Search Documents

By J. H. C. Scrimgeour, T. Toong, R. E. Hamilton

"The principles involved in the use and application of mathematical models as an aid to the development of advanced process control computer systems are described briefly. This is followed by a brief survey of known models of this kind for the simulation of mining industry processes.The main part of the paper describes a dynamic model of the flotation process developed by Canadian General Electric. Using flotation rate constants for each species of mineral and gangue, the model provides a numerical solution of the differential equations describing cell behaviour. The cell mode] is used repeatedly as a subroutine in the •over-all-plant model. The features of the cell and plant models are described.Simulation runs from the plant model show stream .assays and other indications of plant behaviour printed typically in 1-to 10-minute steps for several hours of •Operation following typical disturbances such as changes in feed rate or reagent addition rate. The simulation can :Show expected behaviour for both uncontrolled and computer-controlled plants."

Jan 1, 1970

By N. Schmalbein, L. von Ketelhodt, L. Kotelo

"The mining industry continues to remain challenged. Lower commodity prices, increasing labor costs and more importantly diminishing reserves are amongst some of the primary factors contributing to the difficulties faced. Ore sorting technologies have demonstrated their potential to improve the downstream beneficiation performance. The general processing route sees all primary crushed material milled for liberation and then processed in accordance with characteristics of the gold therein, i.e.: refractory golds would require direct leaching or oxidation whilst free gold would follow the conventional cyanidation process, after gravity concentration. Ore dilution increases the associated operating costs within each stage of this process. The opportunity to process the same throughput at a higher grade can only be achieved through pre-concentration. Sensor based sorting has been examined on numerous occasions by various gold producers. Test work carried out on different bulk low grade gold ores has shown the successful applicability of ore sorting to remove waste, whilst maintaining high recovery rates of gold. The results of a combined XRT/Laser sensor sorter have shown grade improvements of over 300% from feed grades of 0,25g/t to 1,15g/t at gold recoveries of 66% and waste ejection rates of 85%. This paper presents some of the results from the work undertaken by STEINERT with respect to gold sulphide ore sorting and presents a modelled financial scenario, which can enable a company to target and reclaim low grade ores.INTRODUCTION The mining and minerals processing industry presents with many different challenges including, volatile commodity prices, increasing labor costs and more importantly diminishing reserves. Conventional processing routes will continue to play a crucial role in the beneficiation process, however innovative methods of reducing operating costs and optimizing on the overall circuit performance is where technologies such as sensor based sorting come into the fore. Sensor based sorting as a dry mechanical process not only reduces water consumption by eliminating unnecessary waste but also reduces the requirements for reagents in the downstream processes. Sensor based sorting under dry conditions presents a highly efficient alternative to wet pre-concentration methods such as dense medium separation (DMS)."

Jan 1, 2017

By Jason Mewis

Jason Mewis is the founder and president of ENGCOMP, a consulting engineering firm in Saskatoon Saskatchewan focusing on the mining sector. He has over 17 years of experience working on projects for the heavy industrial market in Saskatchewan, as both a Senior Structural Engineer and Project Manager. Jason is an entrepreneur with experience in many areas including estimating, planning, facilitation, and Risk Analysis. He has presented at many seminars and conferences across North America on the subject of Project Risk and and has become recognized for his expertise in this area of project management.

