Search Documents

By Kang N. Zhong, Hui H. Luo, Yi H. Wei, Yu L. Wang

"More than 85% of phosphorous reserves in China occur as middle-low grade phosphate of sedimentary origin. The main gangues are dolomite, quartz, silicates, and clays. The characteristics of minerals are finely disseminated. Flotation results have shown that the floatability of apatite of this kind of ore is much worse than that of igneous and metasedimentary origin because of its high specific surface area. Although some effective depressants, such as naphthalene sulfonate and phenanthrene sulfonate, are used to decrease the MgO content in the P2O5 concentrate, its presence is still high (about 2%) in the Chinese concentrates. Meanwhile, the wastewater may cause some environmental problems. Batch flotation results and measurements of specific surface area and CO3 2- have revealed that there is a relationship between the floatability of apatite and the surface area.A two-stage flotation flowsheet, which includes a combination of direct and reverse flotation, was developed for beneficiating sedimentary phosphate ores. The direct flotation was conducted in an alkaline medium and most of the apatite and carbonate minerals floated leaving quartz and siliceous gangue in the sink. In the reverse flotation circuit, the floated product was further beneficiated in an acidic medium to eliminate the carbonate as a float product. Apart from the high quality of concentrate, the two-stage flotation also facilitated the treatment and the recycling of wastewater. A wastewater recycling procedure was developed and tested in a continuous flotation process. The key factor was the careful selection of effective and non-toxic reagents."

Jan 1, 2003

By R. Venugopal

Hydrocyclones have been used extensively for more than 100 years to classify mineral slurries for recirculation in grinding circuits. Sometimes hydrocyclone classification is carried out in more than one stage to improve the efficiency of classification. Factors affecting separation efficiency include fluid velocity, density, and viscosity as well as the mass, size, and density of the particles. The geometric configuration also affects its efficiency; it includes parameters like cyclone diameter, underflow and overflow diameter, position of vortex finder, height of the cyclone, feed inlet geometry, and diameter etc. Besides changes in the basic parameters some modifications in cyclone has also been introduced from time to time which have affected its efficiency, some of these are :-(i).Introduction of magnetic force along with the centrifugal and drag force to control the flow of the magnetic particles inside the chamber.(ii). Introduction of sparger, air is introduced in the chamber in the form of bubbles, to control the flow of fine particles and hydrophobic particles. (iii). Introduction of dilution technologies for the dilution of thickened underflow. (iv).Introduction of new model. In spite of wide use and simple geometry, the real working principle of hydrocyclone chamber is extremely complex because of the swirling turbulent flow inside the device. In order to get more knowledge about hydrocyclones and to increase its efficiency, past 10-15 years simulation techniques are being developed. The simulation models also enabled a deeper insight into the static and dynamic behavior of hydrocyclones. Therefore, more emphasis on simulations by methods like Computational Fluid Dynamics (CFD), Finite Element method (FEM) is given. Overall, a status review of the work carried out on the analysis of hydrocyclone performance, modeling approaches and its contribution in the efficiency of mineral processing operation is highlighted.

Sep 1, 2012

By R. S. C. Smart

Surface chemical factors, including the balance of hydrophobic (e.g. collectors) and hydrophilic (e.g. oxidation products, precipitates) species, are major control determinants in flotation rates of specific minerals and therefore grade and recovery. There are a number of challenges involved with the surface analysis of different mineral phases from process streams in a flotation facility. The first is to collect samples that are representative of the process and retain their surface chemistry prior to introduction into the instrument. The second challenge in studying the surface chemistry of specific minerals is to find reliable methods of mineral phase recognition. In surface analysis of mineral particles, confident mineral selection can be difficult with many multi-metal minerals and with precipitated, adsorbed, reacted and contaminant species in the outermost molecular layers. The third challenge is to provide a statistical surface analysis of multiple grains of the same mineral. Methods to achieve these aims are described. Principal component analysis (PCA) of ToF-SIMS data provides improvement in phase recognition, particle selection and associated variations in surface species. Specific examples from both lab and plant operations, demonstrate that this technique can be utilized to differentiate surface chemical factors promoting (hydrophobic species) or inhibiting (hydrophilic species) flotation. A study of copper ion transfer (inadvertent activation) from chalcopyrite to pyrite and sphalerite clearly identified a statistical difference in copper intensities between the sphalerite and pyrite phases corresponding to their flotation response. The PCA analysis applied to concentrate and tails samples collected from the Inco Matte Concentrator demonstrated extensive CuOH and NiOH transfer between chalcocite and heazlewoodite minerals. The statistical analysis has been able to identify mechanisms controlling recovery and selectivity. High intensity conditioning (HIC) tests in which sphalerite was separated from a complex sulfide ore gave a 5% increase in the overall Zn recovery. The PCA/ToF-SIMS statistical analysis revealed the discriminating depressant action of adherent aluminosilicate (gangue) fine particles and adsorbed ions on the surface of sphalerite grains. HIC conditioning resulted in the removal of these gangue fines improving surface collector attachment efficiency.

