Search Documents

By G. Heinrich

Size by size recoveries and pentlandite liberation data from image analysis were used to evaluate plant tests of pentlandite flotation and pentlandite/pyrrhotite middlings flotation from pyrrhotite in a circuit treating low grade magnetic intermediates at the Strathcona Mill. Raising the pH with lime gave improved selectivity for liberated pentlandite but there were major losses of middlings unless the circuit was pulled hard indicating the need for finer regrinding. However, size by size recoveries at the normal regrind showed that, while the pentlandite recovery improved in the finer ranges, the pyrrhotite recovery also increased leading to little selectivity in any size range. A much finer regrind gave greatly improved selectivity in all size classes suggesting that 'surface polishing' as well as liberation effects were being seen. Using liberation data from image analysis of the products, surface polishing accounted for over 99 % of the improvement in selectivity. Unreasonable recoveries of more highly liberated particles were observed for liberation analysis by volume fraction but showed the expected trend in recovery when the analysis was based on surface liberation. The surface liberation data showed that the improved pentlandite recoveries after finer regrinding were to more than 90 % caused by improved liberation with the remainder contributed by surface polishing effects. The practical implications of this work are that i) the comparison of particle grades with product grades allows to estimate the effect of regrinding on co-flotation/entrainment, ii) surface liberation models should be used for evaluating recoverabilities by flotation and iii) regrind circuits may be set up to ensure that all particles go through the mill or that only the coarse fraction is reground depending on the surface scrubbing found to be required.

Jan 1, 1993

By C. Paulo, W. N. Wheeler, M. Kalin, M. P. Sudbury

Many researchers have tested the addition of various phosphatic materials, including Natural Phosphate Rock (NPR), to mining wastes. It was assumed that iron in the waste would form FePO4 precipitates, restricting oxygen access to pyrite surfaces and reducing oxidation. Phosphate additions were based on stoichiometry (phosphate mass to sulphide content of waste). Although some interesting, positive results were obtained with low dosages, these were considered accidental, not having followed the expected stoichiometry. In 1991, we began experimenting on tailings and waste rock with NPR, postulating that if chemo-lithotrophic microbes on the mineral surface accelerate oxidation, then heterotrophic (oxygen-consuming) microbes would reduce oxidation. All wastes with NPR produced effluents with elevated pH and low metal acidity. Later, microscopic investigations of the rocks found an organic layer on the mineral surface, which was confirmed by independent research organizations repeating experiments with very low NPR mass additions to sulphidic wastes. In 2013, heterotrophs were identified and quantified as they grew on German lignite with NPR. These data conclusively showed that the development of heterotrophic biofilms is a consequence of adding waste NPR leading to a reduction of sulphide oxidation and improved effluent from sulphidic mining wastes. We document our gradual understanding of the effects of NPR on the reduction of sulphide oxidation, covering 23 years of research.

Jan 1, 2014

By Kamran Esmaieli

Open Pit Mining Through Underground Voids: Challenges Main Challenges/Hazards: Unexpected collapse of the pit floor and/or pit walls; The loss of equipment and/or people into underground voids; Loss of explosives from blast holes that broken through into the underground voids. How to address these challenges? An important step that must be integrated into mine planning and design is the accurate detection and delineation of underground voids. (i.e. probe drilling, Geophysical techniques, laser scanning,?); Leaving a pillar of adequate thickness between the working bench and the underground voids; Backfilling the underground voids from surface using vertical or inclined raises; Monitoring the working locations (pit floor and pit slopes) to detect movements.