May 1, 2013

By David Sanscartier, Elizaveta Petelina, Alexey Klyashtorin

This paper provides an overview of the radiological risk mitigation approach applied by the Saskatchewan Research Council (SRC) for the remediation of 35 legacy uranium mine sites in northern Saskatchewan where uranium exploration and extraction took place in the 1950–60s. Mining activities resulted in an irregular increase of the gamma radiation dose rate (up to 18 μSv/h). The radiological objectives for the sites include a gamma dose rate at a spot (<2.5 μSv/h above local background), and the dose rate averaged over a hectare (<1 μSv/h above local background). These objectives are generally achievable at the impacted sites through the installation of shielding soil cover. This method may be impractical for site areas with rough terrain (e.g., steep slopes) and/or difficult access. A risk assessment approach is applied to determine if these areas can be safely left uncovered or if additional mitigation measures should be implemented. The risk assessment approach is based on two factors: (i) the ambient radiation dose rates collected through gamma surveys, and (ii) actual land use data collected through various surveys of activities of local community members at the sites. Exposure scenarios based on four land uses are applied to estimate a potential annual dose load for members of the public. The estimated doses are compared with the criterion of 0.3 mSv/a recommended by the Canadian Guidelines for the Management of Naturally Occurring Radioactive Materials (NORM). If the criteria are not satisfied, a mitigation plan is developed, and post-remediation gamma levels are modelled using GIS tools to evaluate the performance of the proposed mitigations. The proposed approach allows the team to optimize resources for the site remediation so that public exposure to NORM are as low as reasonably achievable after remediation.

Jan 1, 2020

By Paul W. Billwiller

Introduction In 1937, the Britannia Mining and Smelting Company, Limited, was carrying on an extensive exploratory diamond-drilling programme. Most of this drilling was done on the 4100 level, the lowest working level in the mine. One of the exploratory diamond-drill holes, at approximately 12,500 feet from the portal of the tunnel, encountered heavily mineralized stringers of chalcopyrite and sphalerite in silicified grey schist. The mineralization was encountered just to the hanging-wall of the green mottled schist at a point 350 feet south of the 4100 tunnel. To delimit this new orebody, drifts and cross-cuts were driven on 3500, 3800, and 4100 levels to the hanging-wall in the area of the projected mineralization. On the 3500 level, the top of the mineralized zone was encountered. The zone was thoroughly explored by drifting and diamond drilling. The mineralization, however, was not sufficiently concentrated to be of commercial grade. On the 3800 level, the zone was found to consist of disconnected stringers of chalcopyrite and pyrite. Drifting was continued to the west and a long lens-shaped area of grey schist containing fairly heavy stringers of chalcopyrite was delimited. This lens later proved to be very close to the top of the commercial mineralization of the No. 8 orebody. On the 4100 level, a diagonal cross-cut was driven to the footwall of the downward projection of the mineralized zone. Diamond-drill holes from this cross-cut indicated a zone of heavy mineralization. A drift was driven off the cross-cut parallel to the zone and some distance to the footwall of it. Further diamond drilling disclosed a mineralized zone approximately 300 feet long and 35 feet wide containing sphalerite, chalcopyrite, and pyrite. The foregoing development work indicated a fairly large lens of mineralization of sufficient concentration to be classed as ore between the 4100 and 3800 levels. To explore this mineralization at depth, long diamond drill holes, dipping at minus 57° and minus 80°, were planned from some point to the hanging-wall of the orebody. The 4100 level was not suitable for small development headings, due to wider gauge track and larger cars than on the levels above. Therefore, a raise was driven from the diagonal cross-cut on the 4100 level to a point some 70 feet above and just inside the footwall of the orebody. From the top of the raise, drifts were expanded east and west to delimit the ore zone. In addition, a long cross-cut was driven 350 feet to the hanging-wall, and drifts were opened east and west from the end of the cross-cut to provide diamond-drill stations for the exploration of the orebody at depth.