Jan 1, 2014

By Z. S. Abisheva

Rare and rare earth metals use quite often is an indicator of national economy development. The world structure of the rare-earth metals manufacturing countries in 2015 was presented as follows: China – 94.2%, India – 2.0%, Russia – 1.8%, the USA – 1.2%, Brazil – 0.5%, Malaysia – 0.3%. In Russia, large reserves of rare-earth metals, which reach nearly 28 million tons, are revealed. Kazakhstan, possessing a raw materials source of rare-earth metals, has all prerequisites for development of branch. Rare metals are manufactured in Kazakhstan incidentally by non-ferrous metals production. The production of indium, thallium, cadmium, selenium, tellurium, bismuth is made at the Ust-Kamenogorsk lead plant; tantalum, beryllium, niobium and molybdenum – at the enterprises of “National Atomic Company Kazatomprom” JSC. Production of a titanium, magnesium and vanadium is adjusted on “Ust-Kamenogorsk Titanium-magnesium Plant” JSC. Capacities for beryllic production yield are available on “Ulba Metallurgical Plant” JSC. The main producer of perrhenic production and osmium-187 is "Zhezkazganredmet" RSE. The single producer of gallium in Kazakhstan is “Aluminium of Kazakhstan” JSC; the capacity of enterprise is 25 t a year. In Kazakhstan innovative technologies for rare and rare earths mineral raw materials processing are created. The technology has been developed and a vacuum distillation apparatus has been created to purify crude selenium, which makes it possible to obtain a metal with a main component content of 99.9-99.99%. Technologies for processing of technogenic wastes and byproducts of the copper industry are developed. Implementation of technologies allow to obtain ammonium perrhenate, perrhenic acid, osmium isotope -187, tribasic lead sulphate, silver-concentrate. The technology of complex processing of black shales of Balasauskandyk deposit with the production of gold, vanadium, rare earth elements, uranium and ferrosilicon has been proposed. The processing was carried out using methods of autoclave leaching, sorption, extraction, precipitation. A highly profitable sorption technology for recovery of rhenium from solutions of underground leaching of uranium ores containing 0.2-0.4 mg/L of Re has been created. The organization of ammonium perrhenate production from solutions of uranium ore will significantly increase the volume of its production in Kazakhstan.

Jan 1, 2018

By William Skinner, Jennifer MacCarthy, Jonas Addai-Mensah, Ataollah Nosrati

"Acid leaching in agitated tanks is central to hydrometallurgical processing for valuable metals’ (e.g., copper, gold, nickel and cobalt) recovery from low grade (e.g., < 2 wt.%) ores. In this study, atmospheric leaching behaviour of Australian saprolitic nickel (Ni) laterite ore using sulfuric acid was investigated under isothermal, batch conditions at pH 1. The effect of primary process variables comprising time (4 h) and temperature (70 and 95 oC) on the leaching mechanisms and kinetics was established for -2 mm, low grade (~1 % Ni) saprolitic ore dispersions at 40 wt.% solid loading. Leaching proceeded incongruently, reflecting the proliferation of gangue minerals’ constituent elements (e.g., Mg, Al, Fe) alongside Ni and Co in the pregnant leach solutions (PLS). Subsequent analysis showed that 89% Ni and 78% Co were extracted after 4 h at 95 oC whilst at 70 oC the recoveries of these metals were markedly low (< 25 %). Overall, 177 and 644 kg H2SO4 /t dry ore were consumed at 70 and 95 oC, respectively. Activation energy of 79.0 ±1.0 kJ/mol was estimated for the mechanism of Ni and Co leaching and associated kinetics. Particles size analyses indicated that when the breakage of frail laterite particles due to shear is taken into consideration, differences in feed and leached product particle size distributions were insignificant , despite a remarkable increase in BET specific surface area of the product. Mineralogical analyses of the feed ore and leached solid products revealed a sub-crystalline silica phase enrichment of the latter. The overall results suggest that the mechanism of acid leaching of saprolitic Ni laterite may be described by a chemical reaction-controlled, shrinking core model."

