Search Documents

By A. Grimod

Rockfall drapery systems are commonly used as a simple, fast and cheap measure against the rock falling trajectories affecting very steep slopes. The system basically consists of a steel mesh, which is held on the top edge with a longitudinal cable fixed by means of a suitable number of anchors. The effect of this kind of intervention is to control the falls of the rocks, which are driven toward the bottom with slow velocity, or are stabilized on place. It can be used on any kind of slope to protect sensitive target in the mining industry, roads and railways, and inhabited areas. The falling blocks, typically smaller than 0.6 - 1.0 m in diameter, pile up into a trench (or into a ?pocket of mesh?) at the bottom. In comparison to other types of rockfall interventions, the simple drapery is cheaper, and its maintenance is easier, but on the other hand it cannot be considered the remedy for shallow instabilities, because it can only mitigate the effect of the falling trajectories. The design of simple draperies requires the analysis of several factors like the slope features (height, gradient, morphology), the geological and dynamic features (nature of the ground or rock, type of instability, erosion problem, blocks size), the environmental condition (presence of vegetation, aesthetical problem), the installation problem (accesses to the slope, safety for the workers, safety for the surrounding areas) and finally the performance required (temporary or permanent intervention, required maintenance, cost). Finally the most problematic design-step is the choice of the suitable mesh, the top longitudinal cable, and the top anchors type. Because of the highly variable nature of rockfall behaviour these structures cannot be standardized, but they have to be analyzed and designed for each case. Maccaferri has developed a new software application (MacRO 2) has a practical tool to define the mesh and the related supporting structure composed by up-slope cable and anchors. The software, based on the approach proposed by Muhunthan B. et al. (2005), allows designers to verify the top longitudinal cable, the anchors, and the mesh drapery, and to plan for maintenance procedures. Even if the method seems quite simple and rough, it is effective and lets the designer correctly foresee the materials and the geometrical features to be used on the interventions. This paper analyses the condition for the simple drapery installation, the main steps for the calculations, and it will present a case study in a U.S. mine. Nevertheless, even if the software allows a quick and simple calculation approach, onsite observations are always recommended in order to achieve a good design, with the ultimate goal of protecting property and human lives.

Aug 1, 2013

By William E. Roscoe

"Valuation methods are well established for mineral properties with production or imminent production, and include discounted cash flow and comparable transactions. Valuation methods for non-producing mineral properties, however, are more subjective. Non-producing mineral properties include those at various stages of exploration, properties at the prefeasibility or feasibility stage, properties with currently uneconomic mineral resources, and past-producers. Different valuation methods may be appropriate for different types of mineral properties.Income approach methods such as discounted cash flow and option pricing are generally not applicable to properties at the exploration stage. The market approach is generally appropriate to all types of mineral properties, although it is difficult to find good comparables because of the unique nature of mineral properties and the small number of transactions. Cost approach methods, such as appraised value and geoscience factor, are commonly used for exploration stage properties.Canadian standards and guidelines for valuation of mineral properties are in the process of being finalized by a Special Committee of the Canadian Institute of Mining, Metallurgy and Petroleum (CIMVal Committee). The CIMVal Standards are intended to be consistent with National Instrument 43-101, which sets regulatory standards of disclosure for mineral projects, and with International Valuation Standards. The intent of the CIMVal Standards and Guidelines is that mineral property valuation be carried out by appropriately qualified individuals and that all relevant information be disclosed."