Jan 1, 1946

By L. Garrigues, M. Jarvis, M. Halhead, O. A. Bascur

"Large variability of ore types, escalating variables operating costs and increased throughput require large investment in sensors and systems in mineral processing operations. Mining and mineral processing plants collect and manage more data than a small city with much in real-time. The data is changing rapidly as internal and external conditions evolve. As corporations buy and sell assets, and reengineer their staff, the structure and tools that were used to understand this data is lost. This results in significant deterioration in the ability to maintain a smart operation. When data is recognized as a critical asset and managed as part of an infrastructure, it become a key enabler to help transform the entire operations. In many situations, all partners in business collaboration—such as join ventures, contract manufacturer, expert service providers, and operations and maintenance companies—need access to production and asset data. The emergence and maturation of Cloud technologies make it possible to easily connect the plants to external equipment suppliers and operational support service.This paper will share examples of how mineral processors have adopted new data strategies such as self-service business intelligence, cloud computing and internal/external collaboration.INTRODUCTIONOne of the main challenges in mineral and metallurgical processing plants is effective energy and water management. The lowering of ore grades requires higher throughputs while the ores are getting more complex with variable mineralogical compositions. Electrical energy supply is becoming a restriction in many countries. Rising water management costs has a direct impact on the profitability of the operations. Grade recovery versus energy consumption in copper production for both open pit and underground mines has been described by Fuerstenau (2001). Comminution uses over 55% of the energy to produce nonferrous metals while other operations require much less energy (Nelson, Richins, & Lelinski, 2013)."

Jan 1, 2016

By I. Tinto

"IntroductionEnvironmental pollution problems, caused by gases or effluents, by high noise levels or from air borne dust, are placing increasing demands of the operators, from statutory authorities, and from the general public, to adopt more stringent dust control measures. This requires that a successful plant dust control program be an integral part of any plant operation. While a successful environmental program is a key factor in maintaining productivity and good labour relations, anticipation of future environmental regulations during the plant design phase can avoid the high cost of plant upgrading, or dealing with pulmonary conditions in the work force in subsequent years.Particulate removal, conventionally called dust collection, involves the removal of coarse- and fine-particulates from the airstream. Although generally limited to that required for contro!Hng plant generated air emissions, particulate control equipment also has a wide application for air cleaning and filtration inside the plant, as well as for recovery of usable products.In the late 1950s and early 1960s the public became more concerned with the problems of air pollution. This increasing concern was stirred by an awareness of the extremes to which water pollution had progressed in many of the rivers and lakes, by increasing perception of air pollution as detected by visible smog and harsh chemical odors, by the alarming rate of increase of smog plagued cities and communities, and by specific incidents where ill health could be traced to specific episodes of air pollution. Particle size is perhaps the most important single factor affecting particulate control. Large particles (over 5 microns) constitute the major mass fraction of most sources of emission and economical control equipment dqes exist for their efficient control. However, while these larger particles frequently represent the source of soiling and unsightly smoke plumes, they are not a major health problem as they tend to settle relatively quickly, are more easily scrubbed from the atmosphere by rain, and are not able to penetrate the respiratory system. By far the most important form of particulate air pollution is the fine particulate, (below 3 microns) which is harmful to the pulmonary system. The adverse effects caused by this particulate matter on human health are for the most part related to injury to the surfaces of the respiratory system. Particulate material in the respiratory tract may produce injury itself, or it may act in conjunction with gases, altering their sites or their modes of action. A combination of particulates and gases may produce an effect that is greater than the sum of the effects caused by either individually (i.e. synergistic effect)."

Jan 1, 1989

By A. Kapoor, L. Morin, S. Mortazavi, P. Béedard, Gould. W. D., A. Kuiper

The degradation of thiocyanate in a simulated gold mill effluent was studied using a laboratory scale rotating biological contactor (RBC). Complete SCN- removal was obtained at temperatures of 8 and 12°C, and a hydraulic retention time of approximately 3.3 h. The NH4+ produced by thiocyanate hydrolysis was oxidized by nitrifying bacteria to NO2 and NO3-. The HS- produced by thiocyanate hydrolysis was chemically and biologically oxidized to elemental S, which was subsequently biologically oxidized to sulfate. Incomplete sulfur oxidation occurred in the RBC, particularly at 8°C and elemental sulfur deposition was observed on the RBC disks. The RBC feed exhibited toxicity to rainbow trout but the RBC was effective in removing the acute toxicity of thiocyanate.

