Search Documents

By R. E. Lawless

The transportation challenge began with the need to move millions of tons of coal annually from Western Canada to Ontario. The paper will discuss the options which were available, the final mode selected and the economic trade-offs which were involved. It will outline the demands of unit train technology and the effect of transportation requirements on the other elements of the whole system.

Jan 1, 1979

By W. J. Li, L. Kong, G. L. Li, X. M. Xi, J. Qiu

"A novel hydrothermal method was applied to prepare the precursor of LiMn2O4 using pre-treated electrolytic manganese dioxide (EMD) and lithium hydroxide as the main raw materials. The precursor was subjected to heat treatment between 400 and 900ºC to obtain spinel Li1.05Mn1.95O4 and Li1.035Co0.035Mn1.930O4 positive materials for lithium ion batteries. The structure and morphology of the obtained powder materials were studied in detail by means of X-ray diffraction (XRD) and scanning electron microscope (SEM). It is found that the precursor has an amorphous structure and a high reactivity, which is easily transferred to spinel structure during heat treatment, obtaining a positive material with an uniform structure and good performances. The XRD patterns reveal that single phase spinel Li1.05Mn1.95O4 can be obtained from the precursor after heat treatment at 600°C in air. The final Li-rich Li1.05Mn1.95O4 product obtained showed a well-defined stable spinel structure and distinctive crystal faces with particle size between 200 and 300 nm. The as-prepared Co-doped spinel sample exhibited a excellent electrochemical performance with an initial discharge capacity of 113.0 mAh/g and 93.8% of its original value was retained after 100 charge-discharge cycling at 0.5 C.INTRODUCTIONThe increasing demand for portable electronic devices and hybrid or full electric vehicles is driving the development of cheap, efficient, compact lightweight and environmental friendly rechargeable batteries systems (Chung et al., 2002; Scrosati, 1995). Lithium ion secondary batteries have satisfied this demand to a greater degree than other battery systems. The cathode material plays a critical role in the performance of Li-ion batteries. The high cost and toxicity of cobalt compounds for the cathode material of LiCoO2 has prompted a search for alternative materials. LiMn2O4-based spinels offer a potentially attractive alternative to LiCoO2, due to its abundance, low price, ease of preparation, environmentally friendly characteristics, better thermal stability, and its effortless recycling (Tarascon et al., 1991; Yabuuchi and Ohzuku, 2003; Amatucci et al., 1999; Tsai et al., 2003). Some achievements have been created to meet the requirements (Guo et al., 2010; Kang et al., 2005; Park et al., 2008; Takahashi et al., 2006; Lee et al., 2001; Yoshio et al., 2001; Arumugam et al., 2008). However, the largest obstacle encountered in the practical applications of LiMn2O4 is its fast capacity fading during long term cycling, which is due to Jahn-Teller distortion of the [MnO6] framework, the electrolyte decomposition at high potentials and manganese dissolution into the electrolyte (Fey et al., 2003). The electrochemical performance of LiMn2O4 is also strongly dependent on its morphological properties, such as crystallinity, phase purity, surface area, grain shape and particle size distribution, etc. All these morphological properties are closely related to the material synthetic routines and heat treatment processes (Huang et al., 2000; Myung et al., 2000; Takada et al., 1998)."

Jan 1, 2012

By A. Zrimsek, G. Vingas, R. Wolke

IN 1952, prompted by the great demand of the Canadian drilling and foundry industries for sodium bentonite, the Geological Department of Magnet Cove Barium Corporation, Limited began an extensive search for bentonite deposits throughout western Canada. Their efforts were rewarded in 1958, when substantial deposits of high quality material were found approximately 100 miles southeast of Edmonton, Alberta. The bentonite material, a part of the Edmonton formation in the Upper Cretaceous, is located approximately nine miles south of the town of Rosalind. The land where the bentonite lies has in places .been eroded by stream and glacial action to form a wide gully, convenient for strip mining methods (see Figure 1). The bentonite bed is almost flat-lying, dipping to the southwest at approximately 12 feet per mile. The main bed is 8 to. 10 feet thick and is covered with 15 to 25 feet of overburden. Before stripping, the area is drilled and sampled to evaluate the quantity and quality of the bentonite.

