Search Documents

By T. Motegi

Semisolid casting provides grain refinement of the cast structure and prevents macro-segregation. The conventional semisolid slurry is obtained by electromagnetic or mechanical stirring. In our process, the magnesium alloy (AZ31) slurry is made using an inclined cooling plate instead of the conventional methods. The slurry obtained is cast into a twin-roll caster and makes a continuous sheet of 2 or 3 mm thick. The most important factors that influence the sheet casting are the casting temperature and twin-roll speed.

Jan 1, 2007

By O. Kangal, G. Önal, G. Bulut, A. Gül

The recovery of copper and cobalt from the ancient copper slags, located in Küre-Turkey, is investigated. Fayalitic type of ancient copper slags containing 1.41% Cu, 0.53% Co and 53.16% Fe were subject to the experimental study. Magnetic separation, gravity concentration and flotation test were conducted. The results of magnetic separation and gravity concentration were not satisfactory. However, a concentrate containing 9.57% Cu could be produced with 44.7% recovery by flotation. Copper and cobalt that remained in the flotation tailings was recovered by roasting with sulfuric acid followed by hot water leaching. Complete cobalt dissolution was observed in 1 hour of roasting at 150°C and 3:1 acid/slag ratio, whereas the copper recovery was 83%.

Jan 1, 2004

By R. W. Brock

This subject is too broad and comprehensive to be dealt with adequately and authoritatively in this paper. It calls for the knowledge and experience of many men, but the results from such collaborative effort would be of great value, particularly if similar reports of the principal mining districts of the world were made on a standardized basis so that conditions everywhere might be directly and accurately compared. In considering conditions affecting mining in British Columbia, unfavourable as well as favourable factors must be taken into account. The unfavourable are apt to loom large and to be exaggerated rather than minimized; for it is human nature to see the blackness of the cloud rather than the silver lining; to think that one's own undertaking is beset with peculiar difficulties, and to attribute lack of greater success to out-side causes rather than to personal shortcomings. It should be recognized, however, that there is no country where the conditions for mining are ideal. The ideal mining country is the product of imagination, invested with every favourable condition found anywhere, but with none of the unfavourable conditions that are always present in reality. So if British Columbia has some handicaps to the industry, it is in good company. What is important is that the advantages compensate for the disadvantages, that the balance will compare favorably with that of competing states, for mining, like every other industry is competitive, and the cost of one's product must have a definite relationship to its price in the world's market.

Jan 1, 1924

By Roger J. Goodman, Don Riva

"IntroductionCrows Nest Resources Limited (CNRL), a wholly-owned subsidiary of Shell Canada Resources Limited, is nearing completion of its first coal project, located in southeastern British Columbia. CNRL shipped over 700,000 tonnes of thermal coal to foreign markets in 1982. With the completion of the metallurgical coal plant in December, 1982, shipments of both thermal and metallurgical coal will increase substantially in 1983 and will approach the anticipated operating capacity of 3.0 million tonnes in 1985. The Line Creek Mine lies some 25 kilometres north of Sparwood in southeast British Columbia (Fig. 1). The open-pit mine is located on top of Line Creek Ridge, with coal being hauled 16 km to the thermal and metallurgical coal preparation plants, situated adjacent to the already existing Canadian Pacific Railway. Most of the coal is moved by 108 car unit trains by CP Rail to coal ports in Vancouver, where it is loaded onto vessels destined for overseas markets. Some smaller scale car load shipments are moved by rail to contiguous markets in the Pacific Northwest. History The southeastern British Columbia area, known as the East Kootenays, is steeped in a rich coal mining heritage, dating back to the latter part of the nineteenth century. Predecessors of Crows Nest Resources Limited were instrumental in developing the rich coal reserves in the area. In 1887, William Fernie, a pioneer-cum-prospector recognized the potential of coal deposits in the East Kootenays. Spurred by the relentless push west of the Canadian Pacific Railway through the Crows Nest Pass area, Fernie recognized that it was just a matter of time before the steam locomotives provided him with his required market. That time arrived in 1897 when Fernie helped to form the Crows Nest Pass Coal Company and coal mining commenced at Coal Creek, near his namesake town of Fernie. During its almost 70-year history, this company produced over 48 million tonnes of steam coal and 8 million tonnes of coking coal. In 1965, the Crows Nest Pass Coal Company was re-named Crows Nest Industries, to better reflect its expanded interests into forest products, and it is the latter company which Shell Canada Resources Limited acquired in 1978. The extensive coal resources of Shell, in both Alberta and British Columbia, were rationalized into one group with the birth of Crows Nest Resources Limited to manage and develop the coal holdings."

