Search Documents

By R Morrison, P Walters, B Adair, V Jokovic

‘Grade Engineering<sub>®</sub> is an integrated approach to coarse rejection that matches a suite of separation technologies to ore specific characteristics and compares the net value of rejecting low value components in current feed streams to existing mine plans as part of a system-view’ (Walters, 2017). Two of these technologies are directly recoverable through screening stages: Natural Deportment and Induced Deportment. The potential for taking advantage of “Natural Deportment” by size following blasting and crushing has been demonstrated for a range of ore types. Simple and low cost screening can in some cases generate a fine product with improved grade and a lower grade oversize which can be directed to leach or to waste. Where an ore body consists of many different ore types, the traditional approach of blending to metal grade will often add to complexity of treatment, which will reduce the effect of “natural deportment” by size.CITATION: Jokovic, V, Walters, P, Adair, B and Morrison, R, 2018. Applying enhanced grade engineering to complex ore bodies, in Proceedings Complex Orebodies Conference 2018, pp 21–23 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By Hayes J. A

The satisfactory ventilation of an extensive coal mine is a subject which requires continual attention from all concerned.It must be remembered that a colliery contains many miles of workings, extending in all directions and throughout which noxious gases may be given off either naturally or by oxidation of the coal; fumes from explosives will be produced, dust will be gathered and carried in suspension, and water will be evaporated, producing a high humidity. Hence a considerable quantity of air in movement must be available to provide sufficient oxygen for men and horses, as well as to dilute and sweep away impurities, and maintain a tolerable degree of coolness.To maintain these conditions a modern colliery is divided up from the main ventilation shafts or adits (as the case may be) into a system of main airways, and in the working districts is further subdivided into district splits. To initiate the air movement, large centrifugal fans with a displacement capacity of up to 400,000 cu. ft. of air per minute are installed, generally in drifts off the upcast shaft, or adit, and at the return end of the ventilating circuit. These fans are thus exhausting fans and by producing a region of low density bring the heavier air at the other extremity of the circuit into movement to correct the difference in density, so far as it is not prevented by the frictional resistance of the airways. A flow of air is thus established, and it is obvious that to enable this volume of air to be as great as possible, the frictional resistance of the mine airways should be maintained at the lowest practicable figure. To this end, main airways should be as large as possible, have sides as smooth as practicable, and be straight, any necessary bends being of large radius.REQUIREMENTS OF THE VENTILATION SYSTEMThe New South Wales Coal Mines Regulation Act contains stringent provisions on requirements of the ventilation system. The main points are expressed in the following extracts:"In every mine which is in operation, unless a certificate of exemption from compliance with this rule has been granted by the Minister, whether any person employed therein shall be...

Jan 1, 1947

Gentlemen, you heard the good Doctor has commissioned me to make a'summary of the proceedings to date and also to close the said proceedings. It seems that over the years the business of making a summary alternates between'Mr. Pearce and myself, also I,think that w~oever is around onthe day in question 'obtains the task and apparently I drew it this, year. It is hoped you will be patient as previous experience in this capacity'indicates that the best way to proceed is to have a brief summary on each paper and then do a summary of summa~ies. This makes the approacha little cumbersome but it is felt to be fair to each author and it brings'back to the audience some recollections of what transpired at the time and they can make their own decisions, which may not necessarily agree with those of the 'sum'marisor.

Jan 1, 1983

By Harper B

The mining industry has developed a comprehensive view of the need to have production personnel well trained in the use and maintenance of mining equipment. A strong commitment from the industry to this view has been instrumental in creating an efficient, profitable and productive industry based on modem production processes, sophisticated equipment and a multi skilled workforce. As the industry continues to develop, and the skills and knowledge needed by productive workers continues to expand, the training processes adopted by the industry will need to develop in parallel, not only making use of the latest advances in learning theories, instructional design and technology, but also using these knew ideas in more efficient ways.

Jan 1, 1998

By Niemann G

The paper addresses certain mining provisions of the Aboriginal Land Rights (Northern Territory) Act 1976 and the development of Mining agreements negotiated pursuant to Section 43 of the Act. Difficulties for miners and Land Councils alike arising out of the operation of the Land Rights Act will be discussed. Possible scenarios for the resolution of these difficulties will be proposed.

