Search Documents

In-Situ Leaching (ISL) process plants are low cost producers for uranium deposits where the geology is suitable. In the 1970s, a three-year pilot ISL program occurred on gold ore from the Ajax Mine, Cripple Creek District, Colorado, using a chloride and iodide solution [1]. The test was halted due to poor results. With gold and silver the international ISL progress has been slow; however the potential for low capital expenditure (CAPEX) and operating expenditure (OPEX) with large low grade deposits is real. Unless the metallurgy has been demonstrated there are significant risks which could be fatal flaws to an ISL gold or silver project. The metallurgy of gold ISL projects is far from simple and it is early days with project development.

Jan 1, 2011

By E. G. Joe

"Recent trends in Canadian mineral processing were reported in seven areas of interest covered by seventeen technical papers at the 1976 Annual Meeting of the Canadian Mineral Processors, held at Energy, Mines and Resources' Camsell Hall, Ottawa. New milling equipment included the Enviro-Clear thickener, large-volume Outokumpu flotation machines and abrasion-resistant polyurethane screens. Grinding experiences from a variety of milling operations were reported. Opportunities for increased sizing and grinding efficiency were presented. Flotation control by digital computer and by chemical additions were described in two mill operations. Slurry pumping and sampling techniques were described for various operations. Environmental control in milling was reported concerning dust suppression, arsenic removal and tailings disposal. Several aspects of gold milling were described by the most recently commissioned gold mine and by CANMET. Potash operations were reported showing the similarity of processing and process control to that of metallic minerals."

Jan 1, 1976

By Rodrigo A. Marinho

Erratic high grade values are as common in Nature as they are a source of problems for resource estimators. In some highly erratic metal deposits, less than 2% of the drilling samples can represent more than 10% of the total metal in the blocks and they are associated with a high risk level. There is a risk of local overestimation but also of global overestimation, with the high grades being projected over too large a volume. Capping or restriction of these outliers control is being widely used in the industry and commonly applied in resource estimation for the last three decades. The primary purpose of this paper is to present and describe the most applied methodologies for restricting the extrapolation of high grade samples and discuss the results based on a theoretical simulated model. Additionally, this paper demonstrates the economical impact associated with the high-grade and the project risk profile associated with each method.

Oct 1, 2009

By H. Alzraiee

Traditional planning methods such as CPM and PERT have been useful tools to manage construction projects. However, the underlying model of these traditional methods often seems to fail to represent real projects as they tend to assume no interrelationship between project components. In reality, project components have complex dynamic feedback process that requires modeling of inherent uncertainty in the execution of these projects. Nevertheless, this dynamic nature and uncertainty have not been explicitly addressed by traditional planning methods. Project failure can be attributed to poor representation of the inner and outer aspects of operations that are responsible for project dynamics. Uncontrollable external forces are often cited but the real cause may be internal such as the feedback process among components of the project. An alternative perspective is offered in this paper through system dynamics (SD) that accounts for the feedback process and discrete event simulation (DES) for modeling the uncertainty. The proposed method utilizes SD method for modeling project dynamics and DES method coupled with CPM network for operational details and uncertainty, respectively. A case study that involves preparing engineering drawings in a design office is used to demonstrate the use of the developed method and to highlight its capabilities. Modeling the dynamic dimension is expected to enhance planning and scheduling of construction operations and to provide a better understanding of the impact of various internal and external factors on project schedule and productivity performance.

