Search Documents

By T J. Sheer

Water vapour refrigeration (systems using water as the refrigerant) could potentially be used to provide chilled water at underground locations in mines, as an alternative to conventional refrigerators using refrigerants such as R-134a. The use of water as both the primary and secondary refrigerants is attractive in concept since direct-contact heat exchangers could be used, yielding higher coefficients of performance. The disadvantage of water is the very high specific volume of the vapour at low pressures, which leads to great challenges in compressor design, as has been reported previously in the context of slurry-ice plants for mine applications (Ophir and Koren, 1999). Steam ejectors have long been known as alternative compression devices for refrigerators, but no work has been done previously on the possibility of using ejectors powered by high-pressure water, which is readily available in mines from long pipe columns in vertical shafts. This paper presents the results of a laboratory investigation into the use of high-pressure water as the motive fluid in an ejector refrigerator. No previously reported liquid ejector system has achieved subcooling of the process fluid, ie a reduction in fluid temperature within the evaporator to a level below that of the motive fluid. In contrast, the present work demonstrated that subcooling could occur at motive water pressures above 5 MPa. Mine cooling applications were considered and it was concluded that while this concept would not be feasible as a mine-wide cooling source, there could be specialised applications where it would be beneficial. One application would be to cool backfill and thereby reduce the heat load at the working face. In this case the best performance would be achieved by using the ejector in combination with an energy recovery system such as a Pelton turbine or a three-chamber pipe feeder.

Jan 1, 2005

By Deutsch G. P

The output of an underground mine often depends entirely on the mine winding system. -Decisions made--at the design stage affect the economy and operation'of the mine'.througb -its entire life. A modern mine winding installation is an integrated system and its design requires a multidisciplinary approach including expertise in the-materials handling, mining, mechanical, civil, structural, electrical and control engineering fields. The paper-sets out the elements of typical mine wind- ing systems-and describes some of the more important decisions which must be made during the planning and design process, It is no longer.adequate to. base the choice of a system on the pre- ferences and experiences of individuals. Major Australian winding install- ations are usually designed on the basis of overseas experience and some of the detail design is often carried, out overseas. Differences in basic design criteria occur from country to

Jan 1, 1973

Electronic Detonators have made significant strides over the last few years, both in quality of product and performance in different blast applications. The precision and flexibility of the SMARTDET units provides the mines with a powerful means of controlling blast results, giving both cost and productivity improvements. The SMARTDET Electronic Detonator System, robust and easy to use, has been successfully deployed over the last 18 months in improving mine productivity and creating safer working conditions in both quarrying and long-hole stoping. The key to the improvements has been the precision and flexibility of the electronic timing, and the ability of the mine personnel to grasp the concept quickly and use it effectively.

Jan 1, 1999

There are many factors influencing the way in which a mining company disposes of tailings. Some of the more important factors include physical and chemical properties of tailings, cost, availability of dam wall construction materials, type of mining operation, topography and environmental constraints. As a result, the mining industry has seen a diverse and innovative range of disposal methods developed to satisfy the many conditions imposed at tailings disposal sites. This paper discusses a range of tailings disposal methods currently practiced in the mining industries in North America. These methods include various inpit disposal techniques, upstream, downstream and centreline dam construction and zoned earthfill or rockfill embankment construction. The thickened tailings disposal method and the disposal of fine clays are discussed. The importance of improving the depositional properties of tailings to enhance storage capacity, water reclaim, dam wall stability and final reclamation is stressed. It is important that mining companies are made aware of the full range of disposal methods and dam construction techniques available today. Such an awareness will help improve the planning, design and construction of safer and more efficient tailings disposal facilities in the future.