May 1, 2013

By Patrick Rennkamp, Wolf-Dieter Trodel, Andy Fearn

"The Jansen shafts are completed using purely mechanical excavation. This paper summarises the geology, a description of the shafts, the method used for excavation and the results achieved along with the challenges encountered and the solutions developed during the project. This experience is now being applied in the next generation machines and shaft sinking processes. This pioneering approach is changing shaft sinking in soft and medium to hard rock. INTRODUCTION The Jansen Mining project located approximately 150 km east of the city Saskatoon is the location of the BHP owned potash mine with an expected mining output of eight million tonnes annually upon completion. Mining contractors DMC Mining Services have used two Herrenknecht Shaft Boring Roadheaders (SBRs) to excavate the two blind shafts with an approximate excavation diameter of ten metres (inner diameter approximately 8.3 m) to depths of -975 and -1005 metres, respectively. The SBRs excavate the rock by a partial-face cutting method, using a transverse cutting drum mounted on a telescopic boom. The excavated rock is then conveyed away from the bench by an innovative pneumatic system and transferred into muck buckets to be hoisted to the surface. No drilling and blasting was done to keep to the BHP philosophy of using only mechanical excavation for this reference project. BHP VISION – MECHANICAL EXCAVATION BHP focused on mechanical excavation at Jansen due to the following perceived benefits: 1.No workers in the excavation chamber (shaft bottom), minimizing the exposure to traditional shaftsinking hazards associated with working in the shaft bottom. 2. Minimal damage to the rock fabric reducing the need for ground support and avoiding potential impact damage to freeze tubes located around the shaft. 3. Accurate excavation diameters with no overbreak, reducing volumes of rock to be removed and replaced with concrete lining."

Jan 1, 2019

By Y. Long

The deep-hole surface blasting technique is a prime method of iron ore mining. Blasting fragmentation is one of the important economic indicators that measures the blast method to obtain the iron ore. To improve the efficiency of the blasting method and further reduce the cost of the subsequent processing of iron ore, this paper summarizes measured data gained from a certain amount of blasting test conducted in an iron ore mine in Guangdong province, China. According to the data analysis, there are differences on iron ore blasting fragmentation by different indicators of deep-hole blasting, such as decoupling coefficient of charge, contact state between charge and borehole wall, and change of detonation position in charge. These factors were compared in terms of relevance and impact. Research shows: under certain rock conditions, the decoupling coefficient of the charge has a best range related to blasting fragmentation. Since the detonation position in charge determines the direction of propagation of the explosion stress wave through ore and rock, bottom initiation and mid initiation will help to improve the iron ore blasting fragmentation in joints fractured rock and ore. The research conclusions have important application value for program design of iron ore surface blasting and to guide other types of rock surface blasting.

Aug 1, 2013

By Donald MacFadgen

Since 1950, a total of 164 miles of levels and rooms have been roof-bolted in the collieries of the Dominion Coal Company. Roof bolting is an efficient and economic method of sup-port where heavy timber sets or steel booms are necessary for temporary roof support, or where conventional methods of support interfere with the passage of mechanical mining equipment. This paper discusses present roof bolting practices and special bolting applications. THE practice of roof bolting in be collieries of the Dominion Coal Company dates from 1950, when preliminary studies and experiments were carried out in a mechanized room and pillar section of Dominion No. 20 Colliery. These studies were made in close liaison with members of the United States Bureau of Mines who were conducting similar studies. Following the successful application of roof bolting in No. 20 Colliery, this method of roof support was introduced into other collieries

Jan 1, 1963

By B. W. Raymond, D. W. Zandee

"IntroductionCoal deposits are found in many regions in Canada and vary widely in their age, quality and rank. All classifications of coal except anthracite are found in significant quantities in this country.Deposits in the Maritimes are mainly bituminous; Lignite is found in Saskatchewan and Ontario and sub-bituminous coal in the plains region of Alberta. The Rocky Mountain coalfields of Alberta and British Columbia contain low and high-volatile bituminous coal and, in a few places, semi-anthracite. The British Columbia interior contains deposits of semi-anthracite, bituminous, sub-bituminous coals and lignite. The Yukon and Northwest Territories also contain substantial deposits of bituminous coal and lignite.Currently Nova Scotia produces both thermal and metallurgical coal, Saskatchewan produces lignite and Alberta produces both sub-bituminous and bituminous coal for thermal purposes. Large deposits of metallurgical coal are now being exploited in the Rockies arefl of British Columbia and Alberta by open pit methods. The raw coal is treated in large capacity preparation plants to remove refuse and upgrade the product to a consistent metallurgical quality with respect to ash, moisture, volatile matter and coking properties.The treatment of coal involves crushing, screening and cleaning by dense medium, jigs, water-only cyclones, tables and froth flotation to produce a diverse range of coal products differing in quality and size for various end uses.The chapter on Crushing and Screening Circuits was concerned mainly with crushing of metalliferous ores to produce a concentrate of one or more valuable minerals which normally constitute a small portion of the original mass of the material treated.Coal differs physically from ores in many ways such as lower specific gravity, relatively large volumes but low tonnage of product, and its habit of absorbing moisture requires extensive dewatering processes more complicated than settlement and filtration. Most significant, for this paper at least, is the fact that crushing coal is not as energy intensive and much smaller equipment is applicable.Crushing and screening of ores is intended to reduce the size of all constituents as quickly and efficiently as possible to allow liberation of the mineral particles. The crushing of coal is different in that the coal is not the minor constituent and the production of fines, in the initial stages at least, is highly undesirable. The basic objectives of crushing coal are the reduction of run-of-mine material to sizes suitable for cleaning or further reduction of coal to market sizes."

