Search Documents

By Davies B, Rogers A, Grainger A, Todd J, Brenman R, Jones L, Horton B, Eager L

Research into the control of diesel particulates (DP) has been. conducted by BHP Coal for more than 7 years. Personal monitoring of employee exposures (n = 480 full shift samples) conducted at nine underground coal mines has indicated that the exposure of the workforce ranges from less than 0.1 to 2.2 mg/m3 of DP dependent on job type and mining operation. Approximately 50% of the mass of DP captured is elemental carbon (EC) which is the species currently being considered by some international regulatory authorities as the exposure standard. Five technologies for controlling DP were investigated in a combination of studies conducted in an above ground simulated tunnel, in a special controlled section of underground mine roadway and validated by application in standard coal mining operations at Tower Colliery. Tests conducted under controlled conditions indicate that dependent on the type of fuel in use, the introduction of low sulphur fuels can reduce DP levels in return airways by up to 50% and in actual mining situations a reduction of 20% can be achieved in exposure of the workforce. In addition, subjective responses from the workforce indicate that exhaust emissions from low sulphur fuels provide lower irritation and a more pleasant aroma. The use of water filled scrubber tanks reduces the level of DP emissions by 25%. Chemical decoking of engines resulted in a reduction of 20% in DP in return airways. A commercially available non-flammable disposable dry exhaust filter constructed from synthetic organic fibres with an operational lifetime in excess of 20 hours was found to reduce DP exhaust emissions by 80%. Investigations have indicated that the use of increased ventilation to control DP levels particularly in multiple vehicle situations does not follow a simple dilution factor and in some instances compliance with current regulatory requirements may not produce the required reduced exposure levels. The results from single component control strategies provide considerable reduction in exposure to DP, however the most efficient and cost effective control methodology is the use of a combination of individual systems modelled to operations conducted at each mine.

Jan 1, 1998

The traditional concept of optimum drill and blast is that it is achieved when ore is produced at the lowest unit cost and, because of the complexities of most mining operations, represents a band which extends either side of an overall cost m

Jan 1, 1998

By Dawes S

Efficient roof control in colliery operation is a factor that must be maintained for· the maximum reQovery and economic extraction of the mineral. It must be carefully considered in each of the following stages in the life of a mine.1. The primary development and the first working of the mine.2. The maintenance of access roads, intake and return airways.3. The extraction of pillars.FACTORS IN ROOF CONTROLThe main objects of roof control are: The support of the roof in working places, the relief of roof pressure from the workings during pillar extraction, and in some instances the prevention of subsidence of the surface.The support of the roof during development operations and first working, and the subsequent maintenance of these is influenced by:-1. The depth of the seam below the surface.2. The thickness of the seam.3. The dip of the seam.4. The condition of the roof and floor.5. The method of extraction-mechanical or by hand.6. The method of. working-Iongwall or bord and pillar.7. The availability of material.As a general rule, the pressure exerted by the superincumbent strata may be taken as one pound per square inch for each foot of cover, and the crushing strength of coal as 1,500 to 2,000 lb. per square inch; this, of course, varies, but from these figures it may be assumed that seams below 2,000ft. in depth are liable to crush. If any part of the seam is removed, added weight is thrown onto the remaining coal. It is therefpre essential that for effective working this extra weight must be removed or supported as soon as possible.The outstanding principle in the support of mining excavations is to ensure that the supports are set as soon as possible after the natural support has been removed.Where a system of bord and pillar is applied, the early setting of supports reduces the extent to which the roof bends, thereby reducing the liability to ·tension fractures at the centre of the road.

Jan 1, 1947

Tholeiitic metabasalts comprise at least five geochemically distinct mafic volcanic associations of Late Palaeozoic age within the Gympie Province, southeast Queensland. Geochemical features indicate that parental magmas of the various metavolcanic suites were generated in contrasting tectonic regimes, although each of the suites shows some affinities with eruptives from convergent plate margin settings.Basalts from the Highbury Volcanics of the Gympie Group are island arc tholeiites (IAT) formed during an immature stage of eruptive activity in an intra-oceanic arc. They are unique among the analysed metabasites in possessing high Zr/Nb (Zr/Nb - 30) and very high Ba/Nb, and as well as low Ti/V, Ti/Zr and Ti/Y. These features are explicable solely in terms of contributions from a depleted, convecting upper mantle source, and large ion lithophile element (LILE) enriched fluids ascending from subducted oceanic crust.