Aug 1, 2013

By W. Schubert, N. Radoncic

"The term “squeezing” is frequently used, although it is ill defined. Definitions like “large and long lasting displacements” raise the questions about the threshold values for the magnitude and duration of displacements. Large displacements during tunnelling frequently are observed in fault zones with high overburden. Whether this causes problems very much depends on the design approach used. On the one hand, the magnitude of expected displacements has to be predicted prior to excavation to provide for enough allowance for the displacements without violating the clearance profile. On the other hand, the support characteristics must be compatible with the expected imposed strains. As the magnitude of the displacements and thus the strains in the support depend on the support capacity and its characteristic (yielding potential), only well engineered systems will be successful.Experience in Alpine tunnels over the last decades has shown that closed shotcrete linings can sustain a strain of approximately 0.8% to 1% without failure. Any strain above this value inevitably leads to failure of the lining, and thus a loss of resistance, causing additional displacements. Based on a large number of simulations, a criterion for a critical overburden depth up to which closed linings can be used has been developed. Traditionally open gaps in the shotcrete linings have been used to allow for larger strains. To enhance the efficiency of the linings, yielding elements have been developed, which are integrated in the shotcrete lining, allowing large strains and controlled development of support resistance (Figure 2). When designing such yielding support systems, the development of the displacements, as well as the rheological behaviour of the supports must be considered. As the development of displacements to a large extent depends on the face advance, also the advance rate has to be considered, to be able to compare the time-dependent strength of the lining to the stresses developing as a result of the imposed strains. Another issue is the compatibility of the rock bolts with the large strains. With standard grouted bolts, there is a potential that the “fresh” grout is sheared due to the initially large strain rates. Special rib designs of the bolts allow for a higher strain tolerance.For successful tunnelling through fault zones quality monitoring and up-to-date data evaluation is of crucial importance. With advanced evaluation tools, changes in the ground conditions ahead of the face can be reliably predicted. With the help of empirical relations, the development of the displacements for different advance rates and supports can be predicted, allowing for the determination of the required overexcavation.The paper presents a review of the development of ductile elements, methods of analysis, and monitoring data interpretation."

Jan 1, 2015

By Y. Miyabayashi, K. Nishikawa, H. Nagai

JX Nippon Mining & Metals Group recovers valuable metals from end-of-life electronic products in an economical and environmentally-benign way, based on technologies that have been acquired in mining, smelting, and refining operations over time. End-of-life electronic products contain halogens and hydrocarbons. When such materials are treated in the copper smelting process, corrosion of equipment and discoloration of sulfuric acid occur. As a countermeasure to these problems, we have developed pretreatment processes that include an incinerator, exhaust gas washing towers, and a defluorination facility. By implementing these improvements, we have been able to treat a large volume of end-of-life electronic products efficiently in the copper smelting process.

Jan 1, 2014

By D. C. Fraser

"Geophysical Engineering and Surveys Limited of the Keevil Mining Group have routinely conducted ground surveys with VLF-EM receivers for the past two years. Both Crone's Radem and Ronka's EM16 have been used.VLF-EM dip-angle data often yield complex patterns which require considerable study for a proper interpretation. A method was developed which allows field operators to transform the noncontourable dip angles into contourable data, producing conductor patterns which are immediately apparent to exploration personnel untrained in VLF-EM interpretation.VLF-EM contoured data generally peak very close to the top of a conductor, thereby allowing drill holes to be spotted accurately. However, the data generally should not be used alone to select drill targets because structures may be sufficiently conductive to yield strong anomalies. Thus, magnetic and/or vertical-loop EM correlations may be considered as necessary criteria for drilling.VLF-EM surveys can replace IP surveys in certain environments. For example, the Restigouche orebody in the Bathurst camp of New Brunswick yielded a VLF-EM anomaly as distinct as that obtained by IP, although the body did not respond to vertical-or horizontal-loop EM. However, the cupriferous breccia pipes of the Triba mine near Batchawana, Ontario yield strong IP anomalies but not VLF-EM anomalies, illustrating that disseminated ore targets should be sought with IP rather than with VLF-EM."

Jan 1, 1971

By R. Saulters, M. Garshasb

The Transportable Moisture Limit (TML) is the copper concentrate moisture content beyond which liquefaction may occur during shipping. This study indicates that TML is a function of mineralogical characteristics of concentrate, which in turn may directly affect moisture retention properties. A comprehensive mineralogical and chemical analysis was conducted to determine the impact of composition and mineral content on concentrate’s TML. The analysis indicates that the high TML value is associated with particular minerals such as gypsum, swelling clay, muscovite and pyrite. Since higher TML values allow higher moisture contents for shipping, this property is desirable for concentrate inventory management and shipping flexibility. Scarcity of minerals that may increase TML contributes to limitations of shippable inventory. INTRODUCTION TML is the maximum moisture content of copper concentrate beyond which liquefaction may occur. Moisture content above the TML is considered a shipping hazard as it may result in loss of lives and cargo. The details of TML testing are given in ISO 12742:2007 (ISO 12742). In principle, TML is 90% of the Flow Moisture Point. The method of testing for Flow Moisture Point and TML is based on procedures that provide pulsations that simulate the cyclic force of ocean waves to determine moisture levels at which the onset of concentrate flow may occur. International Maritime Organization (IMO) provides guidelines for developing and approving TML testing and moisture determination in the context of its Moisture Management Plan (MMP) for shipment of copper concentrate cargoes (IMO 2013). The IMO regulations are specifically provided in MSC.1/Circ. 1454 “Guidelines for developing and approving procedures for sampling, testing and controlling the moisture content for solid bulk cargoes which may liquefy”. Since each port has its own operational characteristics, resource availability, peculiarities of governmental structure, and desired methods of interaction with the authorities, it is necessary to adopt the IMO guidelines to the local requirements. In order to establish a TML and MMP measurement system, it is required to implement and follow proper guidelines for the relevant procedures. For example, sampling procedures are developed in accordance of ISO 12743, “Copper, lead, zinc, and nickel concentrates – Sampling procedures for determination of metal and moisture content”. Moisture content of copper concentrate samples are determined in accordance with ISO 10251, “Copper, lead, zinc, and nickel concentrates – Determination of mass loss of bulk material on drying”. To assure strict adherence to the MMP procedures, the overall system needs to be integrated into the site QA/QC system, which would make them auditable and certified in accordance with standards such as ISO 9001, ISO 17025, and ISO 17020.

