Search Documents

By M. Nomura

This paper describes the results and field measurements of two long-term observation tests and two short-term loading tests to confirm the effectiveness of NF piles in reducing negative skin friction. All the test piles were equipped with strain gauges, allowing measurement of the compressive axial forces in the piles. These test results prove that NF piles are effective in reducing the negative skin friction to an insignificant value. Some examples of the design procedures used in Hong Kong and Japan are also presented.

Jan 1, 2010

By Z. C. Chen

Based on the analysis of load test data of long floating piles in soft soil regions, the expressions of load-transfer function of pile shaft and tip for soft soils are presented in this paper, and the data of cone penetration test are suggested to use for calculating the parameters of load-transfer functions. For the loads of pile within the range of the working load of pile, the estimated pile stiffness by the suggested method in this paper are in satisfactory agreement with the results of load tests. The current Vijayvergiya's method and Satowa's method also are used to calculate pile stiffness in soft soil for comparison.

Jan 1, 2010

By Adrian Mercer, Ashkan Ameri

Due to general degradation, increased traffic levels, and historical ground movement, this road and rail bridge which provides an essential link between the interior of the country and the Port of Abidjan, required significant repair and reinforcement. This included strengthening the pre-stressed concrete box girders and replacement of the existing bored pile foundations. Replacement piles had to be adjacent to, and no longer than, the existing piles, in order to not compromise the stability of the operational bridge during the works. The underlying geology, however, meant that the pile loads had to be predominantly transferred into the ground through end bearing. Rather than installing a greater number of piles or larger diameter piles, innovative thinking changed the usual mind-set of designing the piles to the prevailing ground conditions, to designing the ground conditions to suit the piles. Jet grouted columns were installed beneath the toes of the new piles to increase the bearing capacity of the ground. This significantly contributed to the sustainability of the project and reduced carbon emissions through saving concrete, steel, plus transportation and disposal of spoil.

Sep 8, 2021

By Patrick E. Durnal, Henrik Dahl

"A joint venture of Ben C. Gerwick Inc., Sverdrup (now Jacobs) and DMJM (now DMJM + Harris) designed the $779 million seismic upgrade of the Richmond - San Rafael Bridge over the San Pablo Bay in the San Francisco Bay Area and provided construction support to Caltrans. Construction of the marine foundation retrofi t was completed by a joint venture of Tudor Saliba/Tidewater/Koch-Skanska and their subcontractors: Pomeroy Precast Construction, AGRA Foundations, Dutra Construction and Vortex Divers. Construction management and inspection was performed by Caltrans with the support of various consultants. MARINE FOUNDATION RETROFIT SCOPEThe retrofi t design of the submerged foundations included:??A total of 476 tension and compression micro piles (290- 1140 kips or 1290-5071 kN) installed through cored holes through the underwater bells at 31 pier locations??Fourteen 126/150/164 inch (3.20/3.81/4.17m) diameter CISS (Cast-in-steel shell) concrete shear piles (1160- 2660 kips or 5160-11832 kN) installed through new precast concrete pile cap extensions??Twelve CIDH (Cast-in-drilled-hole) shear piles (1060- 2130 kips or 4715-9475 kN) with 150 inch (3.91m) diameter steel shells to top of bedrock and 30 ft (9,14m) long and 11 ft (3.35m) diameter rock socket installed through new precast concrete pile cap extensions The specifi ed post bid test boring revealed deeper bedrock at one pier location allowing deletion of the rock socket. Thus 15 CISS and 11 CIDH shear piles were installed at 11 pier locations - 9 piers with 2 piles and 2 piers with 4 piles. Cut off elevations for the shear piles ranged from 46 ft to 60 ft (14.0m to 18.3m) below mean sea level and cut off for the micro piles was 8 ft to 46 ft (2.44m to 14.0m) below mean sea level. Almost all foundation retrofi ts required work under limited headroom conditions. Underwater construction connections required innovative design details and construction techniques for each pile type. The 11 piers had 22 precast concrete pile cap extensions installed in pairs and connected by either tremie concrete closure pours or by large pipe struts. The precast pile cap extensions were strapped underwater using large steel bands wrapping around the belled piers with grouted annulus. The precast pile caps were founded with 14 inch (355mm) diameter steel pipe piles, which were either support piles or seismic tension and compression piles. The seismic piles were connected in grouted corrugated steel pipe sleeves cast into the new concrete pile caps."