Jan 1, 1990

By J Player

Big Bell Mine started experiencing relatively large mining related seismic events, and accompanying rockbursts, from February 1999. Twelve rockbursts damaged access development from February 1999 to June 2000, with severe damage extending for up to 100 m along footwall drives. Five seismic events associated with the rockbursts were recorded by the AGSO, measuring 1.9, 2.2, 1.7, 2.4 and 2.2 on the Richter scale. These events affected 485 and 460 footwall drives in August and November 1999 and 535 footwall drive in June 2000 (drive level nomenclature is equivalent to the depth below surface and RL). After the third event (July 1999) it was apparent that the seismicity was not a once-off phenomenon. This (sudden) onset of seismicity required management to implement a series of precautionary measures:to ensure the safety of the workforce, to maintain continuity of production, and to reduce rockburst damage rehabilitation. The measures included extended re-entry periods and exclusion zones in high-risk areas, improved rockburst resistant support systems in areas prone to damaging seismic activity and improved support systems in areas prone to shakedown damage. A full-scale minewide ISS seismic system was ordered in October 1999 and commissioned in February 2000. A portable eight-channel CSIR-Miningtek system was installed at short notice as an interim measure in August 1999. This CSIR system covered the northern producing stopes, where the majority of the rockbursts had occurred. The objective of the seismic monitoring was to monitor relative activity and to determine trends with regards to time and location. MAP3D numerical modelling was used to investigate the relationship between seismicity and various combinations of stress components to assess the relative seismic risk in both current and proposed working areas. This information is used to determine where and at what stage in the mining cycle the rockburst resistant support is required. Analysis of the seismicity has determined two distinct modes of seismicity û small-scale localised, high frequency events in high stress areas and larger events related to shear along previously intact foliation surfaces. This paper includes a summary of the seismic history, seismic data analysis, support system design, mine design adjustments and management action to minimise the effects of seismic activity at Big Bell Mine.

Jan 1, 2000

By N TassT, J Cyr

At the East Sullivan site, wood wastes covering the abandoned mine tailings impoundment prevent sulfide oxidation by creating an anoxic environment. The addition of coarse ligneous wastes and their high permeability favour infiltration, resulting in a water table rise that maintains most tailings under water saturation and thus provides an additional protection against sulfide oxidation. Moreover, high infiltration allows a more rapid flushing of acid prone groundwater generated prior to the cover placement, which could cause acid mine drainage over a long period of time. Finally, the pore-waters under the cover are characterised by a strong reducing potential, high alkalinity, and near neutral pHs. These conditions favour sulfate reduction and base metal precipitation as sulfides and as carbonates. Pore-water composition monitored from 1992 to 1998 showed a significant Fe2+ decrease, following cover placement. Thereafter, the restoration strategy capitalised on the alkaline and reductive properties of the waters underlying the wood-waste cover. An original treatment of acid effluents, based on the recirculation of water discharging around the impoundment through the organic cover, was implemented. In 2002, the recirculated water from May to October had a mean pumping rate of 240 m3/h, for a total volume of 800 000 m3. Data gathered near the dispersal zone from 2000 to 2002 show that despite the recirculation of acid water (pH ÿ3), the pH decreases by only one unit from 7 to 6, during the recirculation period, ie from May to November. However, alkalinity decreases from 800 to 100 mg/L-CaCO3. Despite this decrease, the alkalinity is back up to 800 mg/L-CaCO3 the following May, thanks to sulfate reduction. From 2000 to 2002, Fe2+ concentration in the pore waters near the dispersal zone is maintained below 2 mg/L. Evolution of surface water quality suggests that the contaminated groundwater flush is completed in the north and north-west area of the impoundment; the east sector is under recovery, while the south sector remains the most problematic. A wood-waste cover, besides limiting sulfide oxidation, can fill the role of alkaline reducing barrier for the treatment of these acidogenic waters, until a balance between acidity and alkalinity in the effluent is reached.

