Search Documents

Diversity; what a wonderful topic. Diversity; the condition or quality of being diverse, different, varied to the point that the very word diversity means different things to different people. As one example of diversity the American Science Magazine (April, 1994) contained a light-hearted interview with Dr Noitall who was pushing his case for diversity.

Jan 1, 1996

This paper briefly describes the shaft, including sinking, steel sets and their installation, shaft equipment and winders.INTRODUCTIONThe New Broken Hill Consolidated Ltd. Service Shaft is a vertical concrete-lined circular shaft, 20 ft. in diameter with -steel sets spaced at 12-ft. centres. The diameter of 20 ft. was established as the minimum that would enable the shaft both to house the proposed hoisting and service equipment and to satisfy ventilation requirements as a downcast airway. The 12-ft. set spacing was based on South African practice in similar types of shafts.The shaft extends from the surface to 28 ft. below No. 22 Level, a total depth of 3,194 ft. Sinking was commenced in September 1946, and equipping completed in January 1955. Initially the shaft was sunk and concrete-lined to a depth of 52 ft., using a stiff-legged crane and clam-shell grab for mucking. Operations were suspended at this depth to allow the installation of the steel sinking head-frame, winders and ancillary equipment.Sinking and concreting were recommenced after four months and continued to a depth of 1,035 ft. 6 in., where the shaft connected with a pilot opening. The concrete lining was poured as sinking progressed and was piped from the surface to this depth, after which all concrete was lowered in buckets and discharged through a distributor suspended in the shaft. A cycle of stripping to the pilot opening and concreting was continued until the shaft reached No. 22 Level. From this level the remaining 28 ft. was sunk full size. All plats were cut and concreted as sinking progressed.

Jan 1, 1957

By P Rubie, B Morgan, J Russell, C Stewart

The relationship between efficient liner exchange, concentrator availability and concentrator profitability is well documented. Russell Mineral Equipment’s (RME) relationship with OZ Minerals’ Prominent Hill site personnel enabled sound collaboration between the two parties. Both parties worked together to identify the sources of productivity and efficiency loss and developed solutions to reverse them.This paper chronicles the identification of production inefficiencies and the resulting removal of mill relining from the critical path through the materialisation of mill relining optimisation strategies. Furthermore, this paper outlines other recent mill relining optimisation strategies developed by RME and tested at Prominent Hill, to demonstrate and achieve further productivity, efficiency and safety improvements.CITATION:Rubie, P, Russell, J, Morgan, B and Stewart, C, 2017. Mill relining optimisation – a story of collaboration, in Proceedings MetPlant 2017, pp 335–345 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

The Ediacara mineral field is classified as a Mississippi Valley type deposit with stratiform mineralization near the base of the Cambrian beds. Mineral deposition was contemporaneous with sedmentation and reerystallization, and mobilization took place after lithification of the sediments. Several mechanisms of deposition were possible.INTRODUCTIONThe Ediacara mineral field is located in the Mt. James Range approximately 300 miles north of Adelaide, about 12 miles west of Beltana railway siding and 10 miles east of Lake Torrens. It is isolated geographically from similar deposits of equivalent age and environment in the Flinders Range Province (Fig. 1). The climate may be described as semi arid with high summer temperatures and frequent dust storms. Occasional thunder storms are the main source of rain in the summer months.The exact date of discovery is unknown, but is believed to be about middle of the last century. Ulrich (1872) was the first geologist to report on the field. At that time only the southern portion of the field had been prospected (and abandoned). Although the prospects did not appear encouraging Ulrich advised prospecting of the shales and testing beneath the limestone.In 1888, Rosewarne, an Inspector of Mines, visited the Southern Workings and queried whether they were connected with some lode at deeper level or were merely bedded deposits. The first geological map with sections was drawn by H.Y.L. Brown (Brown 1892).Brown recognized three principal rock formations as dolomitic sandstone, kaolinised shales and sandstone, and quartzites and sandstone in descending order. These three basic units are still recognized. He recognized also the stratiform nature of the mineralization in the shales as a...