Jan 1, 1989

By Yi-Chun Lin

Mechanical/Electrical/Piping (MEP) systems, due to their complexity and diversity, are the most intricate part of building construction. This being the case, Combined Services Drawings (CSD) and Structure, Electric and Mechanic(SEM) drawings can ensure that all coordination issues are resolved prior to construction. Construction companies attempt to apply Building Information Modeling (BIM) to manage and integrate engineering information and solutions efficiently into the CSD and SEM processes to enhance the accuracy of design and the efficiency of review. There are several powerful commercial tools, such as Bentley Navigator, Autodesk Navisworks, and Tekla BIMsight, that can review the integrated BIM model and detect conflicts in systems, and allow planners to correct the conflict issues one at a time. However, for increasing numbers of conflicts, this may be inefficient, and requires them to be arranged in a list according to impact and seriousness before solving them. For this reason, this research implements a module for conflict impact assessment based on rule-based reasoning to classify and weigh conflict impact and seriousness, and highlight the conflicted objects in the BIM system in different colors depending on their conflict type and seriousness during the analysis. This system not only detects and lists possible conflicts and errors, but also sorts them according to the severity of impact and conflict type. Planners can effectively modify the BIM models according to these conflicts as they are listed and visualized in the BIM system. If these conflicts, such as pipeline interference and problems of insufficient space, can be avoided in the early stages of planning, it facilitates the achievement of project objectives in quality, scheduling, and cost.

Aug 1, 2013

By David deVries, James Rajith, Paul Mascrenhas, Nurzhan Dyussekenov, Lawrence Hanschar

Kansanshi Copper Smelter commenced operation in March 2015. The smelter features four Peirce- Smith Converters (PSCs) operated in a three hot, two blowing configuration. This paper describes some of the process automation and design features implemented to maximize operational and environmental performance. To ensure that the converters were easy to operate, efficient, and were protected in emergency situations such as power failures or loss of tuyere air supply a significant focus was placed on automated sequences initiated by “one button” operator commands or otherwise automatically by the Distributed Control System (DCS). Examples include: main converter roll-in and roll-out sequences; emergency roll-out in the event of power failure; and the charging sequences for reagents (silica and reverts). Other automated features configured for the PSCs were specifically aimed at maximizing converter capacity and reducing the environmental impact from fugitive emissions. These features include: “one button” in-stack charging; automated restriction of blowing rate based on the available acid plant capacity; and fully-automated control logic for the Secondary Ventilation System. In-stack charging allows anode furnace oxide slag to be poured into the PSCs while the converters are still blowing and still sending off-gas to the acid plant. PSC Secondary Ventilation control logic was configured to require minimum input from the operators while ensuring maximum utilization of the available draft from the ventilation system. Highly automated PSC controls contribute to high utilization, averaging 41.2 in-stack hours per day. INTRODUCTION Kansanshi Copper Smelter (KCS) is located near Solwezi at Kansanshi copper mine in Zambia's Northwestern province. The smelter treats concentrate produced at Kansanshi mine as well as Sentinel mine located 150 km west of Solwezi. Four Peirce-Smith Converters (PSCs) are installed at KCS. The nominal capacity of each converter is to treat 350 t of copper matte and produce up to 250 t of blister copper per batch. Normally three PSCs are hot, with two able to operate (produce off-gas), and the third converter on hot standby. The fourth converter is normally under cold repairs. The blister charge size is relatively low for the matte charged due to the unavailability of tank house or other high copper scrap.

