Search Documents

By K. Haga

In this study, flotation tests were performed to investigate behavior of enargite and chalcopyrite ores from different sources synthetically mixed for separation of enargite. Flotation parameters including; pH, reagents concentration and type and flotation time were controlled to obtain an enargite concentrate with high As and chalcopyrite concentrate and final tailings with As content below 0.5 mass%. The copper ore bearing enargite mineral contained 5.87 mass% As and 16.50 mass% Cu while the chalcopyrite bearing ore contained 0.32 mass% As and 21.63 mass% Cu. The two ore samples were mixed at 7:3 (enargite: chalcopyrite) by weight ratio to prepare a mixed ore sample with arsenic content at 3.16 mass% and 18.25 mass% Cu for the flotation study. For enargite single ore flotation, the 38?75 µm size fraction showed that over 98% enargite was selectively recovered within 5 min at slurry pH of 4.0 and arsenic content in the final tailings was reduced to 0.22 mass%. In mix ore (enargite+chalcopyrite) flotation, 97% of enargite was first removed at pH 4 followed by chalcopyrite flotation at pH 8, and over 95% recovery was achieved in 15 min flotation time. Arsenic content in the final tailings was reduced to 0.1 mass%.

Sep 1, 2012

By N. Syna

The selection and preparation of activated carbon suitable for specific application can often involve exhaustive adsorbent preparation and testing. This work examined an emerging technique based on modelling the correlation of observed adsorption capacity to the carbon characteristics as a means of decoupling the roles of carbon textural and surface chemical properties. The insights to these specific roles are then used in tailor-making adsorbents and in establishing the optimal carbon properties for specific application. In this study, a series of activated carbons prepared from bagasse by physical and chemical techniques and commercially available carbons were used in developing the models. These carbons were tested for the adsorption of thiourea-gold (I) chloride complexes. Thiourea is an important alternative gold lixiviant with the potential to address current ecological and safety concerns in the extraction of gold. A four-component model, which correlated the adsorption gold capacity to carbon textural and surface chemical properties, was proposed. The model fit was assessed using multi-linear regression and a partial F-test. This was followed by goodness of fit test achieved through r2, adjusted?r2 and mean square error (MSE) values. The results suggest the adsorption of the gold-thiourea complex is strongly influenced by the internal surface area and pH of the carbon. Tailor-made activated carbon from bagasse showed adsorption gold capacities of up to 198 mgAu/g adsorbent, demonstrating the potential of bagasse as a precursor for gold adsorbents and of this empirical modelling approach in developing adsorbents for metal recovery.

Jan 1, 2014

By A. V. Nguye, P. A. Harvey

Previous studies have reported that inorganic electrolytes can enhance floatability of coal. The research has shown that the enhancement, if any, is highly dependent on changes in solution pH, type of electrolyte, and electrolyte concentration. The reasons for this are still not clear. In this study the floatability of coal particles in mono and divalent salt solutions was investigated. The zeta potential and hydrophobicity of the coal was measured experimentally, and a modified Hallimond tube was used to determine the floatability of coal particles by single bubbles, where the collision efficiency was equal to unity. The experimental information was used in conjunction with the Hogg-Healy-Fuerstenau equation to quantify the electrical double layer interaction. It was found that for low electrolyte concentration (less than 0.1 M) solutions the flotation recovery of coal particles was less than that for distilled water, and decreased with increase in concentration. Conversely, at electrolyte concentrations above 0.1 M, flotation recovery increased with increasing concentration. Both of these results are consistent with previous observations, but are inconsistent with expectations when considering the possible influence of electrical double layer interaction. A possible mechanism, based on the existence of the pre-existing submicron-sized gas bubbles, known as bubstons (i.e. bubbles stabilized by ions), present in water in close proximity to the hydrophobic coal surfaces is discussed in line with the early observation of flotation improvements by microbubbles “nucleating” on hydrophobic surfaces. In particular, the dependence of the bubble-particle attachment efficiency on electrolyte concentrations supports hypothesis on the salt-dependent and ion-specific existence of bubstons. However, a theoretical explanation of the transition salt concentration (at about 0.1M) is deficient at present. The existence of these submicrobubbles in close proximity to hydrophobic surfaces is not trivial. They can (as can individual gas molecules or other solutes) mediate and extend the range and magnitude of the attraction between hydrophobic macroscopic surfaces. These bubbstons may explain the curious phenomena of the socalled long-ranged hydrophobic attraction measured with the Surface Force Apparatus and Atomic Force Microscopy, and the slippage at hydrophobic surfaces. Finally, the coalescence of bubbstons affects the rupture of liquid films at a very large thickness (over 100 nm), observed, but unexpected, by flotation chemists.

