Search Documents

By Newman H. A

Goldsworthy Mining Limited is currently mining iron ore at an annual rate of 7 million tons from several small orebodies, each of which exhibit wide variations in iron, phosphorus, silica and alumina contents. Each orebody is mined at its average ore reserve grade and therefore mine planning and grade control techniques have had to be tailored to achieve a constant production blend.

Jan 1, 1973

Effective pre-splitting is a key feature of wall control blasting. Most mining operations use historical designs or rules-of-thumb for designing pre-split blasts. If productivity and safety benefits are to be gained, these methods need to be improved in order to accurately predict pre-split performance. This will become more pertinent as overburden depths increase, placing more demands on the pre-split operation. A classical qualitative quasi-static description of pre-splitting (Kutter and Fairhurst, 1968) is presented and it is shown to give some useful insights into the pre-splitting process. In particular, it is clear that the time interval between the initiation of adjacent pre-split holes is a very important factor. In terms of this analysis, it is shown that current techniques which employ detonating cord as the surface initiation system are not optimal. A static quantitative model for pre-split design which has been widely reported is then discussed and its simplifying assumptions and their implications are examined. It is shown that several of the assumptions may be reasonably justified in the light of real pre-split results. It is concluded that the model should yield conservative designs. For this model, the key calculation of the blasthole pressure that is needed to determine the required explosive charge is highlighted. Popular methods employed in the literature for describing the expansion of real detonation products are shown to be inappropriate and an alternative method using the non-ideal detonation code, CPeX, is proposed.

Jan 1, 1995

By Yambu J, Titus K

Geotechnical investictations and monitoring have been integral to development of the Porgera Gold Mine. The steep, unstable terrain has required a program for monitoring of slopes and foundations which includes survey stations, borehole inclinometers and piezometers. Case studies of the Maip Pass landslide, Yakatabari land-slide, Anawe Plant Site CIP pond excavation and batter, and a load test study for mine waste dumps are presented.Monitoring is needed to ensure that geotechnical risk is kept to a minimum. A vigilant program will be required for the life of the mine.

Jan 1, 1994

By Kaleta S, McTavish LP, Turner RD

Primary production blasting at Hamers- ley Iron began with seven inch holes at Tom Price in 1966 and has developed since then to large multiple row shots of 381 mm holes at Tom Price and 311 mm at Paraburdoo. Up to 1.3 million tonnes are initiated in a single blast with the average around 300,000 tonnes. Development can be traced through Anfo, AlAnfo, slurries, various boosters, initiation and delay techniques, hole loading and daily operating practices. A standard practice could be developed for the two mines for normal pro- duction blasts; this would not apply to such common variations as low "paddy" shots, pre- splitting, tight corners necessitating single row drilling etc. Because of ground variation three or even four sizes of drill holes may well be economic- al for blasting, even though this would be off set by complications in operation, supervision, store stocking and maintenance, particularly in Drilling.

Jan 1, 1978

By P Alspach, R Buxton, C Morgan, C Ross

Mining companies worldwide have an increasing interest in restoring indigenous ecosystems following mining. Low levels of plant nutrients and organic matter, pH extremes, heavy metals, physically challenging media, and difficult climatic conditions all hinder revegetation of steep rockdump slopes. Our techniques use colonising pioneer plants to accelerate natural soil development and plant succession processes on minesites that are difficult to revegetate with locally sourced plants by traditional techniques. Suitable treatments and pioneer species must first be identified for each rocktype. Field trials at the Stockton Coal Mine in Buller have shown that successful acceleration of moss and pioneer plant establishment is possible. Best plots showed a mean of 15 per cent moss cover and 3.3 per cent vascular cover after 12 months compared with 0.1 per cent and nil respectively for controls. Techniques have been extended to field-scale trials, using hydroseeders and dryblowers. These techniques show potential for practical land rehabilitation, whilst conserving local biodiversity.

Jan 1, 2003

By Saint-Smith J. C

The anode, tank house and wire bar plant and operations are described with particular reference to those features of design and methods which are characteristic of this refinery at its inception.Reference is also made to auxiliary equipment, transport and materials handling facilities.The work of commissioning the plant late in 1959 is discussed and comment is made on the organisation of construction and origin of the equipment.LOCATION OF PLANTThe site chosen for the copper refinery is on level ground adjacent to the junction of the Mount Isa and the main north-south railway lines at Stuart near Townsville, Queensland. Blister for refining is received by rail from Mount Isa. Refined products are taken 10 miles by road to Townsville Harbour for shipment to other Australian ports or overseas, or despatched by rail direct from the plant.Adequate room for expansion was provided to cover copper refining and any associated industry. The layout of future extensions was planned and space reserved for them before detailing the original units of the main refinery.The initial plant also provides convenient storage facilities and is laid out to derive the greatest benefit from prevailing northerly breezes during the humid tropical summer.As far as possible, the working areas are located so that the prevailing winds cool them as they traverse the buildings.These factors are of very great importance since this is believed to be the only copper refinery in the tropics operating with all white labour and in any case the Company set out to provide the best possible conditions for its operating personnel.