Jan 1, 1985

By R M. Ennis, J. C. Botham

This paper is one of a series pre-pared to study the role of fuels and reductants in metallurgical processes, especially from the viewpoint of Canadian requirements. The object of these studies is to provide a reason-ably authoritative interpretation on the interrelation of fuels in light of the considerable changes that have taken place in the Canadian energy field during the past few years. Previous papers in this group have dealt with the problem generally, and specifically in terms of the development of the iron and steel industry of Western Canada. These latter papers, presented at the Symposium on Iron and Steel in Western Canada held in Edmonton, Alberta, on September 8-9, 1959, surveyed the ferrous processes of interest for use in Wes tern Canada, especially with regard to solid fuel requirements. At that time it was evident that there was a need for a similar study of the fuels aspect of the non-ferrous metals industry.

Jan 1, 1961

In terms of throughput, product size and power draw, grindcurves provide a measure of the response of the mill performance to changes in mill operating parameters – usually mill filling. Since presenting the principle in 2006, grindcurves have been applied to a wide variety of AG and SAG mills. Mill response has been carefully measured for variations in: mill fillings from 15% to 40%; throughput by a factor of two; power by 50%; feed blends; liner profile; and mill speed from 65% to 80%. The outcomes of this extensive program of work are presented as the measured grindcurves. How they have enhanced our understanding of mill operation and how they may be applied to practical daily mill control is discussed. It is proposed that this technique provides a viable and valuable mill control tool that may find extensive application in the industry.

Jan 1, 2012

By L. T. Raevskaia

We discuss the stability problem of a piston of the reversible axial-piston pneumatic motor called DAR-14M. We performed the full analysis of stress and deformation characteristics of the piston near a resonant frequency with the help of FEM ANSYS. We estimated the own frequency of the piston analytically for the given motor, this estimate was confirmed numerically in the model analysis FEM ANSYS. It was also shown in harmonic analysis that loaded piston end behaves very different in comparison to the unloaded end. As expected, maximum deformation was found in the area of the holes of the bearing shaft, indicating an optimization necessary in that region of the motor.

Aug 1, 2013

By Graham A. Davis, Michael Samis

The dramatic fluctuation in metal and energy prices in the last few years is causing mining companies to consider alternative analytical methods for mine design and valuation. The goal is to improve insight into unforeseen changes in the economic and project environment and to design projects that take advantage of management's ability to respond to these changes. Such flexibly managed projects will contain value that cannot be measured using traditional engineering economic approaches, further motivating the used of alternative, modern valuation methods. This paper considers the valuation of an uneconomic low-grade resource at an open pit gold mine using two of the most popular modern valuation methods, Dynamic Discounted Cash Flow and Real Options. Our analysis demonstrates that the conventional valuation method may incorrectly represent the value and risk attached to mining this type of resource because it is unable to recognize management's ability to respond to future events in a manner that minimizes losses and exploits advantageous business conditions. The results of this paper highlight the importance of recognizing flexibility and business uncertainty in both mine design and valuation.

Jan 1, 2003

By F. Parada

During copper smelting and converting processes, slag generated is pyrometallurgically cleaned and then disposed, containing around 1 % of this metal. However, important amount of molybdenum initially contained in concentrates also goes to the slag phase. Research on molybdenum recovery from water granulated slags using acid leaching at low temperatures was conducted to find an efficient way for molybdenum extraction with lower magnetite in the slag. However because of the high fayalite content high acid consumption was found. Molybdenum can be recovered from solution using ionic exchange resins, but high silica content interferes with extraction. Some studies addressed to minimize silica extraction as well as alternatives of selective silica precipitation in order to develop a technically feasible process.

