Search Documents

By Timothy C. Siegel

In response to a solicitation for ground improvement for the construction of a new hospital in Owensboro, Kentucky, the team of Berkel & Company Contractors and Dan Brown and Associates PC designed and installed lightly reinforced cast-in-place piles (known commercially as Cast-in place Ground improvement Elements or CGEs) as part of a composite ground system. The concept of the design is that the structure load is shared between the piles and the soil subgrade. The load sharing is controlled (to some degree) by the placement of a cushion between the pile head and the bottom of the overlying spread foundation. In an effort to confirm the design principles and to better understand the behavior of composite ground, the design-build team performed plate load tests on ground with a single CGE and with a group of CGEs. The small plate test (on ground with a single CGE) characterized the stiffness of the cushion. The large plate tests showed that the cushion will distribute the applied load to the CGEs and to the soil subgrade between the CGEs. On the basis of the plate tests, it was concluded that the plate stiffness can influence the test results. The use of a concrete layer was effective at supplementing the plate stiffness. The cushion was shown to be an important component of a composite ground system by allowing mobilization of the soil subgrade resistance and avoiding a stress concentration at the tops of the CGEs that would otherwise be present if the spread foundation and piles were rigidly connected. Because the composite ground system engages the resistance of the soil subgrade, the structural demand is reduced and consequently there is a potential for savings when compared to a conventional pile foundation. Several foundations for the new Owensboro hospital are being monitored for vertical movement during construction of the superstructure that will extend through 2011. At the time of this paper (mid 2011) the settlement of the foundations due to only part of the structural load (primarily the structural steel) has been negligible.

Jan 1, 2011

By B. Sivarama Sarma, Biswabikash Rout

"Seepage control has to be achieved with plastic concrete cut-off diaphragm walls in dam structures. Materials selected for construction of cut-off walls must be durable, impermeable and have stiffness comparable to the surrounding soil.Plastic concrete provides a feasible and economical solution for construction of durable and impermeable cut off walls for dam structures. Plastic concrete wall should not be understood as a concrete wall with similar mechanical properties of concrete used in buildings, piles and spillways sections. Though it consists of the same materials as those of conventional concrete it has the major differences in end product due to predominant addition of bentonite slurry in the mix with very high water cement ratio. This makes the hardened concrete with very low compressive strength less than 5MPa and high failure deformations after the peak load.This technical paper examines a case study, the typical specifications on demand for construction and the issues corresponding to misunderstanding of the material as a structural grade concrete material. Conclusions were drawn based on a few project site quality data and trial mix experimental data. The anomalies in specifications on demand for construction of curtain wall in a dam structure were removed with modifications.INTRODUCTIONDiaphragm walls which are constructed in trenches made of plastic concrete basically serve the function of seepage control under confined measures. They should have the ability to sustain and undergo large plastic strains as compared to conventional concrete. The three basic mechanical properties of plastic concrete cut-off walls are to have least permeability, minimum strength to retain its shape and ability to undergo large deformations under confined loading conditions. The constituents of plastic concrete are cement, bentonite, coarse and fine aggregates, chemical additives to improve flow of concrete and sometimes to retard the setting time and water."