Jan 1, 2003

The Malvern Hills coal project is now in an advanced stage of development with the stripping of overburden from above former underground workings in which a 3 m seam of subbituminous C coal with very low ash and sulphur was previously mined. The main seam dips at 45¦ to the south-east, along with other adjacent potentially recoverable thinner seams, and the strike extent of past coal mining in the Malvern Hills approaches 10 km with most extraction by underground methods. Overburden and interburden is predominantly weak mudstone, with only very minor sandstone, whilst a 1 - 2 m thick veneer of Last Glaciation loess covers the area. The coal product from the present mine site will supply the local industrial market, with production planned to peak at about 20 000 tpa. Settling pond design has been based on several different approaches, including an estimate of likely inflows from the contributing catchment of about 5 ha under predicted storms having a ten year recurrence interval. A pond of about 1000 m2 in area has been constructed with its invert in mudstone bedrock, and soil slopes have been lined with lime-stabilised clayey loess silt incorporating a gravel armour layer. The pond outflow takes place via a 2 m high 1.8 m diameter concrete dewatering tower, with a skimmer arrangement to lower the pond by approximately 500 mm between storm events. The overflow water discharges to the main stream above a natural wetland, which will act as a secondary polishing pond, and this is to be enhanced in conjunction with the neighbouring forestry company. Discharge consents specify turbidity and pH as the controlling criteria, and both will be monitored at the settling pond discharge point as well as at the entry to the main stream. Investigations to date indicate that the pH of water exiting from previous underground workings is in the range 6.8 to 7.2, and that acidic drainage will not be an issue with this mine site. No dispersive clays have been identified in assessing the overburden and batter materials, although erosion during storm events is expected and all drains will ultimately be routed through the main settling pond to ensure adequate control of runoff-generated sediment. Reestablishment of vegetation on cut and fill batters remains a priority, and ongoing monitoring will ensure satisfactory long-term performance of the pond system.

Jan 1, 2003

By G Chitombo, G Lewis

The knowledge of the expected run of mine (ROM) fragmentation during the feasibility study of a green field site is essential for the design of downstream crushing and milling processes. However,the prediction of blast fragmentation can be a challenging process due to the uncertainty related to the blast design and rock mass parameters. In general,a number of possible blast designs are considered in a feasibility study,with factors such as bench height and blasthole diameter influencing the design. Rock mass parameters are normally derived from a limited number of geotechnical diamond drill cores. Although diamond drill core can provide detailed information concerning intact rock strength (unconfined compressive strength and point load),it provides limited structural information to predict the in situ block size distribution of the rock mass. The in situ block size is an essential input to the prediction of the fragmentation distribution, in particular the coarse end. This paper outlines the methodology of blast fragmentation modeling undertaken for a green field feasibility study at the Riska gold deposit in Indonesia. The favoured milling process for the feasibility study was dump leaching,with no crushing of the ore material extracted from the pit. For this reason,blast fragmentation was a critical issue to be addressed by the study. A range of blast designs were considered with bench heights and blasthole diameters ranging from 4 m to 7 m and 76 mm to 102 mm respectively. Rock mass data was obtained from 19 diamond drill cores across the deposit (total drill length approximately 2200 m). Intact rock strength was estimated from qualitative strength descriptors,while the in situ block size distribution of the rock mass was estimated from the Rock Quality Designation (RQD) of the core. The methodology of fragmentation prediction involved a number of steps including the estimation of rock mass parameters from diamond drillhole data including the estimation of the in situ block size, delineation of blast domains within the deposit,and the assessment of the impact of various blast design parameters and rock mass variation on the predicted fragmentation distribution. The modelling process for the Riska green field site highlighted the need for additional rock mass data to be collected post feasibility stage and once the development of the mine commenced.

