Search Documents

By E. A. Lowe, A. F. Bellamy, J. W. Smith

"In the autumn of 1977 Bethlehem management initiated feasibility studies on recovery of by-product molybdenum from concentrate produced at the existing Highland Valley mining operation. Over the fall and winter months test work was carried forward concurrent with design, flowsheet, equipment specification and cost studies. The decision was made to go ahead with a 200 ton-per-day treatment plant. Construction started in early 1978 and progressed to an initial start-up stage in mid-June. Full operational status was reached in August 1978. Operational results through August 1979 are presented. INTRODUCTIONBethlehem Copper Corporation operates a 20,000 ton-per-day Open Pit Mine and Flotation Plant located in the Highland Valley, some 30 air miles Southwest of Kamloops and 20 miles Southeast of Ashcroft, B.C.Two open pits are worked; the Iona Pit with limited reserves of higher Mo content, and the lower grade, more extensive Jersey Pit. Upwards of 150 tons per day of bornite-chalcopyrite bulk concentrate is produced, ranging 0.25% to 1.5% in molybdenum grade depending on the area mined."

Jan 1, 1980

By P. G. Claridge, R. A. Tenbergen

"Pipe Open Pit ore is delivered by rail to the Thompson Mill at a rate of 34,000 tons per week. Ore is milled at a rate of 220 tons per hour.Characteristics of the serpentinised peridotite host rock are such that significant deviations from hitherto experienced milling practice became a necessity because of coagulation of the gangue upon cominution.Extensive development work was done in the grinding and classification circuits to better understand the ore characteristics and optimize operating parameters and the use of available equipment. This work ultimately resulted in the change from 30 to 20-inch diameter cyclones.Coagulation of the ore slurry and the characterstics of the sulfide minerals necessitated an ""unconventional approach"" in processing as compared with the beneficiation of Thompson Mine ore.Recent changes in ore characteristics led to testing of antistatic agents to reduce tailing losses."

Jan 1, 1975

By W. D. Haley

The report of the Forestry Committee, presented to the recent Imperial Conference at London, is discouraging in its view of the future of timber resources and supplies. From a review of the forestry situation throughout the world, there is every likelihood that, thirty years from this, a shortage of the soft-woods will be severely felt. In the United States, only about one-third of the present forest area contains virgin timber. This will be cleared at the rate of five and a half million acres a year, so that in twenty-five years it will be about all gone. Canada has only about 27 per cent of her original forests left, and her virgin soft-wood will last but another half century. At the present time, the value of her lumber products is over $300,000,000 annually. During the summers of 1909 and 1910, the Government of Nova Scotia caused an examination to be made of the forest conditions in this Province. The reconnaissance, which was under the direction of Professor B. E. Fernow, of Toronto, involved an examination of the various soils, the rate of growth of the wood, and a general survey of the forest area. The importance to the Province of conserving its forest resources was clearly shown, and a number of recommendations were made, which; however, were never acted upon.

Jan 1, 1927

When underground extractions occur beneath or in close proximity to valleys and other forms of irregular surface topographic features, the observed vertical subsidence at the base of the valley is less than that would be expected in flat terrain, while the valley sides are observed to move inwards towards the centre of the valley. The reduction in subsidence at the bottom of the valley is referred to as upsidence and the convergence of two sides of the valley is termed valley closure. Research coupled with mining experience over the past few decades in Australia has identified valley closure subsidence as being very real and quite significant part of non-conventional subsidence effects, which always have adverse effects on natural features, with risks to water flow and aquatic ecosystems. In this paper, we describe a threedimensional numerical modelling approach to investigate the geomechanical mechanisms which cause the valley closure subsidence behaviour, using distinct element computer package 3DEC. The calibrated models can accurately predict subsidence and horizontal displacements, and they are subsequently extended to specifically study the effect of a series of mining geological and topographical factors on valley closure subsidence phenomenon, by developing a range of hypothetical scenarios. Previous analyses carried out using a two-dimensional numerical modelling technique have identified the potential parameters that affect the valley closure subsidence, which mainly include longwall position, horizontal stresses, valley sloping angle, and valley shape. Further three-dimensional analyses regarding the relationships between the major factors and valley closure subsidence are discussed in this paper. The results have significant implications with regard to both the underlying mechanisms that lead to this nonconventional subsidence behaviour, and how these should be incorporated in future valley closure subsidence prediction and mitigation of its impacts on natural features.