Jan 1, 2017

By B. Soundara, A. Suganya, S. Selvakumar

"Expansive soils have a potential for shrinkage or swelling under changing moisture content. Attempts were made to reduce the swelling potential of expansive soils with conventional additives such as lime, cement, etc. and non-conventional additives such as industrial wastes. In this research an attempt is made to study the feasibility of using granulated waste expanded polystyrene (EPS) as an additive to expansive soil to control swelling. To investigate the effect of mixing waste EPS granules with expansive clays, three expansive soils with different plasticity index were manufactured in the laboratory by mixing sand with sodium bentonite of various proportions. A series of standard proctor test, California bearing ratio (CBR) test, one dimensional free swell and swell pressure tests were performed on these soils. Test results show that the inclusion of EPS granules significantly reduces the percent swell and swelling pressure when subjected to one-dimensional free swell conditions. The dry density and CBR values decrease with increase in EPS content and increased plasticity of the soil.INTRODUCTIONExpansive soils cover an area of about 257 Million hectares on the earth’s surface (Dudal et al. 1965). In India, the area covered by expansive soils is nearly 20 percent of the total area (Mohan et al. 1961). Movement is usually in an uneven pattern and of such a magnitude as to cause extensive damage to various structures, especially lightly loaded structures or pavements (Chen 1975). Stabilization is one of the methods of treating the expansive soils to make them fit for civil engineering purposes. The variety of stabilizers may be broadly divided into three groups (Petry et al. 2002): (a) traditional stabilizers (lime, cement etc.), (b) by-product stabilizers (fly ash, quarry dust, phosphor-gypsum, slag etc.) and (c) non-traditional stabilizers (sulfonated oils, potassium compounds, polymer, enzymes, ammonium chlorides etc.). Apart from these, a number of other ground improvement techniques such as sand cushion technique (Satyanarayana 1966); cohesive nonswelling (CNS) layer technique (Katti 1978) were adopted for the stabilization of expansive soils. Expanded polystyrene (EPS) is a polymeric foam normally available in white colour and is a wellknown packaging material. The geotechnical specialists recognize EPS as the most commonly used geofoam material, a type of cellular geosynthetic which has been in consistent use in geotechnical applications since the early 1960s (Horvath 1995). EPS has very low thermal conductivity and nearly 98% of the volume is air (Lye et al. 2002). EPS has many exceptional properties such as being lightweight, thermal insulating, shock-absorbing and having low-water pick-up, etc. EPS find its applications in geotechnical engineering as light weight fills in the form of blocks (Refsdal 1985, Karpurapu et al. 1992, Zou 2001, Ikizler et al. 2008). EPS can be used as compressible inclusion and as a vibration damper (Horvath, 1994&1995). EPS is also used in lightweight concrete owing to its lightweight, excellent heat preservation and sound insulation properties (Ravindrarajah et al. 1994; Miledet al. 2004 and Babu et al. 2005). Waste EPS granules have been used in with horticultural soils to improve a number of soil characteristics like improving drainage, lightening heavy soils and improving water uptake capacity of soils (Scheirs 1998). Furthermore, it was also used as sub-base materials for pavements and railway track beds (Hanna 1978; Duskov1996), construction materials for floating marine structures and fenders in offshore oil platforms (Bagon et al. 1976), sea beds and sea fences; as an energy absorbing material for buried military structures, (Perry et al. 1991)."

Jan 1, 2017

By Wesley Schmutzler

The Deep Mixing Method (DMM) was employed to raise and support the LPV (Lake Pontchartrain and Vicinity) -111 Levee in New Orleans. Even using innovative technologies, the tight schedule to achieve the 100 year elevation by June 1, 2011 was a daunting endeavor. The size and scope of DMM proposed for LPV-111 was on a scale never attempted outside of Japan. Over 1.65 million cubic yards of DMM was installed. LPV-111 is adjacent to the Bayou Sauvage Wildlife Refuge, which is the largest urban National Wildlife refuge in the United States. By utilizing DMM to control settlement and improve stability of the taller levee, side slopes were steepened from the conventional 1V:4H to 1V:2.85H, thus avoiding encroachment into the Bayou Sauvage and reducing the amount of clay needed for the completed levee. The COE utilized Early Contractor Involvement (ECI) for this contract. The ECI process allowed for input from the DMM contractor, TREVIICOS South, in order to optimize equipment resources and material requirements. This paper gives an overview of the extensive DMM requirements for LPV-111 and explains the benefits of the ECI process.

