Search Documents

"In many gold deposits, a reasonable amount of the gold that remains in the cyanide leach tailing is associated with pyrite. Some gold plants have found it economical to incorporate gravity circuits on the cyanide leach tailing to recover the gold bearing pyrite before subjecting it to fine grinding, then recycling the ground pyrite back to the cyanide leach circuit. For low grade gold deposits the loss of gold bearing pyrite is exacerbated as the broader process economics normally favour a coarse grind (> 150 ?m). An option that has received attention over the last decade is to recover the gold bearing sulphides in the milling circuit by gravity, similar to the widely-practiced gravity recovery of free liberated gold. The modelling and simulation of a gravity gold circuit in a milling flowsheet is relatively simple compared with a gold bearing pyrite circuit, as the recycle advantages and breakage functions for gold and pyrite are quite different. This current work represents an attempt to simulate the gravity recovery of gold bearing sulphides in a milling circuit that also incorporates fine grinding, using relatively simple simulation models. The simulation results are further explored with reference to the economics of this type of circuit.INTRODUCTION It is well known that gold is associated with pyrite in most sulphide gold deposits and that the amount of gold associated with pyrite will vary from deposit to deposit. Most of the gold associated with pyrite is liberated in the grinding circuit during the processing of a gold ore. However, some gold remains occluded in the pyrite and is lost in the final leach tailings. Little information is available in the literature on methods to enhance gold liberation from pyrite by specifically removing pyrite, either in the grinding circuit or from the final tailings stream, and grinding it finer. One of the earliest record of this approach is described by King (King, 1949) where pyrite present in Witwatersrand gold ores was recovered by circular jigs and Johnson barrels followed by fine grinding of the concentrate prior to cyanide leaching. Dominy et al., 1970, provides information on the use of Yuba jigs to recover pyrite from the discharge end of ball mills. Again, the jig concentrate was ground to a fine particle size before cyanide leaching to recover the liberated gold. Unfortunately, no information is provided in these articles on the additional gold recovery from implementing these circuits in a flowsheet. Martins et al., 1993, provides details of a gravity circuit using Reichert cones and spirals to recover gold bearing pyrite from a cyanide leach tailings followed by fine grinding of the pyrite concentrate in a Tower mill. The ground concentrate returned to the front end of the already installed leach circuit. Overall recoveries were increased by some 2% to 4% depending on the amount of gold and pyrite in the plant feed."

Jan 1, 2017

By Kjell Winther

"Hydralift Scanmec introduced early in the eighties a new and different mill design for very large grinding mills. The design described has actually no size limitation upwards and is so far suggested with motor power up to 40 MW. The mill is furnished with gearless ring motor drive transmission. It is totally fabricated, without heavy castings. The first installation, an 8, 1 MW ball mill dia. 6,5 m x 9,65 m length, has been in continous operation in 13 years without problems. Total grinding costs has been reduced with 3 0% compared to traditional smaller mills. Reductions has been achieved in maintenance cost, power consumption, liner wear and grinding media consumption.So far 3 ball mills of the described design are delivered and in operation, one grinding Iron ore and two grinding Nickel ore.IntroductionThe design of mills for mineral ore dressing has basically been unchanged since grinding in mills started some I 00 years ago, in spite of the fact that mills have grown larger and larger. This has resulted in structural and mechanical problems, causing expensive failures and loss of production.Hydralift Scanmec engineers were designing mills for more than 20 years according to the old «rules». As they experienced interest for an increase in the mill size at the time when reports about failing mills were published, they started analyzing the different mill parts to find new solutions. One goal was to only use elements from proven technology in the new design. Two key items were ring motor (wrap around motor)(Isch et al. 1977, Meintrup and Klein 1982, Ranze 1983) and large diameter pad bearings (wrap around bearings)(Fuller 1984), both acknowledged from other industries."

