Search Documents

Activated carbon is ideally suited to treating low grade ores and tailings by the carbon-in-pulp process and is rapidly replacing the use of zinc for recovering gold from cyanide leach solutions. Coarse carbon particles derived from coconut shell adsorb up to 30,000 ppm Au as a gold cyanide complex and can leave barren solutions containing

Jan 1, 1982

In conjunction with a study on wear of drag bits the effect of clearance angle on penetration rate was studied.Increases in clearance angle from 24 1/2 up to 30° gave an increase in penetration rate. Thereafter the rate was apparently affected by partial clogging with cuttings.Analysis of results was by a linear regression model and the t-test was applied to assess the significance of parameters in the penetration equation.

Jan 1, 1969

By Mitchell D. S

BackgroundIn March 1990 Pasminco resolved to replace and increase the capacity of the underground pumping system at the Southern Operations, Broken Hill. The existing pump station was built 23 years ago while the rising main had been in service for 38 years and was subject to frequent failure.The old system was a conventional slurry/clear water separation and multi-stage pumping system. It was inadequate in the following areas:ò insufficient capacity to handle current and expected future flows;ò unable to consistently dewater lower production areas; ò pumping capacity restricted sandfilling rates;ò dirty water dams had insufficient settling capacity and were difficult to de-sludge;ò the operating costs of dewatering were high; ò it was labour intensive; andò it did not offer enough protection to the 25 level loading station.

Jan 1, 1993

By W Mez

The German mining industry uses different residues for backfilling and stowing. A hydraulic pipe conveying technology for these materials has shown advantages for the transportation into the mine. Pipeline conveying systems are able to bridge long distances, they save room within the underground workings and they save staff and costs. Absolutely necessary for successful use of the hydraulic conveying technology is the knowledge about the unusual non-Newtonian flow properties of solid/liquid mixtures like pastes and slurries. The flow resistance of these materials cannot be described easily by one viscosity. Owing to a yield point and a pseudo-plastic behaviour the viscosity changes with the shear rate and with the streaming velocity inside the pipe. Also these flow behaviours depend very sensitively on the liquid/solid-ratio, often so dramatically that gravimetric or volumetric dosing equipment is not in a position to control the production of backfill pastes. Quality changes of the solid raw materials (particle size distribution, density, mineralogical composition) lead to additional difficulties. The first experiences with hydraulic backfilling plants were troubled by plugged pipes, a bad backfill quality caused by unnecessarily high water content and high costs for chemical binders to solidify the backfill. The installation of viscosity controlled paste production leads to success with the hydraulic backfill technology. A development of the DMT, a bypass pipe-viscometer, has been the key technology. The system is able to analyse on-line, difficult, sticky and abrasive substances and determine their non-Newtonian flow properties. Because the system measures real physical values it is in a position to pre-calculate process relevant parameters like the pressure drop of the backfilling paste in the conveying pipeline. Newer types of the viscometer system also measure the slurry density and calculate its composition. These systems have proven a success controlling backfill paste production plants. They offer a secure prevention of pipeline plugging and a production of high quality backfill pastes with a water content as low as possible.

Jan 1, 1998

During the past three years there have been several parties prospecting for oil in the Stat6 of Queensland, and It was: gratifying to read the newspaper headlines last Christmasabout the discovery of oil in the Moohie Nol Well. This discovery was not only a welcome Christmas present for Australia but marked up another success for the seismicmethod in exploration for oil.The purpose of this paper is to discuss the operationaI aspects of seismic work in Queensland with-emphasis on shot-haledrilling. The paper is based upon the experience of one particular seismic survey which began in December of - 1959 and is still inoperation. This survey is being conducted by the Petty Geophysical Engineering - Company of San Antonios, Texas, and the Queensland area involved is in the general vicinity of Quilpie, Dlackall and Charleville.

Jan 1, 1962

By E House, V Lisitsin

Recent whole-rock geochemical data from nearly 900 fresh drill core and underground samples taken from seven central Victorian gold deposits confirm the presence of distinct and identifiable primary alteration haloes surrounding the deposits. Ferroan carbonate alteration extends for up to several hundred metres away from turbidite-hosted gold mineralisation outside of contact metamorphic aureoles. A less distinct phyllic alteration zone can be identified using geochemical molar ratios or short wave infrared analysis. It generally overlaps a sulfidic halo characterised by disseminated pyrite and in close proximity to mineralised structures, arsenopyrite. The extent of the sulfidic halo can be traced using low-level analysis of pathfinder elements such as S, Au, As and Sb. Recognition of these alteration features enlarges the target for exploration and provides a tool by which drilling can be directed towards mineralised structures. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

The Cleveland Mine has an annual ore production of 400,000 tonnes at a grade of 0.79 per cent tin and 0.30 per cent copper. It is achieved by an open stoping method, mechanised overhead sub-level benching. The operation is trackless with a ramp access from all working places to the surf- ace. Broken material is loaded from the stope and development headings into diesel trucks and hauled to the surface crushing plant.