Jan 1, 1961

By Ham G. I, Just G. D

The model considers a range of design parameters and operating condit- ions and evaluates the significance of these in the ultimate design of a mine. It also considers organizational features associated with the mining method and examines the inter-dependence between operations. An important characteristic of the model is the use of both stochastic and deterministic methods to study the behaviour of the complete mining system. The simulator selects the appropriate unit operation, computes and records its time, performs it and then calculates the production and cost data. Output is in the form of shift, day, week or period repor-ts. These reports will indicate problem areas such as restrictions in the production network for a given set of conditions. The likely effects of alternative means of solving these problems can be evaluated by changing the original input. Such information could be used by the mine management to select an

Jan 1, 1974

The current quantity of rejects from coal beneficiation in Australia represents 20 to 25% of raw black coal production. Approximately 80% of the rejects are derived from coarse processing for particles in the 200mm to 0.5mm size range. The safe and enviornmentally acceptable storage of coarse coal rejects is of interest to coal mining companies. Additional public benefit would be derived from the utilisation of a waste product as a source of fill material for civil and mining engineering applications. BHP Engineering has taken a leading role in the design for storage and utilisation of coarse rejects from two mines associated with the Broken Hill Proprietary Conipany Ltd. The tailings dam at Stockton Borehole Colliery (N.S.W.) is to be raised and a study by BHP Engineering has shown that coarse rejects are suitable for the formation of the supporting embankment surrounding a compacted clay core. Transportation and storage of coarse rejects at the Thiess Dampier Mitsui Riverside Mine (Moranbah, Qld) is achieved by a conveyor leading directly from the coal preparation plant to a discharge stacker on the crest of the rejects stockpile. Production of coarse rejects was higher than anticipated for the initial dump design. BHP Engineering has completed a review of dump design with emphasis on safe operating conditions for the conveyors and stacker system. Data on the geotechnical properties of coarse rejects from Australian coal mines are presented. Coarse coal rejects are a material which should not be considered as waste, but as a potentially valuable resource for many future applications. Appropriate engineering design for the storage and utilisation of coarse rejects would result in an improved environment and economic benefits for the Community.

Jan 1, 1987

With the recent wider introduction of friction hoists of the Koepe type. for winding from depths of more than 3000 feet it has been found that failure by fatigue is the most common form of rope deterioration. Large numbers of wire breaks occur near the centre of the rope cross-section and it is difficult to detect these with certainty using the preferred d.c. magnetic test. For best results with conventional search coils their dimen- sions should be related to the typical wire break field pattern surrounding the longitudionally magnetised rope. The field of a broken wire was experimentally determined, using a Polish type MD6 Defectograph wire rope testing magnet and a short prepared length of rope with a movable simulated broken wire. The external field distortion perpendicular to the rope was measured by means of a gaussmeter and Hall probe. The advantages of this method are that terrestial magnetism and inherent rope "noise" have no effect on the results.

Jan 1, 1971

By M D. Melville, B C. T Macdonald, T D. W

The surface waters in regions with acid sulfate soils (ASS) can contain high concentrations of acidity and dissolved metals. These soils cause problems for agriculture, construction and development. The water can be neutralised through many techniques, however a technique that is low in maintenance and low in cost is most desirable. Due to the vast spread of ASS along AustraliaÆs coastline an expensive and high maintenance solution would not be cost-effective. In this study, a passive treatment system that has been used to neutralise acid rock drainage has been applied to treat ASS water. This system is commonly referred to as an oxic limestone drain (OLD) or an anoxic limestone drain (ALD) depending on the waters dissolved oxygen concentration. The system that has been developed for ASS has a similar closed system to the OLD or ALD, that traps the carbon dioxide which forms when limestone reacts with acidic water. It has been called a closed tank reactor (CTR) and is constructed by placing limestone into an airtight tank. A common problem that will occur when acidic water with a high concentration of dissolved metals reacts with limestone is the formation of metal oxy-hydroxide precipitates. These precipitates can coat or armour the limestone and reduce its reactivity. To minimise the accumulation of precipitates in the CTR, perforated subdrains have been installed. It is anticipated that high water pressure and flow through the subdrains will remove some precipitates. A sump has also been installed at the base of the tank to collect precipitates that settle under gravity. The CTR has been tested for 70 days at a sugar cane farm located at McLeods Creek, NSW. Within this time the sump and subdrains have been used to flush the system. An orange solution was produced during flushing and it is believed to contain iron and aluminium precipitates. The initial performance of the CTR raised pH by at least one unit. Almost all dissolved aluminium was removed and more than half the dissolved iron. The total titratable acidity ranged from 17 - 92 mg/L CaCO3 in the initial month of monitoring. After passing through the CTR the acidity was reduced to zero. The performance of the CTR during the last few days of monitoring decreased. This is believed to be due to a pulse of water with higher acidity and dissolved metal content that lasted a week. In this pulse, the acidity reached 307 mg/L CaCO3 and the total dissolved aluminium reached a maximum of 24 mg/L. Higher concentrations of dissolved metals may have been the cause for lower performance due to increased precipitation and coating on the limestone.