Jan 1, 1995

By J. R. Goode

"The Las Cristinas deposit contains about 10.2 million ounces of gold at a grade of 1.3 g/t. The deposit comprises a layer of fully oxidized saprolite (SAPO), a layer of sulphide-enriched saprolite (SAPS), carbonate leached bedrock (CLB) and carbonate stable or un-leached bedrock (CSB). Gold occurs at about the same level in all lithological groups. The bedrock units contain minor amounts of copper (about 0.1%) as chalcopyrite, while SAPO contains virtually no copper it having been leached and deposited in the SAPS zone.A previous owner started investigation of the Las Cristinas deposit in Venezuela in 1991. Over the next seven years, 1174 holes with a total length of 159 km were drilled, extensive metallurgical testwork, including pilot plant operations, were conducted and feasibility studies were completed. Construction was started in 1997 and again in 1999 but was suspended.Crystallex has been producing gold in Venezuela since the early 1990’s. In 1997, Crystallex acquired Inversora Mael which had held two of the claims to the Las Cristinas concessions since 1986. In September 2002, Crystallex entered into a definitive agreement with the Corporación Venezolana de Guayana, (CVG), to develop the Las Cristinas deposit.An extensive program of studies and testwork was started in early 2003 to determine an optimum development plan for Las Cristinas. Mine Development Associates, SNC–Lavalin Engineers and Constructors, SGS Lakefield Research Limited, J.R. Goode and Associates, and Professor A. Laplante at McGill University acted as the main contractors.Because of the potential value of by-product copper, earlier flowsheets used carbon-in-leach for SAPO, but processed all other ore types by flotation to produce a gold-copper concentrate with cyanide leaching of cleaner tailings to maximize gold recovery. Cyanide recovery was necessitated by the high copper content of the leach feed. Initial studies of available data by Crystallex revealed that direct leaching of all ore types would provide about 11% more gold recovery than the previously selected flotation route with reduced capital and operating costs.Bench and pilot scale studies have confirmed that a SAG-ball mill-gravity-CIL route is very effective for all ore types and will give about 89% gold recovery. This paper describes the recent testwork, discusses the proposed plant design, and presents economic data."

Jan 1, 2004

By L. C. Lien

Tower crane layout (TCL) is a typical construction site layout (CSL) problem, which is suitable for a wide range of work assignments and site conditions. Tower crane is one of the key facilities for vertical and horizontal transportation of materials, especially for heavy prefabrication units such as steel beams, ready mixed concrete, prefabricated elements and large panel formwork such as machinery and equipment, and a wide variety of other building materials within a construction site. However, it is a difficult combinatorial optimization problem to determine the locations of tower cranes with materials quantity supply and demand for engineers. Swarm intelligence (SI) was very popular and widely used in many complex optimization problems which was collective behaviour of social systems such as honey bees (bee algorithm, BA) and birds (particle swarm optimization, PSO). This study applied a hybrid swarm algorithm namely particle bee algorithm (PBA) based on a particular intelligent behaviour of honey bee and bird swarms by integrates theirs advantages. This study compares the performance of PBA with BA and PSO for a proposed hypothetical construction engineering of TCL with materials quantity supply and demand problem. Results show that PBA performs better performance than the mentioned algorithms on a proposed hypothetical TCL problem.

Aug 1, 2013

By Nick D. Rose

The Dy deposit is a 21 Mt Pb-Zn-Ag-Au SEDEX-type massive sulphide resource located in the Anvil District, Faro, Yukon. This relatively unexplored orebody lies at a depth of 480 to 920m below surface, dips 20 to 35o and comprises vertical ore thicknesses of 3 to 28m at a 9% Pb + Zn cut-off grade. The deposit has been tested at depth with 63 surface diamond drillholes, but has not yet been explored or developed by underground means. Over the past decade, pre-feasibility investigations were conducted for two separate owners of the property to determine the economic viability of developing an underground mine at Dy. Following these previous studies an assessment was undertaken between 1998 and 2000 to further investigate geotechnical considerations for underground mining. The results and conclusions drawn from this study provide direction for possible future exploration at Dy.