By C. Vipulanandan

With the aging infrastructure, there is a need to maintain and extend the service life of steel structures in general and steel piles in particular. Steel piles support not only vertical loads but also dynamic horizontal loads in onshore and offshore applications. In order to select the appropriate methods to repair corroded steel piles used in onshore and offshore application, corrosion mechanisms were investigated with the rate of corrosion in various environments. The corrosion rate of steel in soil, water and soil-water interface varied from 2 to 500 µm/year. Based on literature review and analyses, the repair methods can be broadly characterized as protective coating, electro-chemical methods, wrapping and encasement and partial replacement of steel. Also, methods to evaluate the repair materials and the repair configuration have been documented.

By Ramon Varghese, A. Boominathan, Subhadeep Banerjee

Pile raft foundation system has been accepted as an economic foundation design for high rises and heavily loaded structures. Seismic response analysis of PR foundation systems involves complex pile-soil-pile interaction as well as raft-soil-pile interactions, for which simplified methods have limitations. Kinematic rocking of a pile group is known to be influenced significantly by the pile configuration. The presence of an embedded pile cap, or a raft, as in the case of a piled raft can further alter the dynamic characteristics of a pile group-soil system. In the present study, frequency dependent kinematic response factors are evaluated for piled raft foundation, using the substructuring approach based ACS SASSI program. Performance of the numerical analysis methodology is first evaluated with results from analytical and experimental studies reported in literature. The effect of pile layout on kinematic response is then studied for a piled raft in clay system based on a centrifuge shaking table test reported in literature. Kinematic response factors and horizontal impedances were determined for varying pile spacing ratios. The influence of raft has been found to increase kinematic translation by up to three times in the piled raft in clay system. Pile configuration is found to play a significant role in kinematic rocking of piled rafts. The presence of raft is observed to significantly reduce dynamic rotational stiffness coefficient in the dimensionless frequency range of 0.23 to 0.6, and increase damping coefficient after a dimensionless frequency of 0.4, for all pile configurations studied. The effect of an embedded raft is hence an important consideration while evaluating foundation input motion as well as impedances of piled raft foundations. INTRODUCTION The Piled raft foundation (PR), is a composite foundation system that facilitates load sharing between pile and raft. It is an economic foundation option for high rises and heavily loaded structures. Soil structure interaction (SSI) in PR system involves raft-soil-pile, and pile-soil-pile interactions which needs to be considered in static or dynamic SSI analysis. The effect of pile can have substantial influence on foundation input motion, for seismic analysis (Di Laora et al. 2017). Piles are observed to depress a wide spectrum of the seismic excitation (Fan et al., 1991, Di Laora & de Sanctis, 2013). Although kinematic response of pile groups have been extensively studied in the past, the influence of the presence of raft on kinematic response characteristics of pile groups has not received much attention.

Jan 1, 2018

By Lisa M. Splitter

Drilled displacement piles were constructed as the foundation for a proposed 10-story building in San Francisco, California. At the study location, the stratigraphy consists of 14 to 21 feet of fill and 13 to 23 feet of weak, compressible clay (?Bay Mud?), underlain by dense sand, stiff clay, and bedrock. A sensitive critical public utility is located within approximately 20 feet of the constructed piles along one side of the building. The utility pipeline is entirely within the Bay Mud where it is adjacent to the project site. The San Francisco Public Utilities Commission (SFPUC) developed limits on the allowable total and differential movement of the utility pipeline. As requested by the SFPUC, inclinometers and piezometers were installed to monitor the soil movement and pore pressure increases in the Bay Mud caused by the installation of drilled displacement piles. Action levels were set such that if displacement and/or pore pressures reached an action level, the installation methodology would be reevaluated and additional measures to reduce these effects would be implemented. This paper will present the sequence of pile installation near the pipeline and monitoring points, and the data collected from inclinometers and piezometers at variable depths and distances from the piles. The data will highlight the build-up and dissipation of pore pressures over time and the displacement of Bay Mud caused by the pile installation. The conclusions of the study are useful in determining sequencing, spacing, predrilling, and other measures that can be implemented to decrease the displacement potential and pore pressure build-up in soft clays.

