Search Documents

By Jamie D. McEwan

To cater for the future introduction of 12 car trains, London Blackfriars railway station is being extended from the north end to span across the River Thames. Following the demolition of existing buildings, a number of challenges had to be overcome including working adjacent to a live railway line, above live London Underground tracks and working in small restricted spaces. Trains entering and exiting two lines of track at the bridge's north end of track meant that access was difficult due to the location and proximity to existing infrastructure. The site was very much constrained and congested and there were also a series of works in place to maintain passenger flows so as not to inconvenience the travelling public. The site had been developed many times in the past resulting in a number of obstructions that would require removal during the piling work including old brickwork, reinforced concrete, redundant railway sleepers and track and existing concrete and timber piles. A number of solutions had to be devised to overcome these obstructions. Piling works were undertaken during the day and at night to meet programme.

Jan 1, 2011

By Larsson Lars-Erik, Rani Isa, Martin Jönsson, Håkan Bredenberg, Mats Larsson

"IntroductionSteel Core Piles are used extensively in Scandinavian countries, where hard rock is found within reasonable depths. A steel core is cast into a drilled steel tube casing and a rock hole is extended below the casing. This pile type is considered a very reliable type of pile, and for urban environment it has several advantages compared to other types of piles. One critical phase of the installation is the drilling of the casing. Usually a DTH (Down The Hole) hammer is used. Drilling in fine grained soils, e g silt, below the ground water level, may give rise to an excessive volume of soil material flushed up from the point of the casing, resulting in unacceptable settlements around the pile installation area.Using a new method for drilling of the casings, the ELEMEX-method has proven to significantly reduce the risk for such problems. In the paper a case record from a ground improvement project in central Stockholm is described. Ground settlements around the drilling area were carefully monitored over a longer period. Both the new drilling method and the conventional DTH casing drilling method where used, so that the corresponding ground settlements could be compared. Settlement records and comments are included in the paper.The paper also gives a description of the project. The installation of new piles and foundation constructions cover a whole city block in Stockholm downtown. The reason for the replacement of the old, damaged wooden piles were due to their destruction caused by a long time lowering of the ground water table. The paper gives a description of the new drilling method as well as an overview of usual urban foundation issues and their solution in Sweden, Finland and Norway.Drilled Foundation MethodDrilled Foundation, using drilling methods originally developed for drilling of large diameter rock holes, is today a standard method for the installation of piles, tiebacks, drilled pile walls and other foundation components, especially in urban built up areas where other techniques as drop hammers, augers, vibratory hammers and other equipment fail to meet the requirement, se ref(1). Drilled foundation is for example used for"

Jan 1, 2014

By L. F. Miao

Studies were carried out to investigate the ultimate soil pressure acting on pile(s) undergoing lateral soil movement in soft clay. A special apparatus has been designed to apply a uniform rectangular profile of lateral soil movement on the rigid pile(s) with pinned head and tip conditions to obtain the ultimate soil pressure. The piles were 16 mm (5/8 in) in diameter. For the pile group tests, the behavior of different number of piles (2, 3, 4, 6 and 9), pile arrangements and center-to-center spacings (3 and 6 diameters) were investigated. In this paper, the group factors of 11 combinations of number of piles, pile arrangements and pile spacings are presented. The group factors are given for individual piles in a pile group as well as for the entire group. Generally, the group factors of individual piles in a group varied significantly according to pile spacing in both directions, and pile arrangement; the group factor of the whole group reduced with an increasing number of piles, and increased with increasing pile spacing. For a pile group with the same number of piles but different pile arrangement, no significant difference was found in the group factors for the entire group.

Jan 1, 2008

By Osamu Taki

This paper presents the system, the strength of column, the design concept, and the applications with four case histories from the past project as the general aspect of Geo-Column (trade mark of single soil-cement column by SCC Technology, Inc.). In the system, it shows the installation process and drilling/mixing tool with the mixing process. In the design concept, it shows how to design Geo-Column against the vertical and horizontal load. Finally, it shows the applications with four case histories, (1) building mat foundation, (2) isolated foundation on the pedestrian bridge, (3) bridge spread footing and slope erosion control wall in the channel, and (4) cut-off wall and shoring wall in the underpass roadway to the railroad.