Jan 1, 2007

By T. Kawai

Japan Oil, Gas and Metals National Corporation (JOGMEC) has started an exploration program for Seafloor Massive Sulfides (SMS) in the EEZ of Japan, and launched an investigation program for mining, processing and environmental impact on SMS development. With regard to the mining aspect, the mining system consists of three units: a mining unit on the sea floor, an ore lift-up unit to surface, and a mining support vessel unit which has an ore unloading system that unloads onto a shuttle ship. Regarding the mining unit, JOGMEC and certain Japanese mining and machinery companies developed two types of state of the art mining testing tools. Excavation tests on the actual SMS site in the Okinawa Trough, south-west of Japan, were conducted in 2012. In these tests, the functions of the testing tools, such as cutting ore, moving on the seafloor and climbing up slopes having steeper than a 25 degree gradient, were confirmed. The physical characteristics of the ore, which are key parameters for establishing a mining system, are yet to be fully understood as the exploration program has been undertaken simultaneously. Hence, those examinations have been carried out by ground cutting experiments, analysis of drilling core data, and the like. This paper describes the outline of a proposed mining system, mining testing tools and results of the on-site mining testing.

Aug 1, 2013

By R. C. Gegg

The property of MacLeod-Cockshutt Gold Mines, Limited, is in the Little Long Lac area of the Thunder Bay Mining Division, Ontario, about four miles south of the Canadian National railway station of Geraldton. The town of Geraldton is about 170 miles east of Port Arthur and 22 miles west of Long Lac, which is on the main line of the Canadian National railway. The Trans-Canada highway passes through the property and during the winter season the road is maintained between Port Arthur and Long Lac. Electric power is supplied by the Hydro-Electric Commission of Ontario from their Cameron Falls plant and is distributed at 44,000 volts by a local transformer station. Early History The South orebody was discovered by diamond drilling in the spring of 1936. This is a porphyry contact orebody with major pyrite and minor arsenopyrite mineralization. Some gold is present in the 'free' state, but for the most part it is locked in the pyrite, with little or none in the arsenopyrite. Preliminary test work was based on comparing straight cyanidation with bulk flotation and cyanidation of the concentrates. The overall results by the two methods were found similar, but for economic reasons the flotation-cyanidation process was adopted. Before the mill came into operation, a new and entirely different type of orebody, consisting of massive sulphide lenses in banded iron formation, was discovered to the north of the existing workings. These bodies are an intricate mixture of pyrite and arsenopyrite, both carying gold.

Jan 1, 1949

By Yi Yang, Mark Zoback

"We report laboratory studies of the time-dependent deformation of core samples from four different formations in the Williston Basin - the Lodgepole formation, the Middle and Lower Bakken formations and Three Forks formation. The laboratory tests reveal varying amounts of viscoplastic deformation in response to applied differential stress. The time-dependent deformation is generally greater in rocks with higher clay and organic content, and can be described by a power-law function. Because the magnitude of the creep strain is linearly proportional to the applied differential stress, we can utilize viscoelastic theory and geophysical logs to estimate the degree to which tectonic stress is affected by viscoplastic stress relaxation. We suggest that viscoplastic stress relaxation results in the Upper and Lower Bakken Formations act as frac barriers during hydraulic fracture stimulation in the Middle Bakken, but the Lodgepole and the Three Forks Formations are not frac barriers.INTRODUCTIONHorizontal drilling and multi-stage hydraulic fracturing in shale reservoirs are critical for successful exploitation of ultra-low permeability shale gas, tight gas and shale oil reservoirs. Characterization of the mechanical properties of the reservoir rocks is essential to understanding the behavior of rocks during drilling and completion. Previous laboratory studies have shown that the timedependent deformation in clay-rich shales can be characterized as linear/viscoelastic deformation (Chang et al., 1997; Hagin and Zoback, 2004a, b; Sone and Zoback, 2013b, 2013c). Sone and Zoback (2013c) showed that laboratory measurements of time-dependent deformation in various gas shale reservoir rocks, and demonstrated that the viscoplastic deformation of these rocks can be characterized by a power-law function. They interpreted the results in the framework of linear viscoelastic theory to quantitatively assess the geomechanical effect of viscous time-dependent deformation over engineering and geological time scales. (Sone and Zoback, 2014) further extended the theory and proposed a viscous relaxation model that can be applied to predict the continuous differential stress magnitude using the geophysical logs. They tested the validity of their model by comparing the stress prediction with the occurrence of drilling induced tensile fractures (DITFs) and the vertical hydraulic fracture penetration observed from microseismicity."