Jan 1, 2014

By Xin Tan

In this paper, two types of low-grade complex zinc oxide ores (sandstone and limestone ores) from Yunnan province, China were investigated. A large number of argillaceous and alkaline gangue makes it infeasible to treat the ores with heap leaching. Although wet metallurgy can be considered, the lower efficiency of liquid-solid separation, the high cost, and low revenue limit this technology to be put into practice in large-scale. In order to solve this problem, a new technology combining mineral processing method with metallurgy technique is studied to process this refractory ore that consists of sandstone ore with 5.84 per centZn and limestone ore with 6.50 per centZn. The results of the tests showed that zinc can effectively be recovered from two types of the ores by using the new technology, and the acid consumption can be remarkably reduced. For sandstone sample, 82.96 per cent Zn was recovered by flotation and final Zn recovery by flotation+ hydro-metallurgy can be up to 78.17 per cent from the ore. In addition, for sandstone, acid consumption can be reduced from 270kg/t by direct acid, leaching to 76.92kg/t by flotation + hydrometallurgy combination. For limestone sample, 85.90 per centZn was recovered by flotation and totally 80.95 per cent Zn can be recovered by new technology which is a combination of mineral processing and metallurgy. Besides, H2SO4 consumption can be reduced from 450kg/t for sandstone originally to113.79kg/t after using new technology. One merit of this new process technology is that the zinc sulfides and oxides can be recovered without desliming in the flotation cells at the different stage and make sure the concentrate products as a good feed for hydrometallurgical technology. This study provided pretty good technical support for tapping low-grade refractory zinc oxide ores. Keywords: low-grade zinc oxide ores, limonite, non-desliming beneficiation, flotation + hydrometallurgy combination

Sep 1, 2012

By Y. F. Hou

This paper reports the results of the study of the influences of concentration and modulus of sodium potassium silicate solution (Na-K activator) and curing mode on the phase composition, mi-crostructure and strength development in the geopolymers prepared using Class F fly ash. X-ray dif-fraction (XRD), Fourier transform infrared spectroscopy (FTIR) and MAS NMR are utilized in this study. It shows that the compressive strength increases while sodium potassium silicate solution modulus increases, but when modulus exceeds 1.7, the compressive strength decreases, and it decreases markedly while modulus is greater than 2.0. The compressive strength improves with increase of sodium potassium silicate solution concentration. When the concentration is 36%, the compressive strength reaches the maximum. Elevated temperature can increase the strength of samples synthesized using sodium potassium silicate solution with 32% concentration and modulus 1.2. Compared to the strength of the sample cured at 50?, the strength of the samples cured at 65? and 80? are higher at 1 day and 3 days, but when cured at 80?, strength is smaller than that cured at 50? for 7 days. When temperature is too high, too long curing time will decrease the strength. Long precuring at room temperature before application of heat is beneficial for strength development, and there is about 10%~50% increase in strength of the samples cured at 1 day precuring and 2 days elevated temperature as compared to the strengths of the samples cured for 3 days at elevated temperature or cured for 28 days at room temperature. The main product of reaction in the geopolymeric material is amorphous alkali aluminosilicate gel.

Jan 1, 2014

By C. G. Anderson

Industrially proven and applied nitrogen species catalyzed (i.e. NSC) acidic pressure leaching has been utilized to treat a number of ores, concentrates and recycled materials. This versatile technology offers many advantages including low temperatures, low pressures, low capital costs, low operating costs, faster throughput and less costly materials of construction than conventional pressure oxidation. This paper will elucidate the application of this technology for production of gold, silver, palladium, rhodium, zinc, germanium, gallium, cobalt, copper, molybdenum, rhenium and nickel. Recycled material applications will also be elucidated. In addition, details of an application for treatment of a refractory chalcopyrite copper and gold bearing ore will be presented and pertinent economics discussed.

