Search Documents

By M Fylak, R Wenda

Advanced preparation techniques open new ways for SEM and X-ray diffraction (XRD) investigations on hydrating cementitious systems. In this paper the early time hydration of Portland cement is studied with advanced cryo scanning electron microscopy techniques in combination with in situ X-ray diffraction and heat-flow calorimetry. The application of preparation techniques and analytical methods to Portland cement hydration are presented and discussed. Some aspects of hydration reactions are focused. The reaction products of the first minutes, changes in ettringite morphology, AFm formation during the deceleration period and the visualisation of C-S-H microstructures were special points of interest. X-ray diffraction analyses and Cryo-SEM images gave essential information about phase development, reaction kinetics, microstructure and morphology of hydration products. Portlandite, AFt and AFm phases were detected by in situ XRD. Cryo-SEM analyses enabled high resolution imaging and EDX-analyses of cement particles and reaction products. The results of the different analytical methods were compared to obtain detailed information about crystallisation processes and microstructural development during the first three days of Portland cement hydration.

Jan 1, 2008

By Francis R. S, Campbell J. J

Aberfoyle's Hellyer Division has filtered very fine flotation concentrates using two different makes of pressure filter. At the Luina concentrator a Larox pressure filter was used to treat a combined Pb + Zn or bulk concentrate. At the Hellyer concentrator two Lasta pressure filters are being used to filter copper/silver, lead, zinc and bulk concentrates. Operating parameters and performance at both operations are described. In both concentrators it was found that correct cloth selection was critical and that cloth failures contributed significantly to downtime. Thorough preventative maintenance progammes were required to ensure adequate availability of both makes of filter.

Jan 1, 1989

By D K. Miller, L W. Armstrong

In April 2006, Orica Quarry Services undertook an investigation to determine the likely vibration and frequency response of three water storage tanks to quarry blasting, immediately adjacent to the tanks. Of the three tanks that were studied, two are relatively tall with a æwineglassÆ shape; one is constructed of steel (4 ML storage capacity) while the other is constructed of concrete (2 ML storage capacity). The third is a ground-embedded concrete tank that is relatively squat and broad in shape (38 ML storage capacity). A vibration limit of 25 mm/s and an acceleration limit of 0.16 g were imposed on the tanks. However, this report shows that this acceleration limit, whilst having relevance to low frequency earthquake motions, is quite inappropriate for the high frequency blast vibrations that are typical in a quarry blasting environment. The investigation involved firing 11 single blastholes of known charge weights and distances from the tanks, and measuring the tank vibration response using blast monitors placed on and around each tank. Analysis of the data collected from the cement tanks showed resonant responses over a broad range of frequencies, with dominant and lesser responses in vertical and lateral motion recorded at 9.8 Hz, 12 Hz, 16.8 Hz, 17 Hz, 31.3 Hz and 38.1 Hz. Unfortunately, most of the data collected on the steel tank was corrupted by noise due to electrical sources and/or mechanical sources such as the water agitator inside the tank. Advanced Monte Carlo vibration models were then constructed using the single blasthole information. Knowing the resonant frequencies enabled the modelling of electronic delay sequences for the reduction of resonant vibrations. Ultimately programmable and accurate electronic delay detonators were deemed essential to allow blasting in relatively close proximity to the tanks while avoiding resonant frequencies. Three blast designs were modelled, ranging in maximum instantaneous charge (MIC) from 4 kg to 22 kg, and 60 holes to 160 holes. The modelling showed that two of the designs (using small charge weights) could be used no closer than 71 m from the storage tanks. This is based on a 90 per cent confidence level of achieving vibration levels within the 0.16 g acceleration limit, even though the velocity levels predicted to be generated at this distance were significantly less than the 25 mm/s limit. The third design incorporated larger charge weights and could be used for blasting at distances no closer than 220 m from the tanks. The present work, conducted in an operating quarry, demonstrates the usefulness of Monte Carlo waveform superposition techniques for the control and reduction of ground vibration (either velocity or acceleration) under restrictive environmental constraints. However, a discussion is also presented to demonstrate that it is somewhat restrictive to impose an acceleration limit based on the motion produced by low frequency earthquakes rather than the motion produced by high frequency blast vibrations.