Jan 1, 2000

By Matthew E. Meyer

The intent of this manual is to provide guidelines for observing and documenting the installation of ACIP piles. The manual may also serve as a guide for the training of inspection personnel. It is expected that the general guidelines and procedures described in this manual for the inspection and installation of ACIP piles will be supplemented by engineering judgment, local practice, and experience. ACIP pile construction procedures will vary depending on soil, rock, and groundwater conditions. This manual represents a wide range of possible applications in a variety of projects. It is not intended to be applicable in all situations nor replace engineering judgment for any given project. Therefore, an all-inclusive inspection manual is not considered practical or desirable. This manual should not be used to interpret or replace project specifications. It has, however, been prepared to complement the Augered Castin- Place (ACIP) Piles Manual model specification (DFI, 2003).

Jan 1, 2010

By Dennis J. Riley

A. This outline addresses what a sub-contractor, or a subsub-contractor should do to get paid in the event the general contractor or building owner files for bankruptcy. B. Negotiating payment terms. Progress payments vs. "pay when paid". How a sub or subsub can avoid financing the contract. C. Court interpretation of "pay when paid" clauses allow postponement not excusal of payment. See, e.g., Seal Tite Corporation v. Ehret. Inc., 589 F. Supp. 701 (D.N.J. 1984) (where the court held that the general contractor could not delay payment indefinitely to the subcontractor in the event of non-payment from the owner); United Plate Glass Co. v. Metal Industries. Inc., 525 A.2d 468 (Commw. Ct. Pa. 1987) (where the court held that payment from owner was not a condition precedent to paying subcontractor but instead a timing mechanism indicating when payment should be made); But see. Straham v. Landis Construction Co., 499 So. 2d 417 (La. App. 4 Cir. 1986) (where the court strictly interpreted the "pay when paid" clause).

Jan 1, 1991

By Frank Rausche

Without doubt, driven piles are the most economical deep foundation element for a nearshore environment, providing for high bearing capacities and stiffness, quick installation times, assured quality by simple monitoring and inexpensive dynamic load testing during restrike testing. However, when the pile top elevation is several meters below water surface, questions often arise as to the most reliable and economical pile installation method. Frequently encountered, yet relatively expensive, solutions include driving inside a dewatered cofferdam, driving long piles that are later cut off below water surface, or using an underwater hammer. Arguably, the most economical solution is driving the piles with a follower or chaser. However, many foundation engineers shy away from this solution because of the uncertainty associated with the transfer of energy through the interface between follower and pile, the associated potential driveability problems and maybe the limited fatigue life of the follower. This paper will demonstrate how the driveability of a hammer-follower-pile-soil system should be analyzed prior to installation and how to model the pile-follower interface both for steel and concrete piles. As an example, results will be presented which were obtained for both steel pipe piles and precast concrete piles, driven by a single-acting diesel hammer through a steel follower for a pre-construction test pile program in Venice, Italy. While analysis of the steel pile-follower system was straightforward, for the concrete piles, the presence of a soft cushion material whose material properties changed continuously posed some difficulty. Pile Driving Analyzer® measurements and CAPWAP® analysis yielded not only realistic stresses and transferred energy values in the pile, but also reasonable model parameters for further use in a pure wave equation analysis. As a side note for clarity, the dynamic measurements and analysis results herein presented are based on the GRLWEAP and CAPWAP software. GRLWEAP is commonly used all around the world for the preparation of pile driving jobs. The program either yields a bearing graph that relates bearing capacity and pile stresses to blow count or set per blow or it predicts blow counts and pile stresses as a function of pile penetration. These results allow the contractor to estimate driving time and select an economical hammer and driving system for a safe and efficient installation. CAPWAP on the other hand is the analysis of choice once a pile has been installed and records of pile top force and velocity have been acquired during installation or during a restrike test. CAPWAP is a signal matching program which calculates for one particular impact (for example at the end of driving) the static and dynamic soil parameters. Its final results include the calculated resistance distribution, the complete stress history in the pile and also a simulated load set curve. The CAPWAP calculated dynamic soil parameters can also be used in a Refined GRLWEAP analysis to generate a calibrated bearing graph."