Jan 1, 1989

By Komosa T

The increase in the proportion of sulphide ore treated by the gold mining industry has led to generally higher oxygen requirements. Additions of pure oxygen, hydrogen peroxide and in some cases calcium peroxide, have been proposed as a means of satisfying the oxygen demand and overcoming the problems from reactive sulphides in the ore. Current oxidant addition options and practice are reviewed.Laboratory oxygen demand tests are reported for a suite of ores to show some of the effects of pH and preaeration.Laboratory leach tests at high and low dissolved oxygen levels are reported on two of the ores with higher oxygen demands, and the results are assessed in terms of gold leaching kinetics, ultimate gold extraction, and cyanide requirements.

Jan 1, 1992

The production of synthetic crude oil requires a suitable coal or a coal extract modified by hydrogenation for pyrolysis. Existing classifications are broadly based on historical and current needs. One, Seyler's, is based on a visual display which can be used to present petrographic bounds. The analysis of the coal extracts from solvent hydrogen-donor testing allows an experimental limit to be described and a plant limit to be indicated. Australian black coals are discussed within these petrographic and plant bounds and their limitations as a feed for the production of synthetic crude presented. Potential uses for the aromatic liquid products are suggested. The application of the diagram as a screening procedure for sub-hydrous coals is described.

Jan 1, 1975

By R Herbert, M E. Malmstr÷, S U. Salmon

The study focuses on sulfide oxidation processes in unweathered pyrite-rich mine tailings from a soil-covered impoundment in northern Sweden. To simulate the oxygen-limited conditions in water saturated tailings two long-term column experiments were performed. Results are presented for the first 11 months of the experiments at room temperature. The tailings used in the experiments were of two different grain sizes (one coarse grained, in the range 0.02 - 0.6 mm with a grain surface area of 1.86 m2 g-1, and one fine-grained, in the range 0.0015 - 0.06 mm with a grain surface area of 10.00 m2 g-1) and with slightly different mineralogical composition. The S:Fe molar ratio in the leachates (1.0 - 1.5) indicates either that pyrrhotite is the main iron sulfide undergoing oxidation in our experiments, or, alternatively that the S:Fe molar ratio in the leachate is determined by pyrite weathering in conjunction with other processes releasing iron or immobilising sulfate. However, speciation modelling of the leachates indicates that ferrihydrite was close to saturation, suggesting that a ferric oxyhydroxide may have dissolved/ precipitated during the experimental period, thereby affecting the S:Fe molar ratio. Pyrite oxidation rates obtained from the two column experiments during æsteady-stateÆ were 2.25 + 10-13 and 8.45 + 10-14 mol m-2 s-1 in the coarse and fine tailings, respectively. Pyrrhotite oxidation rates, as an alternative, were 2.31 + 10-12 and 1.24 + 10-11 mol m-2 s-1 in the coarse and fine tailings, respectively. Natural microbial activity was confirmed in both the tailings and the leachates; therefore, the obtained oxidation rates are not strictly abiotic. It is thus concluded, based on the experimental results, that tailing heterogeneity will result in zones with different oxidation rates, related to their physical and chemical properties.

Jan 1, 2003

BHP BillitonÆs Yandi channel iron deposit has a large resource of approximately 1.3 billion tonnes. This is a bulk mining operation with a high degree of selectivity not being practical. In contrast the deposit geology is a complex interrelationship of primary channel facies, secondary enrichment of iron and a secondary redistribution of the major contaminants. These variations in geology and alteration can occur over ranges of hundreds of metres down to knife edge contacts. In addition, differences in primary facies and mobility during alteration often result in the iron and contaminants having different patterns of enrichment and depletion. Despite the scale of these operations, if the geological domaining is not optimal, significant errors in the resource estimate of grades and tonnage will occur. Getting the geology right has become a common clichT among mining professionals. However, in many situations, obtaining optimal geological domains for resource modelling is best achieved when there is input from geology, statistics and geostatistics. In this paper, moving window statistics are utilised to see through locally high variability to identify trends that assist in locating difficult to identify geological boundaries. After the creation of geological domains, univariate and multivariate statistics and principal component analysis assist in validating and characterising geological domains. Finally, variography and domain contact analysis are used to analyse the nature of the boundaries between geological domains. At the Yandi channel iron deposit, the inter-relationship between geological and geostatistical analysis has resulted in significant improvements to geological domaining and the treatment of domain boundaries during estimation of iron and contaminates.