Jan 1, 2004

By A Dix

Fire suppression systems are but one of the many technologies currently available to manage operational tunnel risks. However, the actual reasons for their use are often shrouded in mischievous discussions of the marketing variety.The international tunnelling community still stands divided on the merits (or otherwise) of fire suppression systems. For some the debate focuses on their cost compared to the theoretical benefits they bring to human safety.Long standing concerns about their potential adverse effects in an emergency are often at odds with the experience from tunnels which use them. High installation and operational costs are cited as reasons not to use them, yet toll road operators and insurers increasingly use them as a risk mitigation strategy for toll revenue protection.Fact or fiction, myth or reality, should such systems be seriously entertained or are they just another expensive gadget in the escalating array of expensive toys for modern tunnels? Ultimately this presentation argues that they have their place as a risk mitigation measure to achieve a range of objectives. The exact circumstances for their use ultimately fashioning their design and operational characteristics. This is an abstract only. No paper was prepared for this abstract.

Mar 8, 2011

How do you initiate closure planning for a mine site that is on the doorstep of a major community without generating the extremes of panic or complacency? That is the question that is faced by Australia's largest gold mine, the Kalgoorlie Consolidated Gold Mines (KCGM) Super Pit in Kalgoorlie-Boulder. KCGM's Community Relations Manager, Danielle van Kampen, will reveal the lengthy closure planning process that is in train to alert yet not alarm the community about the future of the Super Pit and to generate discussion on issues of importance. What will happen to the 'big hole' that generates both mining and tourism dollars for the City of Kalgoorlie-Boulder as its anticipated closure date of 2021 comes closer? How do you communicate a constantly evolving closure date? Although the process may generate more questions than answers, the project will be discussed at length and with the added benefit of independent community recent research in the form of the public 2009 Closure Consultation and the KCGM 2010 Social Impact Assessment. This is an ABSTRACT ONLY no paper was prepared for this presentation.

Jun 1, 2010

By K D. Tuckwell

The Treasurer, the Hon Wayne Swan, has nominated ‘maximising our advantages’ from ‘Mining Boom Mark II’ as the focus of the 2011/2012 Australian Budget. Australia therefore requires a bolder and better integrated economic reform agenda if it is to convert current strong demand for mineral commodities into lasting prosperity that benefits all Australians. Lasting prosperity, well past 2012, will only be achieved if Australia can effectively reverse a decade-long deterioration in the minerals industry productivity performance due largely to capacity constraints that inhibit growth. This requires improving the efficiency of energy networks, transport infrastructure, water markets, health and education services, access to skilled people and by streamlining costly, inefficient project approvals’ processes. The common thread that holds this economic fabric together is the importance of having the right people using the most appropriate technology within the correct policy framework.In December 2010, employment in the minerals sector stood at 187 200; 21 per cent higher than one year earlier, 15 per cent higher than the industry employment peak prior to the global financial crisis in 2008 and 14 per cent greater than anticipated by industry modelling published in 2008. Managers and professionals make up approximately 15 per cent of the total workforce, yet minerals-related higher education programs (mining engineering, metallurgy and geoscience) continue to be chronically underfunded, requiring direct industry subsidies of more than $25 M over the last decade. Also, the publicly-funded Vocational Education and Training (VET) sector continues to fail the industry in the delivery of quality training programs. Importantly, the industry is a key driver of economic activity in regional and remote Australia and is the largest source of private sector employment for Indigenous Australians who comprise up to a quarter of employees in certain locations.This presentation looks at what our industry and country need to achieve to ensure we have the right people for the challenges ahead. **This is an abstract only. No paper was provided for this abstract.**

Nov 22, 2011

With the next mining boom looming, the industry will once again struggle to meet skills needed as the current generation boomers are set to retire. In order to meet these needs it is going to need to focus on what underutilised human resources - in particular women - want!   Women comprise around 14 per cent of the mining workforce, compared with a 45 per cent participation rate in the work force overall. Within the industry, women still make up only one per cent of trades people, eight per cent of operators/production employees, 12 per cent of engineers and 11 per cent of executive management.   It may be worth pointing out that mining has an age profile skewed towards the older end of the spectrum. When it comes to employee retention, what women want may be a good starting point to examine, more broadly, what all employees might want (but are too afraid to ask!).   Women in mining want the following: To be scrutinised for their work and performance, not their personal lives, appearance or relationships. True pay equity. This is addressed at lower levels between companies but at professional levels the salary differentials begin to appear and little is done to identify why this continues to be the case. Recognition and acceptance that women can have different work-styles, and that diversity of work-styles is an asset to be nurtured not a threat to be neutralised! Recognition that a more diverse workforce demographic that better reflects society at large will assist the company in its dealings with many diverse stakeholders from society at large. For employers to recognise that a career break to accommodate caring responsibilities does not mean that an employee's commitment to progressing their career is any less than that of someone who has not taken a career break. Similarly, for employers to recognise that working part-time for to accommodate caring responsibilities does not mean that an employee's commitment to progressing their career is any less than someone who works a more traditional roster. Access to affordable and quality child care compatible with mining rosters in mining towns. Zero tolerance for bullying and harassment, and workplace cultures that promote respect and safety. This is an ABSTRACT ONLY no paper was prepared for this presentation.