Jan 1, 2019

By Rodrigo Madariaga, Tracy T. Morris

The practice of stripping copper starter sheets from titanium blanks to be used in a conventional electrolytic tankhouse has been around since the advent of Electrometallurgy. Historically it has been done manually, utilizing many people to produce in some cases thousands of starter sheets per day. Some other conventional tankhouses have successfully converted to using mechanical means to strip starter sheets or have made the switch to permanent cathodes and although robotics have been around for quite some time they have not been used to strip starter sheets until recently. The Amarillo Copper Refinery began using robotics to strip several years ago and the details to how this came about and how the robots work will be described. INTRODUCTION ASARCO LLC (Asarco) was organized in 1899 as the American Smelting and Refining Company. Originally a consolidation of several lead-silver smelting companies, it evolved over the years into an integrated producer of primary non-ferrous metals, including copper, lead and zinc and associated co- products (Marcosson, 1949). Grupo México, S.A.B. de C.V acquired Asarco in 1999. Today, Asarco is a vertically integrated producer of primary refined copper and associated co-products such as gold, silver, molybdenum, selenium and tellurium. Asarco operates three open-pit mines and mills and two solvent extraction-electrowinning (SX-EW) plants all in Arizona plus a copper smelter in Arizona and a copper refinery in Texas. Figure 1 illustrates how the copper metal comes out of the ground at the mine and ends up as a refined product at the refinery The copper refinery in Texas is known as the Amarillo Copper Refinery (ACR) and is located in Amarillo, Texas. It was built in 1975 to replace 3 other aging refineries and was designed to produce 550,000 tons (500,000 MT) of refined copper per year using conventional starter sheet technology. At the time it was commissioned it was the largest tankhouse in the world at just under 1/2 miles long under one roof.

Jan 1, 2019

By T. Negeri, M. Boisclair, A. Bouajila

CanmetMINING has been working on process development for separation and concentration of rare earth bearing minerals from various ores. Among others, the flowsheet development for the Montviel Rare Earths/Nb deposit, located at the north end of the Abitibi region in Quebec and owned by GeoMegA Resources Inc. (GeoMegA) is now at an advanced stage. The concentrate produced by a flotation-only process at the early stage of the project accounted for higher than 90% TREO and Nb recovery in 40% mass. This concentrate was submitted to SGS Lakefield for hydrometallurgical processing. Lixiviation of the concentrate using hydrochloric acid yielded approximately 99 % REE. An overall (from ore in ground to final precipitate) REE recovery of 80% was obtained through a series of selective precipitation steps. Recently significant additional developments have been made. CanmetMINING is steadily improving the quality of concentrate produced through a simplified, more efficient flowsheet which consists of flotation, magnetic separation, and a thermal treatment procedure. The paper discusses aspects of the process that allowed obtaining 82% recovery of TREO and Nb in 16% of mass, the best result to-date.

Jan 1, 2014

By Herbert D. Drechsler

"THE FOLLOWING are some comments on the article, ""International Trade in Minerals and Economic Development"", by M. Sengupta, published in the October 1976 issue of the CIM Bulletin.Sengupta says in the introduction that ""The mechanism through which this growth (economic development) has occurred is basic ally straight forward"". His statement is quite misleading and perhaps it is better to quote Gerald Meier:""Development economists must operate in an imperfect second-best world, away from the simplified premises of neoclassical economics. Their subject matter is therefore not yet a coherent or self-contained discipline. Denied recourse to a set of general principles, perhaps the student's most sensible introduction to economic development is through a study of 'leading issues' that are at the time a major preoccupation of the development economist and development practitioner"" .Sengupta quotes an authority who wrote 18 years ago. Academic and operating development economists today know full well that existing theory is quite deficient. Sociologists, political scientists and engineers in this field also know that economic, social, political and technical development involves all academic disciplines.Sengupta indicates that tariffs in developed countries prevent less developed countries from supplying refined metal, or manufactured and semi-manufactured products. He lists Zambia, Chile and Zaire as examples of copper concentrate exporters, as inadequately shown in Table 1. He is wrong."

Jan 1, 1977

By Bergh. L. C.

On line monitoring and diagnosis systems of process operating performance are becoming an important part of industrial programs, leading to improve process operation and therefore product quality over time. In processes, such as the contact section of a sulphuric acid plant, a large number of input variables, highly correlated, are presented. These characteristics usually pose more difficulties in modelling the process for monitoring and diagnosis purposes. Multivariate statistical projection methods, such as Main Component Analysis, have been proposed to effectively deal with these situations. The application of these ideas to a section of a 2350 MTD sulphuric acid plant, located at the Caletones Smelter, including dry tower, gas blowers, catalytic reactor and S03 absorber processes, is discussed here. A PCA model with eight main components is used for monitoring and diagnosis of more than seventy operating variables. Hottelling's T2 and Q residuals test were used for detecting measurement problems in relevant variables, and for identifying which set of variables were responsible for driving the process outside its normal operating region. Furthermore, considerable information for the correction of the tested operating problems was given by the use of these techniques.