Jan 1, 2009

By M. Reza Saberi, T. Ted Miyake

Driven piles are a common tool in any engineer’s toolbox for supporting large structures over very soft ground, especially in high seismic risk zones. Challenges include achieving sufficient vertical and lateral load capacities within the constraints of pile spacing and geologic conditions. This was the case for a project in Orange County, California with a state-of-the-art, $180 million plant for biosolids processing, biogas management and energy recovery located in marshland next to an existing waste water treatment plant. The new construction for the Irvine Ranch Water District included a 70-foot (21 m) tall building and three closely spaced, 90-foot (27 m) high, 65-foot (20 m) diameter, egg-shaped steel digester tanks. The lower 35-feet (11 m) of the tanks were constructed below ground level. The site was underlain by up to 45 feet (14 m) of highly compressible peat and organic clays with standard penetration test (SPT) blows as low as 2 blows/ft (30 cm). Some of the peat layers had measured in-situ dry densities of less than 30 pcf (480 kg/m3) with moisture contents of over 250 percent. The soft clays and peat were underlain by a dense layer of sand and gravel at depth. Groundwater was very shallow. While nearby sites were designated by others as seismic site class “D”, this site was clearly class “F” (SF) which required site specific seismic hazard and time history analyses. Six recorded time histories were selected from the 1994 Northridge, 1989 Loma Prieta (California) and 1999 Chi Chi (Taiwan) earthquakes for the ground motion analysis considering the magnitude of the earthquake, distance to the source, characteristics of the earthquake source (i.e. type of fault displacement), peak ground acceleration, local site geology, station type (i.e. free-field or small structure stations), and spectral content that was similar to the period range of interest. Following ASCE’s Guideline Document 7-05, a site-specific horizontal acceleration response spectra (ARS) was developed for the maximum credible earthquake (MCE) associated with the site.

Jan 1, 2018

By Swaminathan Srinivasan, Jess A. Schroeder

"Landslide activity along U.S. 50 in Cincinnati, Ohio (USA) has caused roadway damage for decades. After a necessary closure of three lanes due to slope movements, emergency stabilization measures were undertaken to protect the roadway by providing a short-term solution necessitated by The Ohio Department of Transportation budget constraints. The landslide shear plane occurred on a sloping bedrock surface as much as 50 feet below grade. Drilled shafts were installed 40 feet downslope of the roadway shoulder and were heavily reinforced across the shear plane but steel reinforcing did not extend the full length of the shafts and was stopped well short of the ground surface. Instrumentation data has been collected for 11 years after construction has shown these “Stub Piers” have provided much more than a short-term solution and have provided an attractive alternate to conventional deep shafts or tieback drilled shaft options.INTRODUCTIONLandslide activity has occurred along U.S. Route 50 in western Cincinnati, Ohio for many decades. The site is located between North Bend and Addyston, Ohio on the right descending (cutting) bank of the Ohio River. Road distress caused by slope movements required periodic repairs over recent decades. Railroad tracks downslope of the roadway also showed signs of horizontal displacement and periodic repair. Visual evidence in 2005 suggested the shear plane extended below the US 50 roadway and extended out into the Ohio River.A weed and brush-covered slope extended down slope from the roadway at about 3H:1V for a vertical distance of about 20 feet. Above US 50, the hillside continued to rise more than 100 feet. There is a railroad right-of-way at the toe of the slope with the Ohio River bank just downslope of the railroad.In 2005, Terracon Consultants was retained by the Ohio Department of Transportation (ODOT) to perform a geotechnical study that included 17 test borings and inclinometer monitoring at 4 locations. Roadway damage was occurring (see Figure 1). After only a few weeks of monitoring, the inclinometer casings sheared off about 50 feet below grade, near the soil / bedrock interface (see Figure 2). Soon after, the roadway distress worsened, causing ODOT to close 3 of the 4 lanes to traffic and reroute traffic onto the remaining single lane and shoulder. Terracon was asked to develop a stabilization design under emergency repair conditions. However, both limited budget and time-related constraints necessitated a direction by ODOT that the solution be at least “pseudo” short-term (3 to 5 years)."