Jan 1, 1962

By C. C. Li

The D bolt is a new type of energy-absorbing rock support element recently developed in Nor-way. The D bolt is not only able to accommodate large rock deformations, but can also provide a load-bearing capacity as high as that of rebar bolts. Furthermore, the anchoring quality of the D bolt is similar to rebar bolts because of its multi-point anchoring design.

May 1, 2009

By R. Roufail

"Energy consumption in stirred mills has been studied, in the last couple of decades, on a macro scale. Effective operation and meeting particle size required for downstream operations used to be the main objectives behind energy utilization of stirred mills. In this paper, three energy terms are defined to assist in understanding the breakage mechanism for various types of minerals versus mill operation. The types of minerals studied had diverse physical and mechanical properties that are summarized as specific gravity, hardness and crystal structure. The minerals utilized in this study were quartz and galena. The effect of quartz and galena mix has been addressed as well as Lead-Zinc ore sample from SAG mill discharge. The energy input to the mill is function of the agitator speed, therefore three agitator speeds were evaluated, 1000, 1500 and 2000 RPM, respectively. The energy terms studied are specific energy (kWhr/ton). Effective energy is the ratio between net energy and total energy consumed by the mill. Last type of energy is the specific breakage energy, which is the net energy consumed by the mill per one-micron breakage. Results showed that specific energy and specific breakage rate are functions of mineral type, while effective energy is only function of mill input power (agitator speed).INTRODUCTIONGrinding is the largest energy consuming component of a mineral processing operation and typically consumes about 50% of the total energy used at a mining operation (Botin, 2009). Over the last two decades, stirred mills have been extensively utilized in mineral processing operations due to increased mineralogical complexity of ore bodies. Stirred mills grind particles to less than 10 µm by applying a high power intensity. The technology has been the focus of several research studies to investigate mill energy and grinding mechanisms. Becker, et. al. (2001) studied the relationship between different types of energy including input energy, specific energy, volume/mass specific energies, to stress intensity and final product particle size. Other studies such as by Kwade (1999), Kwade and Schwedes (2002), Blecher et al (1996), Partyka and Yan (2007), Stender et al (2004), focused on mill design and/or stress intensity distribution. Peukert (2004) studied the effect of mechanical properties of the grinding media and ground material on the comminution process."

Jan 1, 2016

By L. M. Lowe, D. B. Chambers, D. G. Feasby

"Potentially economic deposits of rare earth elements (REE) often contain elevated levels of naturally occurring radioactive materials (NORM), primarily thorium and uranium and their associated radioactive decay products. The concentrations of NORM usually exceed typical background levels of natural radioactivity, sometimes by factors of ten or more, and can be of concern relative to occupational radiation protection and the management and disposal of REE mineral processing and metallurgical wastes. This paper provides a summary of the radiological issues normally encountered in the REE concentrate production industry. In addition to an introduction to background radiation and radioactivity, including the thorium and uranium radioactive decay series, radiation levels expected to be encountered in REE concentrate production are outlined. The occupational, environmental and regulatory aspects of REE production related to NORM, including radiation dose limits, radioactive waste disposal guidelines, and threshold VALUES (for the application of transport regulations, are presented.INTRODUCTIONConcurrent with the increasing demand for new sources of rare earth elements (REE) to meet modern industrial needs, there is also an increasing awareness of the radioactivity associated with the REE ores and resources. This is an especially important consideration in addressing questions from the public and local communities who are often concerned about “radiation” and “radioactivity”. Public concern is heightened by reference to legacy issues that arose during times of less regulatory oversight; as well, the benefits of modern technologies, practices and regulation are overlooked. Such concerns are also often inflamed by unfounded claims by non-governmental organizations (NGO’s). Thus, it is important that all concerned have a full understanding of just what the potential risks from radiation associated with REE are, or are not. This paper provides an overview of the sources of radioactivity, the potential implications of radiation and radioactivity in the REE industry, and a brief discussion of established and reliable methods of managing exposure to radiation and radioactivity."