Jan 1, 2007

By Amr Sallam, David Thompson, Moataz Hassan

"The Little Lake Harris (LLH) Bridge was constructed in 1951 to replace the eastwest County Road 48 Bridge connecting the towns of Howey-in-the-Hills and Astatula in Lake County, Florida, United States. The 78-span bridge carries two lanes of traffic, is 3,130 feet long, and 36.1 feet wide. The concrete deck is supported by steel I-girders carried by one row of 18-inch square precast concrete driven pile. In the late 1980's, slight settlements were observed in several bents. In 1990, Florida Department of Transportation (FDOT) initiated annual survey of deck elevations during bridge inspections to monitor settlement. Due to the slow nature and magnitude of settlement, substructure instability was not a major concern to the department. However, public concern over the settlement and rough ride of the bridge continued to rise. FDOT contracted Kisinger Campo & Associates Corp. (KCA) to provide the needed design to correct the dips in the riding surface and minimize future settlement. KCA's initial design was based on the concept of ""helper bents"" at the settled bents in order to restore the bridge to original elevation. Estimated construction cost for seven helper bents was about $3.3M. FDOT requested evaluating other alternatives to reduce the cost of the bridge restoration. KCA involved the geotechnical consultant, Terracon Consultants, Inc. (Terracon), to perform a peer review and provide an economical alternative solution. Jacking and shimming the bridge was determined to be both technically viable and economical with a total cost of less than $300K. The design was completed in March 2010 and construction was completed in February 2011. This paper provides an overview of the LLH Bridge history, summarizes the evolution of the design methodology including the findings of the geotechnical study and presents lessons learned during the design and construction of the project.INTRODUCTIONThe Safety and Preservation of the State Highway System is the top priority of the FDOT. Therefore, FDOT initiated a bridge management program that starts with conducting biennial safety inspections performed by Certified Bridge Inspectors (CBI). The inspection reports together with the CBI’s recommendations are reviewed by a registered Professional Engineer (PE) and work orders are issued with priority ranking depending on the severity of the bridge deficiencies. If the scope of work is considered beyond the in-house crews’ capability, the work is then included in a contract for and bid. LLH Bridge was a little different. It was initiated in direct response to number of complaints the FDOT District 5 Structures Maintenance Office (D5SMO) received regarding settlement of the Little Lake Harris Bridge."

Jan 1, 2015

By Lawrence F. Johnsen, Marc J. Gallagher

"Micropiles are small diameter, bored, grouted-in-place piles incorporating steel casing and/or reinforcements. The omission of micropiles from most United States building codes has resulted in the application of varying standards for design and installation. The ADSC/DFI Micropile Committee has developed a proposed section for the 2006 edition of the International Building Code (IBC 2006) covering micropiles. The proposed IBC 2006 micropile code section is presented, along with comparisons to existing micropile codes and guidelines. A discussion section is provided to clarify sections of the proposed code. IntroductionMicropiles, defined as small diameter (typically less than 12 inches outer diameter), bored, grouted-in-place piles incorporating steel casing and/or reinforcements, are becoming common foundation elements for new construction, retrofits, and emergency repairs. Developed in Europe in the 1950's and used in United States practice since the late 1970's, micropiles are typically not addressed in building codes, particularly in the United States. As a result, micropiles are often reviewed by building officials to a variety of standards, including drilled shafts, caissons, cast-in-place bored piles, and concrete filled pipe piles. None of these adequately address the unique design and construction aspects of micropiles. Therefore, it became apparent to the foundation design and construction community that a micropile-specific code section was required.To that end, the International Association of Foundation Drilling and the Deep Foundations Institute (ADSC/DFI) Micropile Committee appointed a subcommittee in October 2003 to develop and submit a proposed micropile code section for the 2006 IBC. The subcommittee members included the two co-authors, as well as Tom Richards (Nicholson Construction Company), Tom Armour (DBM Contractors, Inc.), John Wolosick (Hayward Baker, Inc.), Allen Cadden (Schnabel Engineering) and Matt Niermann (Schnabel Foundation Company). At the time of the writing of this paper, the proposed code section has been presented at the IBC public hearing during which it was modified slightly. Final adoption (or rejection) will be determined by the IBC at the final action hearing in September 2005. The attached code section is the revised version following the public review hearings."