Jan 1, 1963

Using Mineral Maps to Rank Potential Processing Behaviour

Sep 13, 2010

Cadmium occurs in the Broken Hill Lode essentially as a camouflaged element, substituting diadochically for zinc in the sphalerite.Analyses of a series of zinc concentrate flotation products, prepared from samples of ore taken at intervals throughout the developed lengths of the several orebodies forming the lode, have revealed a pattern in the distribution of cadmium relative to zinc. This pattern appears to reflect the temperature and order of deposition of the several orebodies, and the direction of movement of the mineralizing solutions.INTRODUCTIONThis investigation into the distribution of cadmium in the several orebodies of the Broken Hill lode was undertaken by the Mineragraphic Section. of C.S.I.R.O. in conjunction with the Broken Hill Geological Research Committee, as part of a study of Broken Hill mineralization.It arose from the examination of cadmium and zinc assays supplied by Mr. T. A. Read, Chief Metallurgist of the Broken Hill South Ltd.; of experimental zinc concentrates prepared from localized samples of the No, 2 and No. 3 orebodies in the Broken Hill South Mine. These assays suggested that the two orebodies were characterized by distinctive ZnjCd ratios.In view of the possible sigmficanc'e of such a difference, comparable data were sought from each of the other mines. The necessary samples of ore were collected by the geological staffs of the several mines. The preparation of separate zinc concentrates and lead concentrates from these samples, and their assaying, was conducted by Mr. Evan Hardy, for the North Broken Hill Mine, and its assodated leases, and by Mr. D., Swan, under the direction of Dr. J. C. Nixon, for the Zinc Corporation and New Broken Hill Consolidated Mines. Additional tests on the Broken Hill South Mine were made by Mr. C. W. Reilly, under the direction of Mr. T. A. Read. The samples were...

Jan 1, 1955

Judicious placement of a range of geotechnical instruments was employed at the Tasmania gold mine, Beaconsfield, Tasmania, as a key strategy in the monitoring of rock mass conditions over the past four years. The range of instruments employed included vibrating wire stress-meters and hollow inclusion cells to monitor changing stress conditions, resistance wire and multipoint borehole extensometers to monitor the impact of stress changes on the integrity of the rock mass, and instrumented cable bolts and threadbar bolts to monitor the static and dynamic impact of rock mass changes on the installed ground control system. Initially the monitoring was of a qualitative nature, monitoring change from the time of installation. The value of the output was considerable when considered in relation to the ongoing seismic record which was also being monitored. It was clear from the seismic record and the monitoring results that stope blasting was the primary trigger for changing rock mass conditions. However, it was unclear how well observed behaviour was reflecting conditions anticipated by elastic numerical modelling. The latter had predicted significant stress increase in the near field of man-access footwall development. Qualitative monitoring and visual inspection did not support the modelling prediction, and this led to a program of quantitative measurement being undertaken. Measurement of the absolute stress condition in the backs of footwall development immediately adjacent to monitoring hollow inclusion cells provided the benchmark for tracking quantitative stress change. The program provided insight into the evolution of principal stress field magnitude and orientation in relation to rock mass change observed with extensometers and instrumented ground control elements, as well as providing a degree of calibration between the elastic numerical modelling and the virgin stress field. Calibrated monitoring data has also provided a useful benchmark for finite element modelling which is to be used for future mine-wide design.

Nov 25, 2010

IN this paper an attempt is made to describe the sluicing operations on the tin fields of north-eastern Tasmania. No claim is made to completeness, for much of the ground has already been covered, and nothing is to be gained by needless repetition. On this account some portions of the subject have obviously received but attention in order that others may be rather more fully dealt with; for instance, referring to the accuracy of various methods of valuing alluvial deposits, particulars of efficiencies, and water duties on both overburden and drift; also, the system of recording water distribution, &c. The plans of the tin-streaming shed, sluice and feed race, and overburden tail-race represent types of the most modern design.GEOLOGY. The principal alluvial dcposits being worked at the present time are situated either in the ancient or modern bed of the Ringarooma River or its tributaries. This river flowed in a north-easterly direction, receiving numerous tributaries on either bank...

Jan 1, 1910

A hard lump char containing only 4 to 5 per cent ash, 0·25-0·30 per cent sulphur and a trace of phosphorus has been produced from Latrobe Valley brown coal by slow drying and carbonization of ordinary industrial briquettes at temperatures between 7000 C and 14000 C. The briquette char can be made with a variety of reactivities by varying the maximum temperature of carbonization; the higher the temperature, the lower the reactivity. The strength of the fuel compares favourably with metallurgical coke made from black coal, though it may not be quite so resistant to abrasion. Experiments in a small experimental cupola indicate that it will make a satisfactory fuel for use in iron foundries. It may also find extensive application as a smokeless fuel in other branches of industry and in household heating appliances.INTRODUCTIONVictoria, like South Australia and Western Australia, is apparently without 'significant deposits of black coal of coking quality but there are huge reserves of brown coal of high moisture content (60-66 per cent) in the Latrobe Valley (well over 20,000 million tons have been proved) and there are other important deposits in the south central portion of the State (Herman, 1952).For three decades Victorian industries, including a few metallurgical firms, have been using the briquettes made at the Yallourn factory of the State Electricity Commission of Victoria (S.E.C.). These briquettes, having a moisture content of about 15 per cent and a calorific value of approximately 9,500 B.T.U. per pound, are satisfactory for certain grate-type furnaces but they are not suitable for use in cupolas of other shaft furnaces because they disintegrate badly on rapid heating.

