Search Documents

By T R. Gibbons, I Grayand

Geotechnically massive strata may lead to a host of problems during longwall mining. These include windblast on initial goaf fall, sudden loadings on powered supports, periodic weightings, fractures that may propagate to surface, and extreme subsidence problems. It is essential to identify these problems prior to mining and to appropriately deal with them. The problem is essentially that the rock mass does not breakup evenly and when it does so it tends to produce large blocks which may suddenly move. The rock types that produce these problems tend to be massive sandstones, massive siltstones and sometimes igneous sills. The fundamental problem with these is that they do not breakup readily. This is because the ratio of stress they are subject to compared to their strength is low. Thus, the shallower mines with lower stresses are more subject to this problem than deep highly stressed ones with similar strength rock.

Nov 29, 2022

By C E. Gawith

The Waihi underground mining operation currently mines epithermal veins ranging from two metres up to ten metres in width using a ‘Modified Avoca’ stoping method. This method consists of longhole bench stope mining at 15m to 18m sublevel spacing. The bulk of production drilling and blasting is top down with the extraction length of a typical stope panel nominally being 18m to 20m along strike. A stope panel is usually taken in two blasting cycles followed by the remote bogging of the stope ore. The panel is backfilled in-cycle using unconsolidated waste rock material which is tipped into the void from the upper level using a Caterpillar R2900 or R1700 sized underground loader. The underground mine first commenced production in 2008 and up until 2016, as was typical of many open stope mining operations at the time, an underground loader was used to place a waste rock bund at the top brow of the open stope. This rock bund was the principal means of protecting people and equipment from this hazard. In 2016 there was a fatality at the mine when a loader that had been tasked with building this rock bund fell into the stope void. Immediately post incident all mining and processing operations were suspended for a week to allow colleagues to grieve, to observe cultural protocols and to begin the investigation into this event. During this period senior operators, supervisory and technical staff developed an innovative system which used steel bollards to protect this open edge. With development over the following months this bollard system has eliminated this hazard from the Waihi underground mine.

Mar 15, 2021

By Y Peng, D J. Bradshaw, G Long

As copper reserves deepen, they are becoming increasingly less pure. Penalty elements such as arsenic, antimony and bismuth are occurring in increasing concentrations. Environmental issues with smelters are leading to increases in penalty rates for these elements such that some concentrates may become difficult to sell. Arsenic concentration in Rosebery copper concentrates during 2010 varied between 3000 and 8500 ppm. Arsenic levels above 5000 ppm can preclude import to some customer countries. Optical mineralogy has indicated that arsenic in Rosebery copper concentrates is most commonly associated with tennantite (Cu12As4S13) in solid solution with tetrahedrite (Cu12As4S13). In addition, silver reports to concentrate as freibergite (Cu12As4S13 ). A reduction in arsenic content will therefore lead to a concurrent reduction in the silver content.A literature review by Long, Peng and Bradshaw (2012) indicated that arsenic bearing minerals could be removed using potential controlled flotation. Some success in reducing the amount of arsenic had also been reported using either roasting or chemical depression using reagents such as lime and cyanide. Due to the location of the Rosebery concentrator adjacent to world heritage listed temperate rainforest, the use of a roaster or cyanide was immediately discounted. Lime is already used as a reagent in the Rosebery flow sheet, so could be considered as a potential arsenic depressant.In order to determine a method of separating out the high arsenic bearing minerals, two series of flotation tests were conducted. The first series investigated the effect of pulp potential on the recovery of copper, silver and arsenic minerals; a second series investigated the effect of pH, froth depth and regrind.CITATION:Long, G, Peng, Y and Bradshaw, D J, 2012. Production of a low arsenic copper concentrate at MMG Rosebery, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 347-354 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By R Strand, B Usher

