% was used to establish the influence of superficial slurry velocity on the agglomeration process. The superficial slurry velocity was varied between 1.3- 4.2 m/s, while maintaining a constant pressure drop of 100 kPa across the flow constriction. The flow constriction consisted of a partially closed ball valve. It was found that increasing the superficial slurry velocity across the flow constriction reduced the amount of organic liquid required to achieve agglomeration. Under the optimum conditions, a combustible recovery of 80.4% was achieved at a product ash content of 9.6%. This work demonstrates a valuable product can be rapidly produced from tailings material using the novel emulsion binder. INTRODUCTION A significant opportunity exists to recover fine coal from material that is currently classified as waste. This waste material, also called tailings, is currently considered not economic to process due to its high ash content, low solids concentration, and the fine size of the particles. Thus, for this opportunity to be realised, a process is required that is highly selective and has the ability to economically recover fine particles at high throughputs. The technique of oil agglomeration has previously been considered as a candidate for the recovery of fine coal, as it is highly selective and has no lower limit on the size of particle that can be recovered (Capes and Jonasson, 1989). However, the cost of the oil required as the binding agent in the process has proven to be a significant barrier to any long-term applications (Swanson, Nicol, and Bensley, 1977). Recently, however, Yoon and co-workers have developed an ultrafine coal separation process that utilizes an oil phase for the recovery of the hydrophobic coal particles and have implemented an oil recycle to greatly reduce the consumption and thus cost of the oil (Yoon et al., 2016)."

Jan 1, 2018

By A. Norori-McCormac

"Air recovery, the fraction of air entering a flotation cell that overflows the cell lip, is linked to flotation performance, and it has been shown through industrial testwork that operating flotation cells at air rates that yield the Peak Air Recovery (PAR) results in high mineral recovery. For operating parameters over which flotation plants have little control, such as particle size, investigating the effect on the position of PAR, and the subsequent effect on flotation performance, proves more challenging. To this end, we have developed a bench scale flotation system that runs continuously and exhibits froth behavior similar to that found industrially, allowing the study of such parameters as particle size in addition to air rate. The bench scale system comprises a 4 l baffled cylindrical flotation cell, stirred by a Rushton impeller. The concentrate is recycled back into the pulp, allowing for continuous operation. Glass beads are used as solid particles, allowing a wide range of particle sizes to be tested, with TTAB as collector and MIBC as frother. The system allows operation at air rates typical of industrial flotation systems (1 -2 cms-1 superficial gas velocity), in addition to yielding a froth that coalesces and bursts and exhibits a peak in air recovery as cell air rate in increased. Solids and water recovery is also measured. The results show that air recovery is sensitive to changes in particle size. The intermediate size distribution showed a peak in air recovery (PAR) that corresponded with the maximum solids flowrate, as found industrially. It is shown that finer particles do result in more stable froths and higher recoveries, particularly at low air rates. The effect of particle size on the position of PAR is not yet unequivocally determined from these results."

Jan 1, 2014

By Edgar Schach, Tom Leistner, Markus Buchmann, Urs A. Peuker, Martin Rudolph, Marius Kern