May 1, 2002

By Alex Matheson, Nick W. D. Massey, Peter T. Bobrowsky

Crowing pressures on aggregate resources include diminishing reserves, high transportation costs, sterilization and land use conflicts. In the absence of detailed resource knowledge for a particular region, aggregate resource potential maps provide the best "first approximation" regarding the surficial distribution of sand and gravel. The 1:50 000 scale Level Ill aggregate potential map integrates several important factors which influence the management of sand and gravel. Data used to generate this type of thematic map is readily available in most areas, fieldwork required is minimal, there is a logical quantitative evaluation of the data layers and integration is easily accomplished on a desktop PC-based platform. Also the aggregate potential map, with its focus on identifying areas of potential future aggregate exploitation as well as present inventory, provides a useful tool for the aggregate explorationist.

Jan 1, 2001

By Julian Wills

The Candrill was developed with Soredem as a one-operator rockdrill for Canadian narrow vein mining. It provides the benefits of increased drilling rates, lower noise and vibration, mass reduction of 20% and system cost saving. The Candrill is to be commercialised at the end of 2001 together with a stoper drill through Parts Headquarters, Novatek's Canadian agent. The Candrill or pneumatic drills may be further exploited using a simple mechanised drilling system to further reduce operator labour, improve drilling speeds by up to 50% and to enhance drilling accuracy. Novatek's drilling system for simple mechanisation in gold and platinum mines is integrated with roof supports, can operate in stope widths as low as 800 mm and has resulted in labour savings of 50%, improved advances per blast of 20 to 50% and improved operator safety and ergonomics.

Oct 1, 2001

By D. R. Pyke, R. S. Middleton

"Three main types of base metal sulphide mineralization are present in the Timmins area:(1) -Massive and stringer-type copper-zinc deposits occurring mainly in pyroclastic rocks, as typified by the mines of Kam-Kotia, Jameland and Canadian Jamieson, or within or close to possible breccia pipes as shown by the Genex and Kidd Creek mines. With the exception of the Kidd Creek mine, all of these orebodies occur northwest of Timmins (Kamiskotia area) and appear to lie within or close to a major center of volcanic activity characterized by a thick accumulation of felsic pyroclastic rocks and subordinate epizonal intrusions. The margins of the rhyolitic pile are interfingered with mafic volcanics; overlying sedi-ments mark the termination of a vol-canic cycle. The copper-zinc deposits in the Kamiskotia area are confined to a particular stratigraphic unit. Ore-bearing solutions were probably derived from the intrusive complex of the volcanic pile.(2) -Porphyry copper deposit of the Mcintyre mine. The deposit occurs in a quarz porphyry intrusion related to the volcanism in the area (Hurst, 1936). Mineralization was probably introduced at the time of intrusion, and subsequently redistributed within the porphyry during deformation. (3) -Massive and disseminated nickel mineralization, associated with serpentinized alpine-type ultramafic intrusions, as shown by the Alexo, McWatters, Hart, Inco and Texmont deposits. The nickel mineralization occurs at or near contacts of the serpentinites with felsic or mafic volcanics, or sulphide-bearing iron formations. The nickel deposits south of Timmins are confined to a particular stratigraphic unit along the margins of domical-shaped structures which appear to outline former volcanic centers. Sulphurization as pro-posed by Naldrett (1966) appears to be a workable hypothesis for the formation of some of the deposits."

