Search Documents

By Pathik Deb Mallik, Shyamal K. Mitra, Rajiv Kishore, Shuvranshu Rout, Manos De

"This paper presents a case study on the design and construction of a deep underground pit structure constructed inside almost a century old existing plant building. The complexity and challenge for the design and construction lay in executing the work in a difficult subsoil condition especially the presence of deep mica schist. The limited space availability in the existing plant for construction work without hampering regular production in other adjoining areas of the plant made the execution more challenging. Experience with difficult subsoil and proximity to old foundations entailed a non-conventional engineering approach while ensuring complete safety in spite of maintaining the normal operation.INTRODUCTIONTata Steel Processing and Distribution Limited (TSPDL) is a subsidiary unit of Tata Steel Limited (TSL) having a CR processing facility inside the premises of Tata Steel Limited. TSPDL intended to install equipment for a new slitting line inside the existing shed including construction of very deep structure called “loop pit” where the strips from cut CR sheets collect in the form of loops and are recovered as scrap. The entire plant is located within the shed of existing plant. The construction of all foundations including the loop pit is to be executed in the limited area without disturbance to normal production work in balance areas of the plant and also maintain safety and integrity of existing structures.The existing shed is an old structure constructed approximately 80 years ago. The building column foundations are gravity type design of brick masonry supporting only the vertical load from the columns. This type of foundation designed with no eccentricity of loading provides no allowance for implementing any foundation stabilizing design. The present project required civil construction for the new equipment foundations safely within this area."

Jan 1, 2015

By Jin-Wei Huang, Bradley J. Fleming, Sri Sritharan

"Although soil improvement and its application to deep foundations is gaining popularity in the engineering community, this technique is not widely used in high seismic regions due to lack of fundamental understanding of both the behavior of improved soils under high-strain cyclic loading and the interactions between the pile, improved soil, and unimproved soil. This paper describes part of an ongoing Network for Earthquake Engineering Simulation (NEES) project, where two identical full-scale steel pipe piles were driven at a soft clay site in Oklahoma. The soil surrounding one of these piles was improved using the cement deep soil mixing technique in order to enhance its lateral load behavior. Both piles were tested for seismic resistance using dynamic and quasi-static loading.The pile in unimproved soil provided larger displacements with limited lateral force resistance. This pile was subjected to lateral displacements of up to 400 mm, but experienced minimum inelastic actions. On the other hand, the pile in improved soil reached its lateral capacity at a displacement of 100 mm, at which point the critical region at the base of the pile just above the improved ground experienced buckling and fractured due to low cycle fatigue. Compared to the pile in unimproved soil, the improved ground increased the system strength by 42%. Although the soil was improved over 2900 mm, the effective improvement depth was approximately 1300 mm below the ground surface.In this paper, it is demonstrated that the effects of block type soil improvement of limited horizontal and vertical dimensions can be described using a simplified theoretical approach involving a modification to the well-known p-y representation of soil response. An example using this method is presented and shown to give adequate support to a standard 12-inch diameter steel pipe pile embedded in soft soil,IntroductionPilings are the preferred foundation support for many civil engineering structures including highway bridges, railroad bridges, and port wharves. These structures and their foundations are subjected to forces created by earthquakes, wind, waves, water current, vessel impact, ice, and gravity. All loads applied to the superstructure must be transmitted to the foundation where they are resisted by the surrounding soil. With significant lateral loads, use of pile foundations may be the only solution to transmit large structural loads to competent soils. Piles supported by competent soils are relatively easy to design and costs are often attainable. However, thick layers of weak soils such as soft clays are widespread in high seismic areas (e.g., San Francisco, southern Nevada, Washington, Eastern Missouri, and Arkansas), exacerbating design challenges. Soft clays reduce the lateral resistance of the pile-soil system, making the pile foundation less cost effective. In this case, the current design practice is to use an increased number of larger diameter piles, which is a costly alternative (see SDC, Caltrans 2010). An innovative and more cost-efficient solution to this problem is to improve the soil within a short depth surrounding the foundation, thereby increasing its lateral stiffness. Some well-known methods for improving soil include deep soil mixing, stone columns, and simple soft soil replacement with select granular material."