Jan 1, 2015

By Carol J. Odell

As a mining social practitioner, social indicators are within the purview of required competencies. A situation, where the ER manager requested assistance in quickly deriving a few social indicators for the strategic plan motivates this paper: despite ample technical knowledge about indicators, a clear understanding of stakeholder aspirations and concerns, as well as familiarity with management priorities such a request required reflection to produce a satisfactory approach, which combined pragmatism with enough academic rigour to provide reliable measures, while being justifiable to management who are unfamiliar with many of the pertinent debates. Importance: Social indicators enable the identification of more and less effective mine-community engagement strategies as well as providing primary data to better understand how the mine-community social system responds to different interventions, thus guiding future engagement plans. In addition social indicators: ? Assist communication about social strategies with Engineering and Operations management, using a quantitative language that is familiar to them. ? Provides concrete data to engage stakeholders to discuss progress and challenges arising, to move discussions towards technically robust strategies and away from politically interested proposals. ? Finally, social measurement is required more and more in due diligence, covenants and ongoing monitoring in Independent Engineering assessments of projects for financing. This paper begins by considering some technical considerations that are useful to guide indicator development. It then introduces the field research informing this paper and discusses some useful results in the light of further applicable concepts from the literature. The paper ends by considering corporate aims in applying corporate social responsibility (CSR) programs and discusses the application of the research for practitioners at mining operations, in the light of these aims.

May 1, 2010

By Bruce Jago, Joe Zhou, Chris Martin

"From the perspective of metallurgical processing, gold ores can be classified into free-milling and refractory ores. Their extractive metallurgy are largely driven by mineralogical factors such as: gold particle size, association with other minerals, coatings and rimmings, presence of cyanicides, oxygen consumers and preg-robbers, presence of refractory gold minerals and locking of submicroscopic gold in sulfide mineral structure etc. Gold process mineralogy helps address issues and problems related to gold ore processing. It provides useful information on process selection, flowsheet development, recovery improvement and reagent consumption optimization. By combining classic mineralogical techniques, modern instrumental analysis and diagnostic metallurgy, the mineralogist is able to balance the various types of gold occurrence in an ore. This paper will provide a broad review of gold process mineralogy and the techniques available, and use case studies to describe how they can be used together, to provide the complete picture of gold process mineralogy in an ore. Examples will be used where applicable.INTRODUCTIONSince the early 1980’s, a great deal of work has been done in the characterization of gold ores, particularly refractory ores (Gasparrini, 1983; Wang, 1984; Hausen, 1985; Haines, 1986; Henley, 1989; Chryssoulis et al., 1990; Wang et al., 1992, 1994; Kojonen, 1999; Simon et al., 1999; Hong et al., 2000; Pals et al, 2003). Process mineralogy has come into its own as a respected inter-discipline in the fields of mineralogy and metallurgy – a subject that occupies an important place in both research and industry. As the free-milling gold ores are being depleted and more refractory ores are being discovered and processed, gold process mineralogy receives more and more attention from both the mineralogist and metallurgist as it helps to solve various problems encountered during gold ore processing. Steadily rising gold prices are also stimulating the need for gold process mineralogy due to the increasing demand for and production of the yellow metal. At SGS Lakefield Research, gold process mineralogy studies are conducted routinely on all types of gold ores and mill products to assist in a wide variety of metallurgical projects. This paper will briefly discuss the gold ore types and gold mineralogy, review the common mineralogical factors affecting gold extractive metallurgy and the techniques available to gold process mineralogy, introduce the procedure employed at SGS Lakefield Researc"