Jan 1, 2003

By Gee C. E

Ore reserves at the Kambalda Nickel Operations of Western Mining Corporation are estimated using the polygonal method for calculating areas of influence of drillholes. All raw assay and survey data are stored on one disk pack on the Company's CYBER 73 computer located in Perth, about 600 km from Kambalda. The initial step involving the computer is to search all assay data and calculate all potential ore-grade intersections. As the orebodies are thin, structurally complex and many are in close stratigraphic proximity, the selection of intersections which have the best grade over at least a minimum mining width involves complex logic. The orientation of an ore surface at each drill intersection point and a zone code are added to each intersection by the geologist from geological plans prepared for each ore surface. The orientation data together with downhole surveys enables the calculation of inter- section true widths and the zone code links each recalculated intersection to the appropriate ore surface.

Jan 1, 1977

By R Dimitrakopoulos

The development of mineral resources is based on a spatial model of the orebody that is only partly known from exploration drilling and associated geological interpretations. As a result, orebody models generated from the available information are uncertain and may require the use of stochastic conditional simulation techniques. Multiple-point methods have been developed for petroleum reservoir modelling, enabling reproduction of complex geological geometries. This paper considers a multiple-point approach to capture the uncertainty of the lithological model. The implementation of the method at the Yandi channel iron ore deposit in Western Australia and performance characteristics are discussed. The uncertain lithological model translates into considerable grade-tonnage uncertainty.

Jan 1, 2007

In this year marking the centennial of the Geological survey of Western Australia, it is appropriate that we should review the value of the contribution of the Survey, and Australian Geological Surveys in general, to the exploration industry. Most geological surveys in Europe and North America had their origins in the first half of the 19th Century when the burgeoning Industrial Revolution was demanding the identification of new sources of coal and iron ore. Australia, as a young nation, essentially dependent on an agricultural and pastoral industry, and with already discovered vast coal resources in Eastern Australia, had, no great need to explore for new mineral resources. However, with the discovery of gold in 1851, the mineral potential of the country became apparent to the whole world and the first Geological Survey in Australia was set up in 1852 in Victoria under A.R.C. Selwyn. After a number of false starts all Australian States had an established Geological Survey by 1900. It is hard to assess the contemporary value of the early work of the Geological Surveys with respect to exploration, almost all major mineral discoveries were made by prospectors and most mining companies had little time for geologists - although the Chamber of Mines in Western Australia in 1910, did recommend that the Geological survey be granted an additional ten thousand pounds over two years to map all existing goldfields and the country between them, and produce a reconnaissance map of the area east of a line between Wiluna and Edjudina as far as the South Australian border!

Jan 1, 1988

By Haigh C. J

A process has been developed to recover at least 75% of the 2-naphthol contained in cobalt precipitate produced during the removal of cobalt from electrolytic zinc plant solution. The recovered material is in a form suitable for recycling to precipitate further cobalt from solution. The process consists essentially of two steps. The first involves leaching of cobalt precipitate in 400 g/l sodium hydroxide solution at 95¦C in the presence of an additive. The second step involves treating the filtrate from the leaching stage with sodium sulphide to precipitate cobalt as the sulphide thereby re- generating the sodium hydroxide for recycling. The process is only marginally profitable at present 2-naphthol prices, giving a net return of 20% on a capital investment of $1 200 000. A reaction mechanism is proposed which accounts for the 25% loss of the 2-naphthol in the recovery process.