Jan 1, 2007

By J. W. Scott, G. G. R. Falkenberg

"The Syncrude project is an integrated complex designed to mine, extract and upgrade bitumen from the Athabasca tar sands to produce 129,000 barrels per day of synthetic crude oil. This paper provides a brief general description of the location, history and geology of the tar sands and the overall organization and structure of the project. The major emphasis and the bulk of the detail presented deals with the extraction plant; a material handling and mineral processing installation designed to treat 312,000 tons per day of tar sand feed.History of the Tar SandsThe Athabasca tar sand deposit was recorded in 1788 by Peter Pond, however the first serious geological mapping and exploration did not begin until 1915. Little interest was taken in the deposits until the Second World War, when the governments of Canada and Alberta conducted an extensive exploration program. In addition a number of pilot plants were sponsored during the 1940 -1950 decade. The hot water separation process was successfully demonstrated on the pilot plant scale during 1948 -49, and was established commercially in 1967 in the G.C.O.S. plant. The Syncrude plant, due to come on stream in April 1978, also employs the hot water separation process."

Jan 1, 1978

By L. Xu, A. Vazirnegad, R. Bhaskar

"Respirable dust samples are collected by the U.S. Mine Safety and Health Administration (MSHA) and mine operators as part of the requirements of the Federal Coal Mine Health and Safety Act of 1969. About 1.85 million respirable dust samples collected by MSHA were analyzed for the period 197/ to 1990 f or the states of Alabama, Colorado, Illinois, Kentucky, Ohio, Pennsylvania, Utah, Virginia, and West Virginia. Trends in coal dust exposure of continuous miner operators, helpers, and roof bolters were analyzed. The reported production in each of the nine states was analyzed. The relationship between average dust exposure and coal production was evaluated. In addition, the differences between mine operator and MSHA inspector collected data were examined for each state. The average exposure levels for the three occupations - miner operator, miner helper, and roof bolter were also compared.The data indicate that the dust exposure levels have significantly dropped over the last twenty years, while at the same time production has increased, attesting to the ability of the U.S. mining industry to adapt successfully to the stringent dust control regulations. In terms of coal production, it appears that some states, such as Utah, Illinois, and Kentucky, were able to increase their production significantly relative to others, such as Pennsylvania and Virginia. The relationship between dust concentration and coal production is, at best, tenuous. 11 implies that existing dust control technology has assisted several mine operators to meet dust standards, while, at the same time, enabling mines to produce more coal than before. Comparison of data collected by MSHA and mine operators indicate that MSHA inspectors recorded higher dust levels and lower shift production relative to mine operators."

Jan 1, 1993

By B. W. Brooks

"After an extensive period of University research and field trials, large scale reclamation of the Waite Amulet tailings discharge areas commenced in the spring of 1978. The Noranda program consists principally of sampling the complete dam to determine the vegetation potential of the various areas, addition of the required amelioration materials, and the use of good agricultural practices. This paper describes the development work that led to the establishment of the Noranda-Guelph Contract and the subsequent findings concerning the revegetation of tailings dams. Current revegetation procedures are presented. INTRODUCTIONThe Amulet Mine Ltd. was staked in 1924 and by 1930 had constructed a small 300 ton per day flotation plant. During the late twenties and early thirties, Noranda Mines Ltd. increased its equity in the company to gain a sixty percent share of this small mine. In 1933 the mine was amalgamated with another small producer, the Waite Ackerman Montgomery Mine Ltd., which was more than eighty per cent controlled by Noranda to form the Waite Amulet Mines Ltd.An interesting historical side point to the story of the Waite Ackerman Montgomery property is that a concentrator was never constructed. In fact, the first ore to go through the Horne mill of Noranda Mines Ltd., built in 1928, was not from the famous upper H and L ore bodies but custom shipments from the Waite."