Jan 1, 2005

By F. Parada Luna, F. Parada Torres, J. Salvo, A. Reghezza

In the pyrometallurgical processes of copper concentrates, arsenic is preferentially concentrated in the dusts carried by the gases as a result of their volatility and subsequent condensation in the gas cleaning train. In this work results obtained by alkaline leaching of the dusts from Ministro Hales roasting plant, belonging to Codelco, are presented. For the Ministro Hales plant the alkaline leaching would be an alternative to the recirculation of dusts to the roasting furnace. The experimental study considered NaOH and NaOH plus NaHS leaching of two samples of dusts, with 4.24 and 2.55% arsenic respectively. The results show that it is feasible to extract 90% of the arsenic and 50% of the antimony at room temperature using only NaOH, and when the temperature increases to 95ºC, the extractions of As and Sb increase. Copper remains in the solid residue with less than 1% dissolution, and the NaOH net consumption was approximately 140 kg/t of dust. In leaching tests with NaOH + NaHS, two types of methods were tested, baking plus leaching with water and direct leaching with a NaOH+NaHS solution. With the second method arsenic extraction increased to 95% and copper dissolution was less than 0.01% at 85ºC, NaOH 100 g/L, NaHS 90 g/L, 1.5 h and L/S ratio of 5/1 (L/kg). The bismuth remains stable in the solid in all cases. INTRODUCTION The presence of arsenic in copper concentrates has increased with time and the environmental regulations are becoming increasingly more stringent. In concentrate treatment pyrometallurgical plants, most of the arsenic is volatilized condensing in the gas train and is collected along with the entrained solids to form the flue dusts. Under these conditions, in smelters of copper concentrates with high arsenic content, the dusts are being treated in hydrometallurgical plants to extract and stabilize the arsenic, which also means that most of the copper contained in the dust is co-extracted with the arsenic. This affects the recovery of copper in the smelter and an alternative such as the selective alkaline leaching of arsenic, would allow the copper from flue dust to be recovered.

Jan 1, 2019

By Guangyuan Li

A 3-D block-spring model (BSM) has been developed for simulating the behaviour of jointed rocks. The model uses a discontinuous formulation and an iterative procedure to solve the large displacements in jointed and faulted rock masses. The 3-D BSM has been used to simulate mining excavations in jointed rocks around an open pit and underground settings. The applications have demonstrated that it is a practical tool to solve complicated problems of rock mechanics in civil and mining engineering. This model has recently been modified to incorporate complex geological conditions, such as underground water flow (seepage), unstable blocks and the time-dependent behavior of backfill materials. To demonstrate the capability of the 3-D model this paper presents the fundamentals of the 3- D BSM and its application for open-pit mining. A complete computer package BSM3D has been developed based on the 3-D block-spring model. The package consists of a solving engine for numerical analysis and a Windows based processor for mesh generation and results display. The multi-functioned pre-processor provides tools and menus to help users setting up models easily and conveniently. The fully featured post-processor allows users to view the results in different windows and orientations. The graphical results include contours, vectors, animation of rock movement, and the failure state of the rock structures.

May 1, 2001

By A. P. Paiva

The solvent extraction properties exhibited by some /V,N&apos;-tetrasubstituted malonamides to efficiently and selectively recover iron(III) from concentrated chloride leaching solutions can be found in the recent literature. The iron(III) extractive chemistry exhibited by some of these derivatives is revisited, in order to compare their chemistry with that shown by a few of the new malonamide compounds. The generally good extraction efficiency towards Fe(III), from >4 M hydrochloric acid solutions, and the relative ease of Fe(III) stripping by distilled water are remarkable findings that are confirmed for the malonamide derivatives described in this work. Furthermore, additional data regarding their selectivity towards Fe(III) extraction over several base metal ions and their behavior when subjected to successive Fe(III) extraction-stripping tests are also presented and discussed.

Jan 1, 2006

By J. Peterson

A review of blast designs and improved blasting practices at the Ekati??Diamond Mine is presented along with the results of three blast-monitoring experiments. Blast monitoring was undertaken to investigate blast damage mechanisms in the mine&apos;s well jointed rock mass. Rock mass damage caused by production, pre-shear and wall control blasts was measured. Ekati??uses 270mm holes for production blasting, and 165mm holes loaded with a decoupled charge for pre-shearing. The production blasts are loaded with bulk emulsion / ANFO blends. The mine plan involves using 30m double benches. A 30m high pre-shear is drilled and blasted prior to the production blasting that is done with sequential 15m benches. This paper summarizes the monitoring equipment and data gathered to date.