Jan 1, 2003

By Steven Wright, Sharif Jahanshahi, Shouyi Sun

"While there is a large industry based on recovering platinum group metals (PGM) from complex sulphide ores containing Cu and Ni, there is little information on the thermodynamics of the matte phase formed on smelting the ore and in particular the behaviour of Pt in the matte.The equilibrium between metallic platinum and industrial mattes was studied in a series of experiments where a small quantity of matte (5g) and platinum foil of 150 µm thickness (0.5 g) were equilibrated in magnesia crucibles at 1400°C under conditions where the oxygen and sulphur partial pressures were fixed.The chemical composition of the phases was determined from EDS analysis using a scanning electron microscope. Line scans were initially used to confirm that the foils had attained a uniform composition across their thickness. The composition of the matte was determined from analysis of an area of matte including the small metallic droplets and dendrites.The results of the equilibrium study are presented in terms of how the oxygen and the sulphur pressure affect the distribution of Pt, between the matte and the alloy foil (Lmatte/alloy). Other variables investigated were matte chemistry, i.e., the Fe content and the temperature. The activities of platinum in the mattes were calculated using a regular solution model describing the activity-composition relationship in the alloy."

Jan 1, 2003

By S. Kondratiev

Mechanism of the action of nonpolar physically adsorbed reactants in froth flotation is under discussion in the paper. It is shown that their basic influence on flotation includes removing of the kinetics restrictions of the flotation complex formation. Experimental data and practical evidence reported in the paper sustain the proposed mechanism. There are discussed potential dependence of the kinetics of dixanthogen formation on platinum and its influence on the induction time (IT).

Sep 1, 2012

By R. ?. Shishmarjov, Yu. ?. Davidenko, S. V. Bukhalov, ?. S. Baksheev, M. S. Shkirya, N. ?. Aikasheva, D. V. Bogdanovich, ?. Yu. Faustova

"The goal of prospecting operations in the Republic of Altay was to locate gold-sulfide-quartz mineralization. For this purpose we applied the technology of electromagnetic sounding and induced polarization (EMS-IP). These operations resulted in localizing promising sites with presence of sulfidization. The EMS-IP method proved to be highly efficient amongst other prospecting methods targeted at recognizing zones of sulfide mineralization making up 91%, considering that in more than half cases the ore intervals were the case. In the Yakutian diamondiferous province the EMS-IP technology was approbated during three field seasons to accomplish the assignments on searching for kimberlite bodies under conditions of various geological types. As a result, the reference objects were distinguished, and geoelectric parameters of kimberlite pipes of explosion were defined.INTRODUCTION In the time span 2015-2016 in Gorny Altay the EMS-IP technology was approbated in the Novokuznetsk area. The on-land areal geophysical survey was performed by EMS-IP method applied to identify, outline and locate promising sites with Au-Ag-bearing polymetallic mineralization within surveyed areas. Compared to the hosting rocks, the sulfides contained in polymetallic mineralization are typified by low specific electrical resistivity (SER) and high polarization. The areal survey conducted via EMS-IP method provided spatial characteristics of searched object. From July 2016 to August 2017 our expedition group carried out serial test works and laboratory investigations intending to define performance capabilities of EMS-IP technology in searching for kimberlite bodies under conditions of diverse geological types. The prerequisites for serial work were operations accomplished at the «Listvenichny» site lying 35 km away from Mirny town in the Sakha Republic (Yakutia), where the EMS-IP technology was probed for locating position and measuring geoelectric parameters of tuff pipe «Buardakhsky». After successful completion of operations it was decided to evaluate geoelectric parameters of kimberlite pipes of explosion."

