Search Documents

By Sinha DK

Coal Mining in India had been confined in the past primarily to two or three coalfields. Unscientific mining has led to huge degradation of land including massive subsidence of strata and disturbances of water tables to a wide extent. This has caused problems not only in flooding of mines from surface water but also in further planning of the surface drainage for current mining activities. Now, therefore, surface hydrology and land-use potentialities of the area have been endangered inflicting severe damage to the overall environment and ecology of the area. The paper Discusses certain investigative aspects of the problems highlighted as above in one of the coalfields, and encompasses mainly the following areas : 1) Quantitative estimation of the damage already done to the natural surface drainage system. For this purpose damage to topography and drainage for the last fifty years have been made out through the aerial photographs and topographic map sheets 2) Analysis and comparison of different states of such photographs are carried through to indicate the extent of damage to the hydrological conditions inducing undesirable changes in its land-use pattern. Based on the analysis, concrete suggestions are made to restore the water drainage system which will be most suitable for future mining in the area containing high grade coal. The design and planning of the drainage system is based on the total system approach including the cost benefit analysis as well as hydrological considerations.

Jan 1, 1988

By Bailey H. W

Power supply for remote mining developments is compared with supply to the general public with the conclusion that the private power plant operator has many opportunities to minimise his costs which are not open to public utilities. The main features of diesel, gas turbine and steam power plant and the limitation upon their application which may be imposed by the fuels available and the local conditions at remote sites are outlined. Reference is made to the value of joint examination by the mining engineer, metallurgist and power engineer to decide how to make best overall use of capital, labour and energy in co-ordinating the design of power and process plant and in setting no more than adequate standards of reliability and efficiency. Fluctuations in world markets make it difficult to plan mining operations to a firm time base. Suggestions are made to minimise the financial risk in forward expenditure upon power plant which in large sizes due to longer construction time may have to be ordered before a final decision is taken upon the mining development it is to serve.

Jan 1, 1973

By G Steward

Gravity Leaching of high-grade gravity gold concentrates, such as Knelson Concentrates, with the ACACIA Reactor represents a new generation of concentrate treatment methods. The ACACIA Reactor is a complete packaged plant for the maximising of gold recoveries from gravity gold concentrates. This paper will introduce the process technology and provide process results from the Porgera ACACIA Reactor installation. The advantages of the ACACIA Reactor are many, and justification for installation has been varied. The typical advantages of the process include: increased recovery of gold from the Knelson Concentrate; no return of high-grade table tails, often grading several thousand g/t, into the mill circuit; reduction in tails grades of slow leaching gold; reduction in the requirement for operating staff by the removal of the manual tabling process and replacing with a fully automated treatment system; improved security by removing the tabling step where operating staff come into direct contact with visible gold; improved health and safety, by the removal of the treatment steps for the table concentrate, which often include operators handling corrosive chemicals and the production of sulphur and arsenic compound fumes; and improved metallurgical accounting, by allowing daily head grade calculations. The ACACIA Reactor was developed by Anglogold for Union ReefÆs Gold Plant and has been in production for over two years, and has proven to be a low cost, high recovery, mechanically reliable method for the processing of gold concentrates. Such has been the success of the plant, there are now four full installations of the processing plant, including Anglogold Union ReefÆs, Anglogold Sunrise Dam, PACMIN Carosue Dam and Porgera Joint Venture.

Jan 1, 2002

The design, construction and operation of a 500,000 tonne per year Carbon-In-Pulp (C.I.P.) plant at Kambalda embracing the period from 1980 to 1982 has been previously discussed (Sceresini, 1982).Since that time the annual throughput rate has increased to 780,000 tpy.This paper discusses the changes and improve-ment made to allow this increased production to occur with minimal capital expenditure.