Jan 1, 2014

By T. Moloane, C. Bergman, Heloise Thiele

"A pilot test campaign was undertaken to evaluate dense medium cyclone separation efficiencies on samples of iron ore fines (-1mm +300µm). Evaluations were done using both gas and water atomised FeSi types across a range of operating conditions in the presence of slimes build-up. A Mineral Liberation Analyser (MLA) was used to measure size, density, shape and liberation data of DMS feed and products. The results of the test work were used to obtain parameters for modelling of the partition size/density response. The findings indicated that accurate density characterisation of the feed ore is essential in understanding product quality and recovery, particularly due to the effect of porosity and micro-inclusions. A significant off-set between cyclone underflow density and separation cut-point (D50) was found indicating that relatively low feed media densities (about 3.4g/cm3) are required to achieve high density cutpoints of over 4.0g/cm3. In agreement with CFD modelling, the separation quality is dominated by viscous effects, hence FeSi type and slimes content will need to be carefully controlled to ensure efficient separation.INTRODUCTION In the South African context, future resources of hematite are expected to be both of lower head grade and will contain a higher content of banded iron formation (BIF) (1). These ores may require finer crushing in order to liberate the high-grade fractions and will thus increase the amount of -1mm material to be processed. In order to efficiently upgrade these materials, it becomes necessary to re-examine both traditional and novel processes to treat material finer than 1mm in size. These include spiral and up-current classifiers, wet high intensity magnetic separation processes, Reflux classification and potentially includes dense medium separation (DMS). This study presents a technical evaluation of fines DMS using a mineralogically-based particle tracking analysis method (PTA) to calculate efficiencies of separation."

Jan 1, 2018

By Ye Chen, Jianhua Chen, Meng Liu, Yuqiong Li, Xiao Mu, Cuihua Zhao

"Sulfidization-amine is the most effective method for the recovery of smithsonite (ZnCO3), however the interface interaction details remain unclear. The sulfidization-amine flotation mechanism of smithsonite has been studied by Density Functional based Tight Binding (DFTB+) method in this paper. The slab model of ZnCO3 (101) surface was built and the adsorptions of a monolayer of HS- and S2- ions were conducted to model the sulfidization effect on the ZnCO3 (101) surface adsorption. DDA hardly interacts with the hydrated ZnCO3 (101) surface. Under the low concentration of Na2S, HS- ions form a Zn-SH-SH structure on the ZnCO3 (101) surface, which hinders the interaction between DDA and surface Zn atoms. Under the high concentration of Na2S, a layer of ZnS is formed on ZnCO3 (101) surface, which is favorable for the adsorption of DDA on the surface. This is consistent with the flotation practice where smithsonite flotation requires a large amount of sodium sulfide. The results could provide a microscopic investigation into the sulfidization-amine flotation mechanism of smithsonite.INTRODUCTIONSmithsonite (ZnCO3) is an important and typical oxide mineral of zinc. It is a semi-soluble salt mineral with a solubility product constant of 1.46 × 10-10 (Weast, 1973). The most common and effective method to recover oxidized zinc ores is froth flotation (Caproni et al., 1979; Pereia and Peres, 2005; Kashani and Rashchi, 2008). It is well known that the flotation of oxidized zinc minerals is much more difficult than the flotation of zinc sulphide minerals (Hosseini and Forssberg, 2007).The recovery of zinc oxide ores with poor floatability attracts more and more attention due to the depletion of easy-recovered of zinc sulfide ores.Sulfidization-amine flotation, which using Na2S as sufidizing agent and amine as collector (Mckenna et al., 1949; Rey, 1954; Abramov, 1961; Rey, 1979; Hosseini and Forssberg, 2007). This method is the most successful technology used for zinc oxide minerals flotation in large-scale industrial applications since it was invented in the 1950s (Önal et al., 2005; Pereira and Peres, 2005). There have been numerous experimental researches on the sulfidization-amine flotation of smithsonite. Shi et al., (2013) studied solution chemistry of smithsonite flotation system. Feng and Wen (2017) studied the formation of zinc sulfide species on smithsonite surfaces and its response to flotation performance. Wu et al., (2017) investigated the sulfidization behavior of smithsonite with the use of zeta potential, inductively coupled plasma (ICP), scanning electron microscope (SEM), and X-ray photoelectron spectroscopic (XPS). Their measurement results confirms the chemisorption of sulfur ions and the formation of ZnS film on the smithsonite surface after Na2S treatment, however the influence of HS- ions on the surface and the influence of sulfidization on the amine adsorption have not been discussed."