Jan 1, 2006

This manual is limited to Augered Cast-in-Place (ACIP) piles constructed using a hollow stem continuous flight auger. 1.1SCOPE AND LIMITATIONS The intent of this manual is to provide guidelines for observing and documenting the installation of ACIP piles. The manual may also serve as a guide for the training of inspection personnel. It is expected that the general guidelines and procedures described in this manual for the inspection and installation of ACIP piles will be supplemented by engineering judgment, local practice, and experience. ACIP pile construction procedures will vary depending on soil, rock, and groundwater conditions. This manual represents a wide range of possible applications in a variety of projects. It is not intended to be applicable in all situations nor replace engineering judgment for any given project. Therefore, an all-inclusive inspection manual is not considered practical or desirable. This manual should not be used to interpret or replace project specifications. It has, however, been prepared to complement the Augered Cast-in-Place (ACIP) Piles Manual model specification (DFI, 2003).

Jan 1, 2010

By M. Hesham El Naggar, Yasser Abdelghany

"ABSTRACT: The axial and lateral monotonic and cyclic behavior of helical pile foundations was investigated and new innovative helical screw systems suitable for seismic loadings were developed and patented. More than one hundred full scale field load tests were conducted on instrumented helical screw piles installed in cohesive soil. The piles included: plain helical screw piles (P-HSP); grouted (G-HSPs); fiber reinforced polymer FRP-G-HSPs; and reinforced grouted RG-HSPs. The RG-HSP piles axial capacity was more than twice that for P-HSP, with minimal reduction after cyclic loading, and their lateral capacity was more than 3 times the P-HSPs capacity. A 3-D finite element model was established. The results of 3-D finite element modeling were used to establish the load transfer mechanism and a design methodology for the considered piles.INTRODUCTION AND LITERATURE REVIEWHelical (screw) anchors have been utilized in tension loading and have gained popularity for bearing load applications. Helical piles represent an overall cost effective alternative to conventional piles for new construction and repair applications. The helical piles speed and ease of installation, less noise during installation added advantage with regards to their efficiency and reliability for underpinning including re-support and reconstruction of distressed and damaged foundations for either stabilization or rehabilitation. The “square shaft” SS175 pile is a segmented deep foundation system with helical steel bearing plates (helices) welded to a central steel shaft. Load is transferred from the shaft to the surrounding soil through these bearing plates. Segments or sections are joined with bolted couplings. Practically installed depth is limited only by soil resistance and economics. A helical bearing plate or helix is one pitch of a screw thread. All helices regardless of their diameter have a standard 75 mm pitch (Figure.1). The performance of single helical anchors and group action were studied experimentally and theoretically by several researchers, the researches focuses on the installation torque and uplift resistance. Some researches focus on the load carrying capacity with little pile response to cyclic loading effects or to instrumented full scale field testing. Helical piles axial compressive or lateral loading still is not well characterized and needs more analyses and their seismic performance was not investigated. For such this research was initiated to investigate the helical piles monotonic and cyclic performances under axial and lateral loadings to consider their usage in different applications in seismic zones. Among the several researchers, Clemence (1983); Mooney et al. (1985) conducted field and laboratory testing; Hoyt (1989), Hoyt et al. (1995), and Ghaly and Clemence (1998) conducted theoretical and experimental testing, Puri and Vijay (1984), Huang et al. (1995), Perko (2000), and Pack (2000) conducted theoretical analyses. Rao and Prasad (1993), Prasad and Rao (1994), conducted experimental testing; Vickars and Clemence (2000) studied the performance of helical piles with grouted shafts."

Jan 1, 2014

By Shinji Sassa, Naoki Takahashi, Eiji Kohama, Wakaki Tsuda, Hidenori Takahashi, Ikuo Towhata, Yoshiyuki Morikawa