Jan 1, 2017

By William M. Dalrymple, William P. Owen, Benjamin S. Rivers

For the California Department of Transportation (Caltrans), geophysical applications have played an important role as part of a successful multidisciplinary approach to subsurface characterization for the design of high value structures. Since at least the 1950’s, geophysical methods have been deployed to guide the exploration drilling program and to maximize the return on drilling investment by increasing the amount of data obtained from test borings. Geophysical applications saw increased use beginning in the 1990’s, during the seismic retrofit of the state’s toll bridges and the replacement of the west span of the San Francisco-Oakland Bay Bridge. Over the intervening years, increases in computing power and increasingly sophisticated commercial off-the-shelf software applications have allowed Caltrans to leverage advancements and perform geophysical investigations of increasing complexity and scale. Ultimately, the goal of these efforts is to maximize return on investment, whereby increased investigation costs at the design phase are offset by reduced uncertainty regarding subsurface conditions, leading to reduced cost overruns related to change orders and unforeseen site conditions during construction. These objectives are consistent with the recent Every Day Counts (EDC) initiative to incorporate Advanced Geotechnical Methods in Exploration (A-GaME) into routine engineering practice. Caltrans is an implementation partner of the A-GaME initiative, and Caltrans’ practices represent a model toward the institutionalized geophysical site characterization practices for other transportation organizations. The authors provide a retrospective on 70 years of experience with geophysical applications for transportation infrastructure, with examples and observations on potential future direction of the industry.

By Nadir Ansari, Brian W. Wilson, Marina S. W. Li

"A hybrid Deep Mixing (DM) shoring system was recently constructed for a high-rise development in downtown Vancouver, British Columbia, Canada for the temporary support of a five-level basement excavation. The site is bounded by an existing bridge off-ramp structure along its longest side and by city streets on the other two sides, which formed a truncated triangle in plan. A conventional secant pile wall was installed along the longest side, about 380 ft (116 m) in length, of the site. Hybrid shoring walls (HSW) 1 and 2 were installed along two shorter sides with each being 235 to 246 ft (72 to 75 m) long. HSW 3 completed the excavation support system along the shortest side with a length of about 55 ft (17 m). Cutter soil mixing (CSM) was proposed by the excavation and shoring design-build team in lieu of conventional secant piling. CSM was the preferred method to construct the infill panels between soldier piles because of the speed at which the shoring system could be constructed in the variable fill, peat, wood waste and overburden. Design ConsiderationsTo minimize the impact on buried utilities along the outside perimeter of the excavation, the temporary shoring was designed to limit the lateral displacements to less than 0.8 in (20 mm). Factors taken into consideration for shoring design included the lateral earth pressures from the fill and native soils, groundwater pressures, temporary construction loads (e.g., crane or heavy plant/equipment), and permanent structural requirements. The subsurface conditions at this site typically consisted of fill (cohesive and granular), overlying peat and/or wood waste, overlying clayey silt to sandy silt, overlying weathered to dense to very dense clayey silt till to sandy silt till with silt layers. Localized, perched groundwater was observed within the fill, peat, wood waste and sandy silt layers above the dense till."

Jan 1, 2017

By Charles M. Wilk, Lori Tiefenthaler

"Information presented in this paper can be used to support deep soil mixing, subsurface grouting and slurry wall technology as sustainable construction technologies. Ordinary Portland Cement (OPC) is the default cementitious material used by Deep Foundation Institute (DFI) Members for geotechnical work. Owners, engineers and contractors can contribute to the sustainability of a geotechnical project by increasing the use blended hydraulic cements and industrial byproducts to replace some of the OPC in mix designs. Sustainability is defined as the quality of not being harmful to the environment or depleting natural resources. Production of cementitious materials consumes natural raw materials and energy while also generating air emissions and waste. Life Cycle Assessments can be used to compare the relative environmental impacts of one cementitious material to another. Blended hydraulic cements (BHCs) are interground (or blended) mixtures of Supplementary Cementitious Materials (SCMs) with OPC. Commonly used SCMs include fly ash, ground granulated blast furnace slag (GGBFS) and limestone. Examples of industrial byproducts commonly used in geotechnical work include coal combustion residuals (CCR) (aka fly ash), and ground granulated blast furnace slag (GGBFS). Much of life cycle impact of these SCMs and industrial byproducts have already been borne by the industries that generated them. There is increasing awareness to LCA and sustainability of different materials used on projects. This is evident in the application of the Leadership in Energy and Environmental Design (LEED) program. The savings in environmental impact with the use of SCMs and industrial byproducts can make proposed use of these materials in a geotechnical project more attractive in terms of sustainability. This paper presents (a) information that compares published life cycle assessment data of OPC, BHCs, and slag cement (SC) to illustrate the potential benefits to sustainability and (b) general strategies for positioning a geotechnical application, use, project design or cementitious material mix as a more sustainable alternative"