Environmental compliance and mine designs are increasingly including assessment of flows and water qualities as a key driver to decision-making over life-of-mine. Integrated site-wide water quality models linked to dynamic water balances have been used for regulatory submissions, feasibility studies, operating mines and mine closure studies. These models, developed in GoldSim, link aqueous chemistry to the physical system of the site-wide water balance. Geochemical mechanisms included are determined from geochemical characterisation and site water monitoring, depending on the data availability at each site. External geochemical modelling using PHREEQC, version 2 (by D?L?Parkhurst and C?A?J?Appelo) and Geochemists Workbench (GWB), (by C?M?Bethke and The Board of Trustees of the University of Illinois) identifies the most important geochemical processes to be included in the model as a series of geochemical mechanisms which include source term loading rates, pH-buffering and equilibration of water quality. Water balance components include seasonal flow variability; waste facility water storage and system lags; run-off variability; milling processes and tailings production as a function of ore types; simulation of automated and scheduled maintenance of settling ponds; water re-routing for water treatment and freshwater demand, usage and storage.Case studies illustrating the use of these models for regulatory submissions and mine feasibility studies in a variety of climatic and regulatory environments show the utility and applicability of these models. Site-specific examples of these models developed by Klohn Crippen Berger Ltd are currently used at operating mines across the world. One of the larger mines where this is used is a mature poly-metallic mine in South America where the model has aided mine managers in understanding how various planned initiatives and potential water options will result in changes to flows and water quality. It is used regularly to inform water and waste management to minimise impacts to the receiving environment as a consideration of both flows and concentrations. The mine has also used the model in support of water treatment design, regulatory submissions and mine closure planning.Further examples of feasibility and operational/compliance assessment in arid and strongly seasonal environments for planning, regulatory and closure consideration of mine wastes and pits have shown the utility and usefulness of these approaches for a range of mining operations at various stages of mine life.CITATION:Strand, R and Usher, B, ?2014. Integrated site water balances and water quality models for decision-making over life-of-mine, in Proceedings Life-of-Mine 2014 , pp 271–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By Z Endut, T F. Ng, G H. Teh, J H Abdul Aziz

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Gold mineralisation at the Penjom gold deposit in the Central Belt of Peninsular Malaysia is hosted in structurally-controlled quartz-carbonate veins that display a variable degree of overprinting events under a ductile-brittle regime. Mineralised veins are categorised into two main types: shear and extension veins. Shear veins are interpreted as forming during the fold and thrust episode (D2 event) along the bedding and the Penjom Thrust ore zone. The shear veins are associated with discordant extension veins. In addition, NE- to NNE-trending splays and Penjom-Thrust-parallel reverse-dextral and locally NNW to N–S reverse-sinistral faults overprint earlier vein events, forming a new episode of extensional veins during the D3 event. This is mostly at the fault contacts of intrusives, either as shallow-dipping or vertical-sheeted stockwork or brecciated veins. At least two episodes of faulting comprising D4-D5 are evident, which postdates the main episodes of veining and mineralisation. This is indicated by a series of late episode N–S-trending sinistral and oblique to normal faults that transect and displace the Penjom Thrust and the folded footwall sequence at low angles, and are interpreted to be responsible for intensive vein deformation along the Penjom Thrust and displacement of the orebody. Structural interpretations of mineralised veins suggest that the veins were formed under a compressional to transpressional regime, with later post-vein displacement in a transtensional to extensional regime. Vein formation in response to deformation observed at Penjom reflects regional structural deformation within the Central Belt of Peninsular Malaysia and specifically along the Bentong-Raub Suture zone.CITATION:Endut, Z, Ng, T F, Abdul Aziz, J H and Teh, G H, 2015. Style of veins in Penjom gold mine, Malaysia – implications for gold mineralisation and structural episodes, in Proceedings PACRIM 2015 Congress, pp 507–514 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By E R. Ramanaidou