"Abstract Deep mixing method has been employed increasingly in recent years as a countermeasure against subsoil liquefaction. Column-type solidification, however, has been thought to have little effect as a liquefaction countermeasure, because the shear deformation of unimproved soil between the columns cannot be reduced. In recent years, experimental results have been reported that imply that solidified columns can reduce the shear deformation of unimproved soil around them. A new arrangement has been proposed to mitigate lateral flow induced by liquefaction. In this study, a series of dynamic centrifuge model tests was conducted to verify the lateral flow resistance of stabilized columns. The results indicate that stabilized columns can reduce the lateral flow of liquefied ground if the column displacement and the column head rotation are restricted. This paper concludes that it is important to restrict the displacement and the rotation of the column head by surface improvement to mitigate the lateral flow of liquefied ground.INTRODUCTIONDeep mixing method has been employed increasingly in recent years as a countermeasure against subsoil liquefaction. The solidified body formed by the deep mixing method is usually block or lattice shape, composed of solidified columns that overlap each other horizontally. Lattice-type solidification has been shown to be effective as a liquefaction countermeasure despite the presence of unimproved soil inside the lattice wall, because the shear deformation of the interior soil is restrained by the wall (Suzuki et al., 1989). On the other hand, it has been thought that column-type solidification cannot reduce shear deformation of unimproved soil around columns, because the displacement of a solidified column is less restricted than that of a lattice wall. Column-type solidification has been reported to have little effect as a liquefaction countermeasure, but to be superior in terms of construction cost and applicability around existing underground structures (Koga et al., 1986). However, there are experimental results implying that solidified columns have reduced the shear deformation of unimproved soil and mitigated its liquefaction (Yasuda et al., 2003; Tanaka et al., 2003). Yamamoto et al. (2006) conducted dynamic analyses of ground improved with lattice- and column-type solidification. Their results showed that column-type solidification with an improvement ratio of more than 35% reduces excess pore water pressure generated by earthquakes. Furthermore, the new column arrangement shown in Figure 1(a) has been proposed to mitigate lateral flow induced by liquefaction. It was developed and has been verified using dynamic model testing in a 1 g field (Takahashi et al., 2010a; 2010b; 2013; Towhata et al., 2010). The stabilized columns in this configuration interrupt lateral flow in any direction, unlike those placed in square and triangular arrangements."

Jan 1, 2014

By Ramdane Bahar

"Abstract The design foundations can be performed using Menard pressuremeter rules that require a limit pressure and a pressuremeter modulus. In recent years, another trend of interpretation of this test is appeared. It consists of identifying the rheological soil parameters using analytical or numerical methods and then used to evaluate the bearing capacity and settlement of soil foundations using numerical software. This paper deals with the bearing capacity and settlement predictions of bored piles using two approaches. The first one is the method called ""Pressident"" which is a numerical program developed to analyse pressuremeter tests taking into account the Duncan and Chang model. The second approach is the method developed by Bahar and Olivari based on the generalised elastoplastic Prager’s model with the Von Mises criterion which is suitable to describe the behaviour of saturated clays under undrained conditions. The pressuremeter data, collected on various research and consulting projects are used to explore the relationship between limit pressure and undrained shear strength obtained by the two methods. Numerical calculations, by FLAC2D software taking into account the rheological parameters derived from these two methods, are performed in order to predict the behaviour of a single bored pile subjected to an axial vertical load. The predictions are comparedto the measured data.IntroductionThe Menard Pressuremeter test has been used extensively to measure in situ soil properties and for the design deep foundations in Algeria. These tests are an useful and economical way for obtaining reliable in situ properties of soils and provide the measurement of in situ stress-strain response of soils. From this test, the design foundations can be performed using pressuremeter rules that require a limit pressure, pl, and a pressuremeter modulus, EM. These two parameters are derived from the pressuremeter curve or deduced from existing correlations with undrained cohesion and internal angle friction (Ménard, 1957; Amar and Jézéquel, 1972), and are used to evaluate the bearing capacity of soil foundations and the expected settlements. But, they can also help to identify usual soil parameters required by simple constitutive models for soils in numerical calculations."