Jan 1, 2019

By R. Pérez, James A. Finch, F. Tavera, Cesar O. Gomez

"Gas holdup is a variable which affects the operation of flotation columns. On one hand, gas holdup is a function of bubble size (a function of sparger type, frother characteristics and concentration, and air flowrate), tailings flowrate, solids content, and mixing patterns in the collection zone. On the other, gas holdup defines flotation kinetics and carrying capacity. Therefore, gas holdup is a useful variable to control and diagnose the operation of a flotation column, but the lack of a reliable sensor for on-line gas holdup monitoring has prevented its use in industry.This work describes the principle and the practical difficulties associated with the development of a gas holdup sensor based on the measurement of the electrical conductivity of dispersions. Two different approaches have been devised. These approaches will be described and test results presented of prototypes in laboratory and industrial columns.Background.Several years ago, a research program was initiated at McGill to use electrical conductivity as the basis for developing sensors for process measurements in mineral processing. Electrical conductivity is an intensive property which is a function of the concentration of the different phases present in a dispersion. The initial focus was on the detection of the interface between two dispersions with different characteristics (i.e., that between the collection and froth zones in flotation columns or that between clear water and sedimented solids in thickeners). The technique works in this case by searching for the location at which a sudden change in specific conductivity occurs, as a consequence of different gas holdup or solids content, and absolute values of the specific conductivity of the dispersions involved are not necessary1,2."

Jan 1, 1995

By L. I. Kiss, S. Perron, S. Poncsák, A. Perron

Aluminium industry has an increasing interest in the diminution of the energy consumption of the Hall-Heroult process by the reduction of the anode bottom covering with gas. Electrically isolating carbon-dioxide bubbles, produced at the anode, increase the ohmic resistance of the cell. As the gas production rate is determined by the applied current density, anode covering can be decreased only by a faster evacuation of the gas from the inter-electrode space. Among others, the inclination and curvature of the anode bottom promotes the release of the bubbles and thus decreases the mean value of the covering. Indeed, anode, insert in the molten cryolite bath has a square shape with horizontal bottom. However, inhomogeneous anode consumption, electro-erosion, bath circulation and the inclination of the bath-metal interface modify this shape gradually during electrolysis. Anode bottoms become inclined with rounded comers. This concentrates the gas generation to the center zone of the anode. As the bubble layer cannot be observed directly because of the hostile environment and the opacity of the bath, real scale air-water systems are used to study the impact of the anode geometry on the anode covering and the bubble induced flow. However, the physical properties of such a system are different than that we can found in the real cells. A simulator using the Lagrangian description of the bubble layer has been built and presented in earlier papers. This tool was used to investigate the effect of the anode inclination on gas covering and bath velocity, for both C02-cryolite and air-water system. Results obtained for the second system were compared to experimental data .