Jan 1, 2003

By Sarah Bélair, Denis Beltrami, Valérie Weigel

"Mabounié is a polymetallic deposit in Gabon containing niobium (1.2%), tantalum (0.03%), rare earth elements (REE) (1.4%) and uranium (0.03%) that are mostly carried by Pyrochlore minerals. Classical route for niobium recovery is a pyrometallurgical process that consists in pyrochlore flotation, dephosphorization of the niobium concentrate and aluminothermy to obtain ferro-niobium. Pyrochlore concentrates can also be treated by a hydrometallurgical process with a mixture of sulfuric and hydrofluoric acid leaching followed by solvent extraction to separate niobium and tantalum. However, the first process does not allow recovering REE and the second one is not environmentally friendly because of the use of HF.ERAMET is looking for new opportunities on strategic metals market and has recently developed a hydrometallurgical process for the recovery of all these metals based on a sulfuric acid treatment of the ore. After solubilisation of the valuable elements, niobium / tantalum are precipitated as a concentrate (12% w/w Nb and 0.3% w/w Ta) while REE (2.7 g L-1) and uranium (90 mg L-1) remain in solution. Nearly 90% of REE are recovered from the solution by conventional REE double salt precipitation [NaREE(SO4)2.xH2O) method but some REE still remain in solution as this method does not allow to quantitatively recover medium (Sm, Eu, Gd, Tb, Dy) and heavy (Ho, Er, Tm, Yb, Lu, Y) rare earth elements. From the different process routes studied (solvent extraction, precipitation, ionic exchange etc.), an innovative method has been developed and patented to recover REE residual concentration in solution. This is based on an aluminum removal step followed by precipitation of REE as REE phosphate concentrate (REEPO4) by phosphate addition into solution. The phosphate concentrate is then purified according to the conventional monazite treatment, i.e. caustic conversion and REE solubilisation in acidic media."

Jan 1, 2016

Orebodies of the Renison Bell - Mt. Bischoff tinfield in Tasmania are stratabound, conformable lenses of massive cassiterite-bearing pyrrhotite, with underlying discordant, fault-fracture-controlled and more siliceous ore. The deposits occur in eugeosynclinal, trough-deposited sedimentary and mafic volcanic rocks which are stratigraphically equivalent to diff erentiated volcanic rocks that contain volcanogenic massive base metal sulphide deposits in a parallel arc to the east. Textures of the massive pyrrhotite ore suggest that it has undergone metamorphic recrystallization. Although the massive ore contains both monoclinic and hexagonal pyrrhotite, a study of a few samples from one orebody suggests that their distribution is stratigraphically controlled, with the monoclinic variety abundant only at the base. The distribution pattern of rare-earth elements in massive ore is similar to that of volcanogenic massive base metal sulphides in New Brunswick, and suggests that mixing of sea water with exhalative hydrothermal brines occurred during ore deposition. Tin is a common accessory element in many volcanogenic massive base metal sulphide deposits providing strong evidence that it, too, is transported and deposited by volcanic affiliated hydrothermal brines. Sedimentary rocks containing the massive orebodies are fine grained, thinly laminated, compositionally banded and of mixed chemical sedimentary-tuffaceous origin. They include finely recrystallized chert, carbonate-rich and pyritic varieties; and soft sediment deformation structures in these rocks suggest that dense sulphides deformed underlying, less dense chert prior to lithification. Close to ore the chert becomes massive and coarsely recrystallized, as does the carbonate, which is here strongly enriched in Fe and Mn. Apatite is present in pyritic, cherty and carbonate-rich beds and in the ore itself, in all of which it shows a similar pattern of rare-earth element distribution, suggesting that it is of marine sedimentary origin. These deposits have traditionally been considered as epigenetic replacements of favourable carbonate horizons by hydro thermal flu ids derived from later Devonian porphyritic intrusions. Some of these intrusions have associated tinbearing greisens. The above relationships suggest, alternatively, that, like massive base metal sulphides, the tin deposits were of original syn-sedimentary origin. Circulating hydrothermal brines generated during early Cambrian eugeosynclinal subsidence and tectonism rose through steep fault-fractures, there giving rise to the discordant orebodies, and were discharged on the sea floor, where the massive pyrrhotite lenses were precipitated with the associated cherts and carbonates. In some places, Devonian intrusions remobilized the earlier deposits, forming greisens and newepigenetic veins. Finally , the geologic selling of these deposits, in trough deposited sedimentary and mafic volcanic rocks, suggests another favourable environment for massive sulphide exploration which is quite different from the domal felsic volcanic environment so heavily favoured currently in North America