Jan 1, 1971

By Jean-Pierre Côté, Alexandre Noiseux

"Hatch and ArcelorMittal Mines Canada have combined their expertise to develop a dynamic model of the latter’s Iron Ore Pellet Plant in Quebec, Canada. This model was used to predict the benefits of different expansion projects, as well as asses the best implementation sequence.Two modelling tools were used: a discrete-event simulation software used to develop the dynamic model of the Pellet Plant and an in-house process simulator. The latter was based on operational data and known behavior of the process, and was calibrated with historical data gathered under different operating conditions.The results of the process simulator were used as input values for the dynamic model, which included all of the operation steps of the pelletizing process, from concentrate beneficiation to baking of the pellets. The model has been validated by assessing its capacity to represent adequately the operation of the plant during a 20-month operating period. It was able to reproduce the plant capacity within a precision of 1.2%.Simulated “what-if” scenarios allowed quantifying the production increase associated with the addition of new equipment such as ball mills or balling discs, implemented individually or in combination. Results revealed a potential 10% increase in the annual plant production by adding additional equipment in the two most limiting sectors of the plant, grinding and agglomeration. The simulation results made it possible to quantify the synergistic effect of two projects on plant throughput; the model showed that the combination of two projects resulted in a greater production increase than the sum of the same projects evaluated individually.Now that it has proven reliable, the simulation tool can readily be used by ArcelorMittal Mines Canada process engineers to perform simulations for equipment optimization, and to evaluate the impact of various operating parameters such as equipment availability and tonnage, product mix or concentrate quality. This work showed that a reliable model can be developed based on known parameters in combination with the proper integration of the process knowledge."

Jan 1, 2010

By Flavio Rojos-Tapia, Oscar Pereira-Cerda, Samuel Sánchez-Pino, Samuel Sánchez-Baquedano

"Pneumatic flotation was introduced to the Chilean Copper Mining Industry in 1993 by Ingeniería de Minerales S.A. (IDM). The technology is based on the designs of Dr. Rainer Imhof from Germany, who is the designer of several different types of pneumatic flotation cells, already sold through his Company Maelgwyn Mineral Service Limited (MMH). The company is represented by Ingenieria de Minerales S.A. (IDM) in South America.Pneumatic flotation, has been used in tough industrial applications .It has been successfully used for metallic ores such as copper sulphide and oxide minerals, copper slag, silica and silicates from iron magnetic preconcentrate (reverse flotation) and gold. It has also provided promising results when applied to molybdenum flotation. The latest applications, with ultrafine molybdenum particles in operating plants, is showing the V and G Cell (end model designed) as a real technological alternative to conventional flotation., The G Cell is an extremely high speed flotation machine with high selectivity which introduces the possibility of producing a final molybdenum concentrate with only one stage of cleaning. This is a completely new development in molybdenum flotation in the industrial circuit which has the potential to dramatically reduce the circulating load in the cleaning circuit. As a consequence the capital costs of future Molybdenum plants may also be reduced. The suitability of the G Cell will have to be determined on a case by case basis but it provides the metallurgist with an alternate flowsheet for consideration.The good performance of the G Cell can be explained by the high gas hold-up and very effective micro-turbulence which helps improve the attachment of solid particles to the bubbles. This technology may change our traditional concept of residence time in flotation. Additionally, the rotation phenomena introduced in the vessel of the G Cell ,creates radial separation forces which are critical to achieving a more rapid separation of the target minerals from the tailing. This results in a much reduced residence time requirement in the flotation machine. Some benefits associated with the use of the new G Cell are: less energy consumption, less maintenance costs, simple and reliable circuit to operate and a small area required for installing the circuits.As a result of the industrial experience in the Chile, the pneumatic flotation type G Cell can be regarded as a technology which must be considered as a replacement technology for the rougher and cleaner stages for fine particle flotation."

Jan 1, 2008

By R. H. Batey

"The process control and cost of monitoring mining slurries is normally accomplished using a continuous mass flow system, conventionally embodying a volumetric magnetic flow meter and nuclear density meter. DuPont’s Maxville Mine at Starke, Florida, USA was chosen to examine costs associated with performance of a nuclear density meter. Since it is typical of many mid-sized establishments and has a long history in their use. The published accuracy under ideal conditions of a nuclear density meter is ± 1.0%, but in practice considerable ambiguity of cost in annual production implies ± 2% at best. Using such accuracy in a 400mm (16”) pipe carrying zircon slurry at 75,000 tons/day, the cost of ambiguity, together with initial and running costs, amount to nominally $962,000 per year.Such cost leaves much to be desired. This paper describes an unique continuous, direct mass per unit volume Density Meter used for mining slurries in pipe sizes up to 1000mm (40”), which significantly reduces the cost of ambiguity of measurement and running costs. At the same time the disadvantages of nuclear devices are obviated.In an effort to reduce costs, a 400mm non-nuclear Density Meter was installed at the DuPont Maxville mine. A typical on-site accuracy can be shown to be ± 0.285%, whereby the cost of ambiguity, initial and running costs in the example above shows an annual improvement of $78,660, a reduction of over $880,000 per year.Even higher cost savings may be demonstrated with mass flow systems having gas entrainment compensation. Unlike nuclear and other inferential density meters, the signal quality of this non-nuclear Density Meter is totally unaffected by entrained gas found in mining slurries. This non-nuclear density meter is then ideally used with a vortex velocity domain sonic flow meter, and provides for the first time compensation in wet density or dry % solids, as well as wet or dry mass flow of mining slurries with entrained gas, resulting in enormous reductions in cost ambiguity."

