Search Documents

By Stephen Gay, Dewetia Latti

"When improving a plant a mineral processing engineer would like to know the mineral composition distribution. In order to assess this distribution in particles, as compared to the corresponding distribution in particle sections, a procedure needs to be applied to the observed particle sections. Such a procedure is called a stereological correction. There exists many stereological correction procedures, but one group of such procedures is based on using those stereological equations that do not require making assumptions regarding particle shape or texture. These equations are called geometric probability equations.Davy derived a geometric probability equation to estimate the covariance of mineral composition distributions for particles from both particle sections and linear intercepts. This covariance can be used to measure the variance of the particle composition distribution of each mineral. The equation as presented by Davy requires textural information; however the equation was modified by Gay to be more directly applied to particle sections and linear intercepts. The variance obtained from applying this equation is fundamental to the binary stereological correction procedures developed by Gay and his colleagues; the covariance is fundamental to the multiphase stereological correction.Thus far, validation of both the binary and multiphase stereological correction has been achieved using numerical simulation. This paper shall present results comparing the covariance (and variance) estimates from Gay’s equation with actual three-dimensional information obtained from serially sectioning particles. This involved mounting a set of particles and continuously sectioning all particles uniformly so that the three dimensional structure of the particles could be obtained.The mineralogical data to which the equations described above were applied were derived from two individual size fractions from a hard-rock titanium deposit. The deposit contains a range of minerals and of mineral textures and the two size fractions selected were:"

Jan 1, 2003

By M. Brozek, W. Pawlos

"The separation of raw materials in the separator with ferromagnetic liquid occurs due to differences in magnetic and gravitational properties of respective components in relation to each other and to the liquid. In the separator with wedge-shaped pole shoes and the working space axis inclined at a certain angle to the horizontal direction, the paths of grain movement at fixed separation conditions depend on its physical properties. Due to this, the levels of grains outlet from the separator working space are differentiated according to differences in their physical properties. The distance between the levels of outlets from the separator working chamber depends on magnetization of the liquid which is proportional to the liquid density, on the magnetic field intensity and the inclination angle of the separator working passage to the horizontal axis. The separation accuracy is higher the larger is the distance between the outlet levels.The paper will present the methods of visual observation and recording of movement paths of coal grains of different physical properties in the paramagnetic liquid which was the water solution of manganese chloride. The paths were recorded with a video camera in the working chamber by means of a specially constructed device, acting as a periscope, which were then transformed into digital images. Experimental movement paths were confronted to the paths obtained in a theoretical way by means of solving differential equations of movement by a numerical method, achieving good compatibility of experimental and theoretical results. The equations of movement were solved with taking into consideration the drag force, expressed by formula for laminar and dynamic conditions of motion.The course of the path of grain movement depends on grain and liquid physical properties, magnetic field intensity and inclination angle of the working space to the horizontal direction. The two latter parameters can continuously control the process of separation."

Jan 1, 2003

By M. Salas, L. Rolf, H. Z. Kuyumcu

"Industrial use of abrasive stress takes place in the area of fine grinding and in order to clean surface contaminated soil particles. Also, at many mechanical operations abrasion emerge as an unintended side effect. At the Institute for Raw and Waste Material Processing at the Technical University of Berlin systematic investigations are carried out, to further the knowledge regarding the dependence of abrasion process on material properties and stress mechanisms as a basis for design and optimisation of the process or for its avoidance. Aim was the mathematical description of the abrasion process running with a single particle stress. For the purpose of investigations an agitation cell was used. Limestone served as material.In the presented work the influence of particle diameter, particle shape and collision energy on the mass and particle size distribution of abrasion debris was studied. The surface geometry of the particle was characterised by the particle shape factor ?x and the particle diameter dp. The particle shape factor ?x stays in direct relation with the abrasion degree x, and can be substituted by a mathematical function of x.Physically the particle shape factor ?x can be interpreted as a proportion of abrasive stresses splitting up complete crystals and crystal fragments. These two different mechanisms depend on different ratios of curvature of the surface of the stressed particle. The abrasive stress of strongly curved surface areas leads to separation of complete crystals. The abrasive stress of weakly curved surface areas leads to separation of crystals fragments. Accordingly the mass of wear mAb and median diameter of the abrasion debris d50 are different. The derived mathematical relations consider this behaviour by the particle shape factor ?x , which represents the ratio of the mixture of both stress mechanisms. The dependence of the particle shape factor ?x on the abrasion degree x with an exponent approximately to 2/3 points out that the particle shape factor ?x represents a surface area relation."