Jan 1, 2018

By D. Y. Liang

Rare metal ores have those features of high industrial value and bad performance in ore separation. Most of rare metals ores are with low grade of valuable components, rareness of useful minerals, complicated combination of associated minerals and high difficulty in separation and enrichment of minerals. For those single (Ta, Nb) or (Ta, Nb, Sn) ore occurred in granite and pegmatite, the ways of gravity separation and magneto electric separation to concentrate (Ta, Nb) minerals are adopted. There are many mines being explored successfully both at home and aboard. While, for complex (Nb-Zr-REE) ores associated with Be and Ti minerals, they are commonly considered as rich rare metals ore but more difficult to process. One of rare metals mine in Inner Mongolia has the features as with large reserves and high grade of columbium and zirconium and accompanies with REE and beryllium, therefore with significant industrial value. After the utilization of research method of process mineralogy, detailed mineralogy research has been made on the rare metals ore. The test results show that there are abroad isomorphism replacements among such elements, such as Ti, Mn, Fe, Nb and Ta, between Be and REE in metallic oxide minerals of that ore, which makes the mineral composition of that ore extremely complicated. This research identifies clearly the mineral composition, and investigate at the technological property and the occurrence of those elements as Nb, Zr, Be and REE in the rare metal ore. The achievements of this research provide important mineralogy basis for ore dressing research of refractory rare metallic ores.

Jan 1, 2014

By Duong Huu Hoang, Nathalie Kupka, Urs A. Peuker, Martin Rudolph

"The froth ability, froth stability and the froth structure are strong influences in flotation process i.e. on water recovery, bubble size, entrainment of gangue particle, flotation rate constants, grade and recovery. The labscale flotation of rich apatite ore with a high mass pull leads to significant changes in pulp and froth properties over time. The froth stability decreases with increasing the flotation time. These changes can be related to different solid contents, reagent concentration, froth heights and bubble size distributions. This study presents the results from froth studies and discussions on the particle size of fully liberated silicates and degree of entrainment based on automated mineralogy size-by-size analysis. The change of entrainment in a rich apatite ore batch flotation with time will describe more precisely by measuring froth properties using a Dynamic Foam Analyzer. It is concluded that the degree of entrainment is not only dependent on particle size but also the pulp density due to its effect on particle settling and also froth properties in varying resistance to particle drainage. Furthermore, entrainment models are applied to predict the effect of size, flotation time on entrainmentINTRODUCTIONFroth flotation belongs to the group of heterocoagulation separation techniques. Froth flotation is classically divided into two active zones, the pulp zone (where particle collection occurs) and the froth zone. A schematics drawing of the interaction between both zones is plotted in Figure 18 (Yianatos and Contreras, 2010). In froth flotation, the collision probability in the collection zone is governed by the physics of the process or hydrodynamics (Wills and Finch, 2016). The true flotation event in the pulp occurs when the hydrophobic valuable mineral particles collide with bubbles and formation of a stable particle-bubble aggregates moving upwards against gravity to the froth phase (Yianatos et al., 2009)."

Jan 1, 2018

By Z. Y. Lan

Bioleaching of marmatite with various mixed cultures of microorganisms was investigated. The experiments were carried out in shaking flasks with iron-free nutrient and the pulp density of 10% wt/vol at the temperature of 30?. The results show that zinc is preferentially leached before iron. The leaching rate of zinc with the mixed culture of Acidithiobacillus ferrooxidans, Acidithiobacillus thiooxidans and Leptospirillum ferrooxidans is 62% in 18 days. The leaching rate of zinc with the mixed culture of Acidithiobacillus ferrooxidans and Acidithiobacillus thiooxidans is nearly the same as that with the mixed culture of Acidithiobacillus ferrooxidans and Leptospirillum ferrooxidans (45% versus 50%). SEM and EDX analysis of the leaching residues indicate that a solid product layer composed of iron sulfide, elemental sulfur and jarosite accumulates in the mineral surface and becomes a barrier to the dissolution of marmatite. The bioleaching of marmatite follows the shrinking core product layer model. When the product layer increases and becomes insoluble, the leaching rate is controlled by the diffusion through the product layer and slows down. When the product layer decreases or becomes a porous layer, the leaching rate is controlled by chemical reaction and enhanced dramatically.