Jan 1, 1977

As Coal Mining Areas develop, problems relating to strata control increase. The "easy" coal has been extracted and the future development lies in the direction of greater depths of cover and more difficult strata conditions. To provide solutions to the problems encountered the techniques of constructing and testing physical models have been developed and refined. With a sound knowledge of model theory allied to practical experience, mining research engineers use physical cemented material models to examine, assess and solve mining problems relateu to strata behaviour and environment. For a model to provide the answer to a particular mining problem it is essential that as much information as possible be obtained from the mine or area of a mine which the model is to represent. Details relating to the strata, geological malformations, and the stress environment must be collected and collated to ensure reliable results.

Jan 1, 1976

By J L. Merritt

Effective minesite water management requires that this issue be treated as a risk management exercise. The management process is generally far from simple and by necessity must involve a range of personnel covering a siteÆs commercial, operational and environmental interests and responsibilities. The challenge to be collectively faced by these stakeholders is to strike the correct balance between risk and cost. On the other hand, the challenge to be faced by technical services support personnel is to provide stakeholders with information in a format that they can use with confidence. This paper presents the application of continuous operational simulation (OPSIM) modelling techniques to establish appropriate risk profiles for minesite operations. It is necessary that the format of these risk profiles be generic and equally applicable for defining the risk of occurrence for a relatively comprehensive range of activities û eg from of a non-compliant discharge, to the risk of failure to meet production targets. What is more, the profiles need to be quantitatively based and capable of reflecting change in system response to varied operational or management strategies. The techniques presented in this paper are based around a key assumption that long-term records of the climate contain within them sets of sequences that are representative of what can be expected in the future û that is, the droughts, floods, cyclones, good years and bad, long or short, and everything in between. Therefore, if these historical records are run through an OPSIM model for a particular site, then the simulated operational characteristics can be taken as being representative of what can be expected in the future, in the long-term. This lends itself to statistical analysis and translation into the required risk based format. Water Solutions Pty Ltd have been working with Capricorn Coal Management to develop a relatively comprehensive OPSIM model of their operations at German Creek Mine, Central Queensland. Outcomes from the modelling have been used in recent times to provide mine management with risk-based guidelines for both securing and containing mine water inventories. One of the more interesting tasks has been to establish risk based inventory levels that, if reached, would trigger the immediate implementation of a contract for the desalination and re-use of mine water, at predefined rates. Also, lead-time warning of the occurrence of a possible trigger is of importance to operational and commercial planning. To service this requirement the OPSIM model is regularly used to produce lead-time estimates to defined levels of confidence. Case studies of these, and other, applications of the OPSIM model at German Creek Mine are presented in this paper and serve to demonstrate an effective methodology for practical risked based water management.

Jan 1, 2003

The firing of mass blasts at Isa Mine is a normal operating practice. Both electric and non-electric initiating systems are being used for this purpose. The advantages gained by large firings relate to the Planning, Scheduling, Services and Production functions of Isa Mine. More efficient us"e is made of manpower due to the concentrated charging effort and con- tinuity of the charging operation. In addition, the requirement for ring firing personnel to work at the edge of large stope voids is reduced. Better fragmentation results from the interaction of adjacent detonating rings of blastholes and in flight collisions. With mass blasts there is also less chance of large blocks of ore, created by faults or joints, falling into the stope and creating problems at the drawpoints. The formation of a large tonnage of broken ore facilitates production at scheduled rates from that stope source. The weight of explosive detonating during a mass blast can be considerable. Isa Mine has achieved satisfactory blasting results without excessive ground vibration levels and present knowledge indicates that pillar ground stab- ility has been maintained.