Jan 1, 1977

By C Samuelsson, Q Shu, A Lennartsson, F Gyakwaa, A Andersson, J Isaksson

The physico-chemical property, viscosity, is essential for pyrometallurgical processes and influences the settling rate of valuable metal droplets in slag, affecting the metal recovery. The copper slag from smelting furnaces typically contains between 1 and 2 wt per cent Cu, which equals to or is higher than in most sulfidic copper ores mined today, meaning the slag is a valuable resource for copper extraction. A low viscosity is desirable for slag-cleaning through a settling furnace where entrained droplets settle under gravity. One approach to control the viscosity is through the slag composition. The literature has limited data on the correlation between viscosity, slag structure, and optical basicity of iron silicate slag with FeO/SiO2, CaO, and Al2O3 as factors. Therefore, the present study evaluated the influence of these factors on viscosity and correlations with slag structure and optical basicity. The FeO/SiO2 ratio (at%/at%) and the CaO and Al2O3 content were altered in two levels, resulting in a two-level full factorial design with three factors. The study was done by synthesising FeO–SiO2–Al2O3–CaO–MgO–Cr2O3 melts, followed by water granulation. The melt structure of the samples was analysed with the help of Raman Spectroscopy. The viscosity was then estimated with a high-temperature rheometer using a Mo spindle and crucible. The results showed a correlation between the optical basicity, FeO/SiO2 ratio, and viscosity, where a high optical basicity and FeO/SiO2 ratio were beneficial for achieving a low melt viscosity.

Jun 19, 2024

By Olofsson O, Durance M-V, Villeneuve J

Modelling of the Sala Agitated Mill (SAM) using a simplified solution to the population balance approach has been carried out. The rate of breakage is modified by the mill power, providing predictions of the resulting product size distribution for different grinding conditions and mill sizes. The power of the mill is estimated by a physically derived function, using an assumption that the mill power consumption mainly arises from the ball to ball friction within the mill. The grinding efficiency, depending on the media ball size and pulp density is approximated in the model. Experimental work on grinding a complex sulphide ore using a pilot scale SAM 7.5 has been carried out. Good agreement has been found between the data from the test campaign and the simulated values. The model has also been validated with experimental data from a pilot grinding of calcium carbonate and from an industrial mill. The model is included in the USIM PAC simulation software.

Jan 1, 1995

This report chronicles the historical development of longwall mining in the United States and speculates on future developments to the turn of the century. Five eras of technological development during the modern period are described and analyzed. These eras discuss the development of (1) mechanized extraction, (2) self advancing roof supports, (3) high capacity roof supports, (4) shield supports, and (5) system automation. Current trends are analyzed in terms of: longwall utilization, production capability, support capacity, face widths, and new technological developments. From these analyses, the future of longwall mining to the year 2000 is speculated. It is concluded that longwall mining will continue to grow in importance during the next decade and that the next major technological milestone will be the realization of a fully automated longwall mining system.

Jan 1, 1992

To obtain the best economic results in treating the comparatively high-grade ore of the Kalgurli Mine a good roast is essential, and the effort of this paper will be to briefly describe the plant and the conditions prevailing in roasting, which, on an output of about 360 tons daily, subsequently enable an average extraction of slightly over 94% of the gold to be maintained.The percentage of sulphur in the ore varies between 2'5 and 3'5, the lower figure existing when treating oxidized ore. The average gold value is 13 dwt; this occurs chiefly as sylvanite, containing .a lower percentage of silver than is usually present in that mineral. One ore body in the mine contains hessite (Ag2Te) in considerable quantity, associated with gold telluride, and when ore from this stope is being treated the silver contents rise to as high as 20 dwt, but the usual amount is about 9 dwt. per ton, of which only a small proportion is extracted. Other metallic minerals, in addition to pyrite, occurring more or less commonly, are arsenopyrite, magnetite, chalcopyrite, and the tellurides calaverite (AuTez)and coloradoite HgzTe3). A small proportion only of the value occurs as free gold.

Jan 1, 1911

By C Standing, R Lacourt Rodrigues, C Q

The value of iron ore depends on the grade of the contaminants. Scheduled iron, and the associated contaminants, provides mine planners with a measure of stockpile feed and blending requirements. Blending at the stockpiles is one approach to optimising iron grade, while minimising the variability of contaminant grades. These schedules are typically based on resource models incorporating geology and iron and contaminant grades. Resource models reflect best estimates of trends for each of the elements rather than the potential variability, which is critical for accurate short-term blending. Conditional simulation provides a tool to describe the likely variability of each element. Only recently has conditional simulation technology allowed the inherent correlation between elements to be incorporated into the process. This paper presents the stepwise co-simulation process used to simulate and describe multi-element variability for effective mine planning. A case study using the multi-element conditional simulation and the subsequent uncertainty in the schedule and stockpile planning is presented. This process supports proactive mine planning to minimise unexpected fluctuations in the final product.

Jan 1, 2005

pNumerical modelling has been used to examine the relationship between the results of two commonly used methods of assessing the propensity of coal to spontaneous combustion, the R70 and Relative Ignition Temperature tests, and the likely behaviour in situ. The criticality of various parameters has been examined and a method of utilising critical self-heating parameters has been developed. This study shows that on their own, the laboratory test results do not provide a reliable guide to in situ behaviour but can be used in combination to considerably increase the ability to predict spontaneous combustion behaviour./p

Jan 1, 2005