Jan 1, 2007

By Bradford NL

The Isa Mine of Mount Isa Mines Limited produces 5.1 million tonnes of copper ore and 2.2 million tonnes of silver-lead-zinc ore from sublevel open stopes annually. Extraction of the narrow, steeply dipping silver-lead-zinc orebodies requires a strategy quite different to that used in the massive copper orebodies. A range of blasthole diameters, explosive types and initiation systems gives the flexibility needed to adapt open stoping to a variety of situations. Hole diameters from 70 mm to 200 mm are being used, with lengths of up to 100 m common for the latter.

Jan 1, 1982

Daily geological mapping of the Panguna porphyry copper/gold system since mining began in 1971 has provided a good basis for resource estimation and mine planning as the mine and estimation methods have advanced. Geology defined during evaluation and early mining has been substantiated and many smaller features have been better defined or identified. Breccias, pebble dykes, major structures and location of lithology contacts important to short term planning and long term pit slope stability have been defined. Correlation of copper and gold with breccia zones is quite striking and was not fully appre- ciated at the end of evaluation. Pit mapping geology, and diamond drill geology and assays, are now routinely added to a Geological Data base on computer, which forms the major geological data base for modelling the deposit. Geology from diamond drill logging, updated by pit mapping, and assays from diamond drilling updated by blast hole assays have been incorporated in a 45 bench deep 486 000 block computer based block model which forms the basis for long and short term planning. The introduction of pre-concentration scre- ening, based on the distribution of mineralisat- ion and fracturing, puts more emphasis on the definition of grade distribution at low concent- ration and on structures in the rock. Geostatistics is now used for resource estimation and has produced acceptable estim- ates. but these need to be refined, particularly in peripheral, low grade areas of the deposit.

Jan 1, 1987

The Savage River open cut magnetite mine is located in rugged terrain in densely rain forested northwest Tasmania. The mine and concentrating plant are both in the Savage River valley. Pickand Mather Incorporated (PMI) operated Savage River as an open cut magnetite mine between 1966 and 1996. Acid rock drainage (ARD) was first noted in the last ten years of the operation, leading to elevated concentrations of heavy metals downstream of the mine. When operations ceased in 1996, PMI returned the mine to the Tasmanian Government along with a remediation fund of $11.4 million. At that time, the assessed cost of remediation was in excess of $120 million. As a result of the ongoing ARD contamination and to facilitate both a new operation and effective remediation, Goldamere Pty Ltd negotiated an agreement with the Tasmanian Government in 1996, which resulted in the Goldamere Act and the Goldamere Agreement. The agreement has allowed Australian Bulk Minerals (ABM) to remediate the Savage River mine in conjunction with the Tasmanian Government while re-invigorating a previously closed mine by providing ABM with an indemnity against past pollution. ABM can configure its mine and waste planning activities to maximise remediation benefits without fear of future litigation for past mistakes. The effect to date has been the development of a long-term strategy to remediate the Savage River and short-term remediation works such as water management, which provide benefits to the ecosystem. After five years, the Savage River is no longer significantly impacted by ARD for 30 kilometres downstream and trout are now reported within the reaches of the mining lease. The arrangements between ABM and the Tasmanian Government are an example of a genuine WIN WIN situation where co-operative environmental management of the site results in significant improvements and where the æregulatorÆ and the æminerÆ are working together to achieve mutually beneficial goals. The end result is a significant benefit to Tasmania.

Jan 1, 2003

By Matthews SM, Gooding JE

N Longhole Open Stope at The Zinc Corporation Mine was developed in an area with large and continuous tension cracks. These cracks resulted fran widespread block subsidence into previously mined areas. The practical problems encountered and their solutions are discussed together with an outline of a new method of stope wall support using large diameter dowels installed sub-parallel to the stope wall.