Jan 1, 2004

By K. L. C. Gonçalves, V. K. Alves

"CVRD’s Department of Development and Technology – GETEK has been developing and perfecting a general methodology for scaling up flotation and grinding circuits over several years. This methodology has been applied in several prospective CVRD mining projects. It encompasses a procedure for variability analysis based on bench scale tests, pilot scale grinding and flotation tests and modeling and simulation for scaling up the industrial flowsheet.The bench scale tests include the determination of the Work Index, simplified DWT tests, rougher flotation and locked-cycle tests with samples that are representative of the ore body variability. After completion of these studies, continuous, pilot-scale flotation tests are carried out at a Mini Pilot Plant with drill core samples representative of different stages of the mine life. Finally, studies are carried out with large volume samples using a conventional grinding and flotation pilot plant. This sample is also used for liberation characterization, grinding kinetics, flotation kinetics and industrial circuit scale up. This methodology has been successfully employed in the development of CVRD’s new mining projectINTRODUCTIONCVRD has been developing and perfecting a general methodology for scaling up flotation and grinding circuits over several years. The definition of the processing route and the sizing and scale up of the processing system are some of the products generated during the pre-feasibility of a greenfield project. This paper is focused on the scale up of grinding and flotation circuits, operations known to be of the most importance in a mineral processing plant.The methodology for the definition of the flotation and grinding circuits is divided in the following stages: bench scale ore variability studies, pilot plant operation and modeling followed by simulation. The product of this work is a calibrated simulator that can be utilized for plant operation as well as mine planning, looking to achieve optimal operational conditions.The current models used for scale up of the grinding circuits are aimed at the generating information about the size distribution of the circuit product. However, it is well known that the liberation state of these products may be of critical importance for the performance of the concentration processes downstream. Nevertheless, CVRD has been developing a methodology for liberation kinetics during grinding, aimed at optimizing grinding circuit throughput together with downstream flotation recovery."

Jan 1, 2006

By R. J. Munday

Although uranium deposits in northern Saskatchewan are clustered around the Athabasca basin, basement lithostructure determines their distribution. Basal Wollaston Group pelites are invariably graphitic and carry uraninite in felsic segregations and biotitic pegmatite. Where these intersect the Athabasca Formation, remobilized uranium concentrated as pitchblende. Uranium is also concentrated in silicified and hematized sandstone where the Athabasca Formation overlies post-orogenic faults. Presumably, pregnant solutions associated with the fault were stripped of their metals as they emerged into the contrasting physico-chemical environment of the sandstone basin. Both these types of mineralization correlate with a Grenvillian (-1,000 m.y.) heating event and associated diabase intrusions. However, the rich pitchblende veins at Uranium City appear to predate the Athabasca Formation, but display spatial correlation with the Martin Formation. They are tentatively associated with a syn- to post-D3 retrograde metamorphic event which thoroughly leached crystalline basement and generated uraniferous fluids which escaped, and precipitated metals, into fractures associated with faults that define the grabens in which the Martin Formation was deposited. Remobilization events allowed some of this uranium to move upward into fractures within Martin sediments.

Jan 1, 1979

By Ian R. Muirhead

Over the past year or so, a number of mining companies have been meeting to examine the role of research in surface mining and, in particular, how to establish a collaborative research effort for the surface mining industry. A review has been completed which has identified the topics that are of interest to the surface mining companies for undertaking collaborative research. This has identified key subject areas such as Operations & Equipment; Maintenance; Environment & Reclamation; and Stability. Specific research projects for the initial research effort have been selected which include Wireless Data Communications, Analysis and Management; Application of GPS in Mining; and Tires for Heavy Haulers. In addition, attention has also been focussed on finding a suitable low cost, but effective, organization to coordinate and manage the collaborative research. The recently formed CONRAD Organization (Canadian Oilsands Network for Research and Development) appears to be a suitable candidate and discussions are ongoing with that group. This paper provides a summary of the review of surface mining research needs and of the status of the establishment of a collaborative research body for surface mining.