Two unknown iron ore samples were found by a geologist from Ok Tedi Mining Limited copper, gold and silver mine at an old wharf site dedicated to a 1970s drilling program in Lake Murray in Papua New Guinea (PNG). These iron ore samples could not come from a PNG mine and it was decided that a study should be undertaken to understand their origin. Lake Murray is the largest lake in PNG with a total surface area of 647 km2. It has a high-water 2038 km long convoluted shoreline with seasonal water level changes (Osborne, Kyle and Abramski, 1987) and it is located around 200 km south of the Ok Tedi mine (5°13’25”S, 141°09’37”E). The petrology, mineralogy and chemistry of two Fe samples (Ok Tedi 1 and Ok Tedi 2) included optical microscopy, X-ray fluorescence (XRF) analysis and a comparison with worldwide iron ore deposits. The two rock samples were cut to produce two subsamples: (1) a polished thin section; and (2) a pulp that was used for XRF analysis including major, minor and trace elements. Ok Tedi 1 and Ok Tedi 2 were petrologically and chemically compared to a range of known iron ore samples from Australia, Brazil and South Africa. The petrological study of Ok Tedi 1 indicates that it is composed of granoblastic recrystallised hematite and the overall texture is uniform without any obvious original ‘sedimentary’ texture. Ok Tedi 2 is a ‘specular’ or platy hematite with recrystallised and fused grains. Using both petrological and chemical clues, the two Ok Tedi samples likely originated from the Iron Quadrangle in Brazil.

Sep 18, 2023

By E Ferrow, R Herbert, M E. Malmstr, M Fuchs

The study of microbial sulfide oxidation and oxidation rates of tailings requires the use of sterile control samples in laboratory experiments for comparison purposes. The need for sterile tailings sand is also apparent in the study of microbial communities and processes. This study compares six different methods with regard to sterilisation efficiency and investigates chemical and mineralogical changes in the samples as the result of sample treatment. In addition, the effect of sterilisation on mineral weathering rates is also studied. The efficiency of the different methods with regard to sterility is estimated by most probable numbers (MPN) of both sulfur and iron oxidising bacteria. The sterilisation methods that were compared are: washing with sterile water, washing with ethanol, applying antibiotics, repeated heating to 70¦C, autoclaving, and γ-irradiation. There are several possible drawbacks with the different methods, including the risk of an applied chemical acting as a substrate for micro-organisms in the system, and the risk of altering the tailings. The results show a substantial difference in sterilisation efficiency between the treatments. For example, autoclaving, repeated heating, ethanol and irradiation efficiently kill micro-organisms, rendering an undetectable amount of bacteria after one month of incubation, whilst washing with water exhibits virtually no microbiological effect, with a bacterial content comparable to the control. The use of antibiotics for sterilisation ranks intermediate: the lag-phase was twice as long in the antibiotics treatment compared with the controls. X-ray diffraction, optical and electron microscopy, M÷ssbauer spectroscopy, and mineral magnetism indicate no significant change in the bulk mineralogical composition. However, X-ray photoelectron spectroscopy analyses show that with some of the treatments, sulfides are partially oxidised, as indicated by the formation of sulfate and partially û oxidised sulfur species at the tailings surfaces. Aerated batch weathering experiments performed on sterilised tailings samples and untreated controls indicated that while the initial rates of element (S, Fe, Cu, Zn, Mg, Na, K, Ca) release may differ between the samples, over the course of ~100 days of experiment at pH 2 and room temperature, the rates declined toward a similar value for all samples. To conclude, there does not appear to be one perfect method for tailings sterilisation. Autoclaving and heating damage the mineral grain structure and oxidise the sulfide surfaces. Ethanol, antibiotics and rinsing greatly alter the pore water chemistry through the washing procedure. In addition, ethanol and denatured antibiotics might serve as a substrate and also, in the case of antibiotics, adhere to mineral surfaces thus obstructing chemical reactions. Irradiation seems to be the preferable method on an overall basis, although the formation of surface Fe3+ was suggested by M÷ssbauer spectroscopy.