Jun 1, 2010

Energy is central to respond to critical stakes on human and industrial development requirements as well as on climate change. The increase of the share of carbon-free energy sources in the global supply mix will help to reduce significantly greenhouse gas emissions (GHG) as power generation accounts currently for 41 per cent of these emissions from the energy sector. In this energetic mix, nuclear and renewable energies are complementary, the first more focused in the baseload power generation whilst the second is well suited for decentralised power generation. In this context, AREVA's goal is to enable everyone to have access to a cleaner, safer and more economical energy. Regarding nuclear energy, AREVA's strategy is to capitalise on its integrated operation model, which groups together fuel cycle and nuclear power plant construction, aiming at building one third of the new nuclear capacities and securing the fuel cycle supply chain for its existing and future customers. Therefore, the front end of the uranium fuel cycle, from mining to the fabrication of fuel assemblies, has a key role in the sustainability of the nuclear industry. The replacement of the current capacity and the entrance of new countries on the nuclear power generation might lead to a significant rise of uranium demand by 2020. In order to be prepared in time, AREVA defined an ambitious industrial program to expand mineral reserves, increase the production of uranium concentrates, replace the conversion capacity, build two new uranium enrichment plants, one in France and one in the United States and upgrade its fuel manufacturing plants. To support the front-end industrial activities in the short and long term, AREVA invests on a portfolio of R&D projects to find out solutions to meet customers' needs, to improve its competitiveness and to develop new concepts and solutions to anticipate future market evolutions. In particular, some important technological challenges in mining must be surmounted to develop cost-effective methods to explore and exploit low grade deposits while creating sustainable solutions for reducing reagent, water and energy consumptions. In this lecture, an overview of the industrial investments of AREVA in the front end of the uranium fuel cycle and some highlights on its R&D major axis will be presented. This is an abstract only. No full paper was prepared for this abstract.  

Sep 13, 2010

By C Young

The identification of Critical Risks, their associated Critical Controls, and the implementation of processes to ensure their ongoing management can be difficult and resource intensive. Answering the following Critical Risk Management related questions can be challenging: • What is a Critical Risk? • What is a Bow-tie Analysis and when should it be used? • What is Critical Control? • How is the effectiveness of a Critical Control assured, and how is this measured? • Who is responsible for managing Critical Controls? • What are the implications if a Critical Control is not effective? It appears that in the mining industry’s efforts to implement the Critical Control Management Process outlined by the International Council on Mining and Metals (ICMM), instead of embedding an integrated, well understood, value adding process, we have instead created a resource hungry monster that is poorly understood by numerous layers of the organisation.

May 5, 2022

By K Zhao, H Gong, B Li

Health and safety are the first priority for Australian minerals sector. Australia has a global reputation in the mining industry. However, accidents occur every year. Legislation and regulation are important to prevent the accident from occurring, so do the new technologies. It is sad to witness the collision incident persisting and the long called collision avoidance system (CAS) is still not widely used in underground mines. The main reason is that the existing systems are still not advanced enough. The current CASs utilise GPS, infrared, ultrasonic, RFID, Radar, electromagnetic etc have their limitations and disadvantages. For instance, GPS is widely used in a surface mine, but it cannot be applied in underground mine; Infrared and electromagnetic have the false positive problem.