Jan 1, 2014

By L. Q. Luo

SHP-F3200 wet high-intensity magnetic separator (HIMS) was successfully used to separate the complex and weakly magnetic iron ores being composed of specularite, limonite and siderite in Ji-uquan Iron and Steel (Group) Co Ltd (JISCO). It is more and more difficult to separate iron ores from gangues, such as quartz, jasperite and phyllite, as the properties of iron ores gradually become more complicated and refractory. Some technologies have been used to improve SHP-F3200 HIMS, including modifying angle of magnetic polar from 90°to 83°, cooling exciting coils by oil instead of air, adding reverse-washing device to wash off magnetic particles, adjusting the tooth-space of matrix from 5.0 mm to 3.5 mm or 2.5 mm, so as to enhance the recovery of fine iron ore particles. It is still difficult to meet the requirement for recovering more difficultly-separated iron and the demands for high-grade concentrate of iron. In this paper, after analyzing magnetic force exerting on iron ore particles within different separating sections of SHP HIMS, it is proposed to apply the flowing-film technique into the HIMS. Thus a new-type LY matrix is designed to form magnetic gradient vertically, combined with a special flowing-film feeder to improve the existing SHP HIMS. The moving pattern of magnetic particles in pulp in HIMS separation district also has been analyzed in this paper. And the test on the SHP-F700 HIMS shows, under the condition of iron ore containing 30.52% Fe, with particle size of ?0.074 mm accounting for around 75%, if applied with flow-film technique, the iron recovery will be up from 69.45% to 76.07%, by 6.62 percent, with the same grade of concentrates of iron. The calculation of iron yield of every size fraction and the tests showed that film magnetic separation (Film-MS) could promote the iron yield of each size fraction, denoting an excellent result of application of the film technique to SHP HIMS. The mechanism of the film magnetic separation technique is to convert the turbulent flow and disordered movement of dynamic mass particles in the pulp into a directional and ordered laminar flow along the surface of tooth plate so as to strengthen the separation effects.

Jan 1, 2014

By Longjiang Li, Mao Jiang, Zhihui Shen, Guizhou University, Yin Pan

This paper aims to study the influence and action mechanism of collector Y-89 on the flotation of auriferous pyrite. The measurement to identify adsorption quantity, IR and XPS spectrum analysis and flotation experiment made on the pure mineral were conducted. The research results show that when the dosage of MIBC is 20 mg/L, and pH of 8, the dosage of Y-89 over 60 mg/L, the pyrite recovery rate is greater than 80%.And when the dosage of Y-89is 60 mg/L, dosage of MIBC 20 mg/L, the pH in a wider range (pH=4~9), the recovery is greater than 75%. When the pH is above 10, the pyrite is depressed and its recovery rate is found to be dramatically dropping. Adsorption quantity measurement also shows that the strong alkaline conditions inhibit the adsorption of Y-89 on the surface of auriferous pyrite. IR measurement indicates that chemisorption of Y-89 occurs on the surface of auriferous pyrite. XPS spectrum analysis indicates that without adding Y-89, oxidation reaction occurs on the surface of pyrite. But when Y-89 is added, the chemical environment of Fe on the surface of pyrite has changed. Such findings indicate that with Y-89, chemisorption occurs on the surface of auriferous pyrite.

Jan 1, 2014

By A. V. Byvaltsev

Adsorption of cyanide complexes of gold, silver, copper, mercury, nickel, cobalt, iron, zinc and cadmium has been studied. Adsorption isotherms of the mentioned metals from individual solutions for different free cyanide concentrations have been obtained. Values of the constants of Freundlich isotherm equation have been calculated. Metal cyanide complexes affinity to activated carbon was determined.

