Search Documents

By Dominique Vié

Standards methods covers the procedures for testing deep foundation to determine the force and velocity response to an impact of a pile driving hammer or similar device. The results of analysis generally include an assessment of pile integrity and the value of maximum dynamic stresses. But evaluation of static bearing capacity remains a matter of individual engineering judgment. A new 1D finite elements model has been developed for dynamic stresses and velocity analysis. Following an international benchmark of bearing capacity prediction organised by the Belgium Building Research Institute (BBRI), 12 piles in a site of fissured stiff tertiary clay tested in 1999, and 12 piles in a site of dense sand tested in 2001, comparison are proposed between analysis of dynamic tests and static tests results. A procedure is proposed to take in account the results of dynamic test for evaluation of bearing capacity.

Jan 1, 2002

Jan 1, 1987

By Kodi Ranga Swamy, N. Sankar, M. Akhila

"Until recently, liquefaction-related studies concentrated on clean sands believing that only sands are susceptible to liquefaction. However, a few earthquakes like 1976 Tangshan earthquake, the 1989 Loma Prieta earthquake, the 1999 Kocaeli earthquake, the 2010 Chile earthquake, and the 2011 Christchurch earthquake, etc. showed that sand with fines could also liquefy. The research findings on liquefaction of silty soils are limited, and several structures constructed on such soil deposits are damaged during the past earthquakes. Some previous results of research on earthquake events show an increase of liquefaction resistance in silt soils with increase the fines content, but some report the opposite trend. This study presents the results based on undrained triaxial cyclic tests which were carried out on the fine sand with fines (0%, 10%, 20% and 40% fines). The samples were prepared at the required unit weight (Dr = 50%) and saturated by using back pressure and cell pressure increments. Each consolidated sample is subjected to cyclic loading with sinusoidal wave load form at a frequency of 1 Hz. The liquefaction resistance is evaluated in terms of cyclic stress ratio required to cause 100% pore pressure or 20% failure strain occur at 15 numbers of load cycles. Results are presented in forms of pore pressure build up and axial strain propagation plots. As the fines content increased, an increase in liquefaction potential was observed.INTRODUCTIONLiquefaction and related phenomenon have been responsible for tremendous amounts of damage all around the world. In general, the liquefaction may occur in fully saturated sands, silts and low plastic clays. When the saturated soil mass is subjected to seismic or dynamic loads, there is a sudden buildup of pore water within a short duration, and it could not dissipate which leads to reducing the effective shear strength of soil mass. In this state, the soil mass behaves like a liquid and causes large deformations, settlements, flow failures, etc. This phenomenon is called soil liquefaction. As a result, the ability of soil deposit to support the foundations of buildings, bridges, dams, etc. is reduced. Liquefiable soil also exerts a higher pressure on retaining walls.This lateral movement of soil could cause settlement of the retained soil. A sudden build-up of pore water pressure during quake also triggers landslides. Liquefaction damages of structures are commonly observed in low-lying areas near the rivers, lakes, and oceans."

Jan 1, 2017

By Takashi Saito

Since early 1970?s skirt suction foundations (skirted foundation / bucket foundation) have been used as support for large fixed substructures or anchors for floating structures in offshore hydrocarbon development projects. In recent years skirt suction foundations are recognized as one of the solutions in foundations applicable to bridge substructures installed in waters, because skirt foundations have a wide variety of functions such as control of settlement during service life, less impact to environments during operation at installation site. This paper introduces general features of skirt suction foundations, and then discusses design practice of them for the application to bridge substructures, with reference to experiments in both laboratory and field.

Jan 1, 2013

By Rob van Dorp

"AbstractThe Monitoring & Instrumentation Committee (MIC) of DFI Europe has the objective to support DFI members in concern of risk management of geotechnical matters, where monitoring and instrumentation have added value.Work of the CommitteeA study by the committee showed that there are already several existing (national) guidelines. They all have their strengths and limitations and their focus may vary a little per country due to local regulations and typical local building activities, but the main question remains what added value another new guideline would have. More likely it would add to the confusion instead of providing overview.Companies with larger experience in geotechnical monitoring (often larger consultancy firm, contractors or clients) are already quite familiar with its benefits do not really need a new guideline in how to design and effectively apply sophisticated geotechnical monitoring systems for special projects.Therefore the aim of the MIC is to focus a little more towards smaller organizations - that are less familiar with monitoring and instrumentation - and the more ‘regular’ type of project that they are mainly involved in. The MIC wants to create a tool which helps them to create risk awareness, to understand the benefits of geotechnical monitoring and to provide them information about how and where to find the right partners and equipment to setup and apply appropriate monitoring systems for their projects.Monitoring and instrumentation benefits are for example:• Risk control during construction stage;• Costs reduction in design and construction (taken limitation of geotechnical aspects into account).• Prevent of unnecessary delays in construction work• Increasing general awareness of geotechnical risks and possibilities of monitoring.The cost of monitoring compared to the cost of failure and/or the savings that can be achieved play a role in the work of the committee. DFI members benefit from the shared knowledge by the MIC on monitoring and instrumentation within their process of risk management."