Jan 1, 1979

By R. Anthony Hodge

1. Today?s Reality: Voisey?s Bay EIA Activities of the Canadian Environmental Assessment Agency The Tulsequah Chief Decisions The Bank of Montreal The World Bank World Business Council on Sustainable Development The Government of Canada Many company policies

May 1, 2002

By A. Mazhary

"Although sensor-based ore sorting has gained significant attention recently, sorting gold deposits still face a high level of skepticism by gold mining companies. In order to shed some light on the matter, this article looks at two different gold deposits that were examined using X-ray Fluorescence, Electromagnetic and X-ray Transmission sensors. The heterogeneity of each sample is measured based on the assay results of each particle and is related to its sortability. Multivariate linear regression analysis was also performed on the XRF results to find potential proxy elements for detecting gold. The results from these deposits were varied and each sample showed different levels of sortability. While both X-ray sensors proved efficient for different deposits, the electromagnetic sensor failed to produce any promising results. Despite unsatisfactory result for one sample, this technology can have significant advantages in terms of lowering the operational costs and improving head grades and recoveries providing that the deposit is amenable to such separation methods. Therefore, it is important to mention that sensor-based ore sorting is ore and sensor dependent, and as a result, it cannot be applied and be beneficial to all deposits. Therefore, amenability tests are required in order to examine the potential for sensor-based ore sorting before one can reject the idea.INTRODUCTION Although sensor-based ore sorting has gained significant attention recently, sorting gold deposits still face a high level of skepticism by gold mining companies. Except for a few cases presented previously, no new case studies have been published. Previously, mines such as Kloof Gold Mine in South Africa used an optical sorter to sort their waste stockpile in 2003–2004 (Von Ketelhodt, 2009) and then again in 2009 (Von Ketelhodt, Falcon, & Falcon, 2011). More recently, Coeur Operations utilized an XRT sorter for their Kensington Mine in Alaska (Lasley, 2014) and also Anglo-American Platinum used an XRF sorter to pre-concentrate Platinum Group Metals through an algorithm that used chrome, copper and nickel as proxies (Rule, Fouchee, & Swart, 2015)."

Jan 1, 2017

By A. Galley, R. Tosdal, F. Robert

The Canada Mining Innovation Council (CMIC) Exploration Innovation Consortium developed a 10-year business case for developing new discovery criteria, exploration techniques, and better data management and analysis to improve exploration success in deep, remote, and covered terrains. Within this context, the CMIC devised a five-year project proposal to create improved multiparameter exploration tools to detect ore systems and more efficient vectoring toward high-grade mineralized cores. The Footprints project was approved March 2013. More than CAD$13 million funding was provided through the CMIC-led joint sponsorship from 30 companies and the Natural Sciences and Engineering Research Council. Consistent industry leadership and integration of dedicated industry and academic expertise has the project on track for reaching its well-defined objectives.

Jan 1, 2014

By C. H. Knight

"THE OBSERVATIONS that follow are confined to simple wet cyclones such as the cylindro-conical unit developed by the Dutch States Mines and marketed in America under the trademark 'Dorr-Clone'. Energy to do the work comes from the inlet velocity of the feed slurry, which is usually pumped' to the unit by a centrifugal pump.Such cyclones are simply classifiers of enormous capacity and depend for their separating effect on differences in rates of particle settlement. These particle settling rates, of course, vary with particle size, particle density, particle shape, pulp viscosity, and pulp density.The dilution of the overflow product affects both pulp viscosity and pulp density. In most operations, the temperature and the composition of the liquid -hence its viscosity --are fixed, but both pulp viscosity and pulp density can be changed by changing pulp dilution.Since the separating effect depends on differences in rates of particle setting, a perfect split with 100 per cent of the particles coarser than a given size in the underflow and 100 per cent of the finer sizes in the overflow is not possible. Just how far the separation departs from this perfection can be calculated rather exactly from the following principles, which also apply to mechanical classifiers. In removing or settling out of the overflow product all particles up to a specified size, some of the finer particles must settle out simultaneously."