Jan 1, 2015

By Ralph L. Rutherford

Introduction During the past twenty-five years we have seen considerable exploration for oil on the plains of southern and east-central Alberta. This exploration has to some extent gone on in cycles, with periodic starts, stops, and occasionally some reversals. Each major attempt is usually supplemented by the application of some new method of exploration and, following each period of exploration, drilling tests are made. Whereas oil-bearing horizons are the ultimate objective of these explorations, the preliminary investigation frequently aims at a discovery of structure based on the long accepted belief that accumulations of oil and gas are to a marked degree structurally controlled. At the inception of this general exploration for oil, it was natural that attention should be directed to areas where there was surface evidence of deformation of the underlying strata, but, as the programme progressed, it was found that these surface manifestations of structure were often deceptive when attempts were made to project them to depth, to involve the deeper strata. Drilling of test wells was the only satisfactory method of obtaining exact information.

Jan 1, 1946

By K. Iturralde

The article discusses the possibility of automation in refurbishment processes of social dwelling built from 1950 to 1970. These massively produced buildings were mostly designed prior to the law enforcement regarding thermal insulation or accessibility. Nowadays, many of these buildings are being retrofitted. The article focuses on the works in the external envelope. The task of renewing the whole social building stock is big and it requires a systematic process that facilitates a rapid upgrading, without neglecting the specific situation of each case. How could an automatic refurbishment process of these buildings be defined? The process should start with the data collection of the building and the creation of a 3D model using software such as BIM. The project, drafted in 3D, should facilitate the manufacture of building elements by robotics. In turn, it should be noted that during the assembly at the site, the pieces must be fixed quickly and efficiently. Is it possible to implement an automated process for the refurbishment of apartments built in the second half of the twentieth century? To approach the answer, a virtual refurbishment project is performed. The article focuses on the rehabilitation of the building envelope. Furthermore, it gives special attention to the double skin facade. It is well known that a second skin in this type of building can be an element that integrates several functions. Finally, needless to say that refurbishment of residential buildings is a need in our society. By extending its life cycle, robotic refurbishment provides more favorable socioeconomic and environmental capabilities than the sole construction of new buildings.

Aug 1, 2013

By J. E. Hawley

"The Aldermac copper deposit is in Beauchastel township, Abitibi county, Quebec. It lies about 11 miles west of Noranda. It has been described by Cooke, James, and Mawdsley(2) and by Bruce(3) and has been mapped in detail by W. Samuel and the late K. W. Fritzsche, former Mine Geologist, and by J . E. Gill and A. R. Byers, so that most of the particulars contained in the description that follows are largely the result of the work of others than the writer, whose connection with the deposit, in a consulting capacity, extended over the last 5 years of the life of the mine.According to A. V. Corlett, former Mine Manager, the property was staked during the early winter months of 1923 because of its location adjacent to the syenite intrusive that had been mapped by Cooke near the height-of-land in this township. An examination by Mr. Corlett in 1924 revealed mineralized zones to the north of MacKay lake, and in the vicinity of these K. W. Fritzsche, by dip needle and trenching, discovered the No. 1 and No. 2 deposits, which were both too small and too low grade for exploitation. During the winter of 1925, A. A. MacKay, with a dip needle, picked up a magnetic 'anomaly' in a drift-covered area about 600 feet to the north of previous workings. Trenching here revealed only a narrow zone of mineralization of little consequence, but, farther east, MacKay discovered a more pronounced 'anomaly' over what later drilling and underground work proved to be ore of commercial grade (No. 3 and No. 4 orebodies)."

Jan 1, 1954

By Mike Smith, George Chung

"A 23 million dollar Flotation Plant has been commissioned at the Iron Ore Company of Canada in 1998. Nine OK-50 cells &re used to float silica in this 1,400 tomes per hour plant. The paper details project development, construction and operating results. This plant gives IOC the capability to produce not only high quality blast furnace pellets of varying silica, CaO and MgO levels, but also a high iron, DR grade pellet. The first activity was simply to sit down with the suppliers, Outokumpu, Wemco. GL&V and Svedala, to discuss applications and share experiences. We learnt what each supplier had to offer, what features would particularly suit this application, what options were offered, what were the materials of construction, how the equipment is maintained, which wear parts require replacement, etc., etc. We tried to learn as much about the equipment as the suppliers themselves knew. Then we tried to learn more: we contacted users and asked about any weak points, which options were worth incorporating and which items were not. We then discussed these points with the suppliers and established how potential problems might be overcome."