Jan 1, 1985

ADDRESS BY THE PRESIDENT OF THE INSTITUTE (MR. C. H. MARTIN) IN PRESENTING THE CERTIF1CATE TO SIR GEORGE FISHER, C.M.G.Members of The Institute, distinguished guests, of which there are many, ladies and gentlemen, you are welcome.And might I add a special welcome to Lady Mawby and Lady Fisher and to Sir George's only son Peter, who with his wife, Betty and one of Sir George's three daughters, Helen, are present this evening, and also to Sir Maurice's son, Colin, and Colin's wife, Jay, also in our company.The family presence must surely be a great source of pleasure and satisfaction to all those so intimately concerned.It is hardly. necessary for me to state the sole and only rC'l.son for our presence here tonight, which is to conJer on Sir George Fisher and Sir Maurice Mawby Honorary Membership of The Australasian Institute of Mining and Metallurgy, and at the same time to acknowledge two people who have rendered great service to the mining industry albeit tinged with sadness to all of us in the knowledge that from now on their influence may diminish.

Jan 1, 1976

By Thompson AG, Cadby GW

The New Austrian Tunnelling Method (NATM) is a proven concept for the safe and economic construction of underground facilities. This is especially true for tunnelling activity where changing ground conditions are often encountered. However, the principles central to the NATM have gained only limited use within Australia, presumably due to the measurement process inter- fering with tunnel driving and the cost associated with instrumentation and interpre- tation expertise. The design and operating principles of two basic instruments are explained together with laboratory simulated test results and suggest- ions for use in an integrated NATM style approach to underground excavation and construc- tion. The two instruments monitor load in rock reinforcement and deformation in rock or primary and secondary linings. The instruments may be fitted with a miniature display module which outputs the measured parameter in engineering units directly. The design of the sensing components allows the instruments to be installed in various configurations suitable for routine performance monitoring, quality control, support element testing or detailed investigations. The display module which reduces the need for instrumenta- tion expertise should suit contractors and allow performance data to be obtained which quickly may be used to modify support procedures to suit ground conditions. When complemented by convergence measurements the devices enable most facets of the NATM to be implemented.

Jan 1, 1987

By Irving R. C

THE objective of the iron smelter is naturally the production of high quality iron at the lowest practicable cost. To enable this, large tonnages are put through the blast furnace, and, at the same time, the quality of the iron must be under definite control.The modern blast furnace enables these objectives to be attained. The description whieh follows sets out the general details of construction of such furnaces, and the operation at thc Broken Hill Proprietary Company's blast furnaces at Newcastle, New South Wales.The occurence of iron in many forms is so well known as to need no description. Modern civilisation may be said to be built on a foundation of iron, and, today, the production of iron and steel has beeome one of the world's industries.A short historical introduction will serve to show the evolution of the processes and apparatus since iron production assumed importance.There is no definite date fixed as to when iron was first made, or by what means it was first discovered. Perhaps prehistoric man threw iron bearing stone on to his fire, and these became reduced, Ieaving a soft metal behind, or more probably the first iron was of meteoric origin.There is evidence, however, to prove that it has been known for a period of 6000 years. Iron has been found in the Pyramids and its use was known to the early Eqyptians and later to the Hebrews, Assyrians, Greeks and Chinese. Following the Greeks, the Romans excelled in its extraction and uses in the manufacture of their instruments of war, and to this fact can largely be attributed the success of their many wars of conquest. As the Romans overran the rest of the then known world they carried the art with...