Jan 1, 2017

By Jonathan J. Dewsbury

It is argued that approximate computer based methods are only suited to modelling conventional piled rafts, for pile enhanced rafts where the interactions will be non linear three dimensional finite element analysis is required. However current 3D finite element analysis often relies on symmetry to reduce computational cost and there are concerns over the dependency of the results on the user. Therefore a new strategy within the finite element framework has been proposed. The main advantage of this strategy is that each stage of the model can be checked for consistency. There is also the added benefit that non symmetrical models can easily be constructed by tying the validated components together without dramatic increases in computational time. The proposed strategy compared well to the published results of a hypothetical example of a piled raft previously analysed with numerous methods by Poulos et al. (1997).

Jan 1, 2010

By Howard A. Perko, Margaret Dring, Gerald Verbeek, Scott Slaughter

Helical piles have become a widely used deep foundation system in recent years due to their many inherent advantages. The cone penetration test (CPT) is commonly used in geotechnical practice to evaluate subsurface conditions for deep foundation design as the method provides a continuous soil profile in a short amount of time, measures in-situ soil strength, and in many ways behaves similar to a “mini pile” during penetration. In the CPT test, an instrumented cone is hydraulically advanced into the soil at a constant rate. As the cone is advanced, strain gauges embedded in the cone body continuously measure the tip resistance and side friction. In addition, a piezometer element is commonly used to measure the (dynamic) pore water pressure in the soil as the cone is advanced. A study was conducted comparing the CPT tip resistance to helical pile installation torque and capacity. In this paper, the outcome of this study was compared with historical data of helical pile installation torque records, static analysis predictions using commonly used techniques, and pile load test results over a wide range of soil conditions. A literature review was also conducted where a comparison was made for CPT tip resistance and helical pile installation torque data with previously published correlations.

Sep 8, 2021

By Bradley J. Fleming

Although soil improvement and its application to deep foundations is gaining popularity in the engineering community, this technique is not widely used in high seismic regions due to lack of fundamental understanding of both the behavior of improved soils under high-strain cyclic loading and the interactions between the pile, improved soil, and unimproved soil. This paper describes part of an ongoing Network for Earthquake Engineering Simulation (NEES) project, where two identical full-scale steel pipe piles were driven at a soft clay site in Oklahoma. The soil surrounding one of these piles was improved using the cement deep soil mixing technique in order to enhance its lateral load behavior. Both piles were tested for seismic resistance using dynamic and quasi-static loading. The pile in unimproved soil provided larger displacements with limited lateral force resistance. This pile was subjected to lateral displacements of up to 400 mm, but experienced minimum inelastic actions. On the other hand, the pile in improved soil reached its lateral capacity at a displacement of 100 mm, at which point the critical region at the base of the pile just above the improved ground experienced buckling and fractured due to low cycle fatigue. Compared to the pile in unimproved soil, the improved ground increased the system strength by 42%. Although the soil was improved over 2900 mm, the effective improvement depth was approximately 1300 mm below the ground surface. In this paper, it is demonstrated that the effects of block type soil improvement of limited horizontal and vertical dimensions can be described using a simplified theoretical approach involving a modification to the well-known p-y representation of soil response. An example using this method is presented and shown to give adequate support to a standard 12-inch diameter steel pipe pile embedded in soft soil.

By Dongwook Kim

Recently, load and resistance factor design (LRFD) is gradually being adopted internationally in geotechnical design due to the advantages of LRFD over the existing allowable stress design (ASD). LRFD is a more advanced design method compared to the ASD because resistance factor is calibrated based on the reliability analysis for a given target reliability index. Target reliability index changes with the importance of the structure. Typically, target reliability index of offshore foundation is less than those of onshore. The widely-used Imperial College Pile (ICP) design method is used for the calculation of pullout capacity of driven piles. The uncertainties regarding pullout capacities of driven piles are assessed using the statistical data reported in the literature. The first-order reliability method (FORM) is used to calibrate resistance factors for the pullout ultimate limit states of the driven piles for three different levels (2.5, 3.0, and 3.5) of target reliability index. The load factors used in this paper are the ones proposed in the AASHTO LRFD bridge design specifications.