Jan 1, 2014

By Neil T. Russo, Peter M. Kandaris, Jogi S. Gadok

"Assessment of subsurface data for foundation design in support of long high voltage electric transmission lines is best accomplished using a probabilistic strategy since only a small portion of structure locations are typically sampled. Probabilistic approaches provide a tool to evaluate site uncertainty in a systematic and rational manner. This paper provides a case history of a risk-based design approach for a recently completed 191-mile long 69/161/345kV steel monopole transmission line traversing Central Iowa. The project owner made available limited subsurface information at project initiation, requiring the design team to obtain additional data within a constrained budget for 1067 large diameter, laterally-loaded deep drilled shaft reinforced concrete piers. The team commissioned a geologic desktop study to reduce uncertainty in subsurface evaluations and aid in selecting additional sample sites. In total, investigation programs tested approximately 15 percent of structure sites. The paper details the probabilistic approach used to estimate foundation geotechnical design parameters, with information from the various studies categorizing strata both laterally and with depth. Low-bound parameters were estimated via a statistical approach at a predetermined reliability level. Significant savings resulted from this approach when compared to conservative deterministic processes. Project QA/QC logged subsurface soil conditions during foundation excavation, then compared as-found conditions to the conditions assumed for design. The team redesigned foundations if either a non-conservative variance in soil conditions was observed or if bedrock elevation differed significantly from design assumptions. As a result, only 22 out of 1067 foundations required modification during construction (2% variance from initial design) with negligible impact on the construction budget and schedule.INTRODUCTIONFoundation design for long high voltage transmission lines presents a unique challenge in that the assessment of subsurface conditions typically requires substantial data that may or may not be obtainable. Investigations are usually performed well in advance of construction, often with limited access to structure sites and typically in remote areas. Probability and risk-based investigation and design strategies offer an opportunity to systematically estimate subsurface profiles and geotechnical design properties with limited data. Risk can be further reduced with dedicated field inspection of foundation construction along with good field and design team communication during construction. This paper presents a case history of probabilistic methods used for the investigation and design of electric transmission line foundations."

Jan 1, 2017

By Kenneth A. Pidgeon

This paper presents a case history on mitigating vibration problems associated with the installation of steel sheetpiles. The project in-cludes installation of steel sheetpiles for a utility trench within 40 feet (12.2 meters) of a very sensitive manufacturing facility. Numerous production line quality control instruments and manufacturing processes within the manufacturing facility are extremely sensitive to vibrations. To minimize the impact to the owner, we specified that the contractor perform a vibration study using different types of pile hammers. The results and conclusions of the vibration study are presented in this paper.

Jan 1, 1995

By H. Mori

The session chairman, Dr. H. Mori, welcomed the delegates to Discussion Session 8. AUTHORS PRESENTATIONS 1 . G. Price, Building Research Establishment. UK Mr. Price expanded on the content of his paper and presented elements of various case histories of bored piles instrumented by the Building Research Establishment. In particular, the interpretation of data from instrumented piles is critically related to: (i) the construction process (ii) concrete stiffness and variability (iii) the effects on the pile due to installing instruments The main role of the instrumentation in the examples presented was to establish pile performance under service loading conditions. Of particular interest is the mobilisation of skin friction and soil shear modulus.

Jan 1, 1991

By Richard F. Sliwoski

The Virginia State Capitol was designed by Thomas Jefferson and constructed in 1785. The Capitol is of great historic and architectural significance to not only the Commonwealth of Virginia but to the nation. It is the oldest operating Capitol in the U.S. and required a total restoration/renovation as well as an expansion to continue to remain functional. Site conditions dictated that the expansion (a new visitor center) be placed underground on the south side of the Capitol building, requiring a 40-foot deep excavation approximately 5 feet from the Building. Because of its historic significance, every measure had to be taken to ensure the safety and function of the Capitol during construction. The construction techniques that were used to make the deep excavation and protect the historic Capitol included a tied back concrete slurry wall, jet grouting, compensation grouting, and instrumentation monitoring. This paper describes the history of the Capitol building, the techniques that were employed for construction of the deep excavation, results of the latest movement monitoring, and factors contributing to meeting the restrictive movement goals.

Jan 1, 2006

Port Gaspé is located on the back side of Gaspé bay and is protected by a natural sand barrier with a length of 2,5 km, from which it got its name, Gaspé Sandy Beach (1). Since 1904 the Gaspé region had a deep water wharf, initially very different, in fact, from the one existing just before the recent reconstruction (2). This wharf with a length of 228 m and a width of 23 m was build of timber cribs. The outside walls of these cribs had been doubled with a wooden wall, creosote impregnated to provide resistance to decay and to the attack of marine organisms (limnorias) (3). Fifteen years ago the upper part of the wood construction had to be removed, because of progressing rottenness and was replaced by an L-shaped reinforced concrete structure (4).