Jan 1, 2003

By J Theiler, B Beamish

Spontaneous combustion hazard assessment from an environmental impact perspective is not well understood and is seldom given due consideration in environmental impact statements. In surface mining operations, self-heating, leading to spontaneous combustion may occur when rock units containing reactive metal sulphides and organic carbon are disturbed by mining operations and exposed to the atmosphere. When these rocks are present self-heating will occur in situations where the rate of heat generated from oxidation reactions exceeds the rate of heat lost to the surroundings. The processes and mechanisms that lead to spontaneous combustion events are varied and generally complex. To effectively manage spontaneous combustion in surface mining operations, it is necessary to characterise the spontaneous combustion propensity of the geological materials involved. Until recently there has been no testing procedure for assessing the propensity of waste rock to spontaneously combust that has been adopted by industry. However, new developments in adiabatic test methods have proven successful in determining the self-heating behaviour of coal (Beamish and Theiler, 2015) and coal containing reactive pyrite (Beamish and Theiler, 2017). These adiabatic test methods have now been modified to assess the incubation behaviour of waste rocks and can be used for their spontaneous combustion characterisation in advance of mining (Beamish and Theiler, 2016). The new method provides a practical means to establish the likelihood of developing a spontaneous combustion event for the specific site conditions. This paper presents examples of the use of a cost effective first pass filter for assessing spontaneous combustion potential of waste rock based on geochemical data from four surface mines. This is supported by adiabatic Incubation Test results for three of the mines and visual examination of cores for one of the mines. CITATION:Theiler, J and Beamish, B, 2018. Valid spontaneous combustion hazard assessment for surface mine environmental impact statements, in Proceedings Life-of-Mine 2018, pp 64–67 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

Standard petrographic profiles for many Permian seams from New South Wales and Queensland have been drawn up. The standard profiles of seams of the same age and from one or more coalfields were used to compile an idealized or type seam sequence for those coals in which more than half the seam profiles were similar to one another. A marked similarity existed between at least 7 of the 10 type seam sequences formed. The configurations of the vitrite-plus-clarite contents of the plies of 95 per cent of the seams could be formed from different arrangements of 3 basic sequences: (i) a two-ply sequence with a lower vitrite-rich and an upper vitrite-poor ply; (ii) a two-ply sequence with a lower vitrite-poor and an upper vitrite-rich ply; and (iii) a four-ply sequence of 3 plies with vitrite-plus- clarite decreasing upwards, terminating in a vitrite- rich ply. The third basic sequence was very similar to a succession described for some British Carboniferous coals. Eighty per cent of the Australian Permian coal seams studied began with the first (i) basic type of sequence and are interpreted as originating in peat- forming areas which became progressively drier. More than half the seams were formed in an area with a stable depositional surface level which was subject to oscillations of small amplitude.. Many (30%) were formed in an area with a steadily rising depositional surface level.

Jan 1, 1969

The discovery of gold mineralization at the Manhattan mercury mine, Napa and Yolo counties, California in 1978 was the result of applying a new exploration ore deposit model in a region previously unprospected for gold. This discovery, the McLaughlin gold mine, owned and operated by Home-stake Mining Company, is a classic epithermal mercury-hot springs-gold deposit currently producing approximately 7,776,000 grams of gold annually.The exploration program that led to this discovery was based on a mercury-hot springs-gold genetic model. The model was developed using basic knowledge of ore-forming processes plus careful field observations made during examination of many known precious metal districts in. the Western U.S.A. Theoretically, hot spring systems could host gold deposits and, indeed, gold in these environments had been recognized for years. However, at the time of the McLaughlin discovery, it was not known to occur in sufficient quantities to inspire geologists to explore hot spring systems specifically for gold. Field observations recognized the presence of hot spring deposits and mercury mineralization asso-ciated with precious metal districts, (Bodie, California being a type example), and this associ-ation prompted the development of a hypothetical model. Subsequent exploration activities were directed towards the examination of mercury mines and prospects as potential targets for gold deposits. The model envisioned hot spring deposits (sinter) containing mercury mineralization at the surface with anomalous gold values grading downward into significant ore grade gold values.