Jan 1, 2012

By A. B. Irwin

"Discussion at MeetingDR. D. DERRY (Ventures Limited) referring to the diagram (Figure 15) which shows a transverse structure section across the Central Slocan area, asked what the assumed structure at depth was, remarking that dips are steeper and more uniform at depth and that the contortions with gently-dipping axial planes are at higher elevations. He wondered whether the section represented ,part of a very large fold with steeply-dipping axial plane.MR. J. D. LITTLE (Canadian Exploration, Limited) replied that E. B. Mayo (Kelowna Exploration Company) and others had considered that the entire section illustrated faces to the southwest and represents part of the lower limb of a great overturned •syncline which is concave toward the southwest.DR. R. DEWIT (Geological Survey) remarked that the photograph of a ripple mark (Figure 7) showed internal lamination conformable to the ripple mark and wondered if the structure was not due to slumping during consolidation, since the normal mode of formation of ripple mark would seem to preclude the possibility of such internal stratification.MR. LITTLE remarked that in his opinion such structures should not be depended upon alone with-out other confirmatory evidence of the direction of tops of beds."

Jan 1, 1952

By Roy EI. Durr, Glen R. Davidge

"This paper presents the results of structural analyses and full-scale destructive tests conducted on liner plate culverts. The purpose of this work was to establish a design method and evaluate the suitability of using these structures in potential roof-fall areas for a rehabilitation application in lower stress and relaxed mining environments. Field evaluation of the design is currently in progress.Theoretical ultimate resistance functions were established for two different culvert shapes and were found to be representative of their experimental behaviour. The ultimate resistance function was used to determine their plastic behaviour to a rapidly increasing deflection condition, to determine the energy absorption capacity of these structures, and to predict their response to impact loading.IntroductionThe Kidd Creek mine of Falconbridge Limited is located justnorth of Timmins, Ontario. The area under rehabilitation for which this program was developed is the 2600 level of the No. I mine. The problem of effectively securing selected drifts at the 2600 level in NO.1 mine, for access to a high-grade ore block, is key to the economics of the operation. Diamond drill test holes had indicated a loosened rock mass above the 2600 level of about 7.5 m thick in response to the extensive mining operation below this level. This level forms the arbitrary boundary between the No. I and No. 2 mines, and has extensive volumes of cemented rock fill below it and largely untouched ore above it to the 2000 level in the North orebody. The walls at that level were showing relaxed ground conditions typical of de-stress: sub-horizontal joints opening up, and peeling.Due to the ground conditions, the consequent safety risks, the high grade of the ore, the potential production delays, and the likelihood of several phases of rehabilitation, regularly used drift rehabilitation employing rock bolts, cable bolting, or shotcrete was not practical. Two options were deemed possible alternatives to suit these conditions, steel sets with blocking and lagging, and liner plate culverts with backfill. Culverts were chosen."

Jan 1, 1995

By Botao Lin, Yan Jin, Hongjuan You, Jingjun Pan, Huiwen Pang, Mian Chen, Sen Chen

"Steam Assisted Gravity Drainage (SAGD) has become the mainstream technology for ultra-heavy oil recovery in Xinjiang oilfield, the success of which depends heavily on shortening of preheating period as well as forming homogeneous and highly permeable zone in land-facies oilsands layer. Towards this aim a special hydraulic fracturing process is required, which is accomplished through controlled water injection to a pair of horizontal wells in order to create homogenously distributed microcracks in the zone between the two wells. The associated mechanical response, however, is unclear for land-facies Karamay oilsands that is loose in texture. In this regard, this research utilizes a triaxial test system on cylindrical specimens extracted from field-collected oilsands cores. Isotropically consolidated drained triaxial compression tests are conducted on both saturated and unsaturated specimens so as to investigate the mechanical response of oilsands at different spots relative to the wellbore. Moreover, acoustic emission and fast pulse-decay permeability are performed to monitor fracture development and permeability evolution. Based on these experimental studies, the mechanism of dilation in oilsands is comprehensively analyzed. The findings reveal distinctive behavior between the saturated and unsaturated specimens as respect to dilation, porosity/volumetric evolution and change of permeability. It is also found that shear bands can be created upon shearing on triaxial specimens, rendering porosity or volumetric strain the factor that is more proper for evaluation of stimulation efficiency in the field.INTRODUCTIONXinjiang oilfield is widely known for its abundant deposit of heavy and ultra-heavy oil that has been estimated to be several hundred million tons. The ultra-heavy oil deposit located in Fengcheng region of Karamay at the northwestern part of the Junggar Basin, Xinjiang, China, has over 360 million tons of resource (Yuan et al. 2013). The resource is deposited in depths from 180 to 450 m and has viscosity over 100, 000 mPa•s at a temperature of 50ºC, bringing technical challenges to recovery activities."