Jan 1, 2017

By Han Jie

The results of full scale plate load tests on stone columns on soft clay in coastal areas are presented in this paper. Four load tests were made, two of which were performed on the ground treated with stone columns, one on an isolated stone column and the last one on the untreated ground. For a given stress range, the settlement of the rigid plate, the stress concentration factor, and the excess pore water pressure were measured. It is found that the distribution of vertical stress beneath the rigid plate supported by the composite ground of stone columns is very different in shape from the one by the untreated ground, that the stress concentration factor has a relation with the stress level and time, that the stone columns increase the bearing capacity up to by 2 times, and that the ground stabilized by stone columns is of great advantage to keep the foundation stable.

Jan 1, 1991

By Jogeshwar P. Singh, Ahmed AlaaEldin, Mohamed Ashour

The presented methodology allows the determination of the response of laterally loaded battered long piles in sandy soils based on the soil-pile interaction. The Strain Wedge (SW) model which was originally developed for laterally loaded vertical piles is modified to assess the behavior of laterally loaded battered piles with the consideration of soil and pile properties. The method predicts the pile-head response and associated p-y curves. The presented soil-pile model accounts for the variation of the direction and magnitude of the batter angles from the vertical position. Unlike current practice, the proposed technique also provides the p-y curves for battered piles in sandy soils based on soil and pile properties (i.e., sand relative density, friction angle, pile geometry, etc.). The proposed methodology has been validated through a number of comparisons with full/model-scale pile load tests. INTRODUCTION The influence of pile battering on the lateral response of piles is rarely studied in the literature. Over the last decades and as suggested by Kubo (1962) and Zhang et al. (1999), a p-y multiplier is applied to predict the response of laterally loaded battered piles from an equivalent vertical one. Several researchers conducted model-scale piles load tests to understand the behavior of battered piles subjected to lateral load (Juvekar and Pise 2008; Meyerhof and Ranjan 1973; Meyerhof and Yalcin 1994). However, such tests were conducted on model piles with diameters less than 30 mm which may not have reflected actual soil-pile interaction. Battered piles are generally categorized as positive or negative battered piles according to the angle of pile installation as shown in Fig. 1. From the small-scaled and numerical models of battered piles, it was found that the lateral capacity of negative battered piles is larger than that of vertical ones. On the other hand, the positive battered piles have lower lateral capacity when compared to vertical piles (Fan-ren and Ji-Ming 2011; Juvekar and Pise 2008; Manoppo 2010; Reese et al. 2004; and Reese and Van Impe 2011).

Jan 1, 2018

By Arash Khosravifar

The seismic design of extended pile shafts for the combined effects of dynamic shaking and liquefaction-induced lateral spreading is investigated using nonlinear dynamic finite element analyses (NDA). Results of NDA parameter studies are used to illustrate how inertia and lateral spreading loads combine during shaking. The NDA results are used to evaluate equivalent static analysis (ESA) methods. Implications for design practice are discussed.