Jan 1, 2010

By Abhijit Saha

"The stone columns improve the performance of foundations on soft and loose soil due to the ability of composite ground to sustain increased structural loads under reduced settlements. The interaction between the two basic elements: the ambient subsoil and installed column, present a complexity of behaviour, both in terms of applied stresses and resulting strains. Moreover, as the same is provided in-group in a regular array beneath foundations, the performance of an individual column is likely to be influenced by the presence of neighbouring columns. The present paper addresses this very issue. Analysis of reported field hydro-test data of large diameter oil storage tanks in soft ground in reference to some existing theories led to the development of the stone-column ‘group efficiency factor’. In order that such factor is of general use, it was felt necessary to examine the applicability of the factor to different sizes of groups under varied subsoil conditions. With this in view, some model test results reported in literature of single and group of columns have been analysed and in the process an explicit relationship regarding the stone-column ‘groupeffect’ could be established.INTRODUCTIONThe field application of the stone column technology has gained momentum than the intricate design methodology due to its simplicity in installation and intuitive performance. The ground improvement is due to the complex interaction within the ‘unit-cell’ comprised of the installed column in ambient ground under sustained vertical stress; in association with the interdependence of problem geometry and material properties of the two different soils-one 'native' and the other 'back-filled'. The beneficial effects are increased load capacity, reduction in total and differential settlements, minimization of post construction settlements effected by accelerating consolidation, reduced risk of soil liquefaction, aiding in improvement of slope stability of embankments and natural slopes and effecting changes in the dynamic response. The ‘unit-cell’ concept of a tributary soil cylinder encapsulating an installed column with some reasonable assumptions and boundary conditions (Aboshi et al, 1979; Balaam & Booker, 1981; Van Impe & De Beer, 1983; Priebe, 1976; Saha & De, 1994; Saha; 2005, 2006, 2007, 2011, Saha & Das; 2007) deals with the load-settlement behaviour of the composite system. The present investigation is based on published field data from literature & validated with experimental study reported in literature. The study addresses the effect of group interaction of stone columns beneath a large area loading on ground settlement. The hydrotest load-settlement data of 12 large diameter oil storage tanks founded on stone column reinforced soil at Haldia1 and Kandla2 refinery sites in India; reported by Som (1997), has been analysed to quantify the group efficiency. The results as obtained are compared with experimental study on 2, 3 and 4 stone column groups at different spacing-diameter ratios in soft clay3 reported by Rao et al (1997) to validate the above analysis. A unique relationship between the column spacing and group efficiency has been obtained."

Jan 1, 2015

By Steffen Schweizer, Tadeusz Brzozowski, Alfred Koller, Michał Topolnicki, Jürgen Wäger, Grzegorz Sołtys

A full scale test has been conducted to determine ground bearing pressure under rig tracks. The track loads were recorded in real time using Liebherr's Ground Pressure Visualisation system, and the vertical stress induced in the ground was measured with pressure cells embedded in the ground. It has been found that the recommendation of EN 16228 regarding determination of the track length is oversimplified. The contact length should dependent on the susceptibility of the working platform. It has been also demonstrated that the corrected pressure distributions under the tracks influence the dimensioning of the working platforms. As a result, the designed working platform may actually be less secure than is shown by conventional calculations.

May 1, 2022

By Joel Moskowitz, Jan Cermak

"New York City has unique geologic conditions which must be considered when designing pile foundations. Where shallow foundations are not feasible, the City's subsurface conditions require a variety of deep foundation systems, ranging from high capacity rock socketed piles, to piles end-bearing on bedrock, to friction piles bearing in alluvial or glacial deposits. Pile load testing is essential in confirming pile capacities as pile analyses include assumptions on soil and soil-pile response, and pile driving equipment. Load test results must be interpreted to estimate the long-term pile behavior. Except for lightly loaded driven piles, the New York City Building Code (the Code) requires that pile capacities be confirmed by static load testing. The Code provides the number of static load tests required, test procedures, and acceptance criteria. In the last few decades, methods other than static load testing have been developed including dynamic and rapid (pseudo-static) load tests. Recently, those methods have also been employed on several projects in New York City. The traditional approach to pile load testing in New York City is discussed herein including engineering involved in the analyses of test data with examples. In addition, several projects which included non-static load testing are discussed INTRODUCTIONPile load testing complements the subsurface information and pile design by providing further data on pile-soil interaction for the selected pile type and installation method. Traditional approaches to pile load testing in New York City involve static load tests to verify the design capacity of the piles for a given minimum factor of safety.In the late 1950's, Dr. Phillip C. Rutledge summarized his views on the philosophy of pile foundations in an unpublished, in-house document. He viewed pile foundations as good illustrations of pertinent and impertinent aspects of geotechnical engineering. In the analyses of piles he divided engineering into four general types:(a) Theoretical engineering in which decisions are made based on theoretical analyses. This represents ideal engineering, in which all factors affecting the pile design are well established or, at least, few simplifying assumptions with known effects on the analyses are made."