Jan 1, 1956

Some of the problems associated with drill core evaluation of alluvial tin deposits and correlation with plant-scale recovery are discussed. Panning churn-drill cores on site tends to undervalue such deposits because of failure to recover completely all the available liberated cassiterite, and secondary gravity processing may also fail to give an accurate determination of potentially recoverable tin. However, by using a combination of heavy liquid separations, x-ray fluorescence analysis for Sn, and normal methods of reflected and transmitted polarized light microscopy, a quantitative assessment of alluvial material can be carried- out. The information obtained may include the liberation characteristics and distribution with size of the cassiterite, the nature and quantities of the various gangue minerals, and the amount of potentially recoverable cassiterite in the material as compared with the amount locked with light gangue minerals and hence difficult or impossible to recover. In addition, an analysis of the efficiencies of the various gravity processes, such as panning, jigging, and tabling, used to determine "recoverable tin" in the alluvial material, can be carried out. A detailed example is given of this type of investigation, in which an assessment was made of a churn-drill core from Uncia, Bolivia.

Jan 1, 1970

By M Kozikowski

The primary purpose of these investigations is to determine dewatering requirements and likely impacts associated with mining operations. Standard aquifer testing techniques were carried out at multiple locations within the Ord Range near Pardoo, Western Australia. Aquifer properties of an oxidised haematite orebody were calculated from test pumping data conducted in five fully penetrating test bores. Hydraulic properties of the Ridley magnetite orebody were calculated based on short term constant rate pumping tests, and packer tests. Packer tests were conducted in undeveloped and uncased exploration holes and diamond core holes. The new data sheds light on the hydrogeological properties of this previously unexplored region of Western Australia.Aquifer testing procedures for each bore included a preliminary step test followed by a constant rate test. Recovery data were collected in each bore over a period of four to six hours. Prior to testing, background water levels and water samples were collected in a network of monitoring and exploration bores to establish baseline water levels, gradients and water quality. Water quality within the bedrock of the Ord Range varies from 2000 to 5500 mg/L TDS whereas water quality within the alluvial sequence of the De Grey River is highly variable (400 to 2500 mg/L TDS), but is predominantly brackish with some water of potable quality which is used to supply Port Hedland. Test pumping supports the conceptual hydrogeological model that consists of a pod like orebody (aquifer) surrounded by low permeability waste rock (BIF), with very weak hydraulic connection to the adjacent alluvial systems. Calculated hydraulic conductivity from test pumping data across Pardoo ranged from 0.01 to 59 m/d, depending on deposit tested.A groundwater model was used to simulate dewatering required in proposed pits and to estimate the impact of dewatering on the surrounding shallow alluvial aquifers. Test pumping and numerical groundwater flow modelling indicate the proposed below water table pits can be successfully dewatered utilising in pit dewatering production bores. Yields from individual dewatering bores will reduce with time due to the reduction in saturated aquifer thickness.Based on the numerical groundwater modelling and field investigations the likely impacts to the adjacent De Grey River alluvial aquifer system (within the Priority 1 De Grey River Water Reserve) resulting from mining and dewatering activities is considered minimal. Recalibration of the groundwater model will be undertaken once several months of dewatering data are available.The aim of this paper is to present a range of aquifer parameters derived through standard aquifer testing techniques for an area previously unexplored in terms of hydrogeological characteristics. It is the goal of the authors to provide this comparison data set for future work in similar geologic media.