Jan 1, 2003

By K. Yoo

Cuprous oxide is one of the oldest antifouling agents and also acts as red pigment in these paints. In printed circuit board manufacturing industries, waste etchant contains a substantial amount of copper ion. In the present study, a process was suggested for recovering cuprous oxides from the waste etchant and optimum conditions were investigated to recover the cuprous oxides. The process consists of two steps: in first step, Cu powder is added into wastewater solution, and cupric ions re-duce into cuprous ions (Cu+Cu2+?2Cu+), where cuprous ions precipitate as cuprous chloride; In second step, cuprous oxide is synthesized by adding NaOH into cuprous chloride solution (2CuCl+2NaOH?Cu2O+NaCl+H2O). Optimum conditions were investigated to recover cuprous oxide in the processes. When copper powder was added into wastewater with copper ions, Cu concentration decreased from 15.6% to 2.6% and ORP decreased from 620 mV to -59.9 mV. This result shows that cupric ions reduced into cuprous ions. XRD data indicated that the precipitate was cuprous chloride powder. Using the cuprous chloride recovered and NaOH solution, cuprous oxide was synthesized. To investigate the optimum condition, various NaOH solutions were added into water with CuCl, and then pH, ORP, Cu concentration, Cu contents in precipitates were analysed. XRD data showed that main component of precipitates was cuprous oxide.

Jan 1, 2014

By L. A. Vaisberg

"Crushing and grinding are the two most common industrial processes. These processes consume nearly 20 per cent of the entire electric power produced worldwide. This enormous amount of electric power consumed results from the fact that modern crushing and grinding machines employ the processes first introduced by the prehistoric man, namely those of compression, impact, attrition, and cutting. The material thus handled decomposes indiscriminately, and almost completely ignoring the microscopic cracks and other defects of its structure. Apart from the irrational use of the power, the crushing and grinding processes currently in use result in irretrievable loss of useful components or else in a substantial deterioration of the final products obtained, all as a result of incomplete grinding or, reversely, of overgrinding, palletizing, or fracture of particles.The principal type of equipment that has almost universally been used all over the world for more than 150 years for crushing both natural and synthetic minerals comprises unbalanced jaw and cone crushers. The driving element of crushing bodies in these machines is an unbalanced weight, which transfers the crushing body, allowing it to squeeze the material within the eccentricity value only. The maximum reduction ratio achieved by such a drive is 5, which is due to the rigid kinematic arrangement of the crusher, its dynamic unbalance, and the impossibility of increasing the number of impacts on the material being crushed. Moreover, conventional machines cannot cope with super hard materials, and their mechanism is vulnerable to damage by uncrushable objects.On the basis of fundamental research into the theories of solid body and vibration, OAO Mekhanobr- Tekhnika have developed a range of vibrating jaw and cone inertia crushers that make a reduction ratio of 30 feasible in an open-circuit operation with the reduction ratio monitored within a wide range. In these crushers, the eccentric drive is replaced with a vibrating one. In this way the rigid kinematic drive became dynamic, thus allowing pieces of material to be crushed in a thick layer due to the effect of their bumping into each other, and with the amplitude changing automatically. This results in a number of advantages as compared with conventional crushers:"