Jan 1, 1984

By L Alem

In the field of mineral extraction, complex technologies are being introduced in mines, operators/technicians rely on assistance from an expert (or more) in order to keep their machines functioning. Personnel with such expertise, however, are not always physically on-site. There is a growing need for innovative technological solutions to support effective delivery, just in time, of remote guidance between an offsite expert and an on-site maintenance operator. To meet this need, we have, as part of our Human System Integration project within the CSIRO’s Minerals Down Under (MDU), Transforming the Future Mine theme, explored the usefulness of a number of emerging technologies including: augmented reality, wearable systems and touch table interfaces. This paper presents ReMoTe, an augmented realty system for remote guiding using a touch table interface for the expert station and a combination of augmented reality and a wearable system at the operator end. In designing this system we were interested in exploring the extent to which it can increase the productivity and safety of maintenance personnel. This paper also presents Mobile ReMote, our recent development of a fully mobile remote guiding system. In Mobile ReMote, both the expert and the operator are using a near eye display and wearing a light computer in a back pack. The expert is able to guide the operator using his/her hands on the virtual display, while the operator is able to see the instructions on the rear eye display. Workers in the mining industry are highly mobile, a mobile expert and operator station will meet this need.

Nov 22, 2011

By Melcher G

The challenge to the zinc industry is shifting from maximum metal recoveries to the environmentally safe processing of the ore concentrates. The main source of solid residues from hydrometallurgical zinc processing is the iron content of the concentrates. Unfortunately iron precipitates from leach liquors contain various compounds which cause them to be considered as environmentally unsafe, unless they have been cleaned in subsequent process steps. This calls for separating the iron from hydrometallurgical processing as early as possible. For this purpose a process has been designed to eliminate the iron directly after neutral leaching the calcine. This is being done by direct smelting the neutral leach residue with a cyclone/top blowing unit. The zinc is recovered from the neutral leach residue as a metal oxide to be recycled to the zinc process. The iron is converted to a slag, which is resistant to atmospheric attack. Key data of the integrated hydro-/pyrometallurgical process are presented as derived from pilot plant tests by cyclone smelting and top blowing the slag.

Jan 1, 1993

By C Mark

Coal bursts involve the sudden, violent ejection of coal or rock into the mine workings. They are a particular hazard because they typically occur without warning. During the past two years, three US coal miners were killed in two coal bursts, following a six-year period during which there were zero burst fatalities.This paper puts the US experience in the context of worldwide research into coal bursts. It focuses on two major longwall mining coalfields that have struggled with bursts for decades. The Utah experience displays many of the ‘classic’ burst characteristics, including deep cover, strong roof and floor rock, and a direct association between bursts and mining activity. In Colorado, the longwalls of the North Fork Valley (NFV) also work at great depth, but their roof and floor strengths are moderate, and most bursts have occurred during entry development or in headgates, bleeders or other outbye locations. The NFV bursts also are more likely to be associated with geologic structures and large magnitude seismic events. The paper closes with a brief discussion of how US longwalls have managed the burst risk.CITATION:Mark, C, 2014. Coal bursts in the deep longwall mines of the United States, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 33–40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By E S. Bernard

Steel fibre reinforced shotcrete (SFRS) is increasingly being used as ground support in both civil and mining applications. In recent years, methods of assessing the performance of SFRS have been developed. These include the beam test such as that prescribed by ASTM C-1018 and the panel test prescribed in the EFNARC European Shotcreting Standard. The panel test has gained popularity in recent times due to the two-way action modelled in the test. However, some difficulties have been noticed. Shear failures sometimes occur and there appears to be a rather high degree of variability in the panel test results. A new method of testing panels has been proposed. A circular panel supported on three symmetrically arranged points has been assessed at the University of Western Sydney. This paper describes the new test which may be the basis of a new specification for the testing of toughness of SFRS and summarises research work which has been carried out to-date.