Jan 1, 2013

By Alexandra Kozak, Rodrigo Costa, Bob Fukuhara

"The Jacobina project in Bahia, Brazil commenced operations in 2004 with a design capacity of 4,200 tpd. A project development plan to increase plant capacity to 6,500 tpd will be discussed. The project included an evaluation of the existing circuit and addressed bottlenecks in the crushing, milling, sedimentation, leaching and tailings transport. These circuits and the methodology used to provide higher capacity will be presented.INTRODUCTIONThe Jacobina mine is located in the state of Bahia in northeastern Brazil approximately 330 km northwest of the state capital city of Salvador and 9 km from the town of Jacobina. The Jacobina Mine (Figure 1) is owned by Jacobina Mineração e Comércio, a wholly owned subsidiary of Yamana Gold Inc.The gold mineralization of the Jacobina mine is hosted within quartz pebble conglomerate reefs of the Serra do Córrego Formation which together with the Rio do Ouro Formation forms the Serra do Jacobina mountain chain.The Serra do Jacobina mountains have been mined for gold since the late 17th century. Since the 1970’s, the Jacobina mine has been operated by Anglo American, Williams Resources Inc., Desert Sun Mining Inc. The mine is currently owned by Yamana Gold Inc.In December of 1998, operations at Jacobina were suspended and the property was placed under care and maintenance. Desert Sun Mining Inc. began exploring the property in 2002 and eventually purchased the Jacobina mine in 2003. In 2003, a feasibility study was completed that evaluated the economics of re-developing the mining operations and expanding gold production. In 2004, refurbishment and re-development of the mining operations began and the milling facility throughput capacity was expanded from 1.08 to 1.512 Mtpy (3,000 to 4,200 tpd). The milling operations were commissioned in the 1st quarter of 2005 and commercial production was declared 1 July 2005. In April 2006, Yamana Gold Inc. acquired the Jacobina mine through its acquisition of Desert Sun Mining Inc."

Jan 1, 2008

By J. Yue

"Mount Milligan mine is located in northern British Columbia. The concentrator employs conventional SABC grinding circuit with bulk sulphide flotation processes. Commissioning started in September of 2013 and nameplate production of 60,000 TPD was reached in the fourth quarter of 2015. As is typical with many mill ramp ups, bottlenecks developed as throughput increased. Since then, plant modifications and new control philosophies in the comminution and flotation circuits have been implemented and evaluated. The mine-to-mill collaboration played a key role in reaching target throughput rates by improving blast fragmentation and implementing temporary pre-crushing. Results of the projects as well as ongoing challenges/bottlenecks and solutions will be discussed.IntroductionMount Milligan Mine is a copper-gold producer located approximately 253 km northwest of Prince George in British Columbia. Production commenced in September 2013 and reached nameplate capacity of 60,000 TPD in December 2015. Average head grades for the mine life average 0.18% Cu and 0.39 g/t Au.Circuit DesignOriginal process design began with run-of-mine ore from the pit crushed through a 60-110 gyratory crusher, conveyed to a live ore stockpile and fed to the mill via four variable apron feeders. The concentrator circuit employs SAG mill - Ball mill - Pebble Crusher (SABC) grinding configuration to grind the ore down to a target P80 of ~200µm. It is then fed to two parallel trains of flotation tanks, each consisting of five 200 m3 tank cells with the first two being roughers and last three being scavengers. Concentrate streams from roughers and scavengers are separately reground with a closed circuit Tower mill and two open circuit ISA mills operating in parallel, respectively.Three stages of cleaners upgrade roughers/scavenger products to 25% Cu followed by a cleaner scavenger stage. The final concentrate is then thickened and filtered to approximately 9% moisture and shipped off site (Figure 1)."