Jan 1, 2014

By B. P. von der Heyden, P. Neethling, M. Tadieb, L. Babedi

The effects of trace element substitutions in sphalerite mineral structure on optimised floatation response have, as yet, not been fully constrained or fully understood. To further this important field of study, this contribution focusses specifically on mineral and surface chemistry, and electro-chemistry of Cd- and Co- substituted synthetic sphalerites using Raman spectroscopy and Zeta potential experimentation. Raman spectroscopy illustrates that the presence of these impurities results in the introduction of a new mode, the relative intensity of which can be correlated (Cd r2=0.95 and Co r2= 0.99) to the dopant concentration. Comparison to X-ray Diffraction results measuring the unit cell parameter further shows that this relative intensity (Cd r2=0.81 and Co r2= 0.99) may provide insights into the degree of lattice strain within the mineral structure. The zeta potential distribution of an un-activated Cd-sphalerite show no detrimental effect as function of Cd content. Although the iso-electric point shifted from 2.45 at 1 wt.% Cd to 2.69 at 3.68 wt.% Cd, the zeta potential remained negative at alkaline media. Conversely, cobalt at low concentration of 0.36 wt.% had a detrimental effect on the surface charge, resulting to a close to neutral zeta potential at different pH. The adsorption of Cu ions on the surface of Co-bearing sphalerite conditioned in an alkaline media slightly increases the zeta potential of Co-sphalerite. While the Cd-bearing sphalerite decrease in negative zeta potential at >1 wt.% Cd indicating a complete exchange between Cu and Zn. The results presented herein illustrate that, based on the chemical nature of the substituting metal; sphalerite will exhibit multiple response to flotation reagents. Maximum recovery of zinc can thus only be achieved through multidisciplinary study and fundamental understanding of the effects of cation substitution on mineral structure and surface chemistry, the latter necessarily affecting the floatation response.

Jan 1, 2018

By A. S. Choudhary

Most of the coal reserves in India are of drift origin and have very poor washability characteristics and a high level of near gravity materials. At least 30 new coal wash plants are expected to be set up in the next 5years.In such a scenario, adequate sampling followed by sink float test work for washability analysis becomes very critical for designing these new plants. For coal sampling purpose, stipulations of different standards are sometimes formidable and on the border of ?impracticality?; sometimes are self contradictory in terms of gross sample weight vis-a-vis minimum number of particles required in each size fraction and in each relative density fraction and also the minimum mass in the latter. Validation of the generated data is another important aspect of washability analysis. These issues can easily be addressed by using straight forward mathematical relationships, well known RR plots and by using simple MS Excel tool, etc.

Sep 1, 2012

The ore studied occurred in the Three Rivers area in China and was a silver-lead-zinc complex ore containing 400.52 g/t silver, 4.77 % lead and 3.47 % zinc. Silver, lead and zinc were the major valuable elements in the ore and copper, cadmium and tin were the associated elements to be comprehensively recovered, whereas arsenic was the harmful element. The element silver occurred mainly in freibergite with small proportion in dyscrasite and other silver minerals. The carrier minerals for silver were mainly galena and oxidized lead minerals and then sphalerite, arsenopyrite and pyrite. The ore contained numerous minerals with complex mosaic texture and the lead and zinc minerals enclosed each other multiply, which made the separation of the minerals in the ore very difficult. Experimental investigation on the beneficiation of the ore indicated that with flotation separation process it was very hard to obtain single lead concentrate or single zinc concentrate that would meet the requirement of market. In the meantime, during the separation process of lead and zinc, silver tended to be dispersed, resulting in a low recovery of silver. Therefore, a rational utilization technique for the ore should be a combined process of bulk flotation to reduce arsenic? sulphating roasting of silver-lead-zinc bulk concentrate-leaching with diluted sulphuric acid to separate silver, lead and zinc. With this process quality lead concentrate containing silver and high grade zinc product and silver product could be obtained. The recovery of silver, lead and zinc in flotation was 85.10%, 84.48% and 82.48%, respectively. The total recovery of silver, lead and zinc in chemical processing was 97.07%(sum of recovery of silver ingot and lead concentrate), 99.61% and 90.93%, respectively.

Jan 1, 2014

By S. N. Shahcheraghi

Bioleaching method makes use of bacteria in solving metallic sulphides, so that these bacteria tend to convert insoluble metal sulphides into soluble sulphates. Since the kinetics description of this process is inevitable for better interpretation of relation between metabolism and growth of live organisms, as well as optimization of metals extraction processes, in this paper, this description is represented and designed in mathematic (kinetics) model for copper sulphide minerals based on Monod kinetics model. According to this model, special growth rate of bacteria (?) is a hyperbola function of restrictive substrate concentration (S). By Solving and developing of Monod kinetics model, a comprehensive kinetics model for bioleaching of copper sulphide minerals results. The designed is also applicable for other metal sulphides.

Sep 1, 2012