Jan 1, 2015

By Michel David

"The usual complaint of mines is that grade does not match exploration expectations. Quite often, more tons are mined than expected but at a lower grade. This can be seen as dilution. Geostatistics can help predict which dilution can be expected both in terms of grade and tonnage for different mining methods.The usual vocabulary of geostatistics speaks of block distribution; block variance, size effect, information effect, all terms which say very little to the practitioner. In f act, all this can be rephrased in terms of dilution .In this paper, the following is presented - an example which shows how reserves change with the size of selection units and number of samples taken, and tables which show the dilution that are bound to happen when dealing with the commonly encountered log-normal distribution. Finally, the paper shows how grade tonnage computations should be made in the case of an arbitrary distribution. IntroductionGeostatistics progresses more and more rapidly if one judge s by the number and quality of papers published in Mathematical Geology or at APCOM meetings. More and more case studies describing successful applications are published (David et al., 1986)(Kwa and Mousset-Jones, 1987). It is estimated that more than 270/0 of the gold mines around the world use geostatistics. There is still, however, a lot of resistance from the remaining 73%. Geostatistics has more formulae and equations than it needs to reach year 2000. We will be well into the third millenium before all the models available now are actually used. The progress may come in the form of finding better ways to present known statistical results and getting away from the jargon of geostatisticians. One example may be in trying to explain how we can answer the most common plea of the mining industry: production grade is not what was expected in the feasibility study."

Jan 1, 1988

"Dry crushing trials at pilot scale have shown that the IMPTEC Super-fine Crusher has the capacity to generate ultra-fine products from hard mineral assemblages presenting at either coarse or fine feed sizes. The super-fine crusher was introduced at the 27th International Mineral Processing Congress in Santiago Chile, with results from a range of duties, which demonstrated the crusher’s potentially expansive operating scope. This paper focuses on current preparations to progress the technology from pilot scale to commercial scale within a concrete production plant, where lead blast furnace slag will be crushed to ultrafine sizes to generate an active silica product for use as a supplementary cementitious material, which can replace Ordinary Portland Cement. A key objective of the operation is to demonstrate an economical route to reducing the cost of concrete production, improving concrete quality and reducing greenhouse gas emissions. The paper also highlights the potentially key contribution super-fine crushing can make to the long-term viability of iron ore beneficiation by simplifying comminution flow-sheets and reducing operating costs. There is every indication that the technology has the potential to feature universally in metalliferous and industrial mineral flow-sheets. INTRODUCTIONToday’s IMPTEC super-fine crusher is the successful end product of development work over 19 years and is the third particle size reduction device conceived, built and tested over that time. The concept evolved as engineering design progressively developed a mechanism capable of harnessing a highly efficient combination of fundamental particle breakage mechanisms. Early development trials at pilot scale indicated that super-fine crushing had the potential to establish a wet or dry, media free, low energy route to ultra- fine products from hard mineral assemblages. Having achieved some impressive results from open circuit pilot tests on fly ash and granulated blast furnace slag it became clear that the cement industry may well provide opportunities to apply the technology commercially. Following expressions of interest from local cement and concrete plant operators, IMPTEC negotiated an agreement to undertake commercial trials with a SFC 350 super-fine crusher installed on site at a concrete supply plant in South Australia. Super-fine crushing scope was recently expanded following further expressions of interest from research groups involved in the processing of iron ores. Pilot trials are progressing in these areas."