Jan 1, 2003

By Zoran M. Stevic, Mirjana M. Rajcic-Vujasinovic, Zvonimir D. Stankovic

"Huge electrochemical investigations have been performed on Technical faculty in Bor (Serbia) which main goal was the clarification of the copper sulfide minerals behaviour in hydrometallurgic and flotation processes. Modeling of these processes was a part of the effort for better understanding of the reaction mechanisms.The consideration of electrical analog circuit and mathematical model of processes at interfaces copper sulfide/electrolyte (CuS/(CuSO4+H2SO4), Cu2S/H2SO4 and CuFeS2/H2SO4), based on studies of the overvoltage – time transients, will be presented. The transients were obtained using single pulse galvanostatic method and electrochemical cell with standard three electrode assembly. In that goal it was developed an original system for computer measurements that enables the application of several methods for electrochemical investigations (galvanostatic, potentiostatic, cyclic voltammetry, electrochemical impedance spectrometry etc). The system was tested and adjusted using commercial electrochemical equipment made by AMEL, Milano.In the first stage of consideration the different equivalent electrical circuits have been tested by computer programme OrCAD 9.2 in order to identify the circuit with responses equivalent in shape to experimentally obtained ones. In that way it was established a configuration of an analog electrical circuit for investigated electrochemical system. That phase enabled only very rough determination of values of circuit components and their relative ratio.In the second stage the method for determination of all elements of electrical analog circuit is described. It is based on mathematical consideration of a given circuit on one hand, and valves of the overvoltages at selected times, obtained from charging and discharging parts of galvanostatic transients, on the other."

Jan 1, 2003

By Tamara F. Kondrateva, Evgenia E. Savari, Galina V. Sedelnikova, Rauf Y. Aslanukov, RAS (INMI), Grigori I. Karavaiko

"The investigation is dedicated to study of biohydrometallurgical processing of refractory gold-arsenic concentrate with the large content of pyrrhotite. Sulfide concentrate of chemical constituents: 75g/t Au, 4,7g/t Ag, 6,3% As, 29,3% S, 2,3% Sb, 0,5% ? (organic) and of mineral composition, %: 11,8 arsenopyrite, 39 pyrrhotite, 12 pyrite, 2,9 antimonite and the rest – aluminosilicates, carbonates and quartz, was studied. The recovery of gold from concentrate by cyanidation is 51,2%. The rest of gold is embedded as finegraded segregation in sulfides.Sulfide oxidation process study is described. Bacterial oxidation was executed on a pilot laboratory unit using combined autotrophic bacterium: A. thiooxidans , A. ferrooxidans, Leptospirillum ferrooxidans and sulfobacillus thermosulfidooxidation, pH=1,5-2,2, t=28-32?C, oxidation time 120 hours. Pyrrhotite is the least stable sulfide mineral with electrode potential 0,45V versus arsenopyrite (0,55 V) and pyrite (0,55-0,6 V) and is oxidated primarily. Pyrrhotite oxidation is followed by large amount of elemental sulphur, which has a bad influence on cyanidation.It’s established that the rate of arsenopyrite (for the first 48 hours) from concentrate containing 39% pyrrhotite is 2-3 times as less as the rate of arsenopyrite bio-oxidation from concentrate without pyrrhotite. The arsenopyrite bio-oxidation is accelerated only after the elemental sulfur was oxidized by bacterium A. thiooxidans and elemental sulfur percentage was reduced from 6,8 to 3,9%. The bacterium concentration is increased from 2,5x107 to 2,5x109 cells/ml. Almost full oxidation of arsenopyrite (98%) and pyrrhotite (98- 99%) is finished in 120 hours. We have studied two pretreatment methods for elimination sulfur content influence on cyanidation: aeration in lime and electrochemical treatment. Such an operation enables to have supplemental oxidation of elemental sulfur and other oxygen and cyanide absorbants before cyanidation. After treatment the content of elemental sulfur was decreased from 3,9 to 2,2%, gold recovery from 90 to 96% and cyanide consumption from 16,2 to 7,2 kg/t decreases. The content of toxical rhodonite-ions in liquid phase of pulp and disinfection reagents consumption were decreased as result of elemental sulfur content in bio-oxidated product reduction."