Jan 1, 2017

By S. Banisi, M. Poorkani, M. Farzaneh, M. Askari

"At the Sarcheshmeh copper mine 40,000 t of ore per day with an average grade of 0.9 % Cu is ground to 70% passing 75 microns. Grinding is effected in 8 parallel lines of 8 x 5 m ball mills in a closed circuit with cyclones. The make-up balls are 80-mm forged alloy steel balls and the average ball consumption is 750 gh of ore ground. In order to optimize ball size distribution inside the mill, based on the previous investigation instead of using only 80 mm make-up balls a combination of 80 and 60 mm (75% to 25% by weight) ball charge was used in one of the mills. To evaluate the performance of three ball types namely forged alloy steel balls (A), ductile cast iron (C), high chromium cast iron (D) and also a combined (80 and 60 mm) charge of forged alloy steel balls (B), four identical parallel mills were charged accordingly. These four mills were sampled during a period of six months. The amount of material finer than 75 microns of cyclone overflows was selected as a criterion for the performance evaluation. It was observed that in a mill with the combined make-up balls the amount of fine produced was 4% higher than the other mills. The consumption of ball types A, C and D were 730, 710 and 534 g/t, respectively. The results of laboratory flotation tests showed that due to an improvement in the production of fines an increase of 1.4% in the overall copper recovery is obtainable. Due to the promising results, the new make-up ball regime was implemented in all mills in the plant.INTRODUCTIONThe Sarcheshmeh copper ore body which may rank as third or fourth largest in the world contains 1 billion tonnes averaging 0.90 % copper and 0.03 % molybdenum. It is located southeast of Iran and has been processing 40,000 t/d of ore since 1982. The mine produces 100,000 tonnes of copper and 2,200 tonnes of molybednite concentrate per year. After three stages of crushing, the ore with a F80 of 12.7 mm is fed to 8 parallel ball mills in closed circuit with cyclones to produce a product 70% finer than 75 microns. The concentrate of the first stage of flotation is reground and the tailing constitutes the main component of the plant final tailings. A concentrate with an average grade of 31% Cu is obtained after cleaning and re-cleaning stages. Total recovery of the plant varies between 83 and 87 % depending on the operating conditions and ore type."

Jan 1, 2002

By Linda Dufour

"Autoclaves have been in commercial use in the mining industry since the early 1950's the initial applications included tin, uranium, cobalt, nickel and copper extraction under both acidic and alkaline conditions. These circuits varied in batch or continuous operation. The geometry has been spherical, vertical, and horizontal type with up to six agitators, with throughput as high as 1000 stpd.Presently autoclaves are a good process selection for many refractory sulphide gold bearing ores. The first application of pressure oxidation in the gold industry was at the Homestake Mcglaughlin's Mine which was commissioned in 1985. This was an acidic pressure oxidation process treating 3000 stpd in three four compartment horizontal autoclaves 14' diameter and 53' long. Since the initiation of autoclaves for the treatment of gold bearing sulphides, there are presently 16 gold autoclaves operating worldwide varying in size up to 18'4"" inside diameter. There are seven autoclaves for the treatment of refractory sulphide gold bearing ores to be commissioned in 1997 and 1998.Autoclave technology has progressed extensively since the mid-eighties. Operational experience has made rapid progress and the result is much smoother and safer autoclave operation. There have been many advances in autoclave technology design. For example, the use of exotic materials for corrosion resistance to reduce down time for maintenance. The instrumentation involved in autoclave operation is very sophisticated which allows for many safety features. The advanced design has allowed for greater availability and as a result operating costs and maintenance costs have decreased. These technological advancements have made autoclave technology more safe and this has resulted in a greater acceptance of this type of operation. Many of the gold autoclave facilities operate up to 9 months continuously without shutdowns. The advancement of autoclave technology has inspired many new applications.Because of the outstanding operation of autoclaves in the gold industry, many other applications for autoclave technology are being considered. The following is a list of autoclave applications:"