Jan 1, 1955

By S. Kaiman

This paper describes flotation test work conducted over the past several years at the Mines Branch, Ottawa, on the radioactive quartz-pebble conglomerate ores of the Elliot Lake area of Ontario. The purpose of this work has been to produce a uranium flotation concentrate for sub-sequent leaching operations. The results of earlier investigations are summarized and correlated with the results of mineralogical studies of the ores and flotation products. The results of recent pilot-plant investigations by flotation, as well as by gravity concentration followed by flotation of the gravity tailings, are given. The principal collector used for uranium flotation was a tall oil fatty acid, and the indicated total cost of all reagents ranged from 21 to 31 cents per ton of ore treated.

Jan 1, 1966

By S. Vongpaisal, T. R. Yu

"A set of new blast damage criteria has been developed, with special reference to blasthole mining operations, for assessing damage by incorporating the vibration level, rock properties, site characteristics and the effects of ground support systems. The main objective of this work was to provide a database with reasonable accuracy for use in optimizing blast design, numerical analysis and ground control expert system module development.The new damage criteria allow one to estimate the degree of damage to rock structures in terms of a dimensionless parameter defined as Blast Damage Index (BDI). This allows for the description of blast damage in a unified form, and facilitates the development of codes for numerical modelling to express the degree of blast damage universally. A number of field investigations from several stope production and slot opening blasts at a large underground base metal mine were carried out to verify the developed index. The results show a good correlation between the observed damage and the type of damage predicted from the BDI values.Practical measures are also provided for minimizing blast damage in large underground blasthole mining operations"

Jan 1, 1996

By F. P. Morawski, J. E. Schelske, J. R. Geddes, B. R. Eberts, D. M. Wilson, J. D. Jeffries

"The Griffith Mine is located 200 miles northeast of Winnipeg and is 30 miles south of Red Lake, Ontario. Owned by The Steel Company of Canada Limited and managed by Pickands Mather & Co., it has an annual rated capacity of 1.5 million tons of high-grade iron ore pellets with an analysis of 66.3 per cent iron and 4.5 per cent silica.Development of the mine and construction of the plant got underway in January of 1966 and operations began in February of 1968. The orebodies outcrop on the shore of Bruce lake and run under the lake. The ore in its crude form is a metasedimentary low-grade magnetite and occurs in a highly folded banded formation. The average iron analysis of the crude is 29 per cent and the over-all weight recovery is 32 per cent.In order to mine the portion of the orebody under the lake, the soft varved clay on the lake bottom was hydraulically dredged and a dyke constructed of rock, with till used to provide an impervious seal on the lake side of the dyke, prior to dewatering.Mining is carried out by conventional open-pit tech-niques. Ore dressing is achieved by combining one crushing stage and a two-stage grinding system, with beneficiation by magnetic separation, hydroseparation and flotation. Agglomerating is done with conventional balling drums and pelletizing is carried out in shaft furnaces.Of interest and discussed in detail are the 32-foot autogenous cascade mills ."

Jan 1, 1970

In the last five years, new iron ore pellet plants have been built with significantly reduced air pollution levels compared to the older generation of plants. European and American pollution controls are more stringent that in China and Brazil. The recent American plants have successfully employed circulating fluidized beds for sulfur control, baghouses for particulate control, activated carbon injection for mercury and a new design of specialized low-NOx burners.

Jan 1, 2015

By G. Kolosay, J. Rajala, G. Deschênes, A. Romanov

ABSTRACT: The Kupol project, located in Far East Russia, treats a high-grade, free-milling ore containing 25.5 g/t Au, 298.3 g/t Ag, and 0.5% pyrite,with a P70of 53 microns. Most of the gold occurs as elec-trum and the silver is predominantly present in the forms of acanthite, stephanite, pyrargyrite, andproustite. The mill reached the design throughput of 3,000 tpd six months after start-up. AKnelson con-centratorrecovers10.4% gold and 0.5% silver. Leaching (14.5 hours pre-treatment and 116 hours cyanidation)of gravity tailings is performed with the CANMET Enhanced Leach Process (CELP),using only 490 ppm NaCN (cyanide consumption of 1.1 kg/t). The precious metals are recovered by counter-current decantation and the Merrill-Crowe process. Calcium hypochlorite destroyscyanide and thiocyanate. Overall, gold and silver recoveries for 2008 were 95.4% and 85.6%,respectively (2.8% and7.5% higher than targets). In the first eight months of 2009, gold and silver recoveries were 95.0% and82.6%, respectively. By August 2009, the mill processed 1.42 million tons of ore with production of 1.1 million ounces of gold and 11.3 million ounces of silver. CELP performance was not affected by changes in feed grade and ore mineralogy. Additional modifications to the leaching strategy allowed further reduction in cyanide consumption and effluent treatment costs.