Jan 1, 1996

By Simon W. Houlding

The mining community is geographically remote and widely dispersed. There is a growing requirement for formalized professional development of members by professional associations, and increasing recognition of the advantages of continuing education and training by both individuals and corporations. Working against these trends are the increasing expense and time commitments required for attendance at conventional courses and workshops. The result is a perceived need for a readily accessible source of continuing education and technical reference on the Internet. The design constraints for an Internet model for professional development include: ? browser compatibility, with any time, any place, any pace accessibility; ? a content presentation model with low bandwidth requirements, appropriate interactivity for examples, tools and reviews, and viewer performance monitoring capabilities; ? formal accreditation of content, presentation and process so that viewer achievements may be formalized in terms of widely recognized Continuing Education Units; ? availability of tools for conversion of source material to the presentation format with minimal effort. A model that meets the design constraints is presented and illustrated by examples from an existing Internet site for continuing education in mining.

May 1, 2002

By M. Vallée

"RÉSUMÉDurant les 10 dernières années, les améliorations dans le contrôle des limites des sautages et les arpentages après l’exploitation ont fourni des informations préalables et post facto sur les limites minières réalisées par rapport à la planification, plus particulièrement pour les grands chantiers exploités par les méthodes chambres vides et sous-niveaux. Cependant, peu de recherches ont été faites pour améliorer la délimitation du minerai, l’estimation des ressources et des réserves, les études de faisabilité et la récupération minière dans d’autres types de gisements. Il faudra d’abord expliciter les impacts des lacunes, en quantité et en qualité, de l’information géologique et de l’échantillonnage sur le rendement de l’extraction. Il faudra également remplacer la notion de « dilution générale » par celles de « dilution » et de « perte de minerai ». Les impacts des lacunes observées sur l’exploitation des gisements d’or filoniens sont démontrés par une simulation basée sur des résultats d’études antérieures à la mine Thompson d’Inco, des impacts financiers de densités d’information moindre et par des analyses des valeurs actualisées nettes (VAN) de deux cas types.Deux gisements similaires, de 3 m et 6 m de largeur et exploités par chambres vides sont étudiés, en prenant pour cas de base la délimitation sur maille de 7,5 m (25 pi.) et en étudiant les impacts des limites moins précises supportées par une maille de 15 m (50 pi.), en assumant que ces imprécisions moyennes de +/- 0,62 m se transforment soit en surestimation (dilution), soit en sous-estimation (pertes de minerai).Les impacts d’information moins précise ont été beaucoup plus forts sur le gisement plus étroit : autant la dilution que les pertes de métal ont diminué les VAN du gisement de 3 m de 39,27 % et 45,41 % respectivement, tandis que les VAN du gisement de 6 m ont été diminuées que de 12,84 % et 11,55 %.Ces impacts des valeurs actualisées nettes diminuées justifient et exigent des efforts plus systématiques pour s’assurer que les travaux de mise en valeur et les études de faisabilité soient réalisés de façon requise pour optimiser l’exploitation et offrir aux investisseurs des rendements compétitifs par rapport à ceux des autres secteurs industriels. ABSTRACTDuring the past 10 years, research work to improve the survey of stope limits after mining supplied useful information, particularly for large open and sub-level stopes, regarding waste dilution caused by differences between final production limits and planned stope limits.However, the efficiency of this information to improve the overall efficiency of the mining process is limited, given that the impacts of inaccurate ore limits leading to dilution (sensu stricto) and ore losses have not been considered adequately. Geological/sampling information should be optimized in terms of quantity and/or quality for the deposit characteristics and the constraints of the mining method used. As industry practice regarding the definition and recording of dilution is flexible and as ore losses frequently are poorly documented, the use of these terms is reviewed.Simulations were carried out on two typical narrow gold deposits, based on an earlier study at Inco’s Thompson mine regarding the impacts of wide to narrow delineation grids using recorded variations of vein geometry. Vertical to sub-vertical deposits of 3 m and 6 m widths mined by long-hole open stopes were considered. Deposits delineated by 7.5 m (25 ft) grids were taken as a base case and the impacts of less accurate limits in conjunction with long hole mining based only on a 15 m (50 ft) delineation grid. The impacts of overestimation (dilution) and underestimation (metal losses) were considered separately, using the average error of +/-0.62 m recorded in the Inco study.The impact of less accurate information was much stronger on the narrower deposit: both dilution and ore losses diminished the net present value of the 3 m wide deposit"