Jan 1, 2010

By C. Vipulanandan, M. Dawood, Dongmei Pan

"With the aging infrastructure, there is a need to maintain and extend the service life of steel structures in general and steel piles in particular. Steel piles support not only vertical loads but also dynamic horizontal loads in onshore and offshore applications. In order to select the appropriate methods to repair corroded steel piles used in onshore and offshore application, corrosion mechanisms were investigated with the rate of corrosion in various environments. The corrosion rate of steel in soil, water and soil-water interface varied from 2 to 500 µm/year. Based on literature review and analyses, the repair methods can be broadly characterized as protective coating, electro-chemical methods, wrapping and encasement and partial replacement of steel. Also, methods to evaluate the repair materials and the repair configuration have been documented.IntroductionOne of the biggest challenges facing the aging infrastructure is the materials loss and deterioration due to corrosion. Many studies indicate that in the US alone, costs due to corrosion loss is more than $276 billion annually (Michiel et al., 2010). Corrosion is the major cause of deterioration of steel structures and components (MNC, 2005). Load bearing steel piles are used as foundations for various types of structures and hence corrosion is very much influenced by the environment such as soil, water and soil-water interface. Corrosion of steel pile foundations may result in reduced capacity in the axial and lateral directions. Hence, understanding the rate of pile corrosion is essential to select the appropriate repair methods to avoid excessive deflection and failure (Decker et al. 2008).To prevent the deterioration mechanisms that attack a pile, it is fundamental both to identify and understand the deterioration mechanism that has been the cause of damage. Understanding the deterioration mechanism allows the engineer to design a repair that will combat this type of damage. It is widely recognized that the corrosion of carbon steel in soil, water and soil-water interface proceeds according to the following simplified anodic reaction and cathodic reactions in the presence of oxygen (Decker et al. 2008)."

Jan 1, 2017

By Dhanaji S. Chavan, Thallak G. Sitharam

"It is well known that sites comprising of saturated loose sand undergoes large deformations, due to liquefaction, during seismic shaking. To cope with this, different mitigation techniques such as vibroflotation, deep dynamic compaction, compaction grouting, deep soil mixing etc. have been used in practice. However, as all these methods are costly, a new mitigation technique is required. Air injection has emerged as a new mitigation technique in which air is injected into the saturated loose sand. The introduced air makes the pore fluid mixture compressible and results into decrease in the generation of excess pore water pressure during seismic shaking. This paper reviews the laboratory and field studies performed to investigate the effect of air injection on liquefaction resistance. In addition to this, previous research in the direction of desaturation has evolved different techniques to generate gas in saturated sand. These techniques have also been discussed in the present paper. All the field and laboratory studies have shown that even a slight decrease in the degree of saturation increases the liquefaction resistance significantly.Keywords: desaturation, air injection, liquefaction resistance, pore pressureINTRODUCTIONEarthquake events in the past, caused liquefaction of loose saturated sands at many sites in the world. The consequence of liquefaction varied from small deformations to catastrophic failures such as flow slides, lateral spreading, sand boiling etc. (Kramer, 1996). To reduce the liquefaction potential of such soils, different mitigation techniques have emerged across the world. Some of the most widely used mitigation techniques are vibroflotation, deep dynamic compaction, compaction grouting and deep soil mixing (Idriss and Boulanger, 2008).Yoshimi et al. (1989) found that the liquefaction resistance of partially saturated sand is significantly higher than that of saturated loose sand. Further, Pietruszczak et al. (2003) proposed desaturation of the saturated loose sand as a new liquefaction mitigation technique. It is observed that the liquefaction resistance of sandy soil is enhanced significantly owing to the desaturation caused during construction of sand compaction piles (Ishihara et al. 2003). Over past few years research is being carried out on desaturation of sandy soil and its liquefaction resistance ( Ishihara et al. 2003; Okamura and Soga 2006; Yegian et al. 2006; Yegian et al. 2007; Takemura et al. 2009; Eseller-bayat et al. 2013; He et al. 2013; Marasini and Okamura 2015; Zeybek and Madabhushi 2016). As a result of this, different techniques of desaturation have also emerged. Different studies conducted in this direction and their outcome has been discussed in the section to follow."

Jan 1, 2017

By Mandy Korff

Walls consisting of CFA-piles are often used for vertical cut offs for building pits. Several methods of installation and geometry may be used and sizes, depths and strengths of walls necessary vary widely. Based on experience with secant CFA-pile walls in The Netherlands, requirements for this type of wall can be set with a risk management view to it. This paper describes those requirements, based on specific local conditions.