Jan 1, 2009

Up to 19 chemical parameters were studied in flotation pulps in six Australian lead-zinc concentrators with the aim of obtaining a better understanding of the nature of, and changes in, the chemical environment. This paperdiscusses pH, redox potential, and oxygen concentrations, which were all measured continuously.Two plants operated at natural pH in slightly acid circuit and one at natural pH in alkaline circuit, and pH was stable at all these plants. In two plants varying amounts of cement fill were present in mill feed and pHwas variable. At the other plant pH was controlled with soda ash and lime.Redox potentials became more positive as the pulp passed through the plant. The minimum change was 20 mV and the maximum about 250 mV. Potentials tended to be variable at any point early in the circuit, but were more stable later on. In some plants reagent additions had no noticeable effect on redox potentials. However in the two plants operating in acid circuit the redox potential of .zinc rougher feed was markedly affected by changes in copper sulphate addition rate. Sodium sulphite additions had an effect at other plants.Oxygen concentrations in grinding circuits tended to be low (30 per cent of saturation) and very variable. Flotation was usually conducted in pulps at least 90 per cent saturated with oxygen. Addition of sodium sulphite had a marked effect on oxygen content in one plant, but less effect in two others.Statistically significant relationships were found in some plants between pH and redox potential, redox potential and oxygen saturation, and oxygen saturation and pH.Improved control of copper sulphate and sodium sulphite additions could result from applications of this work.

Jan 1, 1970

Uranium ore at Sleisbeck, N.T., occurs as lenticular bodies associated with zones of bleached carbonized schists lying between walls of closely folded quartzite. The ore consists mainly of uranium micas with Borne pitchblende.INTRODUCTIONThe Sleisbeck uranium prospect is about 70 miles E. of Pine Creek, and 160 miles S.E. of Darwin (Fig. 1). The prospect consists of a well-defined, E.-W. trending line of hills, about I! miles long. The line is composed of 3 major hills called the Eastern, Central and Western hills, with minor interconnecting hills and outcrops (Fig. 2).

Jan 1, 1955

By J W. Hedenquist

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Epithermal deposits (Au or Ag dominant, ± base metals) form within ~1 km of the surface in volcanic belts, both arcs and rifts, with the different tectonic settings reflected in distinctly different characteristics. Within arcs, deposits are typically intrusion centred and commonly associated with hypogene advanced argillic alteration, both in lithocaps and as halos to shallow or proximal portions of some veins; such alteration is coupled with processes that form porphyry Cu-Au deposits at depths of ~1–3 km. Introduction of metals is related to the subsequent phyllic-stage overprint; if this fluid rises to the level of the lithocap or into epithermal veins, Au mineralisation with Cu or Ag may occur, associated with sulfate minerals or muscovite. By contrast, Au-rich (both low Ag:Au ratio and bonanza grade) colloform quartz veins form at shallow depths in volcanic rifts, typically within a few hundred metres of the surface, with clay halos and topped by silica sinter if the palaeosurface is preserved. The geologic variability in volcanic belts, including host rocks, structures and hydraulic gradients, means that many epithermal deposits vary from the end-member features of the principal styles. Effective exploration requires familiarity with end-member styles as well as potential variations, plus the mineralogical indicators of palaeotemperature (eg evidence for erosion depth, fluid flow channels). This knowledge helps the geologist in the field to imagine what might be buried and where, and how to best test the target with drilling.CITATION:Hedenquist, J W, 2015. Recent developments in understanding of and exploration for epithermal deposits in volcanic arcs , in Proceedings PACRIM 2015 Congress, pp 11–16 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Perhaps one of the most important conferences or symposia which our Institute has conducted, was the joint Aus. LM.M./AJ.M.E. meeting held in Canberra in May 1978, with the theme International Resource Management (Woodcock, 1978).We were privileged to witness active participation in the meeting by outstanding personalities from the mining and metallurgical industries of Australia and New Zealand, the United States of America, Canada and the United Kingdom and to hear addresses on subjects of international significance to the mining and metallurgical industries.Our Institute is one concerned with professionalism.The principal objects of The Institute as described by our founders include, "promoting the arts and sciences connected with the economical production of the useful minerals and metals, and the welfare of those in the industries, by meetings for social intercourse, and the reading and discussion of professional papers, and to circulate by means of publications amongst its members and associates, the information thus obtained".Sir Maurice Mawby (1968) said in his Presidential Address to the Institite, "the most important aspect of these objects was the promotion of the arts and sciences of the mining industry".Why is it then, that a large proportion of the papers given at the meeting in Canberra dealt with world wide social aspects of the mining and metallurgical industries, rather than the technology, the arts and sciences of mining and metallurgy as principal factors in international resource management?The answer is quite simple of course, and that is that the social and political factors are the principal factors which create the demand for basic raw materials and in the long term determine the costs and prices of the commodities which our professional abilities are drawn upon to produce.

Jan 1, 1979

Measurement of densities, susceptibilities, permanent magnetization, and calculation of demagnetization factors has allowed computer modelling of gravity and magnetic data over the Middleback Range iron formations of South Australia. As well as providing structural information, the study emphasizes the effects of weathering on the interpretation of magnetic data.