Jan 1, 2003

By N. Raeis Hosseiny, S. H. Bassir

"Chador-Malu iron ore is one of the most important iron mines of Iran.About 98 percent of Fe in the ore is in shape of Magnetite, Hematite, Martite, aqua oxide of Iron and the other irons are with ferrous silicates, actinolite, cholorite and ferrous dolomites. 1% of Fe has replaced in pyrite. The phosphor distribution in the ore is non-hemogenous and its average in the whole of the deposit is 94%. It is in shape of Apatite.This mine contains considerable phosphor, which makes it useless for metallurgical uses. At this mine the phosphor is reduced in the iron ore at two steps. At the first step, magnetic part of the ore is separated from the gangues and phosphors by magnetic separator. At the second step, the ore is enriched by the flotation methods. Experimental flotation methods to obtain the optimum conditions are as follows:• Effect of Starch as Hematite depressant with ATRAC as Apatite collector• Effect of Sodium silicate as Hematite depressant with ATRAC as Apatite collector• Effect of ASAM as Apatite collector with Sodium silicate as Hematite depressant• Effect of ATRAC (BEROL) as Apatite collector with Sodium silicate as Hematite depressant• Effect of ASAM & ATRAC mixture as Apatite collector with Sodium silicate as Hematite depressant• Effect of Kcarbonate as pH-modifier• Final test to Optimize pH, Collector, DepressantAt this research we have found the optimum circumstance of the flotation of Chador-Malu iron ore in order to decreasing phosphors of iron oxide and floating of Apatite to make pure Hematite.To reach the optimum conditions, some tests were done with different amounts of pH, collector and depressant. The results are as follows:"

Jan 1, 2003

By Leon Lorenzen, Charlene Gokhale

"In excess of 24 x 106 tons (Eskom, 1997) of coal-derived fly ash is produced annually in South Africa for the production of electric power. A large quantity of this ash is disposed of as a solid waste in landfills, thus posing a serious environmental problem. Due to the shortage of landfill sites, new ways of utilising fly ash are needed. Recently several authors have shown that various combustion fly ashes can be converted into zeolites to obtain industrial products with applicability in environmental management. Geopolymerisation has emerged during the last few years as a possible solution to some waste stabilisation and solidification problems. henolic compounds have been shown to be toxic to soil microorganisms at the parts-per-million level. Indeed several of the organic compounds classified by the U.S. Environmental Protection Agency as priority pollutants, are phenols. Immobilisation of phenols by adsorption on zeolites and encapsulation in a geopolymer appears to be a promising solution to this problem.This paper reports a technique for the production of a low-silica sodium zeolitic material from fly ash (zeolite NaP1), and its application for the stabilisation of phenols by adsorption and subsequent encapsulation in a geopolymer matrix. A commercial zeolite, clinoptilolite was also utilised as an adsorbent. Due to their uniform pore sizes and large surface areas, zeolitic materials are suitable for ion exchange and adsorption of certain organic substances. Adsorption data show that the commercial zeolite, clinoptilolite was an effective adsorbent for organics. Adsorption data showed that between 51.2 ppm and 74.3 ppm of chlorophenol or between 15.4 ppm and 32.5 ppm of phenol could be adsorbed. Physical encapsulation of the coated zeolite loaded with organic within a geopolymeric matrix increased the compressive strength of the matrix from 28.80 kN to 40.79 kN. Leaching data for the various geopolymer matrices with encapsulated and loaded zeolites show no organics being leached from the system at a detection level of 2ppm. According to the SABS these would have been acceptable organic concentrations within a waste water stream."

Jan 1, 2003

By Hong Nguen Vu, Pavla Ovcarí, Peter Fecko, Barbara Tora

"The goal of the work was verification of bacterial leaching on the samples of black coal. From the results obtained it was clear that the coal is very well leached by Thiobacillus ferrooxidans and this technology can be used for coal desulphurization. A leaching time of one month is required, to remove 65% of total sulphur and 85% of pyritic sulphur.Microscopic evaluation of samples from Jaworzno showed, that it should be classed as a coal with low coalification, probably from black coal hemiphase. Macerals of the liptinite group were well distinguishable; they were of a dark brown colour. Evidence of coal mass oxidation was apparent on the fresh sample; in the test samples (during bacterial leaching) small grains were oxidised."