Jan 1, 2006

By Gustavo E. Armijo

This job was done in Morristown, NJ, with mono fluid system jet grouting for the construction of a new bank building. After the demolition of the existing two story structures, an excavation in loose sandy fill materials was necessary in order to reach the new structure basement level. Due to this jet grouting was selected as a medium to provide both excavation support and permanent underpinning, minimizing the adjacent building settlements. These two adjacent buildings were partially underpinned with a "gravity wall" made with 2 and 3 rows of secant vertical and inclined jet grout columns. Besides the classical jet grouting control methods, during the jet grouting execution, all the drilling and grouting parameters were recorded by a proprietary system called "Slogger". Additionally, after the jet grouting execution, an innovative result control technique was used by means of the application of the same parameter recording system. Some of the production columns were re-drilled and a comparison was made between the obtained drilling parameters and those obtained for the same age test columns. Under the referred existing conditions and in comparison with the conventional underpinning techniques, this project demonstrated that jet grouting, with proper execution and result control, can be faster than them and can maintain the building structural stability and act, at the same time, as a retention system minimizing the existing building settlements.

Jan 1, 2002

By António A. Henriques, António Gomes Correia, Ana Teixeira

"Abstract Pile foundations are often used for important structures, and thus, reliability evaluation is an important aspect of the design. Reliability methods have become increasingly important as decision support tools in different areas. The main benefit of reliability analysis is that it provides quantitative information about the parameters (uncertainties) that most significantly influence the behaviour under study. In particular, the design of pile foundations still involves many limitations and uncertainties, particularly when there is not enough investment in soil characterisation and/or pile load tests. In addition to the uncertainties associated with soil characterisation, physical, statistical, spatial and human uncertainties exist. In this subject, the primary purpose of this paper is to demonstrate the application of reliability methods to geotechnical pile design (axial load). It also presents a simple and practical approach to performing it using Monte Carlo Simulations, intending to provide knowledge for code harmonisation and encouraging the development of such methodologies in geotechnical practice. Sensitivity analyses are shown to understand the influence of each uncertainty type coming from different sources. An application example indicates, corroborating other studies, that the model error is the most influent uncertainty. As such, when using the different models (SPT-, CPT- and PMT-based) for bearing capacity, the results emphasise the need for a well-defined and wellcharacterised resistance model, also these results allow the engineer to understand how important the load tests can be to achieve reliable results and economic designs.1 IntroductionUnlike the approach to reliability evaluation used in structural engineering, the traditional procedure used in geotechnical designs addresses uncertainties through high global or partial safety factors (SF), mostly based on past experience. However, this approach to addressing uncertainties does not provide a rational basis for understanding their influence on design.Furthermore, the new regulation codes and social concerns, such as the sustainability or the economy, are imposing geotechnical engineers to increase their ability to deal with uncertainty in a direct and more rational way. Designs should be economic, sustainable and reliable at the same time. Concerning the reliability part of design, different approaches can be done, but the most important thing to keep in mind is the simplicity and efficiency of the tools and applied methods."

Jan 1, 2014

By Paul M. Wiltcher

This paper discusses how benefits in engineering design can be achieved from combining existing GRP concrete design guidelines with carbon steel design codes primarily made possible due to the increase in the constitutive properties of modern composite rebar or GRP. It also examines the technical and practical considerations necessary to both construct and ensure the integrity of composite rebar during transportation and handling on site and the measures taken by Franki-Cementation Joint Venture to ensure the safe deployment of the GRP in the workplace on the Noord/Zuidlijn Project in Amsterdam between 2003 and 2006.