Jan 1, 1930

By Stewart R, Manson RA, Haig DW, Perembo RCB, Kruman B

Since the advent of plate tectonic modelling, the Ramu-Markham valley has been thought the site of a classical island-arc/conti- nent collision zone. In this interpretation the units south of the Markham Valley are held to be island are / micrcontinental mate- rial accreted to Australia and those north of the valley are thought to represent a separate Finisterre island-arc terrane. Recent remapping by the Geological Survey of Papua New Guinea shows: (1) there is no terrane boundary along the Ramu-Markham valley (2) the Finisterre Volcanics are probably part of either a fore-arc sequence or oceanic plateau obducted onto a microcontinent/ volcanic-arc composite terrane, accreted to the continental Australian plate. A new tectonic model is proposed for northern PNG and involves: (I) Eocene to Late Oligocene subduction below a microcontinent remote from Australia to produce the Sepik are and related intrusives, the Finisterre Volcanics (fore-arc or possible oce- anic plateau), together with the Alife blueschist. (2) obduction of the Sepik arc in Late Oligocene-Early Miocene times over the advancing Australian plate. This resulted in crustal melting, some of the products of which are the Mid- dle to Late Miocene Akuna and Bismarck intrusive complexes of the Maramuni arc. (3) obduction of the Finisterre Volcanics began in Early Pliocene times and continues today. (4) post-Middle Miocene mineralisation is the result of melting after obduction of the Sepik microcontinent.

Jan 1, 1997

By Jepsen L, Gifford M, Thomas G. S

Mine planning requires careful prediction of both the head grade and tonnage of mineralisation. As part of the planning process, operators of the Murrin Murrin nickel/cobalt orebodies (located in the Eastern Goldfields province of the Yilgarn

Jan 1, 1998

By T Amiconi

Ernest Henry Mining commenced operations on its copper-gold project in August 1997, some two months ahead of schedule and ten per cent ($35 million) under budget. The mine is located in the highly prospective Mount Isa/Cloncurry mineral district in north-west Queensland, approximately 38 km north-east of Cloncurry. The developer and operator of the project is Ernest Henry Mining Pty Ltd (EHM), an incorporated joint venture between MIM Holdings Limited (51 per cent) and Savage Resources Limited (49 per cent). The deposit is located approximately 40 km north of Cloncurry in North West Queensland and lies beneath a featureless black soil plain with no significant creeks or gullies cutting across the site. Vegetation is sparse and consists essentially of Mitchell grass with occasional low shrubs and trees. Up to nine million tonnes of ore and over 43 million tonnes of waste will be extracted each year from an open pit operation to produce approximately 350 000 tonnes of concentrate when in full production.

Jan 1, 1998

Lightweight polymer grids have recently been introduced to the mining industry. They are currently being used for roof and rib control, longwall shield recovery, safety guarding or barricade, highwall screening, internal reinforcement of gunnite/shotcrete applications, sub-base reinforcement, construction of steepened slopes, retaining walls, mine reclamation (i.e. erosion control, turf reinforcement), and in numerous mining waste related projects. These polymer mining grids utilize a strong, lightweight polymer, usually special grades of polypropylene or polyethylene. High tensile strengths are achieved by molecular orientation of these polymers in the manufacturing process. The first step in the manufacturing process is to extrude the polymers into thick continuous sheets. These sheets are then punched, and drawn into open grid structures. Aperture size and configuration are controlled by the geometry of the punched hole and the degree to which the grids are stretched. The drawing process is the key to the molecular orientation required for the tensile strengths. These long chain polymer molecules in their natural state have a random orientation. When stretched, the molecules are pulled into a parallel alignment, thus creating a lightweight product with tensile strength comparable to Steel.

Jan 1, 1992

By D Beck, E Jones

The measurement and management of deformation in underground excavations is a key responsibility of geotechnical and mining engineers. A critical aspect of these roles is to ensure there is sufficient ground support capacity for the expected demand.Current methodologies for monitoring deformation and ground support serviceability-limits require measuring displacement at distinct points, or using visual observations. These current methods limit the assessment to a qualitative interpretation of deformation across the entire excavation.Recent advancements of Light Detection and Ranging (LiDar) technology permit a new method for monitoring deformation that allow a full 3D image of extended sections of an excavation to be precisely scanned. The results from the comparison with subsequent scans provide valuable information on the magnitude, direction and extent of regions exceeding the ground support serviceability-limits. This new method now provides a quantitative assessment across the entire excavation being monitored.The implementation of regular scanning has been demonstrated to be highly advantageous not only at mines with swelling or squeezing ground, but also at mines with rapid seismic induced deformation. The use of LiDar technology as a routine deformation measurement tool for geotechnical and mining engineers (and further applications) are discussed in more detail in this paper.CITATION:Jones, E and Beck, D, 2017. The use of 3D laser scanning for deformation monitoring in underground mines, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 267–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