Jan 1, 2018

By M. Holuszko, I. Mikhalev

"Previous studies described by Galvin et al. (2017) have shown that for Australian bituminous coal fines, both in batch and in continuous process, the new improved oil agglomeration procedure based on the use of high-internal-phase (HIP) emulsions, as compared to the conventional “pure oil” agglomeration process, enables a significant reduction in the amount of oil while reaching a high yield of clean coal (approximately 90% of agglomerates greater than 355 µm in size) in a significantly shorter time. The HIP emulsion used in these experiments comprised up to 95% vol. aqueous solution of sodium chloride (3% wt. concentration) and for the rest, a mixture of kerosene (oil) and sorbitan monooleate (SMO emulsifier) in a 1:1 ratio as a binder. This study evaluates the applicability of the new HIP-oil agglomeration process to treat Canadian bituminous ultra-fine coal and Russian sub-bituminous coal fines and compares results from agglomeration to the flotation response of both coals. Oil agglomeration is known to be sensitive to surface properties of coal. Since surface properties of coals depend not only on the rank of coal but also on their origin (depositional environment) and mineralogical composition, both the applicability of this new improved agglomeration process to the non-Australian coals and its efficiency became the motivation for this study. To evaluate the applicability of the new process to both Canadian bituminous and Russian sub-bituminous coals, a series of bench-scale tests were carried out under conditions similar to those described by van Netten et al. (2016) for the Australian coals. Based on the results obtained in this research, new boundary conditions for the application of the HIP emulsion-based oil agglomeration process have been outlined and conclusions on the viability of the new process to treat ultra-fine coal from Western Canada and Russian sub-bituminous coal fines have been reached.INTRODUCTION In most cases, to meet the market requirements, the mined coal has to be processed to reduce the ash content by the removal of mineral matter and thus to increase the quality of the coal products (van Netten et al., 2016). Generally, flotation is used for processing fines from high rank coals; however, there are high losses of very fine coal due to the inefficiency of this process. Furthermore, difficulty in dewatering the fine coal results in excessive moisture levels causing coal handleability issues, which increases costs in the coal-cleaning industry (Capes & Darcovich, 1984). Much of the development that has occurred in fine coal cleaning has taken place with higher-value coal, often metallurgical (Klima et al., 2012). If the fine coal is deemed to be too difficult or expensive to process, it may be discarded as waste (van Netten et al, 2014). Such disposal not only creates an environmental liability but may also result in the loss of a valuable, high quality product that is better liberated than the coarser fractions of coal."

Jan 1, 2018

By Y. H. Tang

For its surface features, micro-sized hematite is usually difficult to recover by magnetic separation; especially, the existing high gradient magnetic separator in industry can not utilize collecting matrix with thin silky rods for its property of being easily blocked; the lower size limit for recovery of micro-sized weak magnetic minerals is about 0.019mm, some even is 0.037mm. This paper introduces the application of the combined new technique of water-air joint discharging of concentrate and collecting matrix with different diameter silky rods in the field of recovery of micro-sized hematite by high gradient magnetic separator. The commercial test result for recovery of a certain hematite with size about ?0.037mm shows that the recovery can be promoted by 16.81% with basically same concentrate grade.

Jan 1, 2014

By Lilong Huang, Xiang Zhao, Yuan Long, Li Shi, Guowang Zhang, Xiao Xiao

"Vertical stirred mill is expected to upgrade the iron concentrate by further size reduced efficiently. The tests for fine grinding of iron ores from Baiyun Boyu iron ore, Baogang Goup, iron contained tails of Cu-Pb-Zn ore in Wanguo ore, Xiaoshalong iron ore in Qinghai were conducted in this paper. The data of appropriate grinding fineness, optimum grinding conditions and energy consumptions obtained from the test were used to select appropriate scale of the vertical stirred mill, optimize the parameters of the grinding process and upgrade the iron concentrate of the iron ore dressing plant or design the new ore dressing plant. Based on the laboratory tests, industrial system of regrinding and magnetic separation with vertical stirred mill as the regrinding mill in micro-fine grained iron concentrate upgrading has worked out very well. The grade of Fe in iron concentrates has increased to about 65.0% (by 4.0~6.5 point percent) when the iron concentrates were reground to designed fineness and the specific energy is 5.0~7.1kWh/t. The system of regrinding and magnetic separation is proven to be eco-efficient in iron concentrate upgrading."