Jan 1, 1997

By Heikki Laurila, Sirkka-Liisa Jämsä-Jounela, Jarkko Karesvuori

"Artificial Intelligence includes excellent tools for the control and supervision of industrial processes. Several thousand industrial applications have been reported worldwide. Recently, the designers of the A1 systems have begun to hybridize the intelligent techniques, expert systems, fuzzy logic and neural networks, to enhance the capability of the A1 systems. Expert systems have proved to be ideal candidates especially for the control of mineral processes.As successful case projects, an expert system based on on-line classification of the feed type using neural data analysis is described in this paper. The essential feature of this expert system is the classification of different feed types and their distinct control strategies at the plant. In addition to the classification, the expert system has a database containing information about how to handle the determined feed type. This self-leaming database scans historical process data to suggest the best treatment for the ore type under processing. The system has been tested in the Outokumpu Finnmines Oy, Hitura mine. Other projects have been reported to be in progress.INTRODUCTIONIn the past ten years considerable researches have been done in the application of artificial intelligent methods in process industry. The technologies of fuzzy logic, neural networks and expert systems have received several thousand applications worldwide: monitoring and analysis of process operations, fault diagnosis, supervisory control, feedback control and scheduling and planning of operations. Recently, the designers of these systems have begun to hybridize these intelligent techniques to enhance the current capability of expert system. Complex signal processing, neural networks, fuzzy logic and rule-based systems are also implemented to develop new so-called smart or intelligent sensors, actuators or components. Field buses are playing a more and more important role in automation systems and in imbedded systems. The development of field buses has allowed the distribution of smart components over networks."

Jan 1, 2000

By Hannu J. Häkkinen

Metal clusters exhibit unique size-dependent physical and chemical properties that differ from those of bulk materials or large particles. Here we discuss recent theoretical investigations of the catalytic properties of free and MgO-supported gold clusters. The catalytic activity of gold clusters depends sensitively on the environment, charge state, and chemical composition of the catalyst. Relativistic bonding effects stabilize large planar structures for gas-phase gold clusters, and non-compact ?quasiplanar? structures are present as important isomers also for surface-supported clusters. The hybridization of the atomic 5d and 6s states is significantly enhanced by the relativistic effects, and large spatial variations in the nature of the local electronic structure make the low-coordinated gold atoms preferable adsorption sites for oxygen molecules. The adsorbed oxygen molecules are activated to superoxo- and peroxo-states via charge-transfer from gold, and Eley-Rideal and Langmuir-Hinshelwood reactions with CO proceed via low-barrier formation of intermediates, which do not require O-O dissociation as precursors. This facilitates the low-temperature (below 300 K) activity of gold nanocatalysts in CO oxidation. Other gold nanostructures, such as mono-atomic gold nanowires, may also become important prototype systems in chemical sensing and nanocatalysis; here we show that they are active promoters of hydrogen dissociation.

Oct 1, 2003

By J. A. Meech, R. J. Tucker

"Since the establishment of froth flotation as an effective method of mineral beneficiation there has been both academic and industrial interest in the levels of the various reagents required to perform the desired separations. Academic interest was spurred by a desire to understand the mechanisms involved - industrial interest by a need to improve the efficiency of the process. These efficiency improvements can take two forms: cost reductions due to reduced reagent consumption and/or improved separation efficiencies. The latter are indicated by either improved grade-recovery relationships for removal of a valuable mineral from gangue, or improved separation of two similar valuable minerals.The processing of lower grade ore bodies at higher tonnage rates has necessitated increased interest in both reagent consumption and metal recovery. Furthermore, the development of accurate and functional on-stream analysis equipment in the 1960's and 1970's has allowed for a better understanding of the dynamic processes involved in a flotation circuit and has required a more concrete statement of the relationships and reactions between the minerals and chemicals in the flotation pulp. Development of these relationships is necessary in order to make use of on-stream analysis to control the process at, or near its more efficient level."