Jan 1, 1984

By A Baensch, E Grimsley

Eloise Copper Mine is situated 56 km east-southeast of Cloncurry, Queensland, Australia. The deposit was discovered by BHP Minerals in 1986 during follow up diamond drilling of EM anomalies associated with major aeromagnetic anomalies. The deposit is overlain by 60 m of Mesozoic cover. Amalg Resources NL commenced mining during 1995 by means of decline access and long hole-stoping. The total mineral resource comprised 1.77 million tonnes at 4.10 per cent Cu as at the end of June 2003. Proved and probable reserves are 930 000 tonnes at 3.97 per cent Cu. Mineralisation is hosted within a strongly foliated Proterozoic meta-sedimentary sequence comprising arenites and schists. The metasediment sequence also contains a coarse-grained amphibolite body possibly representing an early intrusion of gabbroic composition. Economic mineralisation characteristically occurs as a number of steeply plunging lenticular bodies with strike lengths of between 100 and 200 m and maximum widths approaching 25 m. The principal orebody, the Levuka (B) Lode, displays a down plunge extension exceeding 1000 m and is open at depth. Ore mineralogy is almost exclusively chalcopyrite with the principal gangue phases consisting of pyrrhotite + quartz + carbonate. A biotite + hornblende + magnetite assemblage represents locally intense mafic alteration of the metasedimentary host sequence. Magnetite is present in variable amounts and may be locally significant in some of the smaller satellite orebodies. Within the orebodies the sulfides display a range of textures from massive through to vein like. Sulfides commonly display brecciated textures at a range of scales. Post-mineralisation faulting has severely dislocated the orebodies, resulting in a complex arrangement of fault bounded ore blocks. These faults display considerable variability in regard to strike, dip and amount and direction of throw. A recent review of the fault system by means of large-scale structure underground mapping, re-interpretation of drill core and 3D modelling has led to a significant improvement in the understanding of these structures. A significant upgrade of the geological database has accompanied the structural review. The overall improved understanding has aided the mine design processes with particular regard to decline and access development and pillar location. This has also impacted on the design of drilling programs and exploration for additional satellite ore zones.

Jan 1, 2003

By Zamora C

The performance of a system for detecting the onset of overloads on rod mills is described. The system has bee,, tested at CODELCO E1 Salvador Concentrator where, due t,, variations on size distribution of the copper ore feed, th' rod mill is frequently subject to overloads. The main inpur signal to the system is the rod mill sound, after being measured and analog conditioned. This signal and othe signals measuring the fresh ore feed and the mill watt addition are fed to a computer containing a simpl mathematical model. The model parameters are empiricall estimated and an analog output signal is generated, whic gives an early prediction of the overload condition. The experimental results described in this paper show that the overload condition may be predicted with an anticipation of about three minutes.

Jan 1, 1985

By R Hughes

"Spring Creek Mine uses high pressure water to extract the thick Main seam in the Upper Rewanuicoal measures. The extraction method results in the creation of large voids which collapsespontaneously. This can result in the displacement of large volumes of methane, which may create a signifi cant hazard if not correctly managed. A system of automatic dilution doors is employed to mitigate this risk. This paper describes the evolution of the system and gives some examples of its eff ectiveness."

Jun 1, 2012

By R Lau

In recently completed road tunnel projects in Queensland, such as the Airport Link and the Clem7 tunnels, there is a smoke duct running along the roof of the carriageways to extract smoke in case of fire. In New South Wales, no road tunnels have a smoke duct. In the Melbourne City Link tunnels, there is a small smoke duct running along the roof. All of the tunnels are safe as claimed by the designers and authorities. However, there is significant cost associated with providing a full size smoke duct compared with no smoke duct. This paper is going to present a comparison of the road tunnel safety with a smoke duct and those without one from a risk perspective. It further discusses the cost-effectiveness of such provisions and whether similar levels of safety could be achieved without a smoke duct.CITATION:Lau, R, 2014. Smoke duct or no smoke duct for road tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 83–86 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By G Billing a, D Gribble, E Hall, D Varga

The theoretical benefits of electronic detonators have been reasonably well documented. To support this, a practical comparison was made between the performance of the standard shock tube system, NONEL, and a high precision electronic system, HotShotÖ, at the Sunrise Dam Gold Mine. The expected benefits from electronic detonators to Sunrise Dam were identified prior to the trial. Based on these, a number of objectives were set to demonstrate the value of the HotShot system. These are an improvement in fragmentation leading to an increase in productivity, less oversize rehandling, increased throughput and more uniformity in muck pile movement. To maintain the integrity of the trial, the nominal timing of the shots was kept exactly the same, thereby restricting any performance improvements to the precision of the electronics. Accordingly, adjacent shots were chosen with consistent geology. Video footage was taken of the blasts and vibration monitoring was carried out by fixed geophones throughout the mine. Spot heights of the muck pile swell were taken immediately after the blast and heave profile graphs were generated for comparison. Video footage was taken for a period of three hours for both shots to analyse cycle times of the excavator and trucks. PITRAM data was also collected for analysis. As far as practicable, the ore was taken to the same finger on the run-of-mine (ROM) pad to assist in single sourcing for the crusher and to allow oversize to be separated out. From specific metrics taken during the trials, it was shown that the expected improvements due to the high precision timing of electronics were realised in all areas.

Jan 1, 2007

The Mineral Resources Act 1989 was assented to on 25th October, 1989 after more than two years of consultation and negotiation between Government, the mining industry and other affected parties particularly the major rural organisations.The legislation proposes major conceptual changes in a number of areas and adopts a totally new approach to the definition of land and the mechanisms available to the mining industry for accessing such land.Unfortunately the passage of the legislation through Parliament coincided with the lead-up to the State election. Ultimately it became an election issue generating much adverse comment in the media particularly from rural and landholder groups. It was obvious that much of this anti-mining propaganda resulted from a lack of understanding of the legislation and the benefits that flow to the majority of landholders as well as the mining industry.It is essential that the contents of the Mineral Resources Act be thoroughly understood by all parties. Only then will all the State's resources be able to be developed in a multiple land use environment.This paper outlines the philosophy behind the new Act and the more important provisions contained therein.