Jan 1, 1990

FOR some time it has been recognised by the Metallurgical Staff that the presence of pyrite in the ore was adversely affecting the grades of the flotation concentrates.Following experimental work, it was decided to change over from the acid circuit in the mill to an alkaline circuit. The following description sets out the procedure adopted, -and the results obtained when such change-over was made.The Zinc Corporation ore consists mainly of galena, marmatite, calcite, and quartz, with smaller quantities of pyrite, fluorspar, and rhodonite.A clean specimen of marmatite picked from the ore assayed 53.4% zinc, and 10% iron, with no lead or insoluble. However, as zinc concentrates have been, at times, produced in the plant assaying over 53% zinc, and with only 8.7% iron, apparently the picked specimen of marmatite did not represent an average composition.The average would probltbly be between 8 and 9% of iron, and from 53.5 to 54.5% of zinc. It is obvious, therefore, that from this ore it is not possible to produce zinc concentrate of a higher grade than this average figure.In the Colorado School of Mines Quarterly for April, 1928, Vol. 23, No. 2, on page 47, we find the following statement:As the zinc in the ore exists as marmatite, which contains approximately 54.5% zinc and 10% iron, 49% zinc in the concentrate may be considered high.This statement refers to the ore treated in the Sullivan concentrator, owned by the Consolidated Mining and Smelting Company of Canada Limited.

Jan 1, 1930

By H Kim, M J. Sun

Global steel companies are actively combating climate change by reducing carbon emissions. Traditional steel production, using the blast furnace (BF) – basic oxygen furnace (BOF) process, heavily depends on coal and emits substantial CO2. To mitigate this, companies are transitioning to the more eco-friendly DRP (direct reduction plant) – EAF (electric arc furnace) process, which lowers CO2 emissions. This study quantitatively evaluates the impact of increased hydrogen consumption on the carbon footprint of product (CFP) through an analysis of direct reduction process heat and mass balances. The study prioritises a comprehensive material balance based on mass conservation principles. The heat balance is calculated using differences in enthalpy through state energy properties, avoiding heat consumption. Validation using operational data from Hyundai Steel Dangjin works’ blast furnaces shows close alignment between calculated results and actual data, with less than 1 per cent error. This methodology facilitates a detailed analysis of the direct reduction process, offering insights into its feasibility and efficiency. Analysis of the operational impact by increasing the hydrogen ratio demonstrates reduced CO2 emissions and increased heat requirements due to the endothermic nature of hydrogen reduction, in contrast to the exothermic CO reduction. Possible solutions include raising reducing gas temperature or enhancing flow rate. The study effectively utilises designed heat and mass balances to assess material quantities and thermal balance under different operational conditions. It lays the foundation for the initial direct reduction process design, aiding in deriving and optimising operational parameters. Additionally, it provides valuable insights into the challenges of increased hydrogen, contributing to the production of greener steel by addressing these issues.

Aug 21, 2024

By M A. Noppé

"Investors and other stakeholders assessing the risk, opportunity and relative value associated with a resource project need to appreciate the project in its correct context. Errors, omissions, biased reporting or conflicting information in project reporting may lead to a misinterpretation of technical and financial results, resulting in biased estimates or assumptions on project value.This paper provides a simple ‘Resource Project Framework’ for presenting a project’s status that may be readily benchmarked against other similar projects and to illustrate the stages required to advance the project outcomes to higher levels of certainty. The framework draws on definitions and guidelines readily available in various resource industry reporting codes and public company reporting requirements.The framework assesses three key areas for placing a resource project in its correct relative context, namely:the project development stagethe confidence in the Exploration Results, Mineral Resources and/or Ore Reservesthe level of accuracy, precision and confidence in the technical and economic studies supporting the reported results or options for the project.The application of the Resource Project Framework is illustrated using two project examples, one from publicly reported company project releases and the other for two development projects.CITATION:Noppé, M A, 2016. A framework for presenting and benchmarking resource projects, in Proceedings Project Evaluation 2016, pp 260–274 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By J H. Kyle

