Search Documents

By H. F. Naldrett

"AbstractAt the end of May, 1950, Imperial Oil, Limited, had completed a total of 192 D-3 wells in the Leduc-Woodbend field, 62 of which lost circulation in the D-3 zone for periods ranging from two hours to fifty days. The majority of the remaining wells •lost some mud without actual loss of returns. In addition, independent operators completed 69 D-3 wells, of which 9 lost circulation. Included among the latter is the now well known Atlantic No. 3 well, which blew wild out of control for seven months. The well was finally brought under control through two directionally drilled wells, but not before the derrick fell and the well caught fire. Practically all known filler materials have been used in attempt3 to prevent or regain loss of circulation, but none has been successful, except in minor cases. Ordinary sawdust has come to be the most commonly used filler material and is added to the mud before the D-3 zone is contacted. In cases of serious loss of circulation, the on1y successful method of getting returns has been the use of a series of small cement plugs.IntroductionThe Leduc field is twenty miles southwest of Edmonton, Alberta. Geologically, it is on the east limb of the Alberta syncline, in the homoclinal belt. The main productive zones are in the Upper Devonian formation and are known locally as the D-2 zone and D-3 zone, respectively (see Figure 1).The D-3 zone is a dolomitized reef with fair average porosity and permeability, and shows considerable evidence of vertical fracturing. Porosity is mainly due to moderately uniform development of vugs which are interconnected by small crevices. However, the formation is known to be, locally, extremely vuggy and in places cavernous. These latter conditions create very serious drilling problems due to the hazard of loss of circulation, particularly in the gas cap, which has a maximum thickness of 200 feet. The D-3 zone is contacted at an average depth of 5,300 feet."

Jan 1, 1950

By Ausenco Engineering Canada

"This paper demonstrates the selection of grinding circuit technology for a number of recent projects including discussion of the key drivers and the role of energy efficiency. Decreasing head grades combined with a strong and sustained increase in operating costs has forced miners to examine increased project size, increased equipment capacity and efficiency improvements in order to reduce their unit operating costs and improve overall project economics. Comminution energy consumption, safety and capital cost considerations play a critical role in the success of projects. This paper presents some key guidelines for a successful and cost effective comminution circuit design and includes a case study on three projects, outlining the issues and the drivers which led to the ultimate circuit selection and the critical role that energy efficiency played.INTRODUCTIONComminution circuits for minerals processing are selected based on their suitability and efficiency in reducing run-of-mine ore to the desired feed size for the downstream process. The input material (ore) properties and downstream process requirements are the key determinants and there are standard approaches for each circumstance.The minerals processing industry has been a fast adaptor of efficiency improvements based on increasing capacity of equipment (e.g. trucks, crushers, mills, pumps) but less successful in adapting radically new technologies that disrupt incumbent flowsheets or processes.The installed power of grinding mills has increased linearly over the past 25 years (Meka & Lane, 2010) and pumps and classification equipment have kept pace. The autogenous grinding (AG) and semiautogenous grinding (SAG) mills displaced stage crushing as a dominant method of coarse rock breakage in many applications causing crusher manufactures to increase the capacity of cone crushers to meet the competitive demand.Examples of new comminution technology in the 20th and 21st centuries are the development and adoption of cyclone classification in the 1940s (Newtech, 2016), AG milling in the late 1950s, vertical grinding mills in the 1980s, high pressure grinding rolls (HPGRs) also in the 1980s and ultrafine milling technology in the 1990s (Meka & Lane, 2010)."

Jan 1, 2016

By K. Harris, J. B. Wahl

Ni-base superalloy cast materials provide an outstanding balance of high temperature strength, fatigue resistance, oxidation resistance and coating performance and can be produced to very tight tolerances in extremely complex configurations, such as axial and centrifugal integral cast turbine wheels. As a result, cast superalloys are used in the most demanding applications of aero and industrial gas turbine engines. Use of these materials is expanding to smaller microturbine, turbojet, turbocharger and missile engine applications due to this unique combination of desirable properties. This paper will present an overview of the application of investment cast Ni-base superalloys and process capability to small turbine and missile engines.