Jan 1, 2006

By Z. Zhong, Y. J. Hu, D. Elsworth

"A standard triaxial apparatus was set up to perform sliding tests. Slide-hold-slide (SHS) tests, with hold times from 10 to 3000s and at invariant effective confining pressures of 1MPa, incremented to 3MPa and then 5MPa, were conducted on both dry and wet split limestone samples to study the evolution of fracture friction under holding and sliding processes. Limestone fracture shows time-dependent behaviors in SHS tests, friction drops (creep) gradually during hold periods, and recovers (healing) after re-slide. Frictional healing and creep increment are proportional with hold times, while are inversely proportional with effective confining pressures. Moreover, the wet sample displays heavier healing than the dry one, whereas creep increment of the wet sample is lighter than the dry one. We conclude that the evolution of limestone fracture friction is significantly controlled by mechanisms of fluid-rock interactions.INTRODUCTIONThe evolution of the mechanical properties of fractures and faults exerts a critical influence on the behavior of fault zones and on the earthquake cycle. In addition to natural processes, this behavior has broad implications in induced seismicity and influences oil and gas production, the sequestration of carbon dioxide and the disposal of nuclear wastes.Fault friction is typically measured by slide-hold-slide experiments, where fault gouge is deformed at low velocities (<0.1 mms-1) and over small shear offsets (<30 mm) (Dieterich, 1979, 1981; Mair et al., 1999; Marone, 1998, 2004) or alternatively with rotary-shear devices, that enable higher slip velocities over very large shear offsets (Hirose & Shimamoto, 2005; Mizoguchi et al., 2006). Typical experiments (Dieterich, 1972; Marone, 1998; Olsen et al., 1998; Bos & Spiers, 2002; Tenthorey et al., 2003) show significant creep during the holding period and frictional healing (strength gain) upon reloading. Fault creep and healing are often time-dependent with longer hold times typically resulting in greater magnitudes of creep and in strength gains (Tenthorey et al., 2003; Yasuhara et al., 2005; Carpenter et al., 2012). Frictional healing may arise from growth of grain contacts (potentially induced by pressure solution) (Rabinowicz, 1951; Dieterich & Kilgore, 1994; Yasuhara et al., 2005), strengthening of the contacts (correlates with cementation) (Hickman & Evans, 1992; Beeler et al., 1994; Karner et al., 1997; Olsen et al., 1998; Muhuri et al., 2003; Tenthorey et al., 2003; Li et al., 2011) or via other changes in state including changes in porosity and rearrangement of force chains. Experimental evidence (Dieterich, 1979, 1981; Johnson, 1981; Marone & Scholz, 1988; Marone, 1998; Saffer & Marone, 2003; Moore & Lockner, 2007; Ikari et al., 2007; Ikari et al., 2011; Carpenter et al., 2012) quantifies both the mode and magnitude of second-order changes in the velocity-dependent (including velocity- strengthening and weakening) evolution of frictional strength."

Jan 1, 2015

By David Morrison

Our present longwall problems in Cape Breton can be grouped under five main classifications. These are: (1) Roof control on the face and on the main roadways leading thereto. (2) Transportation of coal along face and levels. (3) Mechanical loading at the face. (4) Safe method of conducting and applying power at the working faces. (5) Dust nuisance. The usual layout for longwall operation in Cape Breton is to have three, and sometimes four, faces in line with each other, the length of face being from 400 feet to 500 feet (see Figure 1), and producing between 425 and 500 tons per face. Each wall is serviced by a well constructed roadway for transportation of coal, men, and materials, and is operated as an independent unit. Each wall works under a regular cycle of operations: first, cutting and boring; second, drawing hardwood chocks, building midwalls, and shifting panlines; and third, loading. The present method of roof control and operation of longwall faces has developed through trial and error since the commencement of longwall miring in Cape Breton. The basic method of roof control in all longwalls in Cape Breton is: rigid support of the roof in the immediate vicinity of the working faces by hardwood blocks, as shown in Figure 2, accompanied by a cushion support furnished by continuous midwalls, 12 feet wide, constructed of stone obtained from the waste and spaced at 50-foot centres. These midwalls are kept forward to within 4 feet to 10 feet of the working face and allow a gradual subsidence of overhead strata, thus preventing any sudden break at the working face.

Jan 1, 1947

By N. Giguère

Until recently, the heat treatment of pressure die cast parts has always been considered unpractical because the solution heat treatment resulted in unacceptable blistered parts. This was due to the presence of massive porosity associated with the die casting process where the inflow of metal inside the mold cavity is extremely turbulent. With the steady improvement of foundry practices and the generalization of vacuum die casting, porosity defects have been reduced to the point that a partial solutionizing heat treatment can be applied without any damage to the casting. However the solutionizing temperature must be lower than that applied to macroporosity free castings and for much shorter time. The object of the present study was to determine the optimum solutionizing temperature that can be applied to aluminum 383 die cast brackets along with the optimal temperature and time of aging resulting in the highest improvement in mechanical properties (both strength and ductility). This was done by testing strength and deformation on the casting itself using a specially designed jig; the crushing force to deformation curve was analyzed so as to quantify the improvement in both strength and ductility gained with the partial precipitation hardening heat treatment.