Jan 1, 2014

By Aziza A. Yousef, Suzan S. Ibrahim, Mahmoud A. Arafa, Mohamed A. Abdel Khalek

In view of the shortage of soft water all over the Middle East countries, seawater may be used to replace the fresh water in flotation beneficiation. The flotation process required about 7 m3 of fresh water/ ton ore. This article aimed to study the effect of seawater cations and anions on the flotation process of four important mineral commodities. The adsorption of collector, zeta-potential, zero point of charge and floatability of pure minerals were studied. The individual effects of different cations and anions that are predominant in seawater, within their more or less actual concentrations were studied on individual mineral and on groups of them. The troublesome Ca2+ and Mg2+ ions, in the anionic circuit could be controlled by soda ash addition to the pulp before the anionic collector. The addition of sodium silicate improved the floatation selectivity of mineral mixtures and natural ore. At the optimum conditions the calcareous phosphate ore yielded a concentrate recovery of 83% with a grade of 34% P2O5, with 0.61%MgO, which from an ore assaying (25.3% P2O5 and 9.4% MgO).

Jan 1, 2003

By B. Aydin, G. Erturk, G. Bulut

Coal is a complex material because of its structure consisting of carbon constituents and mineral matter. Flotation is readily carried out due to hydrophobic characteristic of coal. Therefore coal flotation is the most commonly used technique for fine coal beneficiation in order to acquire clean coal separating ash forming mineral matter from carbonaceous matter. In the coal flotation, floatability of coal both depends on characteristic of coal and used flotation reagent. Frothers as a flotation reagent are used to facilitate air dispersion into fine bubbles by prevention of bubble coalescence in the pulp phase, and stabilization of flotation froths. In this study, the effects of frother types and concentrations at different pH and particle size on the coal flotation were investigated. The representative sample was taken from Zonguldak, Turkey. It contains 9.1% ash and 7313 (kcal/kg) calorific value. Pine oil, Dowfroth 250, MIBC and Isooctanol were tested as frother types. It is determined that 1.92 ppm frother concentration is sufficient to float coal, except pine oil. In mixed frother tests, it is seen that Dowfroth 250 is more effective than others. No significant difference in coal recovery was observed for flotation tests at the different pH values. The best results are obtained in size of coal (-0.1 mm) with all frothers.

Jan 1, 2014

By Xiaojing Li, Yueyuan Zhou, Shengyao Ma

The paper presented the acnalysis of field intensity of rare-earth permanent magnet with high BH product and the research of magnet configuration with narrow pole pitch on open magnet surface, both using ANSYS. The possibility to separate micro-disseminated feebly magnetic minerals by improving the field intensity and the capture line distribution rate on open magnet surface were verified. The research on the method to pile up magnets to increase peak value of field intensity on the open magnet to 1.0T was done through correlation analysis between shape and dimensions of magnetic material and field intensity. And the research on technology method to improve capture line distribution rate in the separating field to 1.25×105/m2 was done through optimization design of magnet configuration of the open magnet with narrow pole pitch. Laboratory tests were performed with hematite sample from ore dressing plant such as Hainan mine, Qidong iron ore, etc. The separation results acquired were at the same level as using the electromagnetic separator, verifying the possibility to separate micro-disseminated feebly magnetic minerals with open magnet. The research suggested a new idea about the development of magnetic separator with high efficiency and low costs to separate feebly magnetic minerals and non-magnetic gangues.

Jan 1, 2014

By Dongyun Liang

Process mineralogy focuses on the chemical components and mineral composition of ore, dissemination size of valuable minerals, the occurrence of valuable and detrimental elements as well as the behavior of each mineral in the process. Through determining process mineralogy parameters and analyzing the characteristics of minerals, the results of process mineralogy study can provide mineralogy data for making a reasonable mineral processing technology program and optimizing the process. A detailed process mineralogy study is carried out for a complex rare metal ore in this paper and the results show that niobium mainly exists in the form of ferrocolumbite as well as nioboaeschynite and zirconium primarily occurs as zircon. The valuable minerals including Th-nioboaeschynite, ferrocolumbite, zircon, etc. have the characteristics of fine dissemination size, wide size range, complex chemical composition and variable physical properties, which mean it is a refractory ore. According to the results of mineral composition of ore, chemical composition of minerals, dissemination size of minerals, magnetism ranges of minerals and the distribution of niobium and zirconium, the process of ?desliming-Nb-Zr bulk flotation? is designed for this ore and the niobium-zirconium bulk rough concentrate with the grade of Nb2O5 9.43%, ZrO2 24.95%, Ta2O5 0.36% and the recovery of Nb2O5 77.66%, ZrO2 76.70%, Ta2O5 75.13% to crude ore can be obtained in the whole process closed-circuit test.