Jan 1, 1999

"THE OTTAWA BRANCH, CIM, each year holds a symposium on a subject of topical interest. The symposium this year was on Canada's Offshore Mineral Resources, at which papers were presented by: Dr. Donald G. Crosby, chief, Resource Administration Di-vision, Department of Energy, Mines and Resources, Ottawa; John A. Beesley, head, Legal Division, Department of External Affairs, Ottawa; and David W. Smith, man-ager, offshore exploration and production, Shell Canada Limited, Calgary. Because of the interest which this topic holds for our members, and because of the wealth and significance of information presented, the three papers -representing the first comprehensive review of our offshore resources -are reproduced herewith. The opening remarks of the Chairman, Dr. F. K. North, Professor of Geology, Carleton University, are also recorded, together with a few of the questions asked by the large attending audience. The symposium was held February 13th, and was organized by Dr. W. M. Tupper, chairman of the Branch Program Commit-tee. Differences in the extent of the continental shelf will be noted in the papers. These differences are related to slightly different definitions of the continental shelf by the authors."

Jan 1, 1969

By John Battista

Uranium mining in Australia has a chequered history. This paper reviews the development of the Australian uranium mining industry from the 1930?s to the present day. It outlines the geology of the various deposits and the mining and metallurgical techniques used to extract the uranium. The industry is profoundly affected by government policies and the paper considers the roles of the Federal, State and local governments. The influence of public opinion on nuclear issues and the effects current and historical policies of various governments have had on uranium mining are outlined. Despite heavy restrictions placed on it, Australia?s uranium mining industry has maintained its place as one of the world?s largest producers. This paper also provides an outline of where the industry in Australia may be headed in future.

Aug 1, 2010

By H. Yasuhara, N. Kinoshita, S. Nakashima, K. Kishida

"In this study, flow-through experiments in fractured rocks have been conducted under different stress, temperature, and pH conditions so as to understand the evolution of permeability induced by these conditions. Throughout the experiments, the confining pressures and temperatures are well-controlled. Effluent concentrations are also measured for the ten elements of Si, Al, K, Fe, Ca, Na, Mg, Ti, S, and Cl that are included mainly in the targeted rocks. In the early stage of the experiments, the fracture permeability measured abruptly decreases with time, and subsequently reaches quasi-steady state within a relatively short period. In contrast, the permeability in the intact rocks monotonically increases with time. The permeability increase and decrease are attributed likely to the relative dominance of mineral dissolution in the pore spaces and to that of mineral dissolution/crushing at the propping asperities within the fracture and/or mineral precipitation onto the free surfaces, respectively. The evolving rates and magnitudes of the permeability are likely to be controlled by the stress exerted over the contacting asperities, temperatures, and pH of the permeant. Thus, this complicated behavior should be attributed to the coupled chemically- and mechanically-induced effects, which should be examined in more detail for longer period to contribute to the safe entombment of radioactive wastes. INTRODUCTIONUnderstanding of the flow and transport characteristics of porous/fractured rocks is required for the safe and long-term geological isolation of energy-related by-products (i.e., high level radioactive wastes and anthropogenic CO2). Notably, under relatively high temperature and stress conditions, mechanically- and chemically-mediated processes may alter the pore structures in rocks, resulting in an irreversible evolution of the flow and transport behavior. Augmentation in permeability may result from mechanical dilation due to shearing and mineral dissolution within the pore spaces, while reduction may result from reversible or irreversible mechanical compaction, mineral dissolution at the contacting areas, and clogging of pore spaces by precipitation of secondary minerals."

Jan 1, 2015

By K. Hawboldt, J. E. Halfyard, C. Bottaro

The removal of sulfur from leach residues has been practised in the zinc industry using a combination of flotation and hot melt filtration. The process is highly dependent on the nature of the concentrate and the subsequent residue. When the mineral constituency of the residue alters, the process can encounter significant operational challenges. An alternate method of converting elemental sulfur to water-soluble polysulfides was applied to leach residue from Vale's nickel demonstration plant in Argentia, Newfoundland. Reaction parameters, sulfur purity and other key indicators are discussed as is the potential commercial application.

Jan 1, 2011