Jan 1, 2011

By H. J. Hartjens

"With the trend towards bringing into production ore bodies of lower and lower copper content every possible avenue of approach to achieve maximum copper metal recovery and keep milling costs to a minimum are of increasing importance.Equipment manufacturers have contributed a great deal by designing larger mills, flotation machines, pumps, etc. in lowering capital and operating costs; instrumentation and automation usually as a joint effort of operating staffs and equipment manufacturers have resulted in lower operating costs and improved metallurgy. Likewise manufacturers of chemicals used in mineral beneficiation have directed their research and development at new flotation reagents and treatment schemes to complement the needs for more efficient products, permitting coarser grinds without detriment to recovery, higher flotation rates, higher degrees of selectivity, as well as chemicals to improve settling, clarification and filtration. The various treatment schemes in use and suggested for consideration are:1) The choice of the flotation treatment scheme is largely dictated by the desire to operate a simple circuit, originally consisting of rougher and scavenger flotation, with scavenger concentrate either returning to the head of the rougher circuit or joining the rougher concentrate for cleaning by reflotation, with and without prior regrinding. The cleaner tailing was also recycled to the head of the rougher circuit. In the case of porphyry copper ores, this was originally the standard circuit. Lime is the preferred alkalinity regulator to adjust pH, usually in the range 10-12.To avoid the undesirable effects of circulating loads and gain the advantage of simplified control of the rougher circuit, open circuit cleaning is practiced more and more. In this scheme, cleaner tailing is scavenged to produce a discardable tailing and the scavenger concentrate returned either to the cleaner or the regrind circuit."

Jan 1, 1970

"High Pressure Grinding Roll (“HPGR”) technology is applied in a broadening range of minerals processing applications for relatively wet or moist materials. HPGR grinding of dry material or involving drying and air classification is more common, for example in cement manufacturing. A number of minerals processing plants are also operating with dry material, either due to process reasons, such as considerations of preceding or subsequent process stages, or as dictated by local conditions of arid areas and scarcity of water. The present world-wide expectation of decreasing availability of water supply urges us to look for alternatives that minimize water consumption.Recently established and envisaged future HPGR applications with dry ores have indicated that the technology of dry crushing and classification as practiced in cement and limestone grinding can be applied in minerals processing. Moreover, dry technology could very well be applied for generating a final fine product at sizes near or below 100 microns, as may be required for beneficiation by, for instance, flotation, magnetic separation or tank leaching.Dry HPGR grinding requires special attention in maintaining suitable process economics, when considering power input in grinding, drying and classification. In some cases, HPGR capacity and roll surface wear life may be negatively affected by a lack of moisture in the feed.This publication summarizes some of the features of, and experiences in dry HPGR applications. This includes design aspects of the classification system and discussion of the wear protection of the roll surfaces. The paper also includes examples of operational experiences of dry practices in minerals processing and cement plants."

Jan 1, 2012

By D. G. Cerigo

"INTRODUCTIONAn interim report covering an uncompleted project on revenue mill optimization was presented at the invitation of Mr. C.S. Stevens, the Secretary of the Canadian Gold Metallurgists. The work described summarizes the preliminary work carried out at the Noranda Research Centre on computer mill optimization and is an attempt to arrive at a model of a circuit using the ""black box"" approach and hence by using economic factors related to concentrate dollar value to maximize revenue. The help and cooperation of Mr. J.D. Wild, Mr. M.J.S. Bennett of Noranda and Dr. A. Bobkowicz of McGill University is gratefully acknowledged.DERIVATION OF MODELHistorical data from the Normetal mill were used for the study. Normetal ore contains chalcopyrite, sphalerite, gold, silver, pyrite and pyrrhotite. For simplicity, data were chosen for days when only two concentrates had been derived, a copper concentrate which also contains the gold and silver, and a zinc concentrate. In these periods when pyrite concentrate was not produced, its circuit was used as an extra zinc scavenger unit. Figure I is a schematic drawing of the circuit and Table I explains the nomenclature.The mill had been operated to obtain a fixed grade of copper and zinc in the copper and zinc concentrates respectively, at the same time insuring acceptable recovery levels. The target grade for the copper and zinc concentrates had been derived by manual calculations based on past experience. The data used were 170 sets of daily mill reports, a sample of which is shown in Table II. The data consist of daily tonnages of feed, concentrates and tailings and their average compositions obtained by taking samples every twenty minutes from each stream and analyzing the daily composite samples."