Jan 1, 1999

THE millng methods employed in the Mount Lyell Mining and Railway Company's mines are, perhaps, less known to the milling world than those of other important districts, due to the geographical remoteness and isolation of the Mount Lyell field,but they present many features which are unusual, and should be of interest to the mining engineer. Typical mining is carried out on an open-stope system, details of which are the result of local experience and evolution, and of which the outstanding feature is that the ground is so worked as to be largely self-supporting by virtue of domical form given to the stope roofs. It is locally termed "rill" stoping,' but differs widely from what is generally understood by that designation, chiefly in that the "rill" or slope is developed in every direction from a central focus, and not merely in directions followllig the strike of a lode or ore-body whose longitudinal dimensions are very much greater than its width. Such terms as "donie stoping" or "arched-back stoping" would be more appropriate and descriptive.The company's active operations' at the present time extend to the Mount Lyell and North Lyell mines, and, though the fundamental principles of stoping methods are the same in each, the dissimilarity of the ore-bodies, both in nature and mode ofoccurrence, necessitates considerable variation as to details to meet the respective conditions. The Mount Lyell pyritic body lends itself to the adoption of the .system in its simplest and almost ideal form, and a description of stoping in this mine willserve best to illustrate it, while later reference to details of practice in the North Lyell mine will indicate how it may be varied to meet more difficult circumstances.

Jan 1, 1915

MIM Holdings Limited (MIM) committed to a long-term future in copper in the Carpentaria Mineral Province in 1996 with the development of the Enterprise and Ernest Henry mines, and an upgrade of MIMsÆ copper smelter in Mount Isa, and copper refinery in Townsville. The upgrade of the copper smelter will enable the smelter to produce 250 000 tpa of copper with a single primary smelting unit, the copper Isasmelt furnace installed in 1992. The copper Isasmelt furnace currently smelts concentrate containing 145 000 tpa copper. To reduce the risk associated with the copper smelter upgrade, and shorten the ramp up time of the upgraded smelter, two high-rate trials were undertaken in 1997 to demonstrate that the copper Isasmelt furnace could, with an additional 525 tpd of tonnage oxygen, treat concentrates containing 250 000 tpa copper. During the trials the concentrate feed rate to the Isasmelt furnace was increased from its average rate of 100 tph of concentrate to 150 tph of concentrate. The increase in the capacity of the furnace was achieved by: supplementing the installed tonnage oxygen capacity of 595 tpd with an additional 300 tpd supply; reducing variability in the furnace feed rate from ¦25 per cent to less than ¦5 per cent; and reducing tramp air. The Isasmelt furnace smelted concentrate at a rate of 140 to 150 tph for four hours 25 minutes during Trial 1, and at a rate of 150 tph of concentrate for five hours and 30 minutes during Trial 2. The oxygen utilisation was 100 per cent during the trials with the process remaining under control. As a result of the development work for the trials the average treatment rate of the furnace under normal conditions increased by ten per cent.

Jan 1, 1998

By Fabjanczyk M. W

Artificial ground support has developed into a refined science over the past 20 years. From reactive support systems such as timber props and steel supports, to active systems such as roof bolts and cable anchors, ground support technology has now developed efficient systems that work well in many instances. However this paper demonstrates that there is still a long way to go to develop optimum ground support systems. Some conventional rock bolts and cable anchors emphasise their tensile capacity only, without considering other factors such as their shear strength or shear modulus, or if the support member can transfer all of its support capacity to the surrounding rock. Examples are given of the use of ground anchors with high tensile and shear capacity in underground coal mining as well as examples of slope failures in open pits where the cable bolts have remained intact because they have been unable to transfer their full capacity to the surrounding weak rock mass. For underground coal mines, speed of installation is also of primary concern, but it must also have high tensile and shear capacity both in terms of strength and stiffness. Ground support systems of the future must therefore address these problems. An innovative new rock bolt is discussed which goes some way towards solving these problems. This new rock bolt is screwed into the rock and thus has a direct mechanical interlock with the rock. Initial field results show that it has an extremely high anchor capacity and can be fully installed in approximately 30 seconds. It has considerable capacity to improve the productivity of the coal mining industry.