Jan 1, 2011

By J G. Brady

This paper discusses the ceramic products used in the construction industry in Canada, as well as the main raw materials used in their manufacture. The products include the! following: (1) clay prorlucts -such as facing brick (glazed and unglazed), common brick, facing tile (glazed and un-glazed), terra cotta, load-bearing tile, non-load-bearing tile, structural clay floor tile, quarry tile, drain tile, sew-er pipe, conduits .and flue liners -which are made mainly from domes-tic common clays and shales and from domestic or imported stoneware clays and low-grade fire clays; (2) floor and wall tiles of the whiteware type, which are produced from ingredients such as kaolin, ball clay, feldspar, nepheline syenite, talc, pvro-phyllite and wollastonite; (3) glass products -the major ones being sheet glass, plate glass and mineral wool (glass wool, and rock or slag wool) -which are made from such materials as silica sand, soda ash, salt cake, feldsspar, nepheline syenite, dolomitic limestone, high-calcium limestone. borax and (for rock and slag wool) various rocks or slags;

Jan 1, 1963

By D. Q. Li

"This paper briefly introduces problems that can occur in the design of rare earth separation processes and that require close attention during engineering design. Important factors must be considered include the following. 1) The separation process is primarily based on two points. One is the raw material composition and the other is the product purity requirements. 2) Optimization of the rare earth separation process requires optimization of the flowsheet configuration and each process parameter. 3) The separation of heavy rare earths is performed under non-equilibrium conditions. 4) The radioactive elements uranium and thorium must be removed from the feed to separation. 5) Process economy and environmental protection must be considered together in the evaluation of any separation technology options. INTRODUCTIONThe importance of rare earth (RE) is well recognized in high-tech applications and sophisticated national defense technologies. RE is the treasure house of the 21st Century new materials. The RE separation processes developed using HEHEHP (P507), P507-alcohol (ROH) and naphthenic acid (NA) have been widely applied in China. These processes have led to industrial production of all of the individual RE with up to 4N (99.99%) or higher purity (Li, Wan, Lin, Xie, Lin, & Wang, 1980; Li, Wang, & Xie, 1985; Li, 1995; Li, Wang, Meng, & Li, 2005). In order to achieve the best economic and environmental benefits, this paper discusses several problems to which attention must be paid in the design of rare earth separation process."

Jan 1, 2016

By S. Utili

"The optimal profile of a rock slope under given geometry constraint is investigated by means of the upper bound method of limit analysis. The optimal condition corresponds to maximizing stability factor. It is assumed that rock failure condition is suitably described by the Hoek-Brown criterion. Genetic algorithm is applied for locating the optimal profile. The optimal profiles turn out to be concave profiles but there are heaps around the toes of the slopes. Compared with plane profiles, the percentage of increase in stability factor can reach up to nearly 50%. The key geometry parameters of the optimal profiles are provided for practical use. The new upper bound formulation is capable of computing the stability factors of slopes of any shape, thus the stability status of a slope under man-made excavation can be monitored during the whole construction period.INTRODUCTIONIn mining industry, man-made slopes are excavated to create working surfaces. It is important to optimize the slope profile in order to maximize slope stability under certain geometry constraint. For instance, when the height and width of an excavation are assigned, a plane profile AC (see in Fig. 1) is widely applied in engineering practice, but it has been proved not the best one in terms of safety (Utili & Nova, 2007; Cala, 2007). A vertical profile ABC is the one with least stability. Thus, it can be deduced that there is a profile within the domain of the rectangle ABCD providing the highest stability. Cala (2007) compared the difference of convex and concave profiles in stability using strength reduction technique. According to Cala (2007), circular concave slopes can increase the maximum slope inclination under given factor of safety. Besides, based on upper bound theory of limit analysis, Utili & Nova (2007) assumed a logarithmic spiral profile to prove it is more stable than a plane profile in terms of the stability factor. Although the above studies attempted to seek the best circular or logarithmic spiral profiles, none of them considered the arbitrary shape of the optimal profile and its contribution to enhance slope stability."