Jan 1, 2005

By R. K. Filip

"Steel bearing piles have long been used to carry high compressive, tensile and lateral loads. Such piles are most commonly tubular or ""H"" profile and are typically installed using percussive techniques. The noise and vibration associated with such installation techniques tends to preclude the use of steel bearing piles in urban and other sensitive areas.This paper describes the design and construction of an innovative new road bridge in Milton Keynes, UK. The steel bearing piles were required to continue out of the ground to form the bridge columns and abutments and then be cast directly into the soffit of the reinforced concrete bridge deck. This project was to be the first time in the UK, that this form of bridge design had been used.The paper shows how new installation techniques allowed the designers to use these high capacity steel elements in a sensitive urban environment without the use of percussive or vibratory installation techniques. Finally the paper shows how these quiet and vibration-less installation techniques can be extended to other applications.A UNIQUE BRIDGE SUPPORTED ON ""BOXED SHEET PILES""CONCEPT HISTORYThere are over 700 bridges in Milton Keynes. Concrete is the dominant construction material, most are single span with massive parallel wing wall retaining abutments. All have a certain uniformity of aesthetic design. Pell Frischmann Consultants Ltd (PFC) proposed to the client, English Partnerships (EP), that an ""integral bridge"" with a slender open appearance would be an appropriate aesthetic form for a new highways bridge, within the district of Westcroft (figure 1). The concept required that the bearing piles be continued up out of the ground to form the bridge columns and abutments. Four rows with four piles in each row were suggested. Each would then be cast directly into the reinforced concrete bridge deck forming a moment connection (figure 2). This concept meant that a single continuous steel structural member would replace traditional reinforced concrete bored piles, pile caps and piers. This member would carry vertical and lateral loads. The conceptual design was intended to meet the following client requirements:"

Jan 1, 2005

By Andres M. Baquerizo, Matthew E. Meyer, Carlos Ortiz

"The Metropolitan Miami development, a downtown mixed-use complex developed by Miami-based MDM Development Group, has weathered the economic downturn by adapting to the needs and pressures of the local market. The development (a.k.a. Met Miami) epitomizes the term “mixed-use urban development” with its combination of condominium ownership, rental apartments, hospitality, office and retail components within Miami’s urban core. Initially conceived and conceptualized in 2004, the development has gone through several concept changes. Today, the global USD $900 million development approaches completion.The foundation evaluation, design and construction for this development included the use of innovative and state-of-the-art augered-cast-in-place (ACIP) piles. The testing for these elements included (1) the first-ever, multi-level O-cell load test of an ACIP pile, (2) a world record 5,200 ton (46,261.5 kN) equivalent top load test of an ACIP pile, and (3) continued the advancement of the ACIP pile industry to include the deepest and largest diameter pile installation to date. Those dimensions were up to 36 in (914 mm) in diameter, and 120 ft (36.6 m) deep. The project showed ACIP piles were a proven alternative for structures exceeding 70 stories in South Florida.The development includes four parcels. Met 1 and Met 2 are completed, and the construction of the Met 3 development is just beginning, with completion expected in 2014. Once the Met 3 development is completed, the design and construction phases of the project will have spanned a decade. The Met Square portion of the development, which will be a retail and cinema component, is proposed for the parcel between Met 1 and Met 2."

Jan 1, 2012

By Mohamed Hassan, Matthias Seip, Steffen Leppla

In the east of Frankfurt am Main, Germany, a new high-rise building is planned directly next to the river Main. The high-rise building will have a height of about 75 m and will be founded on a Combined Pile-Raft Foundation (CPRF) in the tertiary marl. The new structure will be constructed next to important, sensitive traffic infrastructure. The foundation of the new high-rise building adjoins directly existing historic quay structures, which are more than 100 years old. For analysis of the stability and the serviceability of the heavily eccentric loaded foundation of the new high-rise building and the existing structures and for the investigation of the soil-structure interaction complex three dimensional, non-linear numerical simulations have been carried out. These numerical simulations take into account all geometric and material specific boundary conditions, including the history of the construction of the whole area. The paper introduces into a very complex construction project in which the investigation of the soil-structure interaction has an important role. The three-dimensional numerical simulations are explained and the results are shown.