Jan 1, 1975

This paper summarizes the progress of geological exploration at North Broken Hill Ltd.The North Mine orebodies occur in knots of minor folds on a simple limb structure which is itself highly folded, giving rise to two distinct orebodies pitching N. at av. 42° down to 2,920-ft. level, where the pitch steepens to near vertical as a result of complementary shear movement on the Globe-Vauxhall Crush Zone.The lack of adequate marker beds and top and bottom relations makes the resolving of the complex structural environment of the orebodies most difficult.To test the deeper ground of each side of the De Bavay Fault on the 2,600-ft. level the footwall drive was extended 3,556 feet and over 20,000 ft. of drilling completed from three transverse fans, only one of which intersected the orebodies due to steepening of pitch.The problem of locating the North Mine orebodies N. of the DeBavay Fault remains speculative because the exact position of them S. of the fault is still unknown. Exploration beyond the fault in the search for ore had two lines of mineralization to consider, an eastern one through Cosgroves-Round Hill, long regarded as the continuation of the main lode, and a western one passing through Silver Hill Silver Peak.From surface 45,000 ft. of drilling was completed in five sections, establishing that the structure was dominantly synclinal with a flatdipping E. limb, the W. limb and adjoining structures being involved in the Globe-Vauxhall Crush Zone. Mineralization, though weak, was remarkably persistent but the economic mineralization exposed at surface has not persisted with any continuity.Deep exploratory drilling below the bottom level (3,370 ft.) has established high-grade ore to a depth of 4,095 ft. and also has proved its existence within the Globe-Vauxhall Crush Zone.INTRODUCTIONThis paper summarizes the progress of geological exploration at North Broken Hill Limited from the inception of the Geological Department in 1941 until the end of 1955. The writer has drawn freely on departmental records for the period prior to 1947.

Jan 1, 1956

By Gaulton R

The Commission maintains a data base first computerised in 1957 and containing information from over 18 000 boreholes located mainly in the Latrobe Valley area. Some of the borehole derived information dates from the turn of the century, although most of it has been collected as a result of Commission investigations conducted over the past 40 years. The Resource Data Base contains not only information gained directly from the drilling itself but includes the results of chemical and physical testing on many hundreds of thousands of samples retrieved from boreholes. Replacement value of the Resource Data Base has been estimated to be around $200 million, and it's integrity and accessibility is clearly of paramount importance, not only to existing mining and power generating functions but to the future evaluation and use of the vast brown coal Resource.

Jan 1, 1992

By Reeves M

A review of the literature available in English on kriging and geostatistics is given with the references cross-classified by their subject matter for convenience and ease of use.

Jan 1, 1979

By A B. Christie, S C. Cox

Effective land-use planning requires accurate knowledge of mineral resource potential. Mineral companies during reconnaissance exploration, feasibility investigations and mine development also use this type of analysis. The Institute of Geological and Nuclear Sciences is undertaking a two-year project reviewing the resource potential of the West Coast of the South Island of New Zealand. Spatial prospectivity models have been developed as part of this resource assessment process, using computer based statistical pattern recognition techniques to delineate areas that are prospective for mineral deposits and to test deposit genesis models. Digital GIS data-sets of mineral occurrence were correlated against geology and exploration information. The distribution of mesotherrnal shear zone gold deposits in the Reefton Goldfield, were examined against geological data-sets from both the regional (QMAP) and local prospect-scale mapping. Weights of evidence analysis generated a correlation matrix that highlights relationships and degrees of association that might otherwise not normally be recognised.   Mesothermal shear zone gold deposits have strong positive spatial correlations with Greenland Group host rocks and areas with moderate to high quartz vein densities; moderate-strong positive correlation with regions <500 m from folds, with regions <600 m from faults and five to eight kilometres from granite contacts; moderate correlations with Ntrending fault and fold segments; and no/weak/poor correlations with fault intersections, fold-fault intersections, bends in regional structures and magnetic and radiometric data. The regional and prospect scale data sets give different results, with the more detailed prospect scale mapping giving generally better correlations. This emphasises the value of detailed geological mapping in the exploration process.   Maps generated by prospectivity modelling consistently highlighted areas of known mineralisation and generate targets where follow-up investigation is warranted. The prospectivity per unit area provides a measurable value that should change as new information comes to hand and, in addition to highlighting targets, can be used to measure the impact of increased exploration expenditure and assess the effectiveness of exploration investment.

Jan 1, 2001