Jan 1, 2006

By Elizabeth Varghese, Sanket Rawat, Prachuryya Kaushik, Ravi Kant Mittal

"Geo5 Software is gaining popularity worldwide due to its expediency in analysis and design of pile foundation. The analysis is based on various theoretical, empirical and semi-empirical methods available in existing literature and various country standards. Moreover, the ultimate resistance of pile in the software is based CSN 73 1002, Fellenius method, NAVFAC DM 7.2 and Tomlinson method. Due to the specificity in calculation of ultimate resistance, it becomes necessary to validate the results arrived using the software for better accuracy. Furthermore, the above-mentioned methods are not necessarily popular in every design offices. Therefore, an attempt has been made to predict the efficiency of Geo5-v15 software to analyze the pile foundation by comparing it with the results obtained using the analysis based on Indian Standard IS 2911:2010, performed with spreadsheet specifically designed for the same purpose. The accompanying outcome of the comparison and several shortcomings found in the design part associated with the software has been highlighted in the later part of the paper. Besides, the optimization tool present in the software is also described for the more efficient and economic design of pile foundation, hence contributing as practical aid to structural engineers.INTRODUCTIONThe analysis of individual pile foundation and pile in groups can be said to include the three main important parameters – Ultimate bearing capacity, Settlement and Structural Design. The first two parameters are to be evaluated to check the reliability of foundation against ultimate limit state and serviceability limit state. The third parameter includes the analysis of pile against both horizontal and vertical load. This parameter mainly intends to evaluate the size of foundation and the amount of reinforcement. Geo5 is a software which can expediently compute the above mentioned three parameters just by the mere input of the necessary factors. The ultimate bearing capacity analysis in Geo5 is based on various theoretical, empirical and semi-empirical methods available in existing literature and various country standards depending upon the drained and undrained condition of soil (Bowles, 1968; CSN 73 1002,1987; Felenius,1991; NAVFAC DM 7.2,1984; Tomlinson,1977). However, the method mentioned in IS 2911 (2010) is not the same and have slight variations in way of evaluating the parameters which affect ultimate bearing capacity. Therefore, it becomes necessary to evaluate the efficiency of Geo5 with respect to the value of ultimate bearing capacity and therefore, asserting the confidence in the software based method for the convenience of the designs in Indian Scenario. The present study aims to evaluate the efficiency of Geo5 v-15 software in predicting the ultimate bearing capacity of pile foundation. The results of the software are compared with the bearing capacity calculated using IS 2911 (2010) with the help of excel sheet. Moreover, as the software is frequently put under revision, therefore a comparison of this version has also been made with the latest version of Geo5 (2017) to check whether the latest revision has accounted for the discovered shortcomings. The design steps performed in the software is also shown. As Geo5 make use of IS 456 (2000) for the design purpose, hence it can be considered as reliable with respect to the estimate of the third parameter. Furthermore, the optimization process is also shown in the later part of the paper to emphasize the simplicity of the software in economizing the design cost."

Jan 1, 2017

By Mark DeSalvatore

Currently, at Caltrans, the Office of Structure Design is carrying out an extensive seismic retrofit program involving transportation structures throughout California. The goal of the retrofit program has been to upgrade existing transportation structures to meet the present seismic codes and anticipated loads that are generated during a seismic event Part of the retrofit program involves retrofitting existing structure foundations when required. To determine if the foundations of a specific structure need to be retrofitted, an engineering analysis of the existing foundations has to be done. If the engineering analysis of the structure foundations determines that the foundations will not meet the load carrying demands required by the structural engineer, the existing foundations are then retrofitted. The retrofit projects that require foundation modifications can be separated into two general cases. The first case comprises structures where the original designs will not meet the demands of the present seismic design code. In this case, the existing foundations are not capable of providing the load capacities the current seismic code requires. The second case consists of structures where the retrofitting of the superstructure will increase the required load carrying capacity of the existing foundations during a seismic event In this case, the anticipated load demands on the existing foundations are greater than the foundations are capable of providing. For either of the cases listed above, the present strategy for increasing the capacity of the existing structure foundation consists of installing tiedown anchors or large capacity piles to provide the required resistance to seisraically induced loads.

Jan 1, 1993