Jan 1, 2010

By J. E. Ryan

General Description Due to the extreme cold weather experienced in Flin Flon during the winter months, thought and precaution were necessary in the design of the plant buildings. The machine shop, carpenter shop, drill shop, and coal plant buildings are similar in the building materials used in their construction. They are sided with two-inch shiplap, insulated with celotex and asbestos paper, and covered with corrugated iron on all side-walls. Roofing consists of 2 by 4 lumber on edge, laminated, and further covered by celotex and three-ply roofing. These buildings are heated by means of unit heaters. The heaters are primarily steam-heated radiators, through which the air of the buildings is circulated by electrically-driven fans. Our machine shop is located to the east of, but central to, the main operating buildings of the mine and plant, and is so connected by a net work of tracks as to be able to serve all portions of the entire plant conveniently. The building is divided into two bays, the main bay 53 ft. by 340 ft., and the east bay 24 ft. by 340 ft. The shop office and drafting room, a two-story annex 24 ft. by 30 ft., is located on the west side of the shop. The arrangement within the shop is such as to house conveniently the several departments, namely, heavy machine tool section, repair floor section, boiler shop heavy tool and floor section, blacksmith heavy tool and forge section, tool room, electric welding rooms, stock room, tin and copper shop, and electrical parts and armature winding and repair shop (see Figure 1). All the heavy tools, the repair floor section, and railway tracks are so located in the large open bay as to be fully serviced by an electrically operated 15-ton bridge crane, with a span of 50 feet and a travel the full length of the shop. A standard-gauge railway track, branched off the main line, penetrates the full depth of the building. This track lies along the extreme east side of the main bay, allowing easy entrance and movement of rolling stock and heavy machinery, loaded on standard flat-cars, to the repair floors in the main bay. Eight jib cranes, affixed to building columns, further facilitate the heavy repair work throughout the various shop divisions. Our light and heavy machine tools are standard equipment, not unlike tools used in mine, mill, and railway shops.

Jan 1, 1935

By L. S. Almeida, U. A. Courbassier, C. T. Guimãaraes, M. N. Souza, V. L. Silva, H. P. Dias, G. A. Bicalho, B. S. Rocha, P. N. Rodrigues, A. Carnevale

During primary aluminum production the anode changing is a very important task. So improvements on it will be essential to avoid disturbance and have a better operational control. After anode changing a good current distribution will be guaranteed using a cavity cleaner and precise anode setting. Albras switching a manually anode setting to an automatic one solved the setting problems. In this paper it will be shown some pot line results and the improvements on workers ergonomic and safety conditions. The device was developed in a partnership between Albras and Pesto.

Jan 1, 2006

By A. M. Bell

General Summary THIS paper attempts to describe in a preliminary and general manner the nature of certain copper discoveries now being developed by Gaspe Copper Mines, Limited, in Holland township, in the interior of the Gaspe peninsula. Some copper mineralization appears to have been known here at the time of the earliest French explorations, was rediscovered in 1921, and has been under intermittent development by Noranda Mines since 1938. In the last two years discoveries have enhanced the picture so that the deposit now promises to develop into one of the important Canadian copper producers. As ideas are constantly changing with continuing development, any picture given now is very partial and tentative and must be subject to future revision. The nature of these copper occurrences differs from others known in eastern America. In many respects they have unique features but they are most closely akin to some copper deposits found away from the intrusive rocks in the porphyry copper districts of the western United States. The most important orebodies are replacement deposits in a limestone horizon in which the ore gangue is converted to skarn. These lie at considerable distances from any known intrusive but seem to have been derived from a buried stock of granite that intrudes the sedimentary rocks of Lower Devonian age. This intrusive has produced alteration effects in the overlying rocks that may afford a key to locating other ore areas in the Peninsula.

Jan 1, 1951

By J. A. Finch

Individual mineral cyclone performance curves were determined for the four major minerals at two lead-zinc concentrators. Sizing was by screen and cyclosizer down to approximately 10 um, with lead , zinc and iron as saying of each size fraction. The performance curves were similar in shape and located according to the mineral specific gravity, Pm. The curves displayed a discontinuity at the fine end and a magnitude of short-circuiting of fines to the underflow which increased with Pm. Mass fraction of water to the underflow was only a guide to this short-circuiting. Sharpness of separation seemed in dependent of Pm. An inflection in the over-all performance curve was shown to be a consequence of the individual component mineral performance. A general relationship was observed showing that the flow regime of classification changed from laminar/ intermediate to turbulent with increasing cyclone feed size. Individual mineral size reduction for the four major minerals at one of the concentrators was also determined. Size reduction of the silica was greater than that of the galena, in contradiction to their accepted relative grind-ability. The observation did correlate with silica being much coarser than the galena in the feed to the ball mill. It is suggested that the silica acted as a buffer to the galena.