"In this study, the flotation characteristics of a cassiterite-bearing fine-grained and complex skarn ore from a deposit in the Ore Mountains is investigated. The tests are performed using an oil-assisted column flotation approach to process very fine ore fractions and avoid losses of cassiterite into the tailings. First, process parameters are obtained for a finely ground artificial mixture of quartz, magnetite and cassiterite, simulating the real ore. Thereby, magnetite is used, as iron oxides can have a detrimental effect on the flotation due to a similar flotation behavior. In addition, they can act as a source of multivalent ions, which are known to reduce the concentration of collector molecules, active for flotation. Based on the results, selected parameters are further tested for cassiterite skarn ore from the Hämmerlein deposit including a pre-conditioning and a water exchange step to remove ionic contaminants. The process response is analyzed in detail by XRF (X-ray fluorescence) and MLA (mineral liberation analysis) to get a better understanding of the behavior of the single ore components. Sulfosuccinamate type surfactant is utilized as the collector, emulsifier and to reduce the froth destabilization through nonpolar oil. Sodium hexafluorosilicate is added as the depressant.INTRODUCTION Complex skarn ore deposits containing considerable amounts of tin, indium and other metals are located in the Ore Mountains region (Germany). In this study, a skarn ore from the Hämmerlein deposit was investigated. Due to the finely disseminated nature of this ore, past beneficiation attempts failed, and the ore was considered economically unprocessable. However, increasing resource demands brings it back into focus (Schuppan and Hiller, 2012). Cassiterite is the main tin bearing mineral in this ore. Due to its high density (~7 g/cm³), the predominant beneficiation technique is gravity separation (Angadi et al., 2015). Tin ores from disseminated deposits have to be extensively comminuted to reach a sufficient degree of liberation of the cassiterite grains. As cassiterite has a brittle nature, it is preferable enriched in small size fractions, during comminution (Angadi et al., 2015). Gravity separation methods become more and more inefficient for particles smaller 40 µm (Falcon, 1982), causing tin losses of up to 30 to 40wt.-% (Angadi et al., 2015). Thus, froth flotation of cassiterite was first utilized in Altenberg in the Ore Mountains as an additional processing step to reduce the cassiterite losses into gravity separation tailings (Bulatovic, 2010; Gruner and Bilsing, 1992). Although the reported lower size limits for an effective cassiterite floatability are often smaller compared to other minerals, the flotation performance is in general decreasing for small particle sizes < 10 µm (Trahar and Warren, 1976). Therefore, different approaches have been already investigated for the flotation of such fine cassiterite fractions to overcome the limits in particle size. Bilgen et al. investigated the shear flocculation of cassiterite with a sulfosuccinamate collector (Bilgen et al., 1994). The agglomeration flotation of cassiterite has been tested by Schubert et al. (Schubert et al., 1966), in which the selective coagulation of fine hydrophobic particles and oil droplets leads to an increase of the effective particle size. Recently, Leistner at al. investigated an oil-assisted agglomeration flotation for ultra-fine cassiterite ore fractions (Leistner et al., 2016). However, a poor response due to an increased concentration of Fe and Ca ions, unselective oil/gangue coagulation and froth instability, that is caused by oil/frother interactions, has been observed."

Jan 1, 2018

By Shuji Owada, Mayumi Ito, Idemitsu Kosan Co. Ltd., Takehiko Nishimu, Sadayuki Shinozaki, Takashi Ando, Tomoe Ota

"fElectrical disintegration (ED) by high voltage electrical pulse is a relatively new technique which was demonstrated by Tomsk and Mekhanobr in the 1960’s and has been investigated in detail by Andres in the 1990’s. In the ED, the electrodes should contact to the targeted material and the energy of high voltage pulse is charged directly to the material. It has been reported that the ED is quite efficient to improve liberation of composite materials, because electrical current passes often through the conductive part and/or along the phase boundaries. Theoretically, the energy required in the ED should be lower than in the other mechanical breakage methods, because breakage occurs basically by tensile strength in the ED while in the other mechanical methods it does mainly by compressive strength which is generally ten times or higher than tensile strength.Coal, involving many kinds of mineral matters, is considered to be one of the targets for the ED to apply to. In Japan, national “Hyper-Coal Project” is now running, in which ultra-clean coal (less than 200ppm of ash, 0.5ppm of Na and K, and 2ppm of Ca) is planned to produce by combining advanced coal preparation and liquefaction technologies for the purpose of direct injection of coal combustion gas to turbine. The ED is one of the major techniques to be developed in this project, since mineral matters must be liberated before introducing to the following advanced separation processes. Liberation is important also for the utilization of middling coals generated from usual coal preparation plants. The application of the ED to the middling coals is considered effective for upgrading these coals with higher liberation degree and less energy input."

Jan 1, 2003

By Ayumu Tokumaru, Shuji Owada, Gangfeng Liu

"Several million spent catalytic converters are disposed annually worldwideandeach containing about 0.5-1g ofplatinum and 1-2g of all the platinum group metals (PGMs), then,it is fairly significant to recover PGMs from the spent automobile catalyst. The PGMs’ recovery is a proven technology, including pyro-and hydrometallurgicalmethods, and the highestrecovery can achieve approx. 98 wt.% by acid-leaching method, but theserecyclingtechnology seems to be too highlyenergy-consuming. SincePGMs aredistributed only in coat layer in spent catalyst, it is of great significance to enrich the coat layerwith some physical methods as a pretreatment.In this paper, according to the double-deck structureof the catalyst andthe different properties of the two main compositions, alumina-ceria phase of coat layer and cordieritephase of substrate, the concentration of the coat layer was investigated by combiningthree kinds of physical separation technologies, heating-quenching, crushing and surface grinding. In the first stage, thermal stresscouldgeneratebetween the two phasesby thermal expansion difference,to producefracturesin the thinnest part of coat layerand micro-cracksin coat layerand at the interface of coat layerand cordierite substrate. The second stage of crushing, by jaw and roll crushers, could break dominantly the coat layer and the third stage of surface grinding, carried out by attritor, promoted further separation and concentration of coat layer fromthe substrate.We also improved the attritor grinding by adding a new lift-arm to the cell for achieving better mobility of sample particles in the selective surface grinding."