Jan 1, 1978

By Toomey P. T

In many open cut coal mines, rivers and large creeks can cause planning and operating difficulties, both in the terms of the more obvious location of the current watercourse, but, and sometimes more importantly, past meandering of the watercourse. Prevent and past flow regimes may have deposited large alluvial sequences within the current mining areas. The presence of groundwater within the alluvium further complicates the planning and operating practices.A situation exists at Saraji Mine in which alluvial sediments overlie a massive sandstone sequence which in turn lies at about one metre above the coal seam. The problems encountered include high levels of groundwater ingress to the pit, highwall instability, and an unacceptably high rate of blast hole collapse (prior to charging with explosives). Other aspects of the dragline stripping operation were also affected.

Jan 1, 1992

The Burragorang Valley lies approx. 95 km by road south west of Sydney and some 35 km west of Camden. It is over 80 km in length and varies in width from 3 km to over 16 km. Geologically, the history of the Burragorang Valley is of interest. It was referred to by early geographers and N.R.M.A. booklets as the largest sunken valley in Australia. This description is incorrect as it is a water worn valley formed by the dissection of an uplift in the south western portion of the large Sydney Sedimentary Basin. Ages2 ago there extended right across the Blue Mountains, a continuous tableland into which the Nattai, Wollondilly and Cox's Rivers have carved out the formation of the Burragorang. This dissection together with other valleys such as the Megalong, Jamieson and Grose, formed part of the eastward drainage pattern of the uplifting tableland into the Pacific ocean. The lapse of time since the streams in the Burragorang began their work of erosion can

Jan 1, 1976

By White B

The domestic and commercial use of underground space dates back to Neanderthal man living in caves. There are many examples worldwide of the imaginative use of underground excavations, either left by mining or purpose-built. World living trends indicate that an increasing percentage of the population is living in and around major cities. Environmental, social and economic pressures associated with urban expansion can be partially catered for by a well-planned and integrated underground space regime. This paper addresses the types of underground development that are complementary to the economic and environmental pressures associated with urban expansion and high density cities. The paper explores the implications of mining and exploration technology and civil engineering, as well as the ancillary professional disciplines (legal, architecture and planning, sociology and education).

Jan 1, 1997

Electronic detonators bring a fundamental and radical change to the potential of rockbreaking operations. The immense technical challenge of safely merging electronic systems with explosives has been largely overcome, but a surprisingly difficult obstacle has been to convert users to the much more capable electronic systems, in routine as opposed to exotic applications. Unit cost is probably the main point of resistance. For years papers have confirmed significant improvements in blasting results, feeding through to enhanced bottom line value for the whole operation: much reduced environmental impact, and improved control over fragmentation, muckpile shape and overbreak. In Africa, a number of operations have been employing the technology for sufficient time to see enduring improvements in throughput, control and cost structure, and these improvements have fed through to the planning process: both the cost and the benefits are part of the plan. This has essentially rendered very unattractive the option of reverting to pyrotechnic systems and incurring the penalties previously unseen but now understood to be avoidable. Examples given are of improved throughput at opencast and underground mines, and greatly extended life at an urban quarry. The general experience of management in implementing the technology is that it over-delivers: adopted to solve one particular problem, significant other issues are also addressed. These extra benefits were quite logical, but not at all obvious prior to implementation. Exploring this reality is essential for harvesting the benefits of the technology sooner rather than later.

Jan 1, 2004

By Will D. P

A 328 m, 2.4 m diameter raise-bored shaft has been equipped with a modular ladderway system to provide a second means of egress from Aberfoyle's Hellyer Mine in Tasmania. The modular ladderway consists of platforms, ladders and service pipes assembled at the surface and progressively lowered down the shaft. This system provides a rapid, safe and economical non-entry approach to equipping a shaft. The modular construction and single suspension allows for future extension or for reuse in another shaft.

Jan 1, 1988

The Amacan Copper Project was constructed in the Philippines by a Finnish-Filipino Consortium during the years 1979 - 1982. The project involved a turnkey contract for a mine and a concentrator to process 25 000 tonne per day of porphy- ritic copper ore at a grade of 0.45% Cu. The orebody is located on Mindanao, the southernmost island of the Philippines, in rugged, mountainous terrain approximately 1 000 m above sea level. The adopted design principle was based on an efficient, straightforward installation utilising a minimum number of items of equipment each with high unit capacities. The consortium faced many problems which resulted in lengthy delays in construction and finally led to the client taking over responsibility for the completion of the project. The concentrator was successfully commissioned in July 1982.