Cyanide is a significant cost in gold processing, as well as an environmentally sensitive issue. It has been suggested that precipitation of cyanide from leach liquors as copper-iron-cyanide compounds such as Cu2Fe(CN)6 may account for part of the total cyanide consumption. This may be especially true for ores that are rich in both copper and iron minerals. Ammonia addition has been shown to decrease the cyanide consumption by copper. Cu2Fe(CN)6.xNH3 precipitates have also been postulated to form during conventional cyanide detoxification processes, using oxidants such as SO2/air, with ammonia arising as a breakdown product from the oxidation of free cyanide. The present work has examined the conditions under which such precipitates may form, particularly in gold plant process and detoxification liquors. Ammonia and pH were found to have a large effect on the extent of precipitation. The compounds that were formed were found to comprise mainly Cu2Fe(CN)6.7H2O, as well as a range of NH3-bearing variants. The stabilities of the various precipitates are important from an environmental perspective. The long-term stability of copper ferrocyanide precipitates in tailings dams may be a problem under alkaline conditions and when some free cyanide is present, elevating the measured total cyanide in solution significantly. Case studies including data from actual plants are also considered, and the importance of these effects is reaffirmed from these results.

Jan 1, 2000

By B Banerjee, H Masoumi, X Shen, S Raval, D Tannant

Structural mapping of pit walls can be performed using digital images and photogrammetry software, but the performance is limited by weather and environmental conditions including dust, rain and light. On the other hand, active sensors such as terrestrial laser scanners (TLS) and total stations (TS) suffer from vertical orientation bias and occlusions when persistent discontinuities dip at the same angle as the scanner line-ofsight. The recent development of the compact light detection and ranging (LiDAR) systems has made it possible to mount these sensors on unmanned aerial vehicles (UAVs) or drones which offer the potential to overcome limitations that are inherent in existing mapping systems. This study details the research involving integration and application of an advanced UAV-LiDAR system for structural mapping of a highwall. A state-of-the art laser scanner with an inertial measurement unit (IMU) and real-time kinematic global positioning system (GPS) was integrated on to a UAV. The system was first tested in a laboratory condition. Then the UAV-LiDAR system was employed to map a highwall of a coal mine. The planned flight trajectories tested the system at variable distances from the highwall face and at various speeds. The raw data collected from individual sensors were fused, filtered to remove noise, and segmented to produce a surface scan model. Finally, the point density and surface coverage were measured using the surface scan model of the highwall. The parameters were compared with equivalent measurements computed from a reference TLS data. The study demonstrates the capabilities of a UAV-LiDAR system to generate accurate and occlusion free data for mapping highwall geological structure with very quick and efficient flights in the field. CITATION:Raval, S, Banerjee, B, Shen, X, Masoumi, H and Tannant, D, 2018. Evaluation of a UAV-LiDAR system for mapping geological structures in an open pit highwall, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 496–503 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Mason P, Waller C

The Phase I electrowinning system at KCGM's Fimiston Operation utilised the well proven technology of electrowinning precious metal values onto steel wool followed by calcining and direct smelting to bullion. The above process, while reliable and successful, was to some extent labour intensive. The Williams Mine in Ontario, Canada had published conditions under which precious metal values are electrowon onto woven stainless steel and directly removed using high pressure sprays. The current paper describes the testwork which was carried out to check the applicability of the Williams criteria to KCGM eluates arising from the elution of highly loaded carbon from the calcine circuit and lowly loaded carbon from the float tails circuit. Information is also given on the commissioning and operational experience which occurred.