Jan 1, 2014

By Felipe Sepulveda, Edelmira Gálvez, Luis Cisternas

"In mineral processing, the recovery and/or concentration of the value components cannot occur in one operational stage, therefore requiring the use of separation circuits based on several flotation stages. The components to be separated are typically distributed at different concentrations and different particle sizes, resulting in different levels of recovery. Typically, more than one value component must be selectively removed by exploiting the differences in the components’ floatability at different pH values, pulp potential and particle size. Several methods for the design of these circuits are available in the literature, but comparatively few studies present circuit analysis tools or address the design of a multiple-product flotation circuit. In this study, global sensitivity analysis was used to analyze a flotation circuit with several products, such as copper, lead and zinc. This analysis was based on the Eureka mine concentrator plant. The analysis was performed for each of the sections of the circuit as an overall evaluation of the circuit. The Sobol’ method and the correlation method were used to evaluate the Eureka mine concentrator plant using the SimLab 2.2 software."

Jan 1, 2014

By Wei Zhang, Jinhong Zhang

"In froth flotation, the adsorption of collector on mineral surface is critical for a successful flotation process. In present work, an atomic force microscopy (AFM) has been applied to study the adsorption of potassium amyl xanthate (PAX) on copper sulfides, i.e., chalcopyrite, chalcocite and bornite. The in-situ collected AFM images show that PAX adsorbs on chalcopyrite mainly in the form of oily dixanthogen; while it strongly adsorbs on chalcocite and bornite in the form of insoluble metal xanthate, which binds strongly with the mineral surface. The information obtained from the AFM study shed lights on the collectivity and therefore the selection of specific collector for different copper sulfide minerals in industrial practice.INTRODUCTIONFroth flotation, which treats the highest throughput in mining industry and produces the maximum economic outcome of any surface chemistry process, has been widely applied for the concentration of copper sulfide minerals, i.e., chalcopyrite, chalcocite and bornite. In flotation, collectors are added into the pulp (mixture of water and fine-grained minerals) to selectively adsorb onto the target mineral and render its surface with high hydrophobicity, which is generally beneficial for a strong mineral-bubble attachment and thus a high flotation recovery. Therefore, the adsorption of collector on mineral surface is vital for a successful flotation process and it has been studied by applying various surface analysis techniques, such as IR (Infrared Spectroscopy), CV (Cyclic Voltammetry) and XPS (X-ray Photoelectron Spectroscopy). (Poling, 1963; Allison et al., 1972; Mielczarski et al., 1984; Leppinen et al., 1989; Kartio et al., 1996) These studies have revealed a lot of information, such as the reaction, product and mechanism, of the adsorption of chemicals on mineral surface. It is also of great interest to directly get the image of adsorbed collectors on mineral surface changing with pulp chemistry, such as pH, redox potential, ionic strength and chemical’s dosage."

Jan 1, 2018

By S. Gaydardzhiev

Initial experiments towards preparation of hollow ceramic microtubes by dip-coating of fibrous plants with water based alumina gel-casting slurries using hemp and coconut fibres as templates have been done. It has been found that the wettability of fibres and accordingly the stability of the developed ceramic layer on their surface during slurry gelation varied significantly within the different fibre types. Good correlation between the diameters of the template fibres and the resulting channels has been found at the level of solids loadings used, 31 %. Hemp fibres used as bundles have led to formation of multi channel patterns while the coconut fibres-templated process resulted in uniform monochannel materials. The micro tubes have show good mechanical handling.