Jan 1, 1981

By Yu-Min Cheng

Over the past two years, the construction industry has increasingly recognized the benefits and capabilities of building information modeling (BIM) for information integration, visualization and parametric design, reducing the duplication of work and complexity of interface integration, while significantly saving both time and cost. However, due to the variety of participants in engineering projects, the differences between data definition, data format, and data storage increase the difficulty of integrating data from diverse sources. Therefore, buildingSMART has developed a common data schema, called Industry Foundation Classes (IFC), that makes it possible to hold and exchange relevant data between different software applications, to increase the efficiency of BIM work and to ensure a consistent and high-quality output. This paper presents a novel methodology that assists in facilitating the import and export process for parametric BIM objects between heterogeneous BIM systems. This methodology is based on the IFC data schema and includes graphical and non-graphical description data. The objective is to retain the geometry, parameters, unit, texture and links of an object during exchange and sharing to ensure that data integrity is maintained. To sum up, this research addresses the issues of transferring parametric BIM objects between heterogeneous systems to increase data integrity and reduce transfer and integration times.

Aug 1, 2013

By Maria Skyllas-Kazacos

The All-Vanadium Redox Flow Battery that was pioneered and has been developed at the University of New South Wales (UNSW) in Sydney since the mid-1980s is currently regarded as one of the most attractive energy storage systems for large-scale implementation in a wide range of grid-connected and offgrid applications. Several companies are now manufacturing and installing MW-scale VFBs in applications ranging from renewable energy storage, load-levelling, emergency back-up power and power arbitrage. The full-scale uptake of the VRB in commercial energy storage systems however, is heavily dependent on the availability and cost of vanadium used in the VRB electrolyte. Cost is also a function of purity requirements and although there is little scientific evidence on the effect of impurities on the VRB life and performance, VRB developers continue to demand high purity vanadium at considerable cost. This paper will provide a brief overview of the current understanding of electrolyte impurities on VRB performance together with an economic analysis of the impact of vanadium prices on overall VRB capital and levelised costs for a range of applications.

Jan 1, 2014

By E. Ferguson

In evaluating refractory designs for cast house applications, thermal calculations are frequently performed to determine cold face shell temperatures, temperature profiles and metal freeze plane locations within the refractory layer, and heat loss in the steady state condition. A problem arises when looking at molten metal transport crucible designs in that these structures are usually operating under non-steady state conditions throughout their production cycle. Because the molten metal temperature varies with time, and material properties such as thermal conductivity are temperature dependant, mathematical solutions are at best... complicated. This paper presents a relatively simple, iterative solution, that can be set up on a standard computer spreadsheet program, to calculate heat transfer in non-steady state conditions. These calculations can provide curves for (1) molten metal temperature vs time and (2) cumulative heat loss vs time, given variable starting conditions, to aid in the evaluation of molten metal transfer crucible refractory designs.

Jan 1, 2004

By Peter Moon, Lloyd G. Campbell

"How well supervisors supervise, and are supervised determines whether management's goals will be reached and ...how effective the work force will be... Upper management must recognize the potential returns of viable training programs for both management and mine workers… The key to performance, from the standpoint of safety and productivity, is the ability of the line supervisor to manage(1).In this article, the authors will share their experiences in supervisor selection and development. They also draw on the work of two men in particular, Douglas Bray and William Byham, both of whom have contributed significantly to the understanding of supervisory development and training.IntroductionYears ago, there was not much training for supervisors. They worked under an authoritarian style of management and modelled themselves on it. They were generally selected for their skill as miners, mill operators or mechanics. Things have changed. Today, companies have different needs. The selection of supervisors is far too important to rely on guesswork. Progressive companies want supervisors who think like managers - supervisors who know how to plan and organize, set performance standards and monitor them, analyze problems, develop solutions, show sound judgment and deal effectively with people. The evaluation of these supervisory ""dimensions"" is best accomplished through the use of an assessment centre. The Assessment Centre Method increases the accuracy of predicting the future success of candidates being considered for promotion.Mining and other resource companies use assessment centres to select the most suitable people for supervision. The Assessment Centre Method is based on extensive research. It eliminates hit-and-miss selection methods by using several different exercises that simulate the problems and activities that candidates would face if they were promoted into supervision . In other words, they get a realistic "" sample"" of the supervisor's job and are required to deal with and manage interpersonal and problematic circumstances."

Jan 1, 1990