Sep 1, 2012

By Junji Shibata

In a present process to treat the tungsten carbide tool waste, the wastes are roasted in air and then an alkali leaching is carried out in an autoclave. An environmentally friendly process is required to recover rare metals (Co and W) from the wastes. The effect of mechano-chemical (MC) treatment on leaching of rare metals was investigated in this study. The solvent extraction and crystallization-stripping methods were applied to separate and recover tungsten and cobalt in the leached solutions. The MC treatment for the rare metal leaching is effective to dissolve rare metals from the wastes due to the change in crystalline structure of WC and oxidation of WC with KMnO4. Cobalt ions are extracted with D2EHPA by a cation exchange reaction. Tungsten in the leachate can be extracted by TOA (tri-octyl amine) as an extractant, because tungsten species exist as a form of anionic species in acidic solution. The rare metals in organic phase are recovered as insoluble salts such as oxalates and ammonium salts in the crystallization-stripping process. Keywords:unheated oxidation, solvent extraction, crystallization-stripping, recycling

Sep 1, 2012

By S. M. Viduka

This paper presents a numerical investigation of solid separation in jigging device, which is a gravity separation method widely used in ore processing. Separation is recognized as being heavily dependent on fluid motion in the jig. This study explores the effects of the inlet time dependent velocity profile on jigging performance. Modelling of the liquid-solid system is performed through a combination of computational fluid dynamics (CFD) to simulate liquid flow and discrete element method (DEM) to resolve particle motion. The initial packing conditions consist of a binary-density particle system of 1130 particles each 1 cm in diameter. A variety of jigging profiles are implemented in jigging. The saw tooth pulsation profile is selected with three variations in both amplitude and frequency. The performance of each profile variant is compared in terms of solid flow patterns, separation kinetics, energy, and mean particle position. These quantitative comparisons demonstrate significant differences in the segregation rate, energy, and solid phenomena, helping find an alternative optimum operating setting for the system.

Sep 1, 2012

By I. Grigoryeva, G. Voiloshnikov, V. Dementyev, N. Moskaeva, N. Voiloshnikova

"Adsorption processes with use of anion exchange resins are widely applied in the gold mining industry of Russia and the former Soviet Union. Anion exchange resin AM-2B and its analogs (with mixed basicity) are used as adsorbents. This paper focuses on the study of weak base anion exchange resin and its comparison with AM-2B resin. Different nature of the ion exchange groups of the adsorbents mentioned above provides essential differences in their properties both during adsorption and elution of gold and silver. Multistage gold elution and resin regeneration procedure is used for AM-2B resin whereas alkaline cyanide solution is used for weak base resin and allows for the reduction Capex and Opex in comparison with AM-2B resin. Anion exchange resins AM-2B and PuroGold S-992 were tested. Weak base resin is sensitive to pH of adsorption medium. Optimal pH value is 10.1-10.3 (at ?? >10.5 gold loading onto resin decreases dramatically). Adsorption isotherms for gold, silver, nonferrous metals, cyanide and thiocyanate ions from synthetic individual metal cyanide solutions were defined. Adsorption of all components onto PuroGold resin was lower than for ??-2? resin. Adsorption of metals from the solution with equal molar metal concentration (0.1 mg-equivalent/L of each metal) was also studied. The affinity of resins to cyanide metals complexes was established. Weak base resin has higher selectivity to gold in comparison with ??-2B resin and is less sensitive to ion composition of cyanide solution or pulp treated. Weak base resin was tested for gold recovery from gold ores. On the base of test results it was recommended to introduce this resin at some new plants in Russia. Commissioning and operation performance of gold plants confirmed efficiency of weak base resin use."