Jan 1, 2016

By Roger J. Goodman

"Major industrial restructuring, which started to manifest itself in the mature economies of the Western World and Japan in the 1970s, will accelerate in the 1980s and 1990s. Conventional heavy manufacturing industries will continue to lose ground to lighter processing/assembly operations and the new wave of high technology, information and service sectors. The decline in heavy manufacturing has severely impacted on the steel industries of Western Europe, the U.S.A . and Japan.World trade in metallurgical coal has shifted correspondingly, with declining demand in the mature developed countries being only partially offset by large increases in the steel intensity of the newly-industrialized countries (NICs) of the Far East, Latin America and, to a more limited extent, the Middle East and Africa. These trends will be accentuated in future years with direct implications for the distribution of metallurgical coal trade. This paper discusses, in quantitative terms, such changes in the 1980s and 1990s, and examines the implications for, and impacts on, Canadian metallurgical coal exporters.IntroductionThe twenty-year period from the early 1950 s to the early 1970s was characterized by inexorable growth in consumer demand and industrial expansion in most of the advanced countries of the western world. Long- term forecasting during this period typically used linear extrapolation techniques which , despite their simplicity, invariably ended up predicting future demand and production level s with uncanny accuracy. Times have changed!The last decade has been characterized by a n abysmal failure of our economies to respond to simple long-term, linear growth patterns. We appear to have entered a new world in transition, where we can observe a wave of dying or sunset industries reluctantly being submerged by a wave of emerging or sunrise industries.This paper is aimed a t examining the evidence for long-term industrial restructuring trend s. For want of a better word, these so -called, megatrends are then used to predict future demand level s and spatial distribution of steel development and , hence, metallurgical coal trade. It is tempting to correlate the decline in economic activity in the western world with the first Organization of Petroleum Exporting Countries' (OPEC) crisis of 1973. This crisis was probably no more than the straw that broke the camel's back, as the megatrends and embryo s of major industrial restructuring were already evident. Today these megatrends are merely more apparent and transparent than they were ten years ago.While the concept of industrial restructuring is the new economic buzz word, the process was at work, to a lesser degree even throughout the period of strong economic growth of the post-Second World War boom. Many people still remain convinced that our present-day sluggish economy is just part o f the typical , though rather more prolonged, recessionary cycle. Yet, we have always been part of a dynamic economic system and industry throughout history has been the subject of a continuous process of evolution, restructuring and reconstitution . Now the time is ripe to examine the evidence for such restructuring in order to develop coherent policies of adjustment in this transition from one industrial regime to another."

Jan 1, 1985

By John Steele

The goal of this project is to detect the presence of objects behind haul trucks and to provide an alarm to the driver if such objects are detected. Objects of interest include people, pickups, other equipment, and large rocks. Another goal is to see if the system can identify the existence of a berm and determine the distance from the truck to that berm, so a safe backup distance can be computed and used as a reference. This paper presents results that demonstrate that such a system is feasible and includes results from work at a local quarry. Architecture of the system is provided and the various subsystems are discussed. Details of the algorthims are included and discussion of the issues involved in developing a fieldable system are also included.

May 1, 2003

By C. O. Aksoy

"Pillars left to ensure the stability of major underground coal mine infrastructure (shafts, drifts) often contain substantial quantities of coal. Recovery of this coal is an efficient use of the resource, but often presents safety hazards; pillar extraction destabilizes the protected structure, and can make its use dangerous. In this study, the stability of an active shaft at an underground coal mine situated in the Soma- Manisa region of Turkey was investigated during the recovery of the coal in the shaft safety pillar.A proprietary three-dimensional finite element analysis model (ANSYS) was used. An elastic-plastic material model utilizing the Drucker-Prager failure criterion was employed. The three-dimensional Drucker-Prager formulation was preferred over the two-dimensional Mohr-Coulomb model because it was thought to more accurately represent the strain hardening behaviour shown by most geologic materials.Stresses and deformations formed around the shaft support were estimated using the model and the results were verified by in situ observations. The results show that stress distributions around the shaft and the subsidence of the shaft support are influenced by the location location of the extraction front and the break angle of the overlying material."