Jan 1, 1984

"Mineral separation by exploiting the differences in mineral or metal specific gravities (sg) has been used since antiquity. In the modern era, this is most commonly seen in the recovery of gold by the use of centrifugal concentrators and the separation of coal (low sg) from waste rock (high sg) using heavy media cyclones and jigs. Other metals, notably oxides of tin and tungsten, are successfully recovered using some combination of jigs, spirals and shaking tables. However, many conventional gravity separation systems are limited to fairly coarse (>1 mm) to medium (>100 micron) particle separations due to the limitations of the gravitational separation forces in conventional equipment.Many of the high specific gravity minerals of interest are friable (e.g. cassiterite, wolframite, etc.) and excessive fines are generated in the grinding/comminution circuits which cannot be recovered with conventional equipment and may be lost directly to the tailings stream. Recent developments in centrifugal gravity separation equipment specifically designed for fine or ultra-fine particle separation and recovery have resulted in heavy mineral particle recoveries as fine as 10-20 microns. Ongoing research work has also identified the benefit of closed-circuit, multi-stage gravity recovery circuits using some combination of centrifugal concentrators and conventional equipment (tables, spirals, flotation, etc.) which can substantially increase overall plant recovery and final concentrate grade.This paper will provide details of the evolution of non-fluidized bed gravity concentrators for high sg mineral recoveries, correlate laboratory scale development work with plant results to confirm scale-up, and show how recent flowsheet developments have contributed to significantly improved plant performance.IntroductionGravity concentration is one of the oldest and most cost effective metal and/or mineral recovery systems, ranging from the classic hand panning of alluvial gold, through to the large scale production of a wide range of metals and minerals, including gold, silver, PGMs, black sands, coal and iron oxides. Conventional gravity recovery systems, comprised of some combination of sluices, spirals, jigs and shaking tables have limited application in fine particle (i.e. <100 microns) recovery, or where there are limited differences in particle specific gravities (sg), e.g. the separation of high sg, high value metal oxides (e.g. those of tin, tantalum or tungsten), from medium sg, lower value metal sulfides such as pyrite and pyrrhotite. These unit operations tend to have limited capacity, and while double and triple turn spirals and multi-deck tables have been developed, extensive floor space is often required in order to process the tonnages incorporated in the modern mineral processing plant."

Jan 1, 2017

By J. B. Scott

"A computerized cost estimating program developed with the use of the Lotus 1-2-3 spreadsheet program has produced dramatic savings in preparing estimates for operating costs, equipment fleet size and manpower requirements for underground mines.The program is used by Dynatec to support its consulting engineering projects, particularly feasibility studies. The &apos;first principles&apos; approach is used to prepare detailed estimates under direct labour and supplies categories and maintenance costs for each mining operation . User notes have been developed to guide the estimator and ensure appropriate consideration is given to the specifics of the particular mine.A typical case history is illustrated and the ease by which alternatives and sensitivity analyses can be prepared is demonstrated. IntroductionHistorical MethodsMining engineers have used one or a combination of methods to prepare operating cost estimates for new or existing mine s. Operating companies have access to historical cost data and generally use this for preparing estimates. Consulting engineers do not usually have direct access to such information and must rely on mining companies (the present or previous clients); publications (text books, equipment manufacturers manuals, CMJ reference manual, etc.); annual reports (applicable to public companies); previous studies (to be used with caution as conditions change from mine to mine); and first principles (the subject of this paper), for cost information:Definition of First PrinciplesA first principles approach to cost estimating considers individual primary work elements of an operation. Quantities of work items are developed from the mine plans, production rates, geographic and physical layouts etc. The knowledgeable estimator, assisted by experienced operations personnel, can assign appropriate resources (equipment, labour, supplies and services) to each work element and establish productivities. Completion of the cost estimate is then largely arithmetic."

Jan 1, 1988