Jan 1, 2005

By G D. Price

The Golden Blocks Goldfield is located in the Slaty Creek area,North West Nelson, about 20 km west of Collingwood. Alluvial gold was discovered in Slaty Creek in 1861. Gold was mined from quartz veins up to 1.5 m thick at nine mines from the 1890s until the closure of the Aorangi Mine in 1911. Total production from the Golden Blocks Goldfield is estimated at 46 000 ounces of gold. The Aorangi Mine was the largest mine, with a recorded production of 27 978 ounces of gold at an average grade of 36 g/t. Quartz veins containing gold and sparse sulphide mineralisation occur in a slightly metamorphosed, complexly deformed over-turned sequence of Lower Ordovician sandstones and shales. Primary gold mineralisation is associated with intensely deformed zones that occur near or at carbonaceous shale and sandstone contacts. Some eighty-five percent of all gold production (39 000 ounces) came from four mines confined to the stratigraphically lowest, most widespread shale unit. The quartz veins exhibit textures consistent with a hydraulic fracturing mode of vein formation with fissure infill vein types predominating over replacement textures. Stylolites of carbonaceous material and recrystallization features within the veins suggest multiple phases of deformation. The lack of wall rock alteration, and low primary fluid inclusion temperatures of 200¦ - 265¦ indicate that the ore fluids were associated with a low temperature epithermal system. A model consistent with similar mineralisation styles observed in Ordovician sediments from Pacific Rim occurrences is presented. The high grades (up to 100 g/t) mined from the upper levels of several mines suggests supergene enrichment processes associated with the Upper Cretaceous weathering surface. The Golden Blocks Goldfield has had no modern exploration. The most recent exploration was undertaken in the early 1980s. There are known acid intrusives in the area, with potential for the application of new models of intrusive-related gold mineralisation.

Jan 1, 2004

By Williams P. A

Tailings dams constructed by the upstream method have traditionally been built using the sand fraction of the tailings, which has automatically provided a relatively permeable embankment material, and helped provide the necessary drainage conditions which are a pre-requisite for safe and stable dam construction using this method. This paper discusses some recent trends which have resulted in proposals to use impermeable material in place of the sand fraction as the embankment material, both for the starter dam, and subsequent lifts. The consequences of these types of decisions on the overall stability of the dam are illustrated, and the need for continued monitoring of pore pressures in the tailings as the dam is raised is emphasised.

Jan 1, 1992

Copper heap leaching involves both the simultaneous and sequential leaching of very large tonnages of ore over long periods of time. It is not unusual to be leaching three or four million tonnes over periods of 12 to 18 months. As a consequenc

Jan 1, 1998

By Hedge AS

Mt Whaleback is one of the largest open-cut iron ore mines in the world. Haulage cost is the single largest component of operating costs at the mine. Past studies towards alternatives to truck haulage have recognised the potential viability of an in-pit crushing and conveying system, dependent on the proportion of uphill haulage. After seventeen years of mining Mt Whaleback still contains more than 1,000 million tonnes of ore, needing 1,800 million tonnes of waste removal to extract it. What was once a quarry has now turned into a large open pit. The increasing proportion of uphill haulage, the need to replace ageing 120 ton and 200 ton trucks and the necessity of achieving and maintaining a higher stripping ratio prompted, in 1984, the initiation of a new feasibility study into the viability of alternative material handling systems. A semi-mobile in-pit crushing and conveying system was found to be most suited to Mt Whaleback conditions. The East Pit was selected as the best location based on the analysis of haulage profiles measured on long term incremental mine plans. A capacity of 22 million tonnes per year was considered achievable by the proven technology currently available. A detailed estimation of capital and operating costs of two systems - one with trucks only and another with trucks, crusher and conveyor - for the removal of 22 million tonnes per year of waste rock, showed substantial cost savings achievable by the proposed system. An economic evaluation of the two systems established the advantages of constructing the in-pit crushing and conveying system. This is now under construction and will be commissioned in early 1987. Experience gained in constructing and operating this installation is expected to influence decisions on similar installations in future.