May 1, 2022

By Paul Suver

"The closed loop standing column well (CLSCW) system uses a closed circuit of water to develop the same thermal heat exchange characteristics that are achieved from traditional open circuit standing column well that uses the ground water directly. Pipe pile and pipe anchor foundations can be used as CLSCW components for ground source heat exchange. New data gathering and analysis techniques and equipment installed in the heat pumps allow any mechanical engineer to design the system without specialty engineering equipment and certifications.CLSCW Description:Closed end steel pipe of varying outer diameter (O.D.) is installed by various technologies at varying depths depending on subsurface geology. The wells are arranged as stand alone wells or in groups joined in parallel or in series or in a combination of both. These pipes may also serve a dual function as foundation supports, deep foundation pile, anchors or earth retention components. These wells are then internally coated to minimize corrosion. The wells are then plumbed and capped to create a vessel equipped with a supply and return water line.The stand alone well or group of wells is then used as a ground heat exchanger for a ground source heat pumps located in or around the building.The ground source heat pumps provide heating and cooling to the building either with a traditional ducted distribution system or with radiant heating and cooling. These systems can reach efficiencies three times greater than traditional gas fired heat sources and five times greater than traditional air conditioning sources."

Jan 1, 2017

By Naoyuki Hanawa, Takeo Asanuma, Tatsuo Nagatsu, Sachihiko Tokunaga, Daisuke Nakagawa, Yoshiyuki Morikawa, Kazuhiko Ueno

"In the cement deep mixing (CDM) method, one approach to joint construction is creating a surface-contact joint. In this study, an unconsolidated-undrained triaxial compression test was performed on cement-treated soil specimens with joints artificially created by successive pouring. The effects of the presence or absence of such successive pouring joints on the strength of the specimens were then examined. The results showed that the compressive strength of the specimen decreased by approximately 0%–30% with a successive pouring joint.INTRODUCTIONIn the block type and wall type improvement patterns of the CDM(Cement Deep Mixing Method) application, an integrated body of soil-cement columns is constructed by partially overlapping individual treated soil columns. The overlapping operation should be implemented before the hardening of soils by cement progresses and thus, this operation is routinely performed in construction sites usually within 24 hours or within 48 hours at a maximum. However, when the operation is forced to be interrupted on account of a typhoon or any other adverse weather conditions, it is impossible to carry out the overlapping operation within the above time limitations. In such a case, it is necessary to improve the integrity between the treated soil columns solidified first and the treated soil columns to be constructed later.One of the methods that can be adopted is to prior agitate the target area by mixing blades “without cement”, integrating the preceding treated soil columns and the subsequently treated soil columns at construction joints. This method has been adopted so far in numerous sites because no additional materials or equipment are necessary. However, its effectiveness has scarcely been evaluated quantitatively in conventional studies.In the circumstances, the authors investigated in the present research the effect of the presence or absence of construction joints on the specimen strength by performing unconsolidated-undrained triaxial compression tests using specimens of cement treated soil artificially provided with surface-abutting construction joints.Therefore, this study examined the effects of the presence or absence of artificially created successive pouring joints on the strength of cement-treated soil specimens through an unconsolidated-undrained triaxial compression test."

Jan 1, 2015

By Massimo Poggio, Gabriele Balconi, Andrea M. R. Pettinaroli, Mario Ruggiero, Riccardo Castellanza

Grouting technologies are ground treatment techniques used for modifying the behaviour of a mass of soil or rock by injecting a mixture. The sleeved port pipes (also called Tube A Manchette) are highly diffused for grouting treatment of coarse soils and fissured rocks. This paper describes a combination of jet grouting and rock grouting with MPSP (multiple packer sleeve pipe) technique that has been used to realize waterproof curtains under fluvial structures for a cascade hydro-power plant. This is composed by five mini hydro-power plants, placed along the Iskar River, in Bulgaria, and composed by a penstock followed by the power house, a spillway, and an earth dam containing the reservoir. The geology of the site is characterized by an upper alluvial deposit lying over the bedrock. In each site, similar treatments were carried out: an impervious curtain along the plant section, obtained by executing jet-grouting columns in the surficial alluvial layers and grouting the underlying fractured rock by means of port pipes. The temporary embankment, built during the works for protecting each site from the possible river floods, has been waterproofed and stabilized by reinforced jet-grouting columns. The grouting processes have been controlled and monitored by a computerized system. INTRODUCTION The Iskar river cascade hydropower plant is situated northern of Sofia, Bulgaria, and it is composed by nine plants. Actually five of them have been built and produce energy. Each plant is composed by a penstock followed by the turbine building, a spillway, and an earth dam that contains the reservoir. The Iskar rivers runs in a narrow valley characterized by diorite or diabase rocks, with an upper deposit of alluvial soil, composed mainly by gravel and sand. Each plant requires an impervious curtain under the structures and in correspondence of the earth dam: this has been obtained by means of a jet grouting treatment of the alluvial coarse soil, and a grouting treatment with cement mixtures of the underlying rock using the MPSP technology. During the construction of the structures, the site has been shielded from the river water by a temporary earth embankment that has been statically improved and waterproofed by jet grouting columns reinforced with steel tubes; this allowed to work without interruption even in case of flood of the Iskar river.