Jan 1, 1977

By Jamal Jafari, Abbas Sam

"The concentration of the fourth production line at Golgohar includes 66% iron with Blaine number of 500 cm2/g. For pelletizing process, the feed iron grade should be greater than 68% with minimum Blaine number of 1800 cm2/g. In this study, the low intensity magnetic Separators, particularly the feed particle size distribution of LIMS were considered. The feed particle size distribution of the separators was optimized to prepare an appropriate concentrate (as mill pelletizing feed). The samples were performed from the LIMS feed and after grinding, four d80 (64, 103, 132, and 15 3µm) were prepared. Then, laboratory magnetic separation experiments were conducted on these samples. The best results obtained using d80 of 132µm. In this particle fraction, the iron grade and Blaine number were 70.3% and 1571 cm2/g, respectively. Therefore, it seems necessary to include a grinding and classification systems before LIMS stage. According to the presence of a high amount of -132 µm particles in the initial feed, an inverse closed circuit was selected. The hydrocyclone was designed in three units as the classification system with 62 cm (diameter), 22 cm (overflow outlet) and 11 cm (apex diameter). By simulation of hydrocyclone with USIMPAC software, the size distribution of underflow was determined. Based on these results, a ball mill with dimensions of 6.7 m (length) and 5 m (diameter) was designed as grinding system.INTRODUCTIONGole-Gohar iron ore concentration plant No.4 (Polycom Plant) in Gole-Gohar Industrial and Mining Complex was installed to increase production capacity as well as treating the circulating load from AG and SAG mills of the main concentration plant of the complex. The load from the mine is crushed using jaw and cone crushers. The crushed ore is then combined with the circulated load and the combination is then grounded using HPGR and ball mills respectively.After comminution, there is a magnetic separation plant which includes a medium intensity magnetic separator (MIMS) followed by three low intensity magnetic separators (LIMS). Final concentrate dewatering is done using three belt filters. After the primary magnetic separation, the ore is upgraded to 62% Fe content and final concentrate which is the product of LIMS has 66% Fe content."

Jan 1, 2016

By Alfred C. Lane

Reference to the original use of the terms Laurentian and Huronian (and its extension), shows that the former was applied to granitized sedimentary and metamorphic pre-Cambrian rocks, and the gneissoid igneous rocks associated therewith, and the latter to non-fossiliferous rocks supposed to be later. But it appears from the work of Collins, Quirke and others that there is more or less of an overlap, and that of the original Laurentian the Grenville limestone, and some of the granites, may be later than the lowest part of the original Huronian. Before we can decide whether to abandon one or the other of the two terms, or how to delimit them, it is important to know the extent of this overlap. The Pb :U ratio, though not to be depended upon too minutely, does give a real idea of the age of a mineral as it increases with the decay of uranium, and so is greater the longer the time since the uranium was separated: and there are reasonable prospects of help there from in getting a knowledge of the relative age of different granites to assist in solving the problem, as facts already collected show. 1. Historical review of the use of the words Laurentian and Huronian: 2. Difficulty encountered: 3. Popular account of atomic disintegration: 4. Methods of estimating age by it: 5. Applications.

Jan 1, 1925

By D. A. Jacobson

Mining operations, whether new or existing, are constantly looking for ways to maximize production and improve energy efficiency, while keeping the footprint required to a minimum. The Nordberg MP1250 cone crusher was designed with these three goals in mind. A series of side-by-side evaluations comparing an MP1250 to an MP1000 were completed at two Freeport-McMoRan operations. The first evaluation began October 2009 in a tertiary position and the second began March 2010 in a secondary position, where it remains in full production today. Utilizing 25% higher power capacity than the existing MP1000 tertiary crushers, the MP1250 had 29% higher capacity and 17% lower specific energy, adjusted for differences in feed and product size. The MP1250 compared to the existing MP1000 secondary crushers achieved 30% higher capacity at a slightly reduced specific energy, while achieving a finer product. The MP1250?s higher capacity and energy efficiency may have application in many crushing plants. Depending on site specific economic factors, greenfield projects may benefit from a smaller footprint and less ancillary equipment, whereas brownfield projects may benefit from higher capacity or a finer product within the same footprint.