Jan 1, 2014

By Larry Rayburn

In the spring of 1999, construction commenced on the new Steelers Football Stadium in downtown Pittsburgh, Pennsylvania. Richard Goettle, Inc. (RGI) was the successful bidder to install the specified augercast piles for the foundation package. Description - Pittsburgh Steelers Stadium The new stadium will house the Pittsburgh Steelers Professional Football Team. It is widely believed that if a team is provided with a modern playing facility, that a winning season will ensue (Not always the case). The new stadium location is on the north side of Pittsburgh on the Ohio River, and just downstream of the confluence of the Monongahela and Allegheny Rivers. The site is west of existing Three Rivers Stadium. The Three Rivers Stadium was built during the late sixties and housed both the Pirates Baseball and Steelers Football Teams. The Public Auditorium Authority elected to replace this outdated stadium with two new stadiums, one for each professional team. The landmark stadium was imploded in February of 2001.

Jan 1, 2001

By John S. McCartney, Ismaail Ghaaowd

This study presents the results from centrifuge modeling experiments performed to understand the effects of temperature changes on the pullout capacity of scale-model energy piles embedded in normally- consolidated clay layers. The energy pile under investigation is an aluminum cylinder instrumented with internal strain gages and thermocouples, and its temperature is controlled using an internal electrical resistance heater. The energy pile was first heated until the temperature, pore water pressure, and volume change of the surrounding clay layer stabilized, after which the energy pile was cooled. Pullout tests were then performed on the energy piles heated to different temperatures to understand the effects of the preceding heating-cooling cycle on the pullout capacity. In addition, the clay undrained shear strength profiles were measured using push-pull T-bar penetration tests before and after heating. INTRODUCTION When a heat source such as an energy pile is embedded in a saturated clay layer, temperature changes will result in changes in pore water pressure as the rate of heating is typically faster than the rate of pore water drainage (Campanella & Mitchell 1968, Abuel-Naga et al. 2007, and Ghaaowd et al. 2016). Although all soils will initially expand during undrained heating, normally consolidated soils typically exhibit permanent contraction while overconsolidated soils exhibit expansion after sustained heating when drainage is allowed (Vega & McCartney 2015). Subsequent drained cooling typically leads to elastic contraction. Thermally- induced changes in pore water pressure and volume during transient heating and cooling may affect the soil- structure interaction of energy piles, as well as the ultimate capacity of the energy pile. This study is relevant as relatively few studies have been performed on the behavior of energy piles in soft clay (e.g., Ng et al. 2014), with most focused on the behavior of drilled shaft energy piles in stiff rock or overconsolidated clays (e.g., Laloui et al. 2006; Murphy et al. 2015; Wang et al. 2015; McCartney and Murphy 2017).

Jan 1, 2018

By Rudolph P. Frizzi

This paper presents different deep foundation systems and associated settlement records for high-rise building projects in the coastal areas of southeastern Florida. An introduction to the sedimentary soil and soft rock geology in coastal areas of southeast Florida is presented, and the deep foundation systems utilized include: piles of varying length, pile supported mat, preload and short piles, and drilled shafts. The implementation and associated settlement monitoring data of the different deep foundation systems are described through case histories involving 20 to 66-story buildings. In addition, the deep foundation systems and settlement monitoring results for twenty-one additional high-rise building projects in the coastal areas of southeastern Florida are presented.