Jan 1, 1996

By M Csar

The Nicolsons Find gold project is located 35 km southwest of Halls Creek in the east Kimberley. It was discovered in the late 1980s by John Nicolson and Stuart Skoglund, when high grade gold mineralisation within outcropping gossanous quartz reefs was found. The area has produced a modest 28 150 ounces of gold over two brief mining periods in 1996 and 2002 - 2003. Indicated and inferred resources as of September 2011 stand at 1 384 000 t at 5.58 g/t Au for 248 500 ounces of gold.The project is situated within the Halls Creek Orogen. Principal host units are metasediments and volcaniclastic sediments of the Koongie Park Formation. Minor mafic units are also recognised. Immediately east of these units, emplacement of the loadstone granite is believed to have provided the structural setting for the later gold mineralising event.Mineralisation is hosted within a broad, brittle-ductile arcuate shear zone about the western contact of the Loadstone granite. In the Nicolsons Find area, the shear zone strikes north-northeast and within the shear zone, gold is hosted in a series of narrow, quartz rich veins up to 200 m in strike length, plunging moderately to the north-northeast. To date, mineralisation has been drilled to a depth of 360 m below the surface. The veins are stepped or en-echelon in nature with low gold values towards the quartz vein limits where compression is inferred and higher grades present in the dilational body of the quartz veins. Gold is fine grained and can be present with or without associated sulfides. Sulfides are generally minor and consist mainly of arsenopyrite with traces of chalcopyrite, pyrite and sphalerite. Where present, sulfides are generally indicative of higher gold values.CITATION:Csar, M, 2012. NicolsonÆs Find gold project, East Kimberley, Western Australia, in Proceedings Narrow Vein Mining 2012 , pp 31-36 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

A hidden asset in most exploration and mining activities is data. Common practice involves the spending of large amounts of money to discover, define and prove the viability of a mining project. Some organisations have used operations research analysis and internal costing methods to allocate a value to their data and to compare the costs of data maintenance to other more tangible activities like plant and equipment maintenance. Those organisations, which do not undertake such an analysis often, have little knowledge or understanding of the extent and the worth of their data. Often the organisations lack of knowledge and understanding of the data is indicated by their failure to fully exploit or realise their opportunities. The focus of this paper is to discuss new technologies that optimise the management and security of collected and derived data. The technologies discussed are components of the software systems acQuire and MineSight.

Jan 1, 1999

By J Theiler, B Beamish

The presence of reactive metal sulfide minerals in waste rock contributes to the hazard of spontaneous combustion in dumps, as these minerals react with air and water entering the dump at ambient temperatures to form various mineral products and significant heat. This reaction series can also be an initiator of self-heating of carbonaceous material present in the waste rocks if sufficiently high temperatures are reached. Characterisation of these reactive minerals has primarily been to assess the risk of acid mine drainage, which is not necessarily an indicator of spontaneous combustion risk. No systematic testing procedure has been adopted by industry to assess the spontaneous combustion propensity of the waste rock. As a consequence, the principal management strategy for spontaneous combustion has been a reactive approach of dealing with events as they arise.Recent advances in adiabatic oven-testing have enabled more definitive assessment of the spontaneous combustion propensity of coals, including the quantification of the accelerating influence of reactive pyrite (Beamish and Beamish, 2011, 2012; Beamish, Lin and Beamish, 2012). This same test procedure has been used to assess the self-heating performance of metal concentrates and is therefore amenable to assessing the metal sulfide oxidation process from low ambient temperatures. The data obtained from such testing can be used to quantify the more prone waste rock sequences of a mineral deposit in advance of mining. This enables appropriate management planning for emplacement and long-term storage of waste rock in dumps.CITATION:Beamish, B and Theiler, J, 2016. Characterising the spontaneous combustion propensity of waste rock, in Proceedings Life-of-Mine 2016 Conference , pp 93–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By B Haase, R Saha

Conditional simulation (CS) has been extensively used in metal industry to assess uncertainty of geo metallurgical variables to build robust distributions around grade tonnages across different time horizons. Coal’s entry to nonlinear stochastic modelling is relatively new and this paper summarises the work done at BHP to enable its practical usage from production time frames to Life of Asset planning. CS in coal using Sequential Gaussian Simulation (SGS) is used to understand resource confidence around specific variables within pre-defined boundaries of spatially continuous domains for each coal seam. The variation between simulations for a given parameter reflects uncertainty. This paper demonstrates the use of CS to profile resource based upon agreed seam/parameter uncertainty thresholds which affect planning, forecasting, extraction and inform identification of key production risks and defining mitigation strategies. The end goal is to de-risk long-term plans by optimising infill data collection and improve stability in short-term planning through increased understanding of confidences locally rather than at global resource definition stages. The paper also briefly discusses the use of automated workflows and systems to minimise the time spent on the process to enable use in decision-making.

Mar 22, 2022