May 1, 2001

By J. T. Chen, S. Winkler, M. J. Worswick, O. Orlov

This paper presents a review of research conducted at the University of Waterloo concerned with the application of aluminum alloy sheet and tube in automotive structures and body panels. The research has focussed on formability prediction and results using a range of damage-based formulations. These models include continuum-level damage approaches and, more recently, a so-called percolation damage approach intended to capture microstructural heterogeneity effects on damage development. This paper presents applications of these damage approaches to simulate formability of experiments considering stretch flange panels. The experiments consider drawbead effects associated with the bend/unbend deformation as the material flows through the drawbead. Recent work on simulating in situ X-ray tomography experiments that capture damage evolution during tensile deformation will also be reviewed.

Jan 1, 2006

By F. Channier

The paper provides the most recent information on the construction of the AP60 phase 1 plant of Jonquiere which is due to be commissioned and started up in the first quarter of 2013. HSE management on site by RTA, and cooperation with local equipment manufacturers and contractors of the Saguenay-Lac Saint Jean region are highlighted in this section. The AP60 phase 1 Jonquiere plant aims to demonstrate of the AP60 technology at an industrial scale and allows the further developments of the AP60 cell. The advantages of the AP60 cell technology in terms of productivity, power consumption and environmental footprint are also briefly presented in the paper.

Jan 1, 2011

By K. C. Corin, Z. G. Song, J. G. Wiese

In the present investigation flotation was used as a diagnostic to understand the effects of changes to the media during the grinding stage. The observations from flotation for different media are discussed in terms of particle size distribution, water recovery, solid recovery and valuable mineral recovery. The chemical parameters; pH, redox potential (Eh) and dissolved oxygen (DO) levels were measured. A Base Metal Sulphide (BMS) ore was ground under media of different shapes and compositions to determine the effect of different rod/ball material on the flotation performance of the ore. For a given grind (D80 = 75 µm), media shape had no effect on flotation performance of a BMS ore. Different grinding media had significant effect on slurry chemical properties and flotation performance. Mild steel rods (RMMS) produced the highest solids recovery, nickel and pyrrhotite (Po) recovery, with the highest ethylenediaminetetraacetic acid (EDTA) extractable iron and the lowest DO level. Chrome steel balls and stainless steel rods produced the lowest metal recovery, EDTA extractable iron and the highest DO level. A complementary study was conducted to investigate the effect of using different grinding media compositions, viz, ceramic, forged steel, 15% chrome steel, stainless steel and a mixture of stainless steel and 15% chrome steel (50:50) balls were investigated using a Platinum Group Mineral (PGM), UG2 ore. Grinding products of five different media produced the same solids and water recovery, but the grades and recoveries of Platinum Group Elements (PGE) and chromite were different. Grinding products of ceramic media showed the best flotation performance, with the highest PGE recovery and the lowest Cr2O3 recovery. While grinding products of stainless steel balls (SS) produced the lowest PGE recovery and highest Cr2O3 grade and recovery in the concentrates.

Jan 1, 2016

By Ralph H. Cleland

GENERALLY speaking, the Industry lost ground in 1941 in its accident experience. Though the frequency of compensation accidents was but slightly higher than in the previous year and well below past experience, our fatality rate shot up to that obtaining in 1938, and the average cost per man employed was the highest for some time. The number of fatalities was 56 in 1941 as against 33 in 1940. The average cost of compensation per man employed was $34.25 in 1941 as against $28.43. There was but a slight increase in the number of men employed. Accident prevention efforts were maintained, as shown by our frequency, but our accidents were of a more serious nature. In a period of considerable labour turnover, with many new men entering the Industry, especially the base-metal division, and much mental distraction, we might well have expected a high rate of accidents. That this did not occur is a tribute to managers, supervisors, and workmen alike. We all regret the high fatality rate and one must consider why this occurred. So far as it is possible to determine, there is no apparent explanation. There were no disasters. The accidents occurred to the same class of work-men, both in respect to jobs and age groups, and from the same age-old causes that we all know so well. Luck is a big factor in the seriousness of an accident; the solution lies in preventing accidents, even first-aid cases. Generally speaking, if minor accidents do not occur, major accidents do not occur.