Jan 1, 1986

The Carnilya Hill Mine, a joint venture project between Western Mining Corporation Limited (WMC) and The Broken Hill Proprietary Company (BHP), is a nickel sulphide deposit being developed by the Kambalda Nickel Operations (KNO) of Western Mining Corporation. Seven months elapsed from the time a decision to proceed with the project was taken until the first ore production. During the first month of operation a new KNO record for decline development was set. Equipment used includes an electro- hydraulic drill jumbo, 4 cubic metre front end loaders, and 35 tonne haulage trucks.

Jan 1, 1981

By I Brunton

Blast fragmentation can have a significant impact on the profitability of a mine. An optimum run of mine (ROM) size distribution is required to maximise the performance of downstream processes. If this fragmentation size distribution can be modelled and controlled, the operation will have made a significant advancement towards improving its performance. Blast fragmentation modelling is an important step in Mine to MillTM optimisation. It allows the estimation of blast fragmentation distributions for a number of different rock mass, blast geometry, and explosive parameters. These distributions can then be modelled in downstream mining and milling processes to determine the optimum blast design. When a blast hole is detonated rock breakage occurs in two different stress regions û compressive and tensile. In the first region, compressive stress waves form a æcrushed zoneÆ directly adjacent to the blast hole. The second region, termed the æcracked zoneÆ, occurs outside the crush one. The widely used Kuz-Ram model does not recognise these two blast regions. In the Kuz-Ram model the mean fragment size from the blast is approximated and is then used to estimate the remaining size distribution. Experience has shown that this model predicts the coarse end reasonably accurately, but it can significantly underestimate the amount of fines generated. As part of the Australian Mineral Industries Research Association (AMIRA) P483A Mine to MillTM project, the Two-Component Model (TCM) and Crush Zone Model (CZM), developed by the Julius Kruttschnitt Mineral Research Centre (JKMRC), were compared and evaluated to measured ROM fragmentation distributions. An important criteria for this comparison was the variation of model results from measured ROM in the fine to intermediate section (1 mm to 100 mm) of the fragmentation curve. This region of the distribution is important for Mine to MillTM optimisation. The comparison of modelled and Split ROM fragmentation distributions has been conducted in harder ores (UCS greater than 80 MPa). Further work involves modelling softer ores. The comparisons will be continued with future site surveys to increase confidence in the comparison of the CZM and TCM to Split results. Stochastic fragmentation modelling will then be conducted to take into account variation of input parameters. A window of possible fragmentation distributions can be compared to those obtained by Split. Following this work, an improved fragmentation model will be developed in response to these findings.

Jan 1, 2001

By Nemcik JA, Gale W. J

The magnitude and orientation of the in situ stressfield has been determined as a key factor in controlling the stability of openings for both coal mine development and extraction. Monitoring of roadway and pillar behaviour in conjunction with numerical analysis has identified specific stress control measures that have been successfully applied to improve productivity in underground coal mining operations. The influence of the major horizontal stressfield on the stability of openings has been identified at a wide range of sites including mines in Australia, Britain, the USA, New Zealand and Japan. Stress mapping, stress measurement and stress monitoring techniques have been applied to define the in situ stress regime and, together with the correlation of measurements of rock deformation and rock reinforcement behaviour, has enabled appropriate stress control measures to be developed. Stress control measures for development headings have required the selection of roadway orientation, roadway sequencing, reinforcement density and pillar size. The monitoring of behaviour at a range of trial sites has confirmed significant improvements in development stability. Stress control measures for longwall extraction have required rational selection of longwall orientation and extraction direction. Where a mine layout design incorporating the optimum longwall layout design has not been possible, the use of sacrificial roadways has been successfully applied to protect key roadways from stress concentration effects. Comprehensive in situ

Jan 1, 1992

By Battino S

ABSTRACT' The high gas emissions associated with coal extraction at some-Australian collieries have provided a need to investigate the methods used to predict these gas levels and the vent- ilation requirements for gas dilution. It is generally accepted that the introduction of longwall extraction in particular is associated with complex ventilation planning problems. These problems are made much more severe when the colliery introducing longwalls is already facing high gas emissions even during the development stages. A forecast of likely gas emissions during the longwall mining process indicated possible ventilation problems in maintaining the necessary ventilation levels to satisfy the statutory gas limitations for various production rates. Although there are sound principles used in world recognised methods of gas emission prediction a new approach developed from the findings of the Barbara Experimental Mine in Poland appears most suitable for Australian conditions. This has been applied to an Australian colliery preparing for longwall mining using statistical methods for air

Jan 1, 1983