Jan 1, 1992

By W J. Bruckard, M J. Vaisey

Ashton Mining Ltd (Ashton) and Lynas Corporation Ltd (Lynas) have established a joint venture partnership to develop and process rare earth oxides (REOÆs) from the Mt Weld deposit in Western Australia. The deposit is located in a deeply weathered volcanic carbonatite structure that contains approximately two million tonnes of rare earth oxides at an average grade of 20 per cent REO. As part of the 1999/2000 feasibility study currently being undertaken by Ashton and Lynas, an extensive laboratory beneficiation test program was undertaken by CSIRO Minerals on diamond drill core samples from the Mt Weld orebody. The aim was to develop a flowsheet, based primarily on flotation that could be confirmed at pilot plant scale. The target concentrate grade was 52 per cent REO with a REO recovery of at least 35 per cent. Two main ore types, nominated as CZ (limonitic siltstone) and LI (nodular limonitic ironstone) were identified for separate laboratory evaluation. The lower grade LI-type ore overlies the higher grade and more extensive CZ-type ore. The majority of the work was conducted on the CZ ore; only limited testing of the LI ore was undertaken. The latter contains a clay component that will present difficulties in processing due to its poor filtering and settling characteristics. Two processing options for treatment of CZ ore were presented for pilot plant consideration. One (Option 1) includes gravity concentration prior to flotation while the other (Option 2) includes finer grinding and four stages of open circuit cleaning. The benefits of each scheme are discussed in detail. Neither has been fully optimised and the definitive flowsheet is most likely to be a hybrid of the two schemes, incorporating the best features of each. Typical metallurgical results from each scheme were final concentrate grades of 49 per cent REO, 10-16 per cent Fe2O3 and 3.2-4.8 per cent CaO. REO recoveries were above 35 per cent in both cases. Features of the processes developed by CSIRO were the inclusion of a gravity concentration stage prior to flotation, a modified flotation reagent scheme, a change in the method of feed preparation, and incorporation of magnetic separation to upgrade final flotation concentrates. Metallurgical results obtained from flotation tests on LI ore were much poorer than those obtained for CZ ore. The best rougher/scavenger result, with the limited amount of testing so far completed, was an REO grade of 32 per cent with a recovery of 28 per cent. Further work is needed to develop a viable processing route for this ore type.

Jan 1, 2000

By F Cappuccitti

A colourimetric technique, originally developed for methyl iso butyl carbinol (MIBC) based on the Komarowsky reaction, has been extended to a wide range of common mineral flotation frothers. The procedure, which is briefly described, is shown suited to on-site determinations in a campaign at Kennecott Utah Copper Copperton Concentrator (Rio Tinto). Some observations are described, including: frother (MIBC) concentration evolution down a bank, frother distribution between pulp and froth phases, and loss of frother over time due to adsorption on certain minerals. A possible interference with a fuel oil addition was overcome. MIBC in recycle water was also measured. The ability to monitor frother easily will help interpret gas dispersion behaviour and should permit further optimisation of flotation cell hydrodynamics and chemistry. The capability to directly measure should help optimise the type, amount and location of frother addition, and to assess frother recycled with reclaim process water.

Jan 1, 2005

The use of coal as a fuel for heat and power generation has a long history. During the nineteenth century most of the present combus- tion technologies were pioneered, as shown in Table 1, This period was associated with the "golden age" of coal and its contribution of almost 80% of the world's energy demands in the early,1900s . The decline in the use of coal has been due to the transfer of the heavy transportation area to diesel power, the elimination of coal as a household fuel and the substitution of oil for coal in power plants. Coal remains the major fuel for the electric utility industry and the present paper will be concerned primarily with that application. Table 1 outlines the development of coal tech- nology with the parallel understanding of coal as a material and its behaviour during combus- tion. Clearly many developments in combustion technology have occurred in this century, although most of the processes had been invented in the nineteenth century. Also, the great expanse in coal research of the past few decades has led to a greater understanding of the coal combustion process.

Jan 1, 1987

In order to do the discharge estimation better, it is valuable to find out appropriate formulas for estimating discharge in various pits, based on accumulating data, summarizing discharge patterns applying optimum seeking method and principle, by seeking redical exponent with help of the method of exhaustion, as well as testing and making statistics, in accordance with the quality standards established by our practical experience.