Jan 1, 2005

By Dan Brown

Improvements in construction equipment and techniques in recent years have made possible the use of drilled shaft foundations in diameters and lengths not previously considered practical or feasible. Many highway bridge and other structures are now routinely founded on drilled shafts which -are 8 to 12 feet in diameter and extending over 200 feet in depth below grade. There are unique challenges associated with constructing such large and deep cast-In-place foundations and engineers should be aware of the special needs associated with site investigation, construction specifications, material requirements, and quality assurance. This paper outlines a number of special considerations for these foundations, along with strategies that may be employed to improve the reliability and quality of large drilled shaft foundations.

May 11, 2007

By Mahesh Hingorani

Integrity issues for bored cast-in-situ piles have raised the need for the use of non-destructive tests to verify pile integrity and detect possible anomalies in installed pile sections that could adversely affect their serviceability. Integrity inspections performed after installations are often the most reasonable alternative available to assess the shaft quality. The two most common methods are pulse-echo from a small hand held hammer at the pile top, and cross-hole ultrasonic transmissions along the shaft between parallel sonic pipes. While different in technique, each method has its advantages and limitations. This paper emphasizes more on the degree of accuracy of low-strain pile integrity test by comparing the results with cross-hole sonic logging. Reliable data collection and interpretation by an experienced test engineer will reveal the integrity of the pile. Cross-hole sonic logging and low-strain pile integrity testing were both specified as quality control measures for a metro rail project in India. Both cross-hole sonic logging and low-strain pile integrity testing indicated defects in several bored piles. Also minor imperfections recorded by cross-hole sonic logging were observed in low-strain results. The observations of the two test methods are presented and compared for a better understanding of the importance of low-strain test results for any project. INTRODUCTION Cast-in-situ concrete piles are often chosen as a deep foundation alternative where challenging soil conditions exist. Although quality control measures are almost always taken during the installation of the piles, it is often difficult or impossible to confirm the integrity of the pile at this stage, particularly in wet conditions. Because of the relatively high probability of bored piles having anomalies, quality assurance of each bored pile is essential for each project.

Jan 1, 2019

By Jason Herron, Joseph Brown

The common couplings for joining sections of helical piles with an outside diameter of 6.625 inches and 8.625 inches are square on square, flange to flange, external pipe sleeve, internal pipe sleeve, and welded joint. Each coupling type has advantages and disadvantages in efficiency, capacity, installation, and economics of the installed pile. All these coupling types have been used in the helical pile market in North America for various applications and designs. Many of these applications require on-site testing, but test records are not typically shared with the helical pile industry. Due to the lack of information available for square on square and flange to flange couplings, testing was done to compare the efficiency of installation, load to deflection response, and torque to capacity ratios of external pipe sleeve, square on square, and flange to flange couplings. Field installations and tension tests were performed in non-cohesive (sand type) soil near Caseyville, IL and in cohesive (clay type) soil in Centralia, MO. The data collected during these tests included rotations per foot during installation, installation torque, applied pressure, and deflection. The results of this testing are analyzed and discussed within this paper. The results indicate that the square to square coupling is the most efficient of the designs tested, but this conclusion cannot be fully justified without further testing due to the variability in the data gathered and the small number of piles tested. INTRODUCTION A helical pile is typically assumed to be a medium-displacement pile when its outside diameter is between 4.5 inches and 8 inches and a high-displacement pile when its outside diameter is greater than 8 inches. A helical pile designer has multiple options when selecting a coupling type for medium- to high-displacement helical piles. Each type of coupling has advantages and disadvantages and must be analyzed on the bases of efficiency, capacity, installation, and economics of a project. Typical couplings that are chosen by designers include square on square, flange to flange, external pipe sleeve, internal pipe sleeve, and welded joint. A helical pile must transfer axial, lateral, bending moment, and torsional loads, and the coupling must be designed to effectively and efficiently transfer each type of load. During the installation of a helical pile, the rate of penetration and the disturbance of soil layers play a critical role in the efficiency and torque to capacity ratio (Kt) of the pile. It is common for a coupling to protrude beyond the outside diameter of the pipe section being used. This is necessary for the function of certain coupling types and can facilitate the connection of couplings. However, it causes increased soil disturbance and reduce the rate of penetration due to soil bearing against the protruding portion of the coupling. A helical pile designer typically will work to minimize the coupling protrusion and create a pile with optimal installation efficiency but may choose a design with lower installation efficiency if it offers sufficient economic advantage.