Jan 1, 2015

By Marcin Ziemski

This paper reports on an energy efficiency analysis completed as part of a research project looking at energy reduction opportunities in minerals processing operations. The plant discussed is a gold production facility owned by Newmont Gold in the Tanami region of central Australia. Due to its remote location, lack of nearby gas pipeline or power grid, the operation has been completely dependent on diesel fuel for its electricity generation and transport needs. The mine and processing plant use electrical power at a rate of 12MW to 18MW, resulting in a monthly electricity cost of over US$1.5M. The high cost of diesel combined with an impending power generation capacity shortage drove Newmont to undertake the energy efficiency study. An energy audit of the plant showed opportunities for significant energy savings through the strategic use of waste heat, fuel replacement alternatives and renewable energy sources.

May 1, 2007

Strengthening a mine with the Power of their Employees: ?Imagine if the global economy collapses, your head office calls, and tells you to shut down for 3 months... now what do you do? ? HVC Business Improvement Initiative Why did we need help ? External Events ? How we responded ? How we worked with Westwind ? Alignment ? Priorities ? Coaching ? Focus Groups ? Innovation ? What worked / Opportunities ? Questions

Nov 1, 2011

By A. F. Brock

Introduction During the past ten years, shaft sinking has been going on continuously at Inco and new shafts and shaft extensions have been sunk under a broad diversity of conditions. The Murray mine and the Stobie section of the Frood-Stobie mine have?been opened and a main hoisting and supply shaft has been sunk at each of these mines; No. 2 shaft at Murray was sunk initially from surface to 1,960 feet and is now being extended; No. 7 shaft at Stobie was sunk from surface to 3,105 feet. No. 2 shaft at Garson has been extended from 2,200 feet to 3,200 feet in depth. At Levack, No. 2 shaft is being extended from 1,860 feet to 2,850 feet for ore hoisting from the 2,650 lev el. At Creighton, No. 6 shaft, collared on 52 level, was sunk 1,740 feet to a total depth of 5,563 feet below surface. It is the deepest Inco working. At Creighton, also, No. 7 shaft is being sunk from surface to the 30 level to handle the ore from caving operations. Ail Inco main hoisting and supply shafts sunk during the past twenty years have been vertical rectangular shafts equipped with two cages and two ore skips. The cages are standard and interchangeable for all shafts except Garson No. 2; they are single-deck, 13 ft. 4 in. by 5 ft. 2 in. inside and are designed to carry a maximum material load of 16,000 lb. The man load is 48 men. Skip capacities at the several shafts vary from 8 to 15 tons. Forty-two hundred feet bas been established as the standard vertical lift, and the permanent hoisting equipment at each shaft is designed for eventual hoisting from that depth.

Jan 1, 1950

By G. E. Murray

Introduction The development of the method for recovering zinc from lead blast-furnace slags at Trail is interesting and important in the history of both lead and zinc metallurgy. Many efforts have been made in the past, particularly in Germany, to make economic recovery of zinc from slag. The Pape process on Oker slags was successful and is being worked at the present time. More recently the Waelz process has come to the fore. One effort at Cockle Creek, Australia is of special interest in view of subsequent developments. This was re-ported in detail by Guy Courtney in 1920(1). It deserves mention as it shows how, as in many other instances in the metallurgy of lead and zinc, important pioneering work has been done in Australia. These experiments, started over 25 years ago, comprised reduction with coke, powdered coal, and eletrothermically in carbon-lined furnaces. The so-called slag eye furnace, which volatilised the metals from a blast furnace running with a hot top, was also investigated.

Jan 1, 1933