Jan 1, 2012

By JOHN H. HUDSON

Ceramic clays of the Prairie Provinces range in age from Lower Cretaceous to Pleistocene and Recent. Two significant ceramic clay horizons are the Paleocene Willo wbunch Member of the Ravenscrag Formation in Southern Saskatchewan and the Upper Cretaceous Whitemud Formation, which is found in Saskatchewan and Alberta. The Willowbunch Member is worked at one locale in Saskatchewan; the Whitemud Formation is worked at several locales in Saskatchewan and Alberta. Bentonite operations are found at Morden in Manitoba, Rosalind and Onoway in Alberta, and Wilcox in Saskatchewan.

Jan 1, 1984

By Robert Marchand

_ North-western Quebec _ Bousquet mining district _ 21 M oz mining camp _ 100,000 t/yr (400 t/d) _ Shrinkage : 52 % _ Longhole : 40% _ Development : 8% _ 5 days/week _ 120 employees _Discovered in 1936. _12 changes of ownership. _Exploration & development : 1987 _Commercial production : 1990 _Shaft deepening : 1995 _Internal shaft : 1999

Oct 1, 2001

By Lionel C. Piuze

Introduction and Early History The British Canadian Mine is one of four operating properties of Asbestos Corporation, Limited, and is located in the town of Black Lake, Que., five miles southwest of Thetford Mines. In the early days of as1bestos mining, this .property was owned by a few small companies who later became part of the Asbestos Corporation. First .to commence mining operations on the property was the Coleraine Mining Company who, in 1885, began selling part of their large holdings in the area to various asbestos mining interests. Of these, the earliest active companies were Manhattan United Asbestos, the Glasgow and Montreal Asbestos Company, and the Anglo-Canadian, the last named later becoming the Standard and Dominion Asbestos Companies. Extraction of fibre was limited to what is now known as crude asbestos and the methods were primitive. Drilling was done .by hand and the ore was lifted by derricks operated by band winches. These were later replaced by horse power, but it was not until 1887 that the first steam-operated boom derricks were introduced, at the Anglo-Canadian mine. The ore was hand cobbled and the asbestos roughly classified and bagged. The waste rock, which by today's standards contained a considerable percentage of marketable fibre, was dumped near the pit. The first attempt to separate the asbestos from the host rock by mechanical means was made in 1888 by the G1asgow and Montreal Asbestos Company, then known as the Scottish-Canadian Asbestos Company, whose mill, erected in that year, was the world's first asbestos mill. Though the equipment was crude, the principles employed were the same as those used today with much larger units. The next steps were the use of rock drills, the adoption of steam rail transportation for moving mill rock, and conversion to the more flexible cable-derrick hoisting.

Jan 1, 1950

By G. R. Cope, J. S. Getsinger, K. D. Lund, T. Neale

"Mineral exploration in the Sicker Group, a belt of Paleozoic volcano-sedimentary rocks on Vancouver Island, has traditionally centred on auriferous polymetallic volcanogenic massive sulphide deposits such as those currently mined by Westmin Resources Ltd. near Buttle Lake. Recently, however, the focus of exploration in the Sicker Group has shifted toward targets of structurally controlled gold concentrations, with notable success. Major north and northwesterly-trending structural features such as the Cowichan-Horne Lake break (one of several regional high-angle thrust fault s active throughout a long period of geological time) and related fault systems have contributed to localization of gold mineralization.Using the extensive information database compiled by MPH Consulting Limited during numerous exploration projects in the Sicker Group, two cross sections through areas with significant gold occurrences southeast of Port Alberni are presented. The cross sections combine geological, geochemical and geophysical data in an attempt to emphasize the relationship between structural trends and gold mineralization. Examples from specific properties, including gold discoveries along the Mineral Creek fault zone, are used to illustrate this relationship."