Jan 1, 1986

By Carras S, Kelsey P, Caccetta L

An important problem in open pit mine planning is that of detennining the optimum ultimate pit limits of the mine. These limits are that contour which is the result of extracting the volume of material which provides the total maximum profit while satisfying certain practical operational requirements such as safe wall slopes. The determination of the optimum pit contour provides information that is essential in the evaluation of the economic potential of the mineral deposit. A number of optimisation techniques are available for determining this contour with the Lerchs-Grossman and the Network Flow methods being the most favoured. Unfortunately, direct application of these techniques to large ore-bodies may cause considerable difficulties because of the computational time and storage requirements. In this paper, we present a strategy for resolving these problems, and the associated pit design software PITOPTIM (incorporating a fast network flow technique) and a data reducer, BOUND. The results presented highlight the speed and power of the software package rivalling the popular Lerchs-Grossman technique. An application of the software for a sensitivity analysis is also presented and discussed.

Jan 1, 1991

The Yabulu refinery of Queensland Nickel Pty Lld near Townsville now imports more than three million wet tonnes per year of nickel laterite ore from New Caledonia and Indonesia, making it the largest importer of any commodity in Australia. The project has illustrated that importing untreated bulk ore and re-exporting high value products makes good economic sense for the company and the nation.The economics of this exercise were considerably enhanced in 1994 by changing the project's principal product from nickel-oxide sinter to refined high-purity nickel metal. It is one of the few operations in the world where nickel ore is transformed to nickel metal at a single site.Several novel technological processes were developed at Yabulu and incorporated into the refinery to allow this product transition to occur. By utilising internally developed technology the new processes were installed at a capital cost of less than $10 million. It is unique for a large nickel producer to change completely the quality of its entire product range many years after the plant was constructed and considerable attention to marketing the new products has been required.The changes have meant that the project is no longer limited to selling lower-value oxide sinter to a relatively small number of large stainless steel mills. In the past year sales of the new high purity nickel metal products have expanded to include a broad range of international customers in the special alloy, foundry and chemical industries.

Jan 1, 1995

The epizonal Ag-Pb-Zn vein deposit at San Bartolome is characterised by a base-metal sulphide assemblage containing the spectacular development of interpenetrating, bladed networks of pyrrhotite which have been replaced by marcasite and pyrite. A similar assemblage displaying the same crystal habits and textures are also a diagnostic feature of the Sn and Sn- Ag deposits of Bolivia. On this basis, it is reasonable to conclude that both deposits were formed from fluids of similar nature and origin. Although no economic accumulation of Sn is known in San Bartolomr, further comparison of the geologic setting, age, mineralogy, fluid inclusion data and magmatic association of this deposit with the Bolivian systems has highlighted additional similarities consistent with a hypothesis that more extensive Sn mineralisation might exist in the San Bartolomd area.

Jan 1, 1995

Commissioning is one of the many phases of a project, it has inter-dependencies with the other phases, as they have amongst themselves, and has its own terminology and distinctive features. Commissioning time and cost can severely affect project economics, especially through unrealistic estimating, and requires a separate management team to ensure full control is. maintained. Targets to be achieved in commissioning are identified, together with the necessary policies to achieve them. Factors which have to be taken into account in applying these policies are Discussed.