Jan 1, 2019

By Ramin Motamed, Fahim M. Bhuiyan, Raj V. Siddharthan, Joseph Toth

The difficulty in material characterization and the erratic response of cemented soil layers, such as caliche in the Las Vegas valley, creates challenges for practicing engineers to reliably predict the response of deep foundations. The focus of this paper is the numerical prediction of axial response in drilled shaft foundations, which are commonly used in infrastructure projects (i.e., bridges and tall buildings) in Las Vegas, NV. The prevalence of hard caliche layers with variation in the degree of cementation add to the complication in numerical modeling. In this study, the applicability of two existing t-z models, developed for Florida limestone and soft rock, was evaluated based on numerical simulations of three bi-directional load tests conducted at caliche-dominant sites. The corresponding top-down load tests were also simulated for further assessment. A MATLAB-based finite-difference program, NVShaft, has been used to implement the mentioned t-z models in axial load analysis. Complexity originating from drilled shaft construction and the interaction with caliche during one axial load test resulted in a stiffer predicted response compared to measure data. For the other two load tests, both t-z models produced comparable load-displacement responses. It was observed that the t-z model for Florida limestone predicted relatively stiffer responses and higher drilled shaft capacity.

Sep 8, 2021

By Howard A. Perko, Melinda J. Hummel

"Hydraulically jacked piles, herein referred to as jacked piles, are commonly used for underpinning existing structures to arrest settlement or augment an existing foundation for higher loads. They consist of steel pipe segments coupled together and jacked into the ground using a hydraulic ram. Pipe sections can vary in size from 3"" diameter to 18"" diameter or larger. Jacking resistance is typically provided by dead loads of existing structures. This type of piling system has been utilized for foundation underpinning, repair, and augmentation for more than 120 years, yet little has been published on the capacity, installation standards, and reliability of these systems. Pile load tests from a number of projects are presented and analysed. The data show that previous methods of jacked pile capacity and depth prediction are crude at best. Empirical relationships between capacity, depth, soil type, and standard penetration resistance blow count contain a high degree of scatter. Scatter in the data indicate capacity prediction for jacked piles needs further research and refinement.INTRODUCTIONPush pier, resistance pile, steel pier, and jacked pile are some of the names often applied to hydraulically jacked piles used for underpinning. The term ‘jacked pile’ is more common in building codes and will be used herein. Although jacked piles can be installed for new construction, this paper is focused on piles used for support of existing structures.Jacked piles consist of short segments of pipe or structural steel tube that are coupled together and forced into the ground using a hydraulic ram fastened to or beneath a footing, stem wall, or grade beam of an existing structure. In this way, the weight of the structure provides the resistance necessary to force the pile into the ground. A factor of safety can be achieved in design by redundancy, which is consecutively installing more than one jacked pile to support the same portion of foundation. Installing jacked piles consecutively using the same dead load and then releasing the load after each pile installation allows one to continue adding piles to the same general area until a total aggregate capacity is achieved to account for anticipated dead plus live loads and a desired factor of safety for that area.An engineering schematic of an example jacked pile connected to a footing foundation is shown in Figure 1. Modern jacked piles typically incorporate a steel bracket. There are many sizes and styles of brackets available. Some categories include plate brackets that bolt to the outside of an existing foundation wall, wide and narrow angle brackets that extend under existing footings, pin brackets for attachment to structural steel, and reverse angle brackets for attachment to footing and wall. Table 1 lists example brackets and their benefits."