Jan 1, 2003

Jan 1, 1998

By Wu Jie Mei, Li Yao Liang, Franz-Werner Gerressen, Arthur Bi

Diaphragm walls (D-walls) are known as underground structural elements commonly used for retention systems and permanent foundation elements. In addition, they are also quite often used as deep groundwater barriers, called Cut-Off-Walls (COW). Shanghai ranks third among the most densely populated metropolises in the world. In 1990, only eight million people lived there. Today, Shanghai has about25 million inhabitants. The increasing demand to accommodate the infrastructure of growing megacities like Shanghai pushes the required depth for subway, sewage and foundation projects to the limit. Future projects will demand excavation depths of more than 100 m (328 ft) on a regular basis. Already carried out reference projects will be described and a general outlook for upcoming projects will be given. The paper also explains the installation process in general focusing on the use of trench cutter technology. INTRODUCTION D- walls are known as underground structural elements, commonly used as retention systems for excavation pits and shafts as well as permanent foundation walls or elements. It is anticipated that, with the increasing trend of utilizing more and more underground space to accommodate environmental considerations and urban/suburban development, there will be an increasing requirement for diaphragm wall usage in even more difficult conditions and with increasing depth. The trench cutter is the most important tool for performing this work. The hydraulic grab, a well-known and valuable excavation tool for d-walls reaches its limits in terms of depth and when cutting rock. Therefore the trench cutter technology will be in the focus of this paper. The trench cutter itself is a reverse circulation excavation tool. It consists of a heavy steel frame with two drive gears attached to its bottom end, which rotates in opposite direction around the horizontal axis. Cutter wheels are mounted onto the drive gears. As they rotate, the soil beneath the cutter wheels is continuously broken up, removed, mixed with the bentonite slurry in the trench and moved towards the opening of the suction box of the pump? A centrifugal pump located right above the cutter wheels conveys the slurry via a hose system up to a desanding plant. There the slurry loaded with soil and rock particles is cleaned and returned into the trench.

Jan 1, 2018

By Kazimierz Gwizdala

In recent years, in Poland the ATLAS piles have been successfully applied for some constructions near Gdansk. The piles have been used as foundations for housing and another areas of civil engineering, in delta Vistula geotechnical region, characterized by weak, highly compressible soils represented by mud and peat, lying in sub-surface layers, several meters thick. Usually below are dense sandy soils or gravel. In all cases, the base of ATLAS piles rested on sandy soils. The analysis of pile bearing capacity has been discussed and verified by static pile load tests (SPLT). The load-settlements characteristics obtained were satisfactory. In the paper, the results of geotechnical investigations as well as calculations and load tests are shown. The ecological aspects of ATLAS piles application within highly urban areas of the cities and complex geotechnical conditions are emphasized.

Jan 1, 2006

By Vincent Joannes, Marine Lasne, Luca Brenelli, Colin Serridge, Inge van Baardwijk, Martin Stanley, Anthony Fisher, Mary Ellen Bruce, Tony Suckling, Pedro Avellanosa

"Abstract The European Federation of Foundation Contractors (EFFC) and Deep Foundations Institute (DFI) developed a sector-specific carbon accounting methodology and associated “carbon calculator” for foundations and geotechnical works. The EFFC-DFI Carbon Calculator is believed to be one of the construction industry’s first collaboratively produced carbon calculator tools for European and international countries based on verifiable and standardized data. It is intended that the tool be adopted internationally and become the open-source industry standard for ground works. A detailed methodological guide is provided with the calculator (Lemaignan and Wilmotte, 2013). This guide explains the background of the standards, accounting methodologies, emission sources and factors that were used as the bases for the tool development and includes detailed guidance on use of the calculator.Drivers for DevelopmentFoundation contractors anticipate project cost and carbon emissions will become inextricably linked in response to the climbing price of fossil fuels and carbon intensive materials as resources become scarce. Low carbon solutions will therefore become more competitive options. Also with high profile construction projects having low carbon/carbon neutrality as requirements, sustainability in the foundations industry also becomes a market issue.This carbon calculator will be used to lead the industry and shape the expectations of commissioning organisations by providing insight into the carbon cost of their projects. Commissioning organizations are encouraged to be aware of the carbon impact of projects and to also facilitate a fair and accurate way of comparing footprints to provide a level playing field for foundation contractors."

Jan 1, 2014

By Marius B. Wechsler

There are considered deep piles which are fixed in blocks of rotating machinery foundations. A mathematical background is developed for determining the behavior of this kind of piles for motions caused by horizontal and vertical oscillations, as well as by roc-king and twisting. It is assumed that the piles come across a top soil layer of depth c, not capable of lateral support, and penetrate over a length b, in a bottom firm soil layer, or in a bottom soft soil layer in which vibrations can produce voids around the piles. With respect to b and c, as well as to the elastic properties of piles and soils, the analysis leads to the maximum bending moments and shear forces subjecting the piles, to the maximum lateral bearing on the bottom soil layer, as well as to the deflection of the pile and the displacement of the foundation block. The results of the performed analysis can be applied to seismic loads too, and they are illustrated by a numerical example.