Jan 1, 2003

By Jan J. Cilliers, Nicolas Barbian, Esther Ventura-Medina

"Froth structure and stability are known to play an important role in determining flotation recovery and selectivity. An industrial sampling campaign was performed to develop a clearer understanding of the effect of flotation variables on froth stability and the role played by the resulting stability on flotation performance.Froth stability was estimated as the fraction of bubbles bursting on the surface of the froth through image analysis and the solids loading on the bubbles at the top surface. The image processing was performed using the Smartfroth software on the top surface of the froth. The system gives measurements of bubble size distribution, average bubble size and froth velocity. The froth velocity was used to estimate the volume of bubbles overflowing the weir yielding to the fraction of air overflowing the cell. This measurement is the complement of the rate of bubble bursting on the top surface. Also samples of the lamellae were taken by touching the top surface of the bubbles with a glass slide. Then, the amount of solids and liquid per unit area in the bubble lamellae was estimated gravimetrically. Both measurements were used to establish stability criteria.It was generally found that high air flowrates resulted in a drop of froth stability showed by a drop in the fraction of air overflowing and a decrease in the solids loading and simultaneously produced low copper recoveries and low concentrate grades. Deep froths only allowed a small fraction of air to overflow and consequently produced low recoveries. An increase to high frother dosage did not result in an improved fraction of air overflowing, hence producing low recoveries. Likewise, low frother addition only allows low recoveries because the resulting unstable froth cannot support itself. Low aeration was found to be preferential as it allowed high particle loading, therefore high bubble stabilisation, and low gangue entrainment, resulting in the highest flotation performance."

Jan 1, 2003

By Briony C. Ruse, David V. Boger, Fiona Sofra1

"The sustainability of the mining industry must be addressed through improving tailings management. The use of thickened tailings and pastes stems from a paradigm shift towards designing tailings disposal sites to suit their surrounding environment, rather than manipulating the environment to accommodate the tailings. Thickened tailings and pastes usually exhibit non-Newtonian behaviour, so a thorough understanding of the rheological characteristics of the material is required in order to determine the disposal plant operating conditions.As environmental factors translate into economic issues, minimising waste production using dry disposal methods is gaining popularity. The use of rheological information is of high importance in evaluating the spreading characteristics, the transportation and the dewatering of thickened mineral tailings. The principles outlined may be applied to many industries encompassing a wide range of waste materials. The main obstacle to the widespread implementation of dry disposal methods has been the high initial capital cost of the methods due to the dewatering step, and the high cost of pumping thick suspensions across any great distance. Proper and thorough costing of tailings disposal activities combined with an accounting approach that shows closure and post-closure care costs on a per tonne basis of tailings disposed throughout the life of the tailings facility will show that dry disposal methods are more favourable than they might seem on initial appraisal."

Jan 1, 2003

By Rob Morrison, Andrew Scott

"Long before a modern mine commences operations it has already become a wealth of information. After start up, it can generate enormous quantities of data – especially with semi-automated data acquisition by instrumented mine equipment. Much of this data is of limited use for evaluation of (potential) performance unless it links in some way to the site business model.An underlying reason for this waste of data is that the different cultures, financial, technical, community, environmental, etc, not only have many areas of interest but also have very different conceptual models by which they evaluate performance.It is too ambitious to attempt to bring all of these cultures together – in a single step. However, the success of the Mine to Mill ™ project has demonstrated that substantial operational value can be added by using a more integrated approach to comminution. The next logical step is to integrate measured data and then to track performance from ore body model to saleable product and waste disposal.The path from resource to product also represents a path from very sparse, highly variable data to much more detailed measurement and more representative sampling. However, in both cases the data collected is usually strongly focused on the technical requirements – not on the business model.This paper emphasises the difference between data and information. There is considerable potential for confusion between the two as both data and information are often expressed as numbers. For the purpose of this paper, data and information are distinguished by their uses.A data point (or datum) is a measurement. By way of contrast, information provides a basis for decision making."