Jan 1, 2019

By Brian T. Nereson, Michael C. Penney

"This technical paper was prepared to describe the general process by which the authors designed a column-supported load transfer platform (LTP) for support of asphalt-paved runway and taxiway embankment areas over soft organic soils, the major tasks and observations made during construction of the system, and the outcome of the system design and construction. The LTP system was designed using the method described in the BSI Standards Publication Code of Practice for Strengthened/Reinforced Soils and Other Fills, BS 8006-1:2010 (BS8006), to achieve performance objectives for the project. The design also used other criteria based upon the authors’ engineering experience and understanding of the expected interaction between soils, structures and geotextiles. The design and construction process described herein resulted in a successful project. The authors identified that full-time engineering oversight during construction was of high importance and provided a high degree of value to the project. The authors’ intimate knowledge of the potentially adverse effects of variations in construction practices promoted timely identification of construction deficiencies that could have affected the reliability of the system. This resulted in corrections and modifications being made, while materials were still accessible, to protect the intended performance of the finished system.INTRODUCTIONThe site is located in Marshfield, Massachusetts. The surrounding area is flat and contains significant wetlands with a water table at or near the ground surface. Prior to the improvements described herein, the site was already developed as an existing municipal airport with an approximately 3,000 linear-feet asphalt-paved runway oriented in a northeast/southwest direction (northeast end referred to as Runway 24 and southwest end referred to as Runway 6; Fig. 1). The site is located approximately 0.5 to 1 mile (Runway 24 and Runway 6, respectively) from the Atlantic Ocean.The improvement project included total extension of approximately 550 linear feet of asphalt-paved runways and taxiways over existing wetlands that consisted of soft, organic soils with varying but significant depths (Fig. 2). An initial geotechnical assessment performed for the project identified that the subsurface conditions were not suitable to support the proposed runways and taxiways in their existing state."

Jan 1, 2016

By Michael Cianchetti, Nadir Ansari, Matthew Janes

"PROJECT DESCRIPTIONThe R C Harris Filtration Plant underwent an expansion to install an underground sludge treatment capability consisting of a series of underground tanks within stepped excavations 12m (39 ft) and 10m (33 ft) deep into compact, wet sands over stiff clays and clayey silts.Concerns regarding the original structure influenced designers to set the lateral deflection limit for the proximal front footing at 4mm (1/6 in), (0.03% excavation depth). The design-build team indicated at the time of tender that the movement criteria was unattainable using the tender design. Through extensive Fast Lagrangian Analysis on Continua (FLAC) and a novel construction geometry the design-build team crafted an alternative that produced significant savings over the original concept and met deflection concerns.GEOTECHNIQUEThe hillside site drops 14.5m (47.6 ft) over a distance of 53m (174 ft) between the existing Filter Building on the north and the Services Building on the south. The soils adjacent to the Filter Building consist of 6m (20 ft) of sandy fills, to the footing elevation, over compact sands and layered dense sands and silts to a depth of 10m (33 ft) below existing footing. Beneath the silts lies a 10m (33 ft) thick stiff clayey silt, 2m (6.6 ft) of sandy silt till (containing cobbles and boulders) and an artesian gravelly sand at a total depth of 30m (98.5 ft).The tender information was deemed inadequate to accurately determine soil parameters for a finite element analysis. As a result, the design-build team performed pre-tender Cone Penetrometer Testing (CPT), including dynamic analysis. The CPT data indicated stratigraphy consistent with the conventional bore hole exploration (SPT results) however, the CPT data provided consistently superior soil strengths. The CPT data indicated the sands and silts were dense to very dense throughout their full thickness. The clayey silts below the sands were found to have shear strengths in the 100 to 200 kPa (14.5 to 29 psi) range with an Over-Consolidation Ratio (OCR) ratio of 1.5 to 2. The dynamic analysis, while low strain, indicated very competent behavior with Young’s Modulus values in the 200 to 350 MPa (29,000 psi to 51,000 psi) range. The CPT derived shear moduli and OCR values were vital in determining the soil engineering parameters used for the FLAC analyses."