Jan 1, 2005

By Donald Leroux, Colin Hardie

"New or improved mathematical models of mineral processing machines are published almost on a monthly basis. Often, these models can be calibrated from bench-scale test results and programmed using spreadsheet software to simulate different designs and operating conditions in open-circuit configuration. However, since mineral processing plants frequently operate comminution, separation and/or extraction machines in closed-circuit configurations, open-circuit simulations often have limited applicability.The simulation of closed-circuit configurations necessitates the programming of an iterative loop to bring the circuit to equilibrium. This can be done by using spreadsheet software but often requires advanced programming skills. As an alternative, LIMN® software, which simplifies the programming of closed-circuit configurations within spreadsheets can be used. This software was specifically designed to turn a Microsoft EXCEL® spreadsheet into a closed-circuit modeling and simulation platform with minimal programming.During the past few years, the Mineral Processing Group at the Noranda Technology Centre, has used this software for numerous projects which include the simulation of multi-stage cyclone circuits, closed-circuit regrinding and locked-cycle flotation tests. Using these projects as examples, the flexibility and the easy to use nature of the LIMN® software is demonstrated.INTRODUCTIONMineral processing engineers routinely have to make predictions regarding comminution and separation processes. Predicting the appropriate dimensions of equipment and the process response to changes in operating mode are probably the most common situations that they face. In all cases these predictions are expected to be rapid and accurate.Predictions made by engineers are frequently based on mathematical models. Many first principles, empirical, semi-empirical, steady state and dynamic models of mineral processes can be found in the literature. In fact, new or improved mineral processing models are continuously being proposed and in spite of this variety, process engineers often have to either develop their own or tailor existing models to suit their particular needs."

Jan 1, 2003

By P. Brad Marchant

"To properly evaluate bioleaching as a commercial alternative for sulphide concentrate oxidation, to enhance cyanidation response, it was necessary to define and optimize critical operating variables outside of the laboratory under less than ideal conditions. A complete bioleach testing laboratory was installed at Equity Silver Mines to aid in pilot plant flowsheet development.A continuous pilot scale bioleach circuit was constructed to provide data for meaningful valuation of biotechnology on a plant scale. The important operating and design parameters for pilot plant testing are described. Plant scale feasibility and design considerations, to treat a refractory pyrite/arsenopyrite concentrate produced from flotation tailing, are discussed. 1.0 BACKGROUNDEquity Silver Mines Limited is located 37 km southeast of Houston in central British Columbia. A 70% owned subsidiary of Placer Development Limited, Equity is Canada's largest open pit silver producer. Ore reserves were estimated at 28 million tonnes grading 106 g Ag/t, 0.96 g Au/t, and 0.38% Cu from two pits, the Southern Tail and the Main Zone. Detailed geology and mineralogy has been described previously(1,2).The concentrator flowsheet consists of conventional crushing, grinding, flotation, and dewatering circuits processing 5 300 tonnes per day of new mill feed. The resultant Cu/Ag/Au concentrate is trucked to Prince Rupert for shipment to market. Mill tailing reports to a closed circuit pond from which mill process water is recycled. Details of the concentrator process have been reported( 2,3).Production in the Southern Tail pit, from July 1980 to March 1984, resulted in mill tailing averaging 0.9 g Au/t and slightly more than 20 g Ag/t. Historic data indicate that unrecovered gold is associated with arsenopyrite and silver losses with unliberated tetrahedrite or minor silve,, bearing sulphosalts. Main Zone mill tailing, which commenced production in March 1984, contains approximately 0.5 g Au/t which is probably associated by majority with silver bearing minerals and pyrite while silver losses, 30-40 g Ag/t, are associated with unliberated silver and antimony bearing minerals."

Jan 1, 1985

By Ben Bradshaw

Context ? Community engagement has become an increasingly significant and challenging part of mineral exploration and mine development; indeed, opposition from communities proximate to a proposed mine site has been known to derail technologically- and financially-sound projects. ? These cases suggest that mining firms need to better understand how to engage constructively with local communities in the pursuit of their claims. ? While a range of publications exist promoting various community engagement strategies, these recommendations, when viewed as a whole, are disjointed and largely untested in real development contexts. Aims of Presentation 1. Synthesize industry, NGO, government and academic publications focused on community engagement best practice in order to highlight those practices that are most commonly recommended. 2. Review the (Canadian) mining industry?s experience with some of these strategies based on existing case material in order to identify the extent to which commonly prescribed strategies are used and validated in practice.