Jan 1, 2014

By John Starkey

"The development of the Minnovex SAG Power Index (SPI) Test in Canada has created a new and accurate way to measure ore hardness in a SAG environment. Coupled with the standard Bond Ball Mill Work Index Test it is now possible to determine from these two relatively inexpensive laboratory tests, the amount of energy required to grind an ore from the primary crushed size to the desired liberation size. By testing multiple samples to discover where the hard and soft ore zones are located, the representative hardness distribution for the ore body can be determined and grinding equipment selected that is capable to meet production targets for all mining areas of the deposit.In the last century, it was deemed prudent to select up to 50-tonne samples of ore for Semi Autogenous Grinding (SAG) pilot plant tests and a second 5-tonne sample for metallurgical pilot plant work. The methods outlined in this paper show how the 50-tonne sample is no longer required for SAG design because it is better to measure the representative hardness distribution of the ore body than the hardness of a “chosen” representative sample. This is demonstrated to be true by the fact that the lower horizons of an ore zone cannot initially be accessed to recover 150mm pieces, and the bulk samples taken, rarely represent the desired design hardness of the ore. Median hardness will not yield a good result in most cases and a clear understanding of the location and extent of the hardest zones is imperative to achieve a truly successful grinding circuit design.This paper discusses two plants (Kubaka and Agnico Eagle) that have been designed using SPI and Bond with no pilot plant test backup. Both have been very successful in that they can grind design tonnage on the hardest ores in the mine. This guarantees that the mine’s profitability is protected in any mining sequence. It also allows the extra power to be converted to higher throughput on softer ores if additional cash flow is needed. The advantages from the owner’s point of view are dramatic. This procedure will be attractive as well when considering the costs for test work, and the samples for testing. Existing diamond drill core is normally used and this allows the inclusion of data from the deepest regions of the mine. In addition, it is also clear that the decision to use a crusher can now be made at the design stage of a project based on measured parameters and the estimated capital costs of alternative designs."

Jan 1, 2003

By S. Owada

A national project of ?Establishing ?Green-Hydrogen (G-H)? Society in Honjo-Waseda Area? is now being developed by Waseda University together with four other universities and ten companies. The project involves three tasks of technological development of, (1)?G-H? production, (2)?G-H? refining, transportation and storage, and (3)?G-H? utilization. This paper focuses the first task of ?G-H? production from aluminium dross. We developed the physical treatment process by combining selective grinding with vibrating rod mill and electrostatic separation, in order to produce two kinds of materials, one is metal aluminium concentrate to recover it and the other is raw material to produce ?G-H? and aluminium hydroxide which can be generated by the treatment with sodium hydroxide aqueous solution. Here, we described the concentration mechanism of metal aluminium in the selective grinding and electrostatic separation and proposed a separation flowchart for optimizing the ?G-H? system in Honjo-Waseda area.

Jan 1, 2014

By Arkady Senchenko

At present, there are different traditional and modern methods for ore grindability evaluation. The correct and rational approach to sampling, testing methods and mill sizing enables one to design a workable technology. This paper contains TOMS institute experience in different grinding indices determination over the last 7 years (SAG Design Test, BWi, CWi, RWi, and other). Mill sizing examples and circuits modeling for the projects in Russia and Kazakhstan are considered. Keywords: ore grindability, SAG Design Test

Sep 1, 2012

By Francesco Vegliò, Luigi Toro, Francesca Pagnanelli

Different hydro-metallurgical processes have been studied in order to recover manganese(II) from oxidised minerals such as MnO2. An innovative acid reductive leaching carried out in mild experimental conditions was here considered using agricultural and industrial wastes containing carbohydrates as reducing agents. The leaching process was investigated from a kinetic and equilibrium point of view in order to optimise the experimental conditions, develop a kinetic model and obtain high purity concentrated MnSO4 solutions. To study the leaching kinetic a Shrinking Core Model (SCM) was modified by a variable activation energy term to take into account both the variable reagent concentrations and the reaction rate change with respect to the manganese dioxide conversion. The influence of the particle size in the kinetic model is discussed with the support of SEM analysis before and after leaching. Manganese extraction yield was maximised (170-190 g/L) using appropriate carbohydrates and acid excesses, while impurity concentrations were kept low (Fe<10ppm and Ca<300ppm) pre-treating the ores, using hydro-alcoholic leaching medium and different combinations of down-stream processes. In particular precipitation, solvent extraction and adsorption onto active carbon were tested to eliminate Fe and Ca from MnSO4 solutions.

Jan 1, 2003