Jan 1, 2007

By Norm Kirk, Robert Bittner

"The addition of a new powerhouse at the existing Tulloch Hydroelectric site on the Stanislaus River in the western foothills of the Sierras Nevada Mountains of central California required a deep excavation in rock on the downstream face of the dam. A cofferdam (water exclusion device) was necessary to isolate the powerhouse construction site excavation from the existing Goodwin Reservoir and the turbulent discharge from the existing powerhouse. The cofferdam was positioned on a steeply sloping fractured rock surface exceeding 50 degrees.This paper describes the challenges encountered during design and construction of the cofferdam and describes the unique design features used to address these challenges including:•,The use of flat-sheet-piles to form cellular walls on the steeply sloping rock surface.•,The use of 5-ft deep tremie concrete plugs in the bottom of the sheet pocket cells to create the bottom seal of the cellular cofferdam walls against the sloping rock surface.•,The use of vertical post-tensioned rock anchors to provide shear resistance at the contact point between the base of the cellular-wall and the sloping rocksurface.INTRODUCTIONModification or expansion of existing hydroelectric power plants often require downstream cofferdams or water exclusion devices to temporarily separate new construction from turbulent downstream discharge of the existing dam. Most dams are positioned on solid rock in the narrowest and therefore the steepest section of the river. This combination of steeply slopingrock and the need for an exclusion barrier creates a challenge for the design engineer trying to maintain a safe dewatered construction site. Typical cofferdam solutions for hydroelectric dams usually use large granular filled circular sheet pile cells that perform as gravity structures. However, this type of structures is not well suited to steeply-sloping highly irregular rock surfaces in a confined area."

Jan 1, 2017

By Paul Suver

The closed loop standing column well (CLSCW) system uses a closed circuit of water to develop the same thermal heat exchange characteristics that are achieved from traditional open circuit standing column well that uses the ground water directly. Pipe pile and pipe anchor foundations can be used as CLSCW components for ground source heat exchange. New data gathering and analysis techniques and equipment installed in the heat pumps allow any mechanical engineer to design the system without specialty engineering equipment and certifications.

By James Warner

Investigations of the sinkhole indicated that the loose, disturbed ground was completely encircled by dense competent core. This confinement substantially increased the effectiveness of the compaction grouting compared to what might have been expected at a "greenfield" site. However, the 8 ft diameter circle shown in the plan view was only the surface expression of the sinkhole proper and the deep, loosened ground actually extended to a larger diameter of about 20 ft. The planned spacing of the grout holes was based on the finite element simulations using a target void ratio of less than 0.3 throughout the compacted ground within a 5 ft radius of the grout injection point. Because of the strong confinement effect, the layout of grout holes included one central primary hole surrounded by six secondary holes at a triangular spacing of about 5 ft. Since the disturbed ground was considered a confined cylinder, it was anticipated that the primary hole would perform the majority of work and the secondary holes would act as check holes, with progressively lesser grout takes as the loose ground densified.