Jan 1, 1967

By J. Nsasi Bakambu

This paper describes an autonomous platform for exploration and navigation within networks of tunnels, as those typically found in underground mines and caves. In the exploration mode, a remotely located supervisor instructs the platform to move through successive sections of the network, gathering range data that is, then, concatenated into 2D/3D survey maps of the environment. In the navigation mode, the supervisor specifies high-level missions on the previously acquired survey maps. A motion planner, then, translates each mission into a set of consecutive navigation actions, separated by natural landmarks. Mission execution consists of detecting landmarks, self-localizing and performing the planned navigation actions.

May 1, 2003

By C. B. Webber, L. S. Diaz

"The paper presents the approach taken by Craigmont Mines to grinding circuit control. A detailed description is given of a fully automatic control system which bases its control actions on the continuous measurement of particle size in the cyclone overflow stream. The control system holds a specified particle size in the cyclone overflow, and grinds rod mi 11 ore feed at increased rates. The principles of operation of the system used for continuous measurement of particle size are described, end the improvements in mill throughput and copper recovery over several months of continuous operation are presented.INTRODUCTION Craigmont Mines Limited is located in the south-western interior region of the province of British Columbia, approximately 230 road miles north-east of Vancouver, and ten miles west of the town of Merritt. A moderate climate, good roads and service facilities provided by the Canadian Pacific Railway, Inland Natural Gas Company, and the B.C. Hydro and Power Authority, have provided a very favorable mine and plant site.The preliminary metallurgical design of the Craigmont mill was based on the test results of samples obtained from the original 2500' level drift during 1959. Pilot plant runs and other research testing for design pur¬poses were conducted at the Canadian Exploration Ltd. Laboratory, at Salmo, B.C. The design flowsheet was altered in progressive stages from 2,000 to 3,000, and finally 4,000 tons per day as the ore reserves became better defined. Construction work on the 2,400' level mill site commenced in late 1960. The official opening of Craigntnt Mines Limited took place on September 15, 1961, a little over two years from the time of the metallurgical assessment of the original ore samples.Mill throughput to date has varied widely both on a daily and a monthly basis, due to the varying hardness of the mine ores. The grindability af the ore appears to be related to the oxide iron content, which varies from lows of 9% to highs of 20%. Daily tonnage has ranged from 5,000 tons per day with 10% iron in the feed, to 6,000 tons per day with 20% iron feeds."

Jan 1, 1973

By Md. Rashedul Islam

Magnetic data was collected from the Yeoju historical sites using the fluxgate gradiometer through six sites & several grids. We measured the vertical gradient by the FM256 Fluxgate gradiometer. The readings were logged every half meter. The obtained data were processed and treated to introduce a high quality magnetic image. The gradiometer results defined various positive and negative magnetic anomalies, which revealed the existence of several archaeological features of different shapes and sizes. The study of the process magnetic images give us a concept that the subsurface features are caved shape stone chamber tombs, burial mounds, deep room structure, Yeoju mausoleum, pagoda?s square foundation stones, walls etc. All these are superior work of early Goguryeo inheriting orthodox Silla style. So, the study area may have great archeological interest.

May 1, 2009

By S. Banisi, A. R. Hasankhoei, Gh. Parsapour, A. R. Ghasemi

At the Gol-E-Gohar mining and industrial Company, a pelletizing plant, which includes two parallel dry closed grinding circuits and a pellet production circuit, produces 600 t/h. Each grinding circuit consists of a burner, a dry ball mill (6 m×13 m) and an air separator. Each ball mill consists of a 2 m-long dryer chamber and an 11 m-long grinding chamber. Iron ore concentrate is fed to the drying chamber to decrease its moisture from 2.5% to below 0.2%. The drying chamber consists of 56 flights in two rows. It was found when the feed moisture content decreased from 1.3 to 3.5%, the throughput decreased by 14% (40 t/h) indicating a low performance of the dryer. In order to improve the efficiency of the drying section, a scale down version of the dryer was constructed in a 1m diameter mill with a transparent end to make image analysis possible. It was found that because of the inappropriate veiling profile in the drying section, most of materials are not subjected to the hot gas tunnel. To overcome this problem, various flights with different geometries were physically tested and also simulated by the KMPCDEM © software. With the aim of arriving at a proper veiling profile which maximizes the particles contact with hot air, a new flight design was obtained and tested. The installation of the rectangular tooth type flights in one of the mills in the plant made the comparison of the old and new designs possible. The evaluation of the designs in a period of three months indicated 15 t/h increase in the throughput in the case of the new flight design.

Jan 1, 2016