Proceeding from statistical data on the development of waste volume, an endeavour was made to characterise waste materials with regard to the applicability of treatments based on mineral processing. Many types of waste are characterised by a high heterogeneity. The separation processes used for processing raw minerals can also be used for separation of various waste mixtures. For some waste mixtures, differences in properties can be utilised for separation which are mostly less distinctive for raw minerals. State-of-the-art technology is illustrated with selected Examples.

Jan 1, 1993

Drag pick roadheaders and continuous miners have been applied in the coal mining industry for several decades, having replaced drill-blast methods as the primary means of excavating coal and coal-measures strata. The generally harder rock types associated with metalliferous mining have precluded the use of such machines in the past, however, developments in machine technology and increasing labour costs and environmental constraints suggest that there are now likely to be applications suited to the method. Metalliferous mining engineers are generally unfamiliar with the machines themselves and with the fundamental criteria controlling rock cuttability. This paper gives an introduction to the machines and the controlling factors.

Jan 1, 1987

By Leach B. G

A geostatistical study was made of diamond drill hole intersections within 18CC stope block at the C.S.A. Mine, Cobar, N.S.W. The stope block is located in 18CC orebody which is a massive sulphide - multiple vein, Copper-Zinc type, lacking clear definition on gangue mineralogy, base-metal assays and total sulphide considerations. Of the variograms constructed for inter- section width and copper, lead and zinc grades and accumulations, only zinc displayed behaviour amenable to model fitting and kriging procedures. Zinc grades were calcu- lated for sub-blocks comprising the total stope block and comparison with equivalent grades determined by traditional methods showed them to be generally less extreme in the highest and lowest grade sub-blocks. The total-block grades derived by the two methods were almost the same. It is suggested that the failure of copper to show variogram continuity might reflect the difficulty in defining the actual 18CC orebody, a proposition which is supported by the poor continuity in the variogram of horizontal width. In the case of lead the poor continuity may be due to the frequent manner of occurrence of galena as coarse grained patches of limited extent. The results of the study, did not provide a convincing reason to depart from the traditi- onal methods of grade estimation at the C.S.A. Mine.

Jan 1, 1979

This paper outlines the manner in which legislative control for tunnelling and allied operations has evolved, detailing Victorian experience. It examines the concept of mine managers as it relates to the industry and attemps to illustrate its benefits. The Victorian experience in relation to fatal and serious accidents is examined in detail, particularly in the allied art of trenching and examines the Krings system of trench lining support which is hoped will catalyse an increase of engineering expertise in this area. The paper concludes by demonstrating that safety awareness is not incompatible with production efficiency or economic viability.

Jan 1, 1981

Although developed primarily for sintering tantalum, the unit to be described can be used to heat-treat metals in the form ofa bar, wire or strip, by passing a current through them. The upper temperature limit with this type of heating is the melting point of the metal being heated.The unit was designed for vacuum work, but. various gases can be used if required.Briefly, the vacuum sintering furnace consists of a bell which is counter-balanced and may be lowered onto the brass base plate which holds the electrodes. A rubber ring seal is used for vacuum work. The lower flexible grips are bolted to the brass base plate which is at earth 'potential, while the other electrode passes through the plate by way of an electrically insulated vacuum seal. This upper electrode, the height of which can be altered as desired, the lower grips, and the bell are water cooled. The vacuum line to the pumps and a line to the vacuum gauges also lead from the base plate. The more important sections of the unit are described below.THE BELLThe unit was designed so that the bell could be lifted clear of the base plate and the electrodes, thus facilitating adjustment of the latter and the mounting of the specimen to be heated. A double walled steel bell, 20 in. high, with t in. cavity was used. The bell was fabricated from 10 gauge mild steel sheet using a double overlapping run of arc welding for all seams. A water inlet and outlet...

Jan 1, 1946