May 1, 2010

By J. E. Williamson

Introduction 1. Factors on Which the Design of the Roaster Plant was Based The roasting operation at Lake Shore, it was realized from the outset, would be profitable only if costs and losses could be reduced to a low figure. It was absolutely imperative that the operation should be self roasting over the whole range of tonnages and sulphur grades which might obtain during the life of the mine. The roasting operation could not bear the cost in fuel and labour of even a partially fired roast. To meet this requirement, it was necessary to resort to additional insulation in the construction of the roaster and to provide a more flexible means of rabble cooling than the conventional water jacket (see p. 31). A second basic consideration was that of handling a wet, putty-like concentrate. The operating costs of a drier ruled out the possibility of drying the charge before feeding it to the roaster. Moreover, the dusting which would result from charging a dry product virtually all -40 micron (325 mesh) in size would seriously handicap the use of a dryer. Dust lubrication (p. 3S) due to the back-mixing action of the Edwards rabbles, and the use of a Sullivan slapper ( p. 27) on the concentrate filter, completely solved the problem of handling the roast feed. The third consideration was the reduction of dusting to a sufficiently low point that a Cottrell or other dust collecting system was unnecessary. The Edwards roaster when properly supervised, it is believed, can be operated to give the minimum possible dusting. At Lake Shore, the evidence has been that less than 1 per cent dusting occurs at any time and that the greater part of the dust produced is recovered either in the spray tower or in the dust chambers.

Jan 1, 1947

By Alan D. Curtis

A standard planning block model for Phelps Dodge North America Operations has been developed to improve mine planning efficiency and performance in a skill starved environment. The model saves time on software management and training, consolidates data and standard information/output, enhances evaluation and strategic process, and improves communication between sites.

May 1, 2007

By W. Dingley, G. R. Hoey

"Thirteen Canadian sulphide ore mines were surveyed for corrosion control. The mines visited were a small, yet representative, proportion of this segment of the Canadian mining and metallurgical industry. Information on metallic corrosion and methods used to control it in underground workings and mills was gathered (a) by discussing corrosion problems with company personnel, (b) by examining equipment and structures during under-ground and mill tours, (c) by photographing corrosion sites, and (d) by collecting and analyzing mine water samples.The corrosion survey, which is summarized in the re-port, leads to the following general conclusions. Mine environments are corrosive, particularly when the mine w1a-ter is acidic. Because of a lack of good corrosion control measures, excessive deterioration of equipment due to corrosion occurs in mines. Mill environments are also corrosive, but in some cases good preventive measures are being taken to effectively control corrosion losses.Ways to reduce corrosion losses in sulphide ore mines and mills are discussed. The main areas for more corrosion research and development are selection of materials of construction, protective coatings, cathodic protection, inhibitors, equipment design, and mining and milling practices."