Jan 1, 1990

By D. Warkentin, T. Yeomans, R. Tavakoli, A. Nacu

"One of the most successful commercial methods of extracting gold from ores involves solubilizing gold as a gold cyanide complex, followed by adsorption of the complex onto activated carbon. The gold cyanide is subsequently eluted from the carbon to produce a concentrated gold solution suitable for electrowinning to recover the precious metals. Stripped carbon is treated in a kiln under a flowing steam atmosphere to reactivate its surface, allowing it to be reused. The aim of this study was to investigate the gold elution using a mixture of sodium hydroxide and isopropyl alcohol in both batch and continuous tests, with the eluates being electrowon on carbon foam cathodes. The effects of various factors, including alcohol content and sodium cyanide addition were studied. The addition of alcohol considerably improved gold elution kinetics, while the presence of sodium cyanide did not have a significant impact on either elution efficiency or kinetics. In all cases, efficient electrolysis was shown to be an important factor in maintaining effective carbon circuit operation.INTRODUCTION Gold dissolved as Au(CN)2- complex during cyanidation is recovered either by cementation with zinc powder, also known as the Merrill-Crowe process, or by adsorption into activated carbon through Carbon-in-Pulp (CIP) or Carbon-in-Leach (CIL) processes. Activated carbon loaded with gold is then eluted and gold is subsequently recovered by electrochemical methods. Conventional elution processes such as atmospheric and pressurized Zadra processes, involve stripping with a cyanide (0.1–0.2% NaCN) and sodium hydroxide solution (1–2% NaOH) at high temperature (90–140°C) over long elution times of 8 to 72 hours. In the Anglo American Research Laboratories (ARL) elution process, the acid-washed loaded carbon is pretreated with a strong sodium cyanide and sodium hydroxide solution (1–5% NaCN and 1–2% NaOH), followed by elution with water at 110–130°C. Solvent-assisted elution processes have also been reported, such methods use varying concentrations of alcohols (methanol, ethanol and isopropanol), ketones, or glycols to enhance atmospheric elutions at temperatures up to 95°C (Muir et al., 1985; Ubaldini et al., 2006; Espiell et al., 2008; Soleimani & Kaghazchi, 2008). The present work investigates the efficiency of isopropanol in the gold elution process, as well as the methodology of evaluating gold stripping processes in the lab setting"

Jan 1, 2017

By L. Gonzalez-Sardi, W. McCombe, M. Pearson

Pressure oxidation is increasingly being used for processing refractory sulphide ores and concentrates because it offers highly effective base metal and precious metal extraction while minimizing elemental sulphur, arsenic & mercury emissions. Yet pressure oxidation processes introduce new safety concerns and process risks as demonstrated by a number of safety incidents over the last 20 years, including overfilling, oxygen-metal fires, nozzle/sparger failures, and uncontrolled pressure relief events. Chemical Process Safety regulations in the United States and Canada mandate that companies constructing or operating chemical process facilities perform a rigorous hazard and risk analysis based on either ANSI/ISA-84.00.01 or IEC 61511 safety standards to determine the level of protection required for each hazard in the plant. This paper describes the application and implementation of three (3) unique safety instrumented systems developed by Hatch for ensuring the safe operation of three different pressure oxidation processes.