Jan 1, 2003

By T. V. Chnyrenkova, J. Troncoso, V. A. Luganov, G. P. Kluev

"Arsenic-gold bearing ores are used as flux in smelting or are leached out with extraction of gold. For decreasing arsenic content in processed materials and for breaking up the lattice and opening up of gold the raw materials are roasted. Some regularity was established for sulfidizing of arsenic bearing compounds in a presence of pyrite and for oxidation of ores and concentrates in the presence of soda.This article analyses the results of laboratory and pilot testing of dissociating and oxidizing roasting of gold-arsenic bearing concentrates. During the dissociation roasting under vacuum arsenic is sublimated into elemental and sulfide forms. This process allows minimizing the negative influence on the environment but requires costly engineering solutions. Roasting in a limited quantity of oxygen in the gaseous phase makes it possible to sublimate arsenic in the form of oxides and sulfides and may be carried out in fluid bed furnaces."

Jan 1, 2003

By Vladimir I. Ryaboy, Konstantin M. Asonchik

"At flotation of sulfide-barite ores of one of deposits sulfide and barite concentrates are obtained. In sulfide cycle potassium xantogenate as a collector in consumption of 200 g/ton, methylisobutylcarbinol (MIBC) as a foaming agent in consumption of 30 g/ton and also liquid glass are used. In barite cycle tall oil as fatty acid collector in consumption up to 400 g/ton is used.Sulfide concentrate represents mainly gold- and silver-containing pyrite. The contents of gold makes not less than 10 g per ton, silver - not less than 278 g/t. Barite concentrate contains up to 86% of barite.Factory is working in water recirculation conditions. Owing to that in barite cycle fatty acid collector is used, technological water from tailing repository contains fatty acids soap up to 25 mg/l. Before submission into sulfide cycle this water is conditioned with active carbon to delete the main part of fatty acid collector. The active carbon consumption makes 0,4-0,5 kg per 1m3 of water or 1,5-2 kg per ton of ore. The above mentioned consumption of active carbon improves reducing of contents of fatty acid collector from the initial concentration of 25-30 mg/l to 4 mg/l. At concentration 4 mg/l fatty acid collector does not render negative influence on flotation index in sulfide cycle. At the absence of active carbon pollution of sulfide concentrate and its irrevocable lost are observed."

Jan 1, 2003

By Scott C. Brown, Ivan U. Vakarelski

The particles commonly encountered in mineral benefication schemes have irregularites that are expressed at many different length scales. In part, this originates from preceding processes (e.g. makedown, comminution, handling and storage), which are known to chemically and physically modify the bulk particle and its surface. Interparticle tribology, dissolution and reprecipitation events along with large-scale mechanical stresses are just a handful of the interactions encountered during processing of particles prior to separation. It is feasible to imagine that each one of these events may impose a fingerprint of characteristic nanoscale, microscale, and macroscale morphological changes that can modify the overall interaction of these particles within a system. Suprisingly there are just a few works on how these resulting features can alter the performance of benefication schemes, and especially flotation.

Jan 1, 2003

By H. U. R. Kattentidt, W. L. Dalmijn, T. P. R. de Jong

"Research at Delft University aims to develop systems for automatic inspection and sorting of bulk solids which can be applied in the mineral processing and recycling industry. A recent development includes an automatic sorter based on airport X-ray inspection technology. It is designed for continuous inspection and sorting of 5 – 150 mm solids and has as objective a cost effective and high capacity on-line inspection and sorting.Dual energy X-ray transmission imaging provides instantaneous data about particle dimensions and the atomic number distribution. The system provides particle thickness and average atomic number on a pixel level at scanning speeds between 250 and 500 lines / second. With existing X-ray components inspection speeds between 0.5 and 2 m/s at approximately 1-meter inspection width and between 1.5*1.5 and 5*5 mm2 sensor resolution can be achieved.Imaging algorithms that were developed by Delft University for applications in recycling, waste cleaning and other applications acquire shape, size distribution and composition data. Currently on-line processing of a product at a rate of around 200 particles per second is possible using a standard PC. Experiments with a demonstration X-ray unit indicated good potential for various applications in solids processing. They include continuous inspection of organic content, sulphur, chlorine, ash, and metal distribution. It is applicable for coal cleaning, ore sorting, industrial minerals, and various applications within waste cleaning and recycling. Dual energy X-ray transmission fundamentals and recent progress in system development and applications are presented."