Jan 1, 1942

By B. N. Church, J. J. Barakso, A. F. Bowman

"An evaluation of mineralization in the Goosly- Owen Lake area of central British Columbia is the result of a comprehensive geochemical study of rock samples obtained from a regional geological survey. The dispersion of metals in country rocks about a line of Tertiary intrusions suggests that these igneous bodies may be genetically related to known sulphide replacements, disseminations and vein deposits. The geochemical investigation is based on the determination of 12 elements from samples gathered from more than 800 scattered field stations. To assist processing and interpretation, the data are subjected to a variety of statistical procedures, including correlation of the elements, factor analysis, clustm• analysis and computer contouring of the elements. Some practical applications of rock geochemistry in regional exploration are indicated."

Jan 1, 1976

By J. Kolacz

"A new sensor based sorting system has been developed, providing a possibility for laboratory scale testing and further scale-up of the separation results to the industrial operation. The new system contains different sensors as: X-ray detectors, visible light cameras, NIR cameras, ultraviolet cameras and magnetic sensors, in the same sorting unit. The sorting unit allows advanced calibration options and fine-tuning of the installed sensors to achieve the best separation effect under controlled conditions. Finally, the processed material can be analysed and separated by the rejection mechanism, similarly to the industrial scale operation. At the same time, the process is carried out with limited amount of material allowing detailed statistical calculations for processed particles and all sensor types. The optimal settings and sensor types are specified for the industrial application.The paper describes the scale up of the results achieved for iron ore and coal, where the test work was first carried out using the new laboratory sorting system and where the industrial scale sorting system has been built, in the final stage. The industrial scale sorting results showed a very good correlation between the laboratory and full scale operation. Thanks to the detailed study carried out in the laboratory equipment, the settings of the sensors in the full scale operation provided much better separation efficiency. It was especially important to provide proper setting for the X-ray sensor data calculations, which can be very critical for achieving the best results. During the industrial scale sorting of coal, the input material had 40-55% rock particles as the direct source of ash in the coal stream. The optimal laboratory unit settings and transferring these settings to the industrial sorter, provided 98.8% efficiency for removing rock particles with only few % losses of coal."

Jan 1, 2016

By T. L. McCall

A short description of mining practice in the Sydney coal field in general is followed by a discussion of the operations in the No. 12 colliery of the Dominion Coal Company, Limited, as being typical of the trend in operating methods obtaining throughout the field. Development of longwall mining to the present system of three walls in line is outlined, together with a summary of the cycle of operations involved in systematic operation.

Jan 1, 1944

By Henrik Saxén, Mikko Helle, Hamid Ghanbari

In this study, a process integration approach in a primary steelmaking is investigated to evaluate future operation concepts of a steelmaking site considering sustainability issues. Mathematical programming is used to study the integration of the steel plant with chemical units for utilization of available off-gases in the system, and carbon capturing and sequestration unit. Different industrial carbon utilization options are considered to find the best route of development. A multi-period optimization model is developed based on site-wide mass and energy balances by considering the availability of the fuels and by-product gases and their consumption in the production system and a conceptual polygeneration system. The objective is to reach maximum economic profit while environmental aspects of integrated system are considered for different fuel systems, alternative blast furnace reductants and implementation of new process technologies. The model can provide useful information concerning techno-environmental and economic aspects for decision-making and can estimate optimal operational condition of current and future primary steelmaking under alternative scenarios. The results of the work illustrate the potential to develop steelmaking towards more sustainable operation in the future.

Jan 1, 2015