Jan 1, 1987

By Brian R. Zuckerman

The Capitol Area East End Complex is currently being constructed under contract with the State of California Department of General Services on two sites adjacent to the grounds of the California State Capitol Building in downtown Sacramento. The complex will consolidate the headquarters of the Departments of Health Services and Education, which currently occupy several facilities located throughout Sacramento. When completed in 2003, the complex will be the largest civic office project in California history, with approximately 1.5 million square feet of office space and housing nearly 6,300 state workers. The total project is being constructed on five separate blocks in downtown Sacramento, Blocks 171 through 174 and 225. Separate design/build contracts were executed for the construction on Blocks 171 through 174 and the construction on Block 225. The scope of this paper is limited to construction on Blocks 171 through 174, which comprise a square, two blocks on a side, bounded by 15th, 17th, L, and N streets, located immediately to the east of Capitol Park and the State Capitol Building, as pictured in the image shown below.

Jan 1, 2002

By Markus Schönit

Double rotary drilling combines continuous flight auger drilling with a casing for producing a cast-in-place pile. When producing a pile an outer casing and an auger (hollow auger) rotating inside the casing are driven into the ground in counter-rotation. The outer casing serves to support the surrounding soil and the inner auger excavates the drilling cuttings to the surface inside the casing. After reaching the projected drilling depth concrete is pumped through the hollow stem of the auger and outer casing and auger are extracted. After their complete extraction a reinforcement cage can be inserted in the fresh concrete. Compared to Kelly drilling the double rotary drilling method offers numerous advantages, including, for comparable diameter and length, shorter production times and higher accuracy (pile inclination and excess concrete) combined with increased occupational safety and lower noise emissions. Moreover, pile tests have proved that piles produced by double rotary drilling feature higher axial load-bearing capacities than comparable piles produced by Kelly drilling. This article offers an overview of the basic theoretical principles of double rotary drilling lists the required and currently available machinery and, finally, discusses the results and conclusions of a current jobsite.

Jan 1, 2011

By Eric R. Borys, Amaneh E. Kenarsari, Brett Gitskin

This case study discusses impacts of excessive Earth Retention System (ERS) lateral movement at a project in city of Chicago. The ERS (cantilevered sheeting) moved inward towards the excavation and caused lateral displacement and cracks in six drilled shafts located about 1 to 2 lateral feet (0.3 to 0.6 m) from the face of the sheet pile wall. Up to 9 inches (23 cm) of horizontal movement was observed on top of the supporting sheet-pile. Similarly, survey measurements showed the top of the drilled shafts moved laterally up to 8 inches (20.3 cm). To evaluate the cause of failure and determine a remediation solution, the soil, shaft and site conditions were investigated. Pile Integrity Tests (PIT) were conducted at the affected drilled shafts. The shafts with identified anomalies were cored and video-recorded. The cause of the failure was determined to be related to variable soil conditions across the site, deeper excavation (i.e., increased effective ERS wall height), and other differences between design and as-built conditions. Internal bracing, in the form of walers and rakers, was installed to limit further movement of the sheet pile as a short-term solution, with additional grade beams framed into the basement slab-on-grade as a long- term solution. Five of the six cracked shafts were spliced with reinforcing bars and high strength grout and one shaft was replaced. INTRODUCTION The subsoil in the Chicago Area mostly consists of glacial till clays underlain by water-bearing granular soil over bedrock. The glacial clays have very soft to medium consistencies for a typical thickness of 30 to 50 feet (9.1 to 15.2 m) below which hard clays (Hardpan, i.e., heavily over-consolidated clay soils) are encountered. The soft clays are often referred to as the “Chicago Blue Clay”. Beach Sands are also found above upper soft clays in several areas, especially within a three-mile strip near Lake Michigan (Peck and Reed 1954). Due to the existence of soft clay in Chicago area, supporting the mid to high rise buildings on drilled shafts extended to Hardpan is a common practice in modern building design. In the early 19th century it used to take about 3 weeks to excavate 1 shaft hole and about 1½ days to fill the shaft with concrete in Chicago (Manierre 1916). The early 19th century methodology of excavating a shaft consisted of hand digging the shaft, installing wood lagging as temporary shoring with spoils removed with a rope and pulley system from the surface. Today, the excavation of a typical drilled shaft in Chicago uses heavy drilling equipment and requires much less time for excavation and concrete placement. It is not uncommon for contractors to excavate shafts and place concrete at a rate of about 2 to 5 drilled shafts per day (with one drill rig).

Jan 1, 2018

Jan 1, 2001