Sep 1, 2024

By A Tsoy

This abstract describes long-term mining schedule optimisation approach that may be suitable for complex marginal projects and is based on modern scheduling techniques. CITATION: Tsoy, A, 2018. Strategic mine schedule optimisation, in Proceedings Complex Orebodies Conference 2018, pp 91–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By S Sullivan

The key skills for a competent geologist are observation, documentation, analytical thought and the ability to communicate. These attributes have served the geological world for the past two centuries since the field of geology was separated out from natural philosophy. The understanding of the structural setting, lithologies, alteration and 3D distribution of the target mineral species are essential precursors to resource evaluation and potential economic extraction. The advent of artificial intelligence and machine learning has matured to the point where observation by dedicated sensors and analysis by customised AI algorithms can replace manual processes and deliver credible results. In combination with analytical data such as assays, various sensors now collect physical properties of rocks which are used as proxies for mineral identification and rock mass classification. These sensors include X-ray and infra-red spectra, magnetic susceptibility, gravity/density, EH/pH measurements, conductivity, colourimetric readings, porosity, fracturing and fracture intensity. Analysis using machine learning techniques trained using known data sets can determine rock type classification, rock density, quantification of grade/quality attributes, mineral alteration, weathering and geotechnical attributes such as rock quality. This type of data relies on calibration and quality control of a variety of different types of electronic hardware. The resulting data is non-additive, has error ranges and will be suitable for consumption by fast AI methods providing probabilistic analysis. A second stage could include geometallurgical constraints to provide an ‘extractability index’, which is of more interest to miners than pure geotyping. Using resultant interpreted geological criteria, 3D domain models with spatial attributes will be built.

Sep 1, 2024

By D Osborne

Current mineral extraction and valorisation activities still have a strong focus on the ‘delivered product(s)’ which might be a bulk commodity such as metallurgical coal, hematite, bauxite, etc., and mineral concentrates such as metal sulphides, oxides, and carbonates; precious metals, such as gold, silver and PGMs, REEs or battery metals; halogen salt forming elements; or industrial minerals, which are non-metals including crushed rock, sand, and gravel etc. With the current focus on tailings disposal the pushback has been to seek alternatives to the currently ‘conventional’ disposal method via increasingly higher risk tailings settling facilities (TSFs) with a changing focus towards ‘dry disposal’. Whichever option is selected, the alarming trend is the increasing cost and ESG impacts. An emerging approach is to pose a focusing question ‘Is there anything else passing into the tailings stream and/or disposable waste streams which could be recovered and pass into the product revenue stream? All of the above ‘primary’ process streams offer opportunities for increasing recovery and offsetting some of the disposal costs. Some secondary opportunities are already being pursued, such as REEs and battery metals from base metals deposits, but other opportunities are still being overlooked, such as building materials and soil conditioning pellets. These potential ‘new’ product streams can also utilise other mining and domestic wastes such as smelting slags, glass waste, plastic waste etc. This paper will address these opportunities and provide examples including process approach, economics and some of the current barriers that exist, which are holding back progress on such initiatives.

Sep 1, 2024

By D L. Kennedy

Many aspects of the physical layout of manufacturing plants and storage facilities for explosives are governed by so-called quantity-distances tables. Both the British and the American tables were originally derived from an analysis of the injuries and the building damage documented by an early 20th century compilation of significant accidental explosions. However, progressive changes in explosive process technology and in building techniques have reduced the relevance of much of this historic data set. Extensive scientific research has been conducted over recent decades to characterise the potential injuries and damage from accidental explosions under more modern conditions. This presentation will showcase some of this research.**This is an abstract only. No paper was provided for this abstract**

Nov 8, 2011

By R Hao

Uncertainties in large open pit geotechnical modelling has been a major concern for slope stability analysis. The level of confidence in the in-put assumptions, such as structural and rock mass model, dictates the modelling results to some extent. This article is to detail a case study of Kalgoorlie Consolidated Gold Mines (KCGM) regarding a predicted inter-ramp failure on an as-built pit walls by a 3D numerical modelling. Significant concerns were raised across site and multiple preventive plans were considered. After intense data collection work, it was confirmed that the risk of failure had been overestimated. The case study has improved the understanding of geotechnical data in-put and has enhanced the process of creating and updating geotechnical structural models at KCGM.

Jun 22, 2022