Feb 10, 2003

By Kamil Nuzha, Jianchao Li, Bashar S. Qubain

"The Philadelphia Water Department is rehabilitating Belmont Raw Water Basin. As part of this work, a 500-ft long, temporary cofferdam was designed to retain 35 ft of combined water and soil at the western half during the reconstruction of the eastern half. A cofferdam that comprises two integral rows of sheet piles was selected to take advantage of the soil’s weight between the sheet piles for increased stability. To fine tune the design, a geotechnical investigation was carried out to verify the subsurface conditions and, in particular, the top of rock variations along the centerline of the cofferdam. A detailed finite element analysis was performed based on the subsurface findings and incorporating the construction sequence to evaluate the behavior of the cofferdam at the following stages: installation of tie rods to connect to the two rows of sheet piles; partial excavation and installation of tiebacks; complete excavation of the east basin, and demolition of the cofferdam. Inclinometers and survey markers were installed every 100 ft along the cofferdam and were monitored throughout construction. The deformation measurements were in good agreement with the finite element results.INTRODUCTIONThe Philadelphia Water Department (PWD) Belmont Raw Water Basin is located at the intersection of City Line and Belmont Avenues in Philadelphia, PA. The facility actually contains two raw water basins, east and west, separated by an earthen dividing dike. Water leakage at the bottom of the basins and through the dividing dike together with increasing demand for a larger storage capacity dictated the replacement of the wide earthen dike with new narrower concrete structure. The temporary cofferdam was designed for a two-year period to facilitate excavation support, water cutoff, removal of the existing earthen dike and replacing it with a new concrete dike. During this construction sequence, the water level in the west basin had to be maintained at or near its full capacity.Various excavation support systems were considered for this project prior to the selection of a double wall sheet pile cofferdam. Fig. 1 shows a plan view of the cofferdam and the new dividing dike. A typical cross section of the two structures is shown in Fig. 2. Double row sheet pile walls are commonly used as both temporary and permanent retaining systems in open water applications such as construction works, quaywalls, breakwaters and revetments for storing industrial waste as indicated by Ohori, et al. (1984), Ohori et al. (1988), and Khan, et al. (2001). There are many advantages to double row sheet pile systems as recognized by Ohori, et al. (1984; 1988): (1) It can be installed and removed in the presence of water easily and quickly; (2) it provides stability with small width to height ratio, utilizing the existing soils between the installed sheet pile rows; and (3) it serves well as a means for water cutoff. These advantages meet the specific project requirements."

Jan 1, 2016

By Mark Spence, Tom Lardner, Matthew Janes

"IntroductionThe design-build method streamlines project delivery through a single contract between the Contract manager and the design-build team. The design-build method places emphasis on collaborative project management between design and construction disciplines to minimize project schedule, reduce costs, encourage balance risk amongst the design-build team. Since 1985, the percentage of nonresidential design and construction projects has increased from 5% to 45%.1A project carried out in Edmonton, Alberta, Canada will be used as an example to illustrate the challenges of the design-build project delivery method and the merits of establishing a GBR. The project involved a complex slope stabilization as part of an extensive freeway widening. At the project location the roadway was being widened within the base of a historic stream valley into a steep slope with a history of a previous slope failure. The slope was to be steepened through the installation of a series of 14 interlocking arc structures constructed half way up the slope. Access and schedule proved critical to the successful completion of the project.Geotechnique and Site HistoryThe geotechnical investigation undertaken for the site included six boreholes drilled at the crest of the slope to depths ranging from 14.5 m to 30.2 m. Laboratory testing of the soil samples included direct shear tests, Atterberg limits and grain size analysis. The geotechnical report also referenced a previous geotechnical investigation that was carried out in response to a failure of the slope in 1971."

Jan 1, 2015

By Donald T. Robertson, Kurt Hecht, Michael K. Muchard

"This paper presents case histories of driven concrete pile damage detected with dynamic testing methods utilizing strain gages and accelerometers embedded in the pile at the prestressing yard during pile construction. Data from the embedded instrumentation is compared with data taken with external bolt on instrumentation and other test methods such as low strain testing on the same pile. In the most severe cases, the piles were extracted revealing and corroborating the embedded data collector results.INTRODUCTIONDynamic testing of driven pile foundations was originally developed in the late 1960’s and commercialized in the early 1970’s. While the methods of analyzing dynamic test data have improved with the advancement of computer technology, the test method and the sensors used to acquire the data have changed little. In 1998, under a research grant provided by the Florida Department of Transportation, (McVay et al, 2002) an Embedded Data Collector system (EDC) was developed. The collector utilizes two sensor packs, each consisting of one strain gage and one accelerometer, embedded near the pile toe and pile top. Utilizing the toe sensor pack, the system provides reliable real time pile end bearing capacity measurements. This end bearing capacity is combined with a Case Method Solution augmented with an automatic damping calculation to provide the overall pile capacity, pile skin friction capacity and pile end bearing capacity. Also, since the gages are embedded, they have the ability to track all changes from the casting yard (i.e. prestress), driving, and subsequent setup (freeze, relaxation, etc) at both the top and bottom of the pile."

Jan 1, 2017