Jan 1, 1987

By D. Michael Holloway

The realignment of Interstate 880 replaces the double-decked (Cypress) viaduct collapsed in Oakland, California during the 1989 Loma Prieta Earthquake. The California Department of Transportation (CALTRANS) evaluated several pile foundation schemes for supporting the proposed structures. Structural support demands led to the selection of steel pipe piles (16-, 24-, and 42-inch-(406-, 610- and 1067-mm-)diameter), filled with concrete and steel reinforcement. Deep penetrations required through layers of very dense/cemented sands in some locations, caused serious drivability and pile integrity concerns. The need for large pile driving hammers and large diameter steel pipe piles pushed the engineers and prospective contractors well beyond the limits of local experience. Such questions as the feasibility of driving the pipes closed-ended through dense upper strata, and quantifying the effects of installation on the long-term capacities of the piles, led CALTRANS to develop a comprehensive pile test program to address the design and construction issues effectively. The results were furnished to prospective bidders on the production stages of the ensuing contracts.

Jan 1, 1996

By [D. N. ] Naresh

During different activities pile installation like pile boring, concreting etc., it is likely that various problems, depending up on site condition may be encountered. There are possibilities that some of the activities if not correctly followed may affect the pile capacity. This paper describes few problems encountered during pile execution at different sites and presents the remedial measures undertaken to overcome them.

Jan 1, 1996

By R. Stenne

This paper presents the trends in deep foundations in Europe, both in terms of design and construction. Eurocode 7 which is a design code for geotechnical engineering will be introduced in the European Union member countries, and will oblige geotechnical engineers to abandon traditional methods based on a global factor and adopt a new approach based on partial factors of safety. Execution codes (for construction of foundations and other geotechnical processes) are currently being introduced without problems. Ever more demanding environmental constraints push foundation contractors to adapt old techniques and develop new ones to comply with new regulations.

Jan 1, 2000

By Edmund J. Cardoza

The paper describes the design, construction and quality control aspects of the installation of a cement-bentonite (CB) cut off wall to impede seepage through a flood control dike. Special emphasis is placed upon the development of a proper specification, distinguishing the CB method from the Soil-Bentonite technique. The importance of the pre-construction laboratory testing program and field quality control procedures is emphasized by the fact that the in-place properties and characteristics of the CB cut off may not be known until after a majority of the work is complete. Sections are included which describe the construction method, the specialty equipment and personnel requirements and the quality control/quality assurance aspects of the project.

Jan 1, 1992

By Bolestaw A. Ktosihski

Preloading of bored pile bases by grouting is an effective way of reducing foundation costs. The bearing performance of a pile may be considerably improved. Various techniques and devices are used. Preloading of a pile base by a special grouting installation is preferred. The grouting device consisting of a U-shaped grouting tube with sleeves and a plastic membrane, separating the tube from the pile concrete, has well proven in Polish practice. The preloading may raise the pile design loads by as much as 30%, and increase their stiffness by 50%, in suitable conditions. The preloading equalizes the deformability of piles in a foundation or a structure. Examples of the base preloading use and load tests of base grouted piles are presented.

Jan 1, 2006

By A. Boominathan

The behaviour of single piles under lateral dynamic loading is very critical and the study is still a current field of research since 1950's. Though many methods have been developed analytically to estimate the dynamic lateral stiffness, very limited dynamic testing on full scale piles were carried out to study the response of piles under lateral dynamic loading. Hence, field lateral dynamic vibration tests are conducted on driven precast concrete square pile of 400mm size and driven cast in-situ concrete piles of 400mm and 500 mm diameter at a petrochemical complexes site at Haldia (India). The results of steady state and free vibrations tests are discussed herein and compared with the response of the piles estimated from PILAY.

Jan 1, 2002

By Bruce Haldeman

Timber has been used as pile support for structures for 6,000 years. Some means of preservation of wood go back almost that far. Timber piles support all types of structures ? some are buried below the water table; others raise a home for protection from animals or a chief's home for prestige. Millions of wood piles have been driven for bridge support. Earlier piles were driven by hand then by ingeniously raised weights. Charring, animal fats and oils have been used for preservation. Coal tar creosote and other preservative methods started only in the early 1800's and give effective protection.

Jan 1, 1984