Jan 1, 2014

By Matthew Thurley

Optimisation and control of comminution, pelletization, and agglomeration processes is a complex task with large potential for gains in productivity, energy efficiency, and particle size distribution quality. One factor in realising these gains is the requirement for fully-automated online particle size distribution measurement. Moreover, online particle size distribution measurement that is based on the particles on the visible surface and can avoid or mitigate substantial errors that result from under-sizing overlapped particles and over-sizing areas of fines particles. Literature review indicates a body of substantially 2D photographic based particle size measurement systems that suffer from a large number of significant errors except in the simplest case of a monolayer of particles under good illumination with limited color variation in the material. In order to measure the visible particles on a pile there are a number of requirements including; avoiding particle delineation errors due to variation in material color and shadows, detect overlapping versus non-overlapping particles, and identify areas of fine particles as fines and not large rocks. Results are presented using a fully-automated online measurement system of crushed rock on conveyor belt using a 3D surface laser profile. The system provides continuous online measurement and results are shown on over four hours of production after the primary crusher. Size distribution results are calculated using volumetric estimation of the particles on the surface of the pile. The results show a strong capability to discriminate size variation especially in the 10% and 20% passing values. Furthermore results show that if areas of fines are misclassified as large rocks, and overlapped particles misclassified as small rocks, then a near complete loss of discrimination occurs for the P10 and P20 values which become largely constant values.

Jan 1, 2014

By D. Berman, A. Brodt

"Delivery of all volume of mined mass on the terrestrial surface results not only in irrational power expenses on moving of huge volumes of dead rock as a part of initial raw materials (especially vertically) on long distances, but also necessities of storing tailings in open-air. Thus, in bowels of earth, huge volumes of the developed space are formed. However, the nature doesn&apos;t suffer emptiness. As consequence, through the process of underground mining works, in earth bowels starts intensive development of rocks dislocation processes involving subsidence of terrestrial surface, and with it, begins irreparable damage every objects which are on that territory. Highly effective new methods of underground concentration of the various minerals, which deliveries of only target component on terrestrial surface integrally connected with transport process in stream and subsequent deliveries to destination in continuous mode by the long distance hydrotransport, allow not only to eliminate a construction of concentrating factories on the surface, but also storing of tailings of concentration process on open-air preventing dislocation of rocks, thanks to operative placing tails in the underground developed space. Surely, the main problem in the development of such gravity dressing technology is the problem of finding the optimal formula for the heavy liquid that will fill such system in close connection with the procedure of its full regeneration. The requirements for such liquid are being non-toxic and cheap. This question was solved successfully."

Jan 1, 2014

By Çisem Tuba, Ismail Girgin

"Comparative atmospheric H2SO4 and H2SO4 + H2O2 leaching experiments were performed using a Turkish lateritic nickel ore containing 1.52% Ni. In the leaching tests; acid concentration, temperature and leaching time were considered as main variables and the dissolution behaviour of the ore were studied by Ni, Fe, Co and Mg analyses. The dissolution values in the H2SO4 leaching experiments were observed to increase up to 60% (w/w) acid concentration and a temperature of 95°C. Increase of H2SO4 concentration above 60% at 95°C caused decreases in all the dissolution values and this was attributed to the formation of Fe2(SO4)3 and Fe2(SO4)3•HSO4•H2O type compounds. At the considered optimum H2SO4 leaching conditions ([H2SO4]= 45%, T=95°C, t=45 min); dissolution values reached for Mg, Ni, Fe and Co were determined as 99.12%, 95.58%, 92.63% and 78.37%, respectively. An activation energy of 30.57 kJ/mole was determined for nickel dissolution from the evaluation of the kinetic data obtained for H2SO4 leaching showing that the dissolution was controlled by external diffusion and chemical reactions. Caro’s acid solutions were prepared at H2SO4/H2O2 mole ratio of 3 for varying initial H2SO4 concentrations and leaching tests were performed at 25°C. Co behaved very differently and a dissolution value of 83.94% was obtained even at 5% acid concentration in 60 minutes reaction time. Complete dissolution of Co was obtained after 30 minutes of reaction time at 60% initial H2SO4 concentration and the corresponding dissolution values for Mg, Ni, and Fe were reached to 96.16%, 94.27% and 89.46%, respectively. Although the H2SO4 + H2O2 leaching experiments were conducted at 25°C, it was realized that the temperature of the leaching medium was increased to 122°C after four minutes of reaction time due to probable exothermic reaction(s) at 60% initial acid concentration."

Jan 1, 2014