Jan 1, 2017

By Timothy C. Siegel, Derrick Dasenbrock, Rich Lamb, Paul J. Axtell

"The axial resistance provided by deep foundations may be divided into two components: side resistance and tip resistance. The direction that the side resistance acts depends on the relative movement between the deep foundation and the adjacent soil. That is, when the foundation moves downward relative to the soil, then the side resistance is positive and acts upward. Conversely, when the soil moves downward relative to the foundation the side resistance is negative and acts downward. Research supports that both positive side resistance and negative skin friction develop in essentially all deep foundations. The side resistance distribution is a function of the soil strength and stiffness, the applied top loads, and whether the top load is sustained, transient, or a combination of sustained and transient loads. Consideration of drag load and downdrag has become more convoluted with implementation of geotechnical aspects into the AASHTO LRFD Bridge Design Specifications and its use of load and resistance factors. This paper examines the current AASHTO Specifications and presents an alternative design approach for drag load and downdrag using the LRFD framework. The alternative design approach is illustrated by two examples involving drag load and downdrag.IntroductionThe axial resistance provided by deep foundations may be divided into two components: side resistance and tip resistance. The direction that the side resistance acts depends on the relative movement between the deep foundation and the adjacent soil. That is, when the foundation moves downward relative to the soil, then the side resistance is positive and acts upward. Conversely, when the soil moves downward relative to the foundation the side resistance is negative and acts downward. Research supports that both positive side resistance and negative skin friction develop in essentially all deep foundations. The side resistance distribution is a function of the soil strength and stiffness, the applied top load, and whether the top load is sustained, transient, or a combination of sustained and transient.Consideration of drag load and downdrag has become more convoluted with implementation of geotechnical aspects into the LRFD Bridge Design Specifications and its use of load and resistance factors. This paper examines current LRFD design specifications and presents an alternative design approach for drag load and alternative design approach is applied to several examples where drag load and/or downdrag may control design."

Jan 1, 2015

By John C. Niedzielski

The PHX Sky Train is a five mile long automated people mover system located at Phoenix Sky Harbor International Airport. Phase I of the PHX Sky Train includes the design and construction of 227 drilled shafts supporting three stations and approximately 9,000 feet of elevated guideway. The guideway includes a 100 foot high, 330 foot long span extending over an active taxiway, which will be the first system of this kind over an active taxiway in the world. The soil conditions in this area generally consist of alluvial Sand, Gravel and Cobbles (locally known as SGC) deposited by the nearby Salt River. The foundation system will support relatively high axial loads, lateral loads and moments due to the height of the guideway above the ground surface, where it needs to pass over existing concourse walkways, bridges, a taxiway and buildings. Drilled shaft design involves designing 4.5-foot to 9-foot diameter drilled shafts within the SGC deposits, most of which extend well below the groundwater table. There is a high potential for collapse of drilled shaft excavation sidewalls within this material. Such extreme design loading conditions, together with difficult ground conditions at the site, result in several challenges for the design and construction of the deep foundation system for the guideway and stations. A load test shaft was designed and constructed as a means to provide site-specific measurement of axial performance under these difficult conditions. Results from the load test were used to reduce the size of the drilled shafts. This paper provides an overall description of the PHX Sky Train project, a summary of the ground conditions, design requirements, load test results and construction methods and equipment used to successfully install the drilled shafts for this project.

Jan 1, 2010

By Martin Walker, Joseph Ang, Jongwon Lee, Alvin Bayudanto, Lilian Lorincz, Morteza Khorshidi, Wenyong Rong

This paper presents a case history of liquefaction susceptibility evaluation study for a major infrastructure project in the San José area. The subsurface material of the study area consists of Holocene alluvial deposits composed of interbedded and crosscut clays and silts, sands and gravels. The simplified approach for liquefaction triggering evaluation was carried out using both CPT data and SPT data representing site’s seismic capacity and the peak ground acceleration associated with a return period of 975 years at ground surface representing seismic demands. Site-specific cyclic stress ratio (CSR) profiles as seismic demand are also estimated from one-dimensional site response analysis. The simplified approach uses empirical depth stress reduction factors (rd) based on generic shear wave velocity profiles to account for the non-rigid response of the soil profile in estimating CSR. The CSR profiles of the simplified procedure were examined by completing site response analyses using site-specific soil profiles to represent site-specific seismic demands in the liquefaction triggering evaluation. The paper concludes with a comparison and discussion of the liquefaction evaluation examining results from CPT versus SPT data, and the comparison of CSR profiles from the simplified procedure versus site-specific response analysis.

Sep 8, 2021