Jan 1, 1971

By M. Melashvili

"The SART Process was introduced to the gold mining industry in the late 1990s and several commercial plants were built over the following 10 to 15 years. Most of these plants have operated well and enjoyed plant performance in line with expectations based on the underlying chemistry of the process. However, two of the plants have consistently suffered from high reagent consumption and poor product quality, which has motivated a re-examination of the process fundamentals in the hope of understanding the reasons for poor performance when it occurs, and developing mitigating strategies.This testwork along with a review of the relevant literature has demonstrated that the amount of sulphide added to the primary reactor, relative to the copper concentration, is the most critical parameter dictating plant performance, with pH and residence time important secondary factors. The primary product in the SART Process is synthetic chalcocite, Cu2S, and the stoichiometric requirement for sulphide addition is therefore 0.5 moles per mole of copper in solution. Testwork shows that when sulphide is added in excess of this amount (generally with the express purpose of lowering residual copper in solution) it not only fails in its intended purpose, but can have a negative impact on the settling and filtration characteristics of the copper sulphide product, as well as the final product quality. Moreover, these problems are exacerbated the higher the selected operating pH in the pH 3 to 5 range, and the longer the residence time of slurry in this pH range.Freshly precipitated copper sulphide compounds are known to be very fine and slimy, with poor settling and filtration characteristics. It is therefore important to engineer the SART Process in such a way as to encourage growth in the average particle size of the precipitate crystals. This was the rationale for recycling a portion of the thickener underflow to the primary reactor when the SART Process was developed. The theory of crystallization predicts that compounds of extremely low solubility, such as chalcocite (Cu2S: KSP = 10-48), are likely to experience growth in crystal particle size through aggregation rather than heterogeneous nucleation. On this basis, the SART practice of recycling a portion of thickener underflow to the primary reactor in the commercial plants is unlikely to lead to crystal growth via nucleation, and could in fact promote breakage of the aggregates that formed in the thickener. Recycling thickener underflow could therefore have the opposite of the desired outcome. The result of testwork that is reported here lends credence to this theory and questions the wisdom of recycling in the SART process.There is evidence to suggest that operating the copper sulphide thickener in the SART Process without flocculants may be beneficial. Thickener underflow densities could improve from the current 10 - 15% range to 40 - 50%. This will not only reduce the flowrate of slurry to the filter, but the filtration properties of the slurry (filtration rate, filter cake moisture content) will also improve. This is one of the most critical engineering and design aspects of the SART Process, and the achievement of high solids density in the thickener underflow will not only improve the health and safety aspects of the operation, but also has the potential to lower capital costs and improve the quality of the final product."

Jan 1, 2016

By C. -K. Fang

"Aging effect on the wear resistance of alumina particulate-reinforced 6061 aluminum matrix composites with a block-on-ring wear tester has been investigated. Specimens with various Al2O3 volume fractions of 0%, 10% and 20% were employed in this work. Experimental results indicated that over-aged monolithic 6061 Al had the best wear resistance, as compared with under-aged and peak-aged conditions. For the composite containing 10% Al2O3, over-aging and peak-aging resulted in similar wear resistance, which was higher than that for underaging conditions. For the composite containing a high volume fraction (20%) of Al2O3, the wear resistance reduced with the increase in aging time. Although longer aging time was favourable to the wear resistance of monolithic 6061 Al, it was detrimental to that for the Al2O3/6061 Al composite with high volume fraction of particles. IntroductionMetal-matrix composites (MMCs) have received attention in many engineering applications because of the demands for high specific strength (strength-to-weight ratio) and specific stiffness, good high temperature capabilities and wear resistance. The manufacturing processes of fiber-, whisker-, and particulate-reinforced MMCs have been well developed (Hosking et al., 1982). Because of the reduction in fabrication cost, the applications of MMCs have been widely extended to light weight-bearing sleeves, calipers, automobile parts (brake rotors, drive shafts, connecting rods, piston rings, and cylinder liners), sporting goods, aerospace components, tanks (wheels, speed brakes, and track shoes) and other industrial applications. Among the three types of metal matrix composites, particulate-reinforced MMCs are promising because of their homogeneous and isotropic material properties and low cost. Additionally, they can be formed using conventional metal processing techniques."

Jan 1, 2003

By André van Wageningen

Long-term mine scheduling is one of the most difficult optimization problems. The problem is said to be NP-complete in that the best possible solution cannot be found any quicker than checking all possible permutations and combinations. Although a number of techniques have been used in the past, many include significant simplifications or fail to produce acceptable results within the required timeframe. Genetic Algorithms (GAs) are among the most promising optimisation techniques within operations research. They are based on natural selection and evolution of solutions to complex problems. They have been known to quickly converge within a few percent of the optimal solution by examining only a fraction of the solution search space. The GA itself contains very little problem specific information and as such, has been linked to a discrete-event simulation (DES). The DES feeds information regarding the feasibility and quality of the solutions back to the GA during the optimisation process. In this paper, GAs and DES are described and the coupling of the two methods is outlined. The GA coupled DES is then used to ?optimise? a problem and the results are discussed.

May 1, 2004