Jan 1, 2014

By M. Turner-Jones, N. Steenekamp

"The Lonmin Base Metal Refinery treats converter matte from the Lonmin Smelter to produce nickel sulphate crystals, copper cathode as well as a concentrate containing the platinum group (PGM) metals. The original process employed a Sherritt design and utilizes atmospheric and pressure leaches for the dissolution of base metals. This paper describes the original flow sheet and the improvements made to enhance PGM recoveries, product quality and to increase capacity. Changes include the introduction of flash recycle cooling on the autoclave, batch leaches to improve the quality of the PGM concentrate and the implementation of solid-liquid separation with centrifuges. INTRODUCTIONThe Lonmin Base Metal Refinery (BMR) is about 100 km north-west of Johannesburg and treats converter matte from the Lonmin Smelter to produce nickel sulphate crystals, copper cathode and a concentrate containing the PGMs. The plant was commissioned in 1985 based on a Sherritt design to treat 12 tonnes converter matte per day. The original flow sheet consists of a milling circuit, an atmospheric leach and a pressure leach to produce a PGM concentrate which is despatched by helicopter to the Lonmin Platinum refinery in Brakpan, about 40 km east of Johannesburg. The liquor from the atmospheric leach is treated by crystallization to produce a nickel sulphate hexa-hydrate crystal. The leach liquor from the pressure leach is treated by a selenium removal step followed by electro-winning to produce copper cathode. The spent solution from the copper electro-winning is recycled to both the atmospheric and pressure leach steps to provide sulphuric acid for the leaching reactions.Modifications were made to the original circuit to increase the plant capacity, to improve the PGM recoveries and to improve the quality of the PGM concentrate. Capacity increases included all the unit operations, new mill, new first stage, additional autoclaves, additional nickel sulphate crystallizers, new copper electro-winning and new batch leach reactors for upgrading the PGM concentrate. The current circuit is described in this paper and not the detailed history of each plant change."

Jan 1, 2012

By K D. Conroy

For the past year, Lowphos Ore Ltd. has been operating two desliming hydroseparators on a fully automatic basis. Automatic operation is achieved by sensing the position of the silica-magnetite interface and automatically controlling the jet water addition to maintain a desired interface position. The system further provides automatic control of the underflow pump speed in order to assist in maintaining interface position when an <Ore change occurs. Interface position is maintained at 12 inches below the surface and is -controlled within plus or minus one inch. Metallurgical unit recovery is held above 98.5 per cent, and a 10 to 12 per cent increase in concentrate grade is normally achieved.

Jan 1, 1963

By P. P. Rosario

A research project was conducted at the University of British Columbia (UBC) resulting in the development and evaluation of a novel comminution circuit incorporating autogenous grinding and parallel trains of cone crushers and high-pressure grinding rolls (HPGR). A primary driver for the circuit was to treat ore from deposits with clay and variable hardness. This paper summarizes the unique pilot-plant test program that was developed as a basis for experimental simulation and lists the main findings of the research, including the circuit?s potential operational cost savings compared to a conventional SAG circuit.

Jan 1, 2012

By Tapio Leskinen, Jouko Koskinen, Timo Nlltti, Lappalainen Seppo, Pentti Vanninen

"The Courier 300 on-stream analysis system manufactured by Outokumpu has now been in operation at five of the company's concentration plants long enough to give a reliable basis for closer examination of the benefits achieved in control of these processes. The first system was installed at the Pyhiisalmi mine at the end of 1967. Since November 1970, two analyzers have been in operation at Pyhiisalmi feeding the assay data to a process computer which controls the whole plant and does the optimization of the process. In October 1970 the Courier 300 analysis system was installed at S. T. O. LESKINEN J. KOSKINEN the Keretti concentrator of the Outokumpu mine, followed soon by installations at the Vihanti Mine in May 1971, at the new Vuonos mine in November J 971 and at t he Kotalahti mine in December 1971. Since installation of the Courier analysis systems, considerable improvements have been achieved in the control and the economy of the plants. Immediate knowledge of the changes in the process and the possibility for rapid action has resulted in evener production and higher capacity and recovery. The recovery has been increased most significantly at the Vihanti concentrator, which operates on a complex ore. Consumption of chemicals has been reduced at all concentrators. Due to the fact that process control and partly also bilance analysis are not achieved by conventional methods any more, it has been possible to reduce the personnel of the laboratories drastically. Two of the plants, viz. the Pyhiisalmi and the Vuonos concentrators, are computercontrolled. The Vuonos concentrator started operation in January 1972 under computer control from the very beginning. The Pyhiisalmi concentrator has been computer-controlled since 1970. The Courier 300 analysis system was described in detail at the AIME Centennial Annual Meeting (1971). In this paper, less attention is paid to the analysis system. Only the sampling system of the Courier 300 is described in more detail. In the development of sampling equipment, effective use has been made of the company's wide knowledge of the problems involved and the test field offered by its concentrators. The sampling equipment includes secondary samplers and six basically different types of primary samplers, with which most sampling situations can be managed."

Jan 1, 1973