Jan 1, 1988

Structure is the most important control on the location of hematite deposits in the Hamersley Province in the Pilbara region of Western Australia. Unravelling the structural history of mineralised areas, however, is complex because the Province underwent three orogenic events, and three regional extension events followed the main episodes of compression. Steeply E to ENE dipping normal faults immediately predated deposition of the Beasley Quartzite of the lower Wyloo Group after the Ophthalmian Orogeny. Steeply NE and SW-S dipping normal faults predated deposition of the McGrath formation of the middle Wyloo Group, following the Panhandle Orogeny. The resulting interpreted rift was subsequently reactivated and tilted during the Capricorn Orogeny. Late NE trending normal faults are confined to the eastern half of the Province. High-grade hematite deposits occur in rocks that range from intensely folded (Mt Whaleback, Giles Mini) to rocks with less, or only little deformation (Paraburdoo, Channar), suggesting that folding had at best limited influence on ore genesis. In contrast, extensional normal faults are always associated with high-grade hematite deposits, and in particular faults that link the underlying dolomites of the Wittenoom Formation with the overlying iron formation, thus providing a pathway for mineralising alkaline fluids.

Jan 1, 2005

Territory Iron has seen fit to revive the old Frances Creek iron ore mine some 30 years after it ceased operations in AustraliaÆs Northern Territory. The key to this revival has been the changes that have happened since market forces, infrastructure limitations and a cyclone combined to force its closure. As it breathes life into this old mine, the Company is serious about its responsibilities to its shareholders, to its workers, to local and regional communities and to the environment. This paper addresses how Territory Iron has approached technical, operational and regulatory issues that apply in Australia. Some insight may be gained into the myriad of tasks that mining companies face to revitalise an old mine. These tasks vary from employing the latest exploration tools, best practice drilling, sampling and modelling of orebodies, optimisation of pit designs and schedules, maximising product value by blending, optimising infrastructure usage and minimising capital and operating costs. All of this has to take cognisance of commercial, environmental and other issues including Native Title.

Jan 1, 2007

By Kapoor M. L

EMF measurements were performed in the temperature range of 933-1095 K to determine the thermodynamic properties of oxygen dissolution in liquid lead and lead-tin alloys with tin in the dilute concentration range of 0 to 6 atom per cent. The oxygen in the Pb-O system was varied by equilibrating with (PbO) slag, and that in the Pb-O-Sn system was varied with the addition of lead oxide. Wagner's interaction parameter approach was used to evaluate the self interaction parameter and ternary interaction parameters at different temperatures, to yield: E8(pb) = 97.35 - 113.27 x 103/t Eo(pb) = 139 - 20.616 x104/1' Quasichemical formulation was employed to yield Inf to reveal the effect of tin on oxygen in lead. Results have been predicted on the basis of classical models and those obtained using the QCT approach of Alcock and Richardson at Z=2 have been found to agree with the experimental Data.

Jan 1, 1992

By Nyamekye GA, Subramanian S

Adsorption tests have been carried out to elucidate the interaction mechanism between dextrin and sulphide minerals. Sulphides such as galena and heazlewoodite exhibit high affinity adsorption over the pH range that coincides with the iep of lead and nickel hydroxides, and is suggestive of chemical interaction. The adsorption behaviour with respect to the sulphides of copper is of the low affinity type, and follows a different pattern. The adsorption studies on graphite, support the chemical interaction mechanism, with the metallic impurities serving as adsorption centres. In conformity with the proposed mechanism selective separation of galena from chalcopyrite and heazlewoodite from chalcocite has been Achieved.

Jan 1, 1993

By Mckenzie CK, Scott A

The injection of coal as an auxiliary fuel in ironmaking blast furnaces has been introduced on many furnaces worldwide. This paper examines the present practice of coal injection and discusses future directions for the technology. This has been undertaken through the use of a heat and mass balance model which predicts the replacement rates of coke by coal and the effect of coal injection on blast furnace productivity. The results indicate that future pulverised coal injection could replace substantial quantities of metallurgical coke, but that the energy balance economics of individual steel plants will have a dominating influence on the future of the technology.

Jan 1, 1987