Jan 1, 2003

By Jan J. Cilliers, Nicolas Barbian, Esther Ventura-Medina

"Mineral froth flotation is one of the most widely used processes to separate particles of valuable mineral from its associated gangue. It involves the selective separation of the hydrophobic particles from the slurry into the froth. The hydrophobic particles attach to the air bubbles and rise up to the froth phase on top of the slurry. The valuable mineral is collected when the froth overflows the cell wall. The separation performance of the process can be linked to the amount of solids and valuable material loaded on the bubble shells. In addition, it is well known that in most mineral systems, the presence of solids can enhance the stability of the froths. How the solids get to be distributed and what proportion is actually attached and stabilising the bubbles is not well known.This study aims to establish the relationship between operational variables, solids loading on bubbles and flotation performance. For this purpose, a series of industrial experiments to sample the solids in the bubble films under different operational conditions were carried out in two copper concentrators under steady state conditions. Samples of the lamellae were taken by touching the top surface of the bubbles with a glass slide. The amount of solids and liquid per unit area in the bubble lamellae can subsequently be estimated gravimetrically and by image analysis. The grade of the attached particles was also measured by adequate sampling. This gives an indication of the maximum grade that could be achieved from the process under the operating conditions."

Jan 1, 2003

By L. Burdukova

In flotation, depressants are used to reduce the amount of gangue that reports to the concentrate and hence increase the selectivity of the flotation process. At the University of Cape Town extensive batch flotation tests are carried out to evaluate industrial depressants and standard procedures have been developed over the years. This study was conducted in order to develop an improved method for comparing depressants using machine vision as an aid. The modified method of batch flotation involved a test with prolonged intervals between scraping to allow more time for the froth to build up and mature.

Jan 1, 2003

By P. N. Mohan Das, K. Harikrishna Bhat

"The major ilmenite reserves are located in India at Chavara (CH), Manavalakurichi ( MK) and Chatrapur, Orissa (OR). India stands first in terms of ilmenite reserves, which are estimated to be 278 million tonnes out of which, 142 million tonnes are processable. Mineralo-chemical analysis showed that Chavara ilmenite is the most weathered one with about 60% TiO2 while Chatrapur is the least weathered with about 50% TiO2. XRD and SEM studies of different magnetic fractions of these three mineral deposits established the co-existence of ilmenite with pseudorutile, rutile and haematite phases in substantially varying amounts. It is observed that the tropical weathering rather than the source rock difference has apparently played an important role in imparting major compositional and structural dissimilarities among the ilmenites in different places. Further, the chemical analysis, XRD and SEM characterisation of differently weathered samples of MK ilmenite separated by the magnetic fractionation showed that the degree of alteration was invariably associated with the decrease in magnetism, increase in the rutile phase and the change in Fe2+/Fe3+ ratio of ilmenite grains. Magnetically separated fractions when subjected to metallisation with carbonaceous reductant such as coke showed that the degree of reduction increases with the degree of alteration and with the decrease in the Fe2+/Fe3+ ratio.In the processing of ilmenite through the Becher process, aeration rusting of pre - reduced ilmenite is found to be the rate-limiting step thus, affecting the productivity and economy of the process. Investigations have proved that the addition of some organic compounds such as glyoxal, sucrose etc., to the system accelerates the reaction to such an extent that the rusting time has been reduced to less than half. The formation of acids by the these organic compounds during the rusting reaction was proved responsible for maintaining the pH of the solution in the range 3-4 at which iron hydroxide do not precipitate and block the pores in the reacting surface of the grain."

Jan 1, 2003