Jan 1, 2005

By J P. Bolduc, P. E. Pelletier

Preceded by brief general considerations such as the development of the mining industry in. the Province of Quebec, the choice of plant location, the types of problems studied etc., the paper gives a complete description of this new research and treatment center for metallic, non-metallic and asbestos ores. Facilities for carrying out operations in the three sections of the plant -the sampling section, the ore treatment section and the asbestos section -are fully discussed as well as laboratory facilities for (a) the preliminary testing of ores prior to pilot plant treatment and (b) the grading and testing of asbestos fibre. AT THE beginning of the century, the annual value of the mineral production of the Province of Quebec stood at the $2,500,000 level. Twenty-five years later, it was just under $24,000,000. In 1950, half a century later, it was slightly in excess of $200,000,000. But in 1959, in the span of only nine years, it

Jan 1, 1962

By M. P. Filion, K. Ferguson, L. L. Sirois

Acidic drainage is the largest single environmental problem facing the Canadian mining industry today. Technologies to prevent acidic drainage from occurring in wasterock piles and tailings sites, and on the walls of open pits and underground mines, need to be developed and demonstrated. There are two groups in Canada which have accepted this challenge: the national Mine Environment Neutral Drainage (MEND) program and the British Columbia Acid Mine Drainage (BCAMD) Task Force. This paper summarizes the activities of these two organizations.

Jan 1, 1990

By Kenneth Blower

This paper gives a detailed coverage of the ore flow through the primary crusher, cobbing plant and concentrator, including equipment sizes, recoveries, reagent consumptions and product descriptions. Special features, such as rubber chutes, rubber-lined mills, pebble-mill grinding, steam-hooded filters and process control instrumentation, are also discussed.

Jan 1, 1968

By F. J. Hrach, K. P. Flynn, P. J. Miranda

"ST Equipment & Technology, LLC (STET) has developed a processing system based on tribo-electrostatic belt separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. In contrast to other electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the triboelectric belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (300 µm) particles with very high throughput. The high efficiency multi-stage separation through internal charging/recharging and recycle results in far superior separations that can be achieved with a conventional single-stage free-fall tribo-electrostatic separator. The triboelectric belt separator technology has been used to separate a wide range of materials including mixtures of glassy aluminosilicates/carbon, calcite/quartz, talc/magnesite, and barite/quartz. Separation results are presented for selected industrial mineral sources. An economic comparison of using the tribo-electrostatic belt separation versus conventional flotation for barite / quartz separation illustrates the advantages of dry processing for minerals.INTRODUCTIONThe lack of access to fresh water is becoming a major factor affecting the feasibility of mining projects around the world. According to Hubert Fleming, former global director for Hatch Water, “Of all the mining projects in the world that have either been stopped or slowed down over the past year, it has been, in almost 100% of the cases, a result of water, either directly or indirectly” (Blin et al., 2013). Dry mineral processing methods offer a solution to this looming problem."

Jan 1, 2016

By C. Beaudry

Outline ? General Geology of Frieda River Project Area ? Exploration History ? Geology of Porphyry Deposits ? Porphyry Resource ? Update of Nena Deposit and High-Sulfidation Mineralization ? Nena Resource

May 1, 2006

By Jodi Wilding, Barry Lurnsden

The implementation of new technology to mineral separation operations requires rigorous testing to confirm the technology&apos;s technical and economic benefit. The Jaguar Mine owned by Jabiru Metals is located in Western Australia and sequentially separates a copper concentrate and then a zinc concentrate. Fine grinding (80% of zinc in tail is <25µm) is required to achieve efficient mineral separation. All mineral losses are therefore fine mineral losses, and so improvements in metal recovery must focus on this fine mineral. Magnetic aggregation technology has been shown to increase the recovery of fine paramagnetic minerals so it was an appropriate technology to evaluate at Jaguar. Testwork commenced in the copper circuit and it was found that there was a substantial reduction in copper in copper tail and an increase in zinc recovery to the zinc concentrate. The increase in zinc recovery in the latter zinc circuit was an interesting result and initiated the second stage of testwork that was to install and test a second magnetic conditioning unit in the zinc círcuit. This showed a further increase in zinc recovery. Magnetic conditioning technology has now been fully evaluated in the plant and is now part of the Jaguar flowsheet.

Jan 1, 2011