Jan 1, 1986

The Henty Gold Mine is a good example of a situation where conditional simulation and optimisation techniques may have useful impact on modelling of mineralisation distribution and ore definition. Much of the gold mineralisation at Henty is concentrated within an alteration zone which is both physically discontinuous and forms only a small fraction of the overall mineralised volume. The alteration units are mappable from diamond drill core and underground workings. Conditional simulation and optimisation techniques for ore definition have found considerable success in the open pit gold mining environment. For many reasons including computational efficiency, lack of consistent geological information, and lack of familiarity with ideas and methods among mine geologists, implementations of these methods in open pit mining have been comparatively simplistic. Modelling is commonly reduced to treating the sample data as a single geologic population. This paper discusses the application of the MP method (a particular implementation of conditional simulation and optimisation) to modelling the distribution of potential ore blocks in the Henty gold mineralisation. The approach allows the mine geologist to model both the spatial geometry of the alteration types and the gold grades associated with each alteration type in a single process. Options allow the geologist to include or exclude underground geological mapping and face sampling depending mainly on the abundance of drill hole sampling and the quality of the face sampling. An optimisation algorithm based on maximisation of profit from mining is used to assist in ore definition.

Jan 1, 2000

By Shrivastava P

The iron orebodies of the Pilbara region are formed by supergene enrichment of banded iron formation and rarely do such processes produce orebodies with uniform grade distrib- utions. The orebodies being mined or developed have to be worked to grade/quality constraints imposed by contractual agreement rather than natural characteristics. Hence it is imperative to use a non-biased ore reserve calculation method. The geostatistical study of a typical iron orebody is presented. Emphasised are the geological characteristics of the orebody manifested as a variable grade distribution of iron and impurities; the determination of variogram model; subsequent uses of the model for computation of ore reserves and kriged lock estimates; computation of dispersion variance and conditional simulation of orebody.

Jan 1, 1977

By L Alem

In the field of mineral extraction, complex technologies are being introduced in mines, operators/technicians rely on assistance from an expert (or more) in order to keep their machines functioning. Personnel with such expertise, however, are not always physically on-site. There is a growing need for innovative technological solutions to support effective delivery, just in time, of remote guidance between an offsite expert and an on-site maintenance operator. To meet this need, we have, as part of our Human System Integration project within the CSIRO’s Minerals Down Under (MDU), Transforming the Future Mine theme, explored the usefulness of a number of emerging technologies including: augmented reality, wearable systems and touch table interfaces. This paper presents ReMoTe, an augmented realty system for remote guiding using a touch table interface for the expert station and a combination of augmented reality and a wearable system at the operator end. In designing this system we were interested in exploring the extent to which it can increase the productivity and safety of maintenance personnel. This paper also presents Mobile ReMote, our recent development of a fully mobile remote guiding system. In Mobile ReMote, both the expert and the operator are using a near eye display and wearing a light computer in a back pack. The expert is able to guide the operator using his/her hands on the virtual display, while the operator is able to see the instructions on the rear eye display. Workers in the mining industry are highly mobile, a mobile expert and operator station will meet this need.

Nov 22, 2011

In the last two decades, equipment used in the coal mining operations has become much more sophisticated. The way that work is organised and performed in the industry has also changed significantly. Changes in equipment specification or procedures inevitably means that the risk associated with that equipment or procedure also changes. In an attempt to address this the Joint Coal Board Occupational Health and Safety Trust (JCB) commissioned the University of New South Wales Mining Research Centre and Mine Site Technologies to perform a feasibility study into the development and deployment of Virtual Reality (VR) based training simulators in the New South Wales coal industry. The main aims of the study were to identify, the key providers of VR Technology, the VR options available to the JCB and the information that would need to be included in any simulator. It was anticipated that a critical assessment of these components would produce a format for a cost effective, state of the art simulator that could be readily accessed by all mines. The expectations of the feasibility study were that VR should offer three-dimensional (3D) simulations that are interactive, high-resolution models of real environments based on best practice Safety Management Plans. It was anticipated that the simulations would allow trainees to experience the consequences of poor decision-making and allow them to learn from their mistakes in a safe and forgiving environment. It was envisaged that such simulators would become an addition to the existing training methods used in the industry.

Jan 1, 2003