Jan 1, 1990

By M Lund

Due to operational and regulatory practicalities, pit lakes will continue to be legacies of many open cut mining lease relinquishments. Unplanned or inappropriate management of these significant geographical features may lead to a short-term liability to all stakeholders during mining operations, or to ongoing liability to the local community and environment following lease relinquishment. However, the potential for pit lakes to provide benefit to companies, communities and the environment is frequently unrecognised and yet may be a vital contribution to the sustainability of the open cut mining industry. Improved remediation technologies are offering more avenues for pit lake end use than ever before, at the same time mining companies, local communities and regulatory authorities are also becoming more aware of the benefit these water resources have to offer. Sustainable pit lake management aims to better minimise short- and long-term pit lake liabilities, and yet also to maximise short- and long-term pit lake opportunities as well.

Jan 1, 2006

The Prince Lyell Mine has been the major production source at Mount Lyell since under-ground mining commenced in 1972.Three lifts of stopes have been mined to date, with the fourth, the 40 Series lift, to commence production this year. As the mine has progressed deeper, the ore haulage system has evolved to accommodate the mine's economic circumstances while maximizing efficiency.In the first, or 10 Series lift of stopes, ore was removed from drawpoints by L.H.D. units and tipped directly into rakes of 7 tonne rail cars. The original concept for deeper stoping lifts entailed L.H.D.'s tipping into long ore passes, rail haulage, underground crushing and hoisting to surface via the No. 1 Shaft. The suspension of the No. 1 Shaft project in 1976, due to economic difficulties, lead to the intro-duction of diesel truck haulage of ore, initially via the internal Prince Lyell Decline and now to surface via the Main Decline.

Jan 1, 1985

The increasing global demand for rough materials forces almost every mine to look at the mechanisation in their processes. This will not onlyimprove performance but with safety issues becoming more and more prevalent, the need for the introduction of mechanisation technologies to mining applications is essential. Ongoing developments are occurring in almost every field, ranging from basic developments to specialised mining. Mechanical tunnelling and shaft sinking have set the standards regarding safety, profitability and environmental protection. Different machine types and working principles have been developed to suit the geological and hydrological requirements of tunnelling projects worldwide. Continuous activity in research and development leads to constant optimisation of tunnelling performance.

Jan 1, 2008

By A F. Cooper

The northeast-southwest trending ~25 km2 area incorporating Bald Hill is located 18 km northeast of Haast, and 5 - 7 km west of the Alpine Fault in South Westland, New Zealand. The geology consists of Greenland Group greywacke overlain by a Cretaceous-Tertiary sedimentary sequence and fluvio-glacial/marine terrace deposits of Quaternary age. Alluvial gold in Cole Creek, draining west from the summit of Bald Hill, may be derived either from vein mineralisation in basement rocks or from fluvial or marine terraces.   This paper focuses on the potential for in situ gold and base-metal mineralisation in sporadic, siderite-rich quartz veins that cut basement greenschist facies metasediments that have been overprinted by contact metamorphism.   Throughout the area, vein compositions are dominated by quartz and commonly feature zoned plagioclase. Alteration adjacent to veining within the contact aureole is dominated by 1 - 2 mm, coarse grained biotite, with small amounts of sulphide, and is pervaded by abundant siderite veinlets. Outside the aureole, wall rock alteration to veins consists of fine grained chlorite. Trace element XRF analysis has been used to ascertain base metal concentrations within samples of vein and alteration zones collected from throughout the area. Vein and alteration zone mineral assemblages containing <5 per cent sulphide, with low concentrations of As, Cu, Pb and Zn indicate low potential for gold and base-metal mineralisation in the Bald Hill region. Contact metamorphism of Greenland Group basement in the northeast of the region, is likely due to emplacement of a poorly exposed Cr- and Ni- enriched gabbro. The presence of biotite and andalusite in hornfelses indicate contact metamorphism occurred at temperatures >350¦C and at depths <10 km. Widespread vein distribution does not appear to be related to contact metamorphism or gabbro emplacement. Further research is required in order to establish the fluid source from which the veins were precipitated.

Jan 1, 2007

By Honey F. R, Furnell R. G, Lyon R. J P

A Joint Venture between Union Oil Development Corporation and Geoscan Proprietary Limited carried out an Airborne Multispectral Scanner Survey over approximately 15,000 square kilometres in the Charters towers area of northeastern Queensland during late 1985 and in September, 1986. The survey, using the Geoscan Mark I scanner, consisted of 50 runs each having a swath width of 5 kilometres. Twelve or thirteen spectral bands were recorded, 5 in the VNIR, 4 in the SWIR and 3 or 4 in the TIR. The results of the survey were interpreted by interactive image processing with the aim of identifying those minerals or their weathering products which are characteristically associated with hydrothermally emplaced gold mineralisation in this part of Queensland. Spectral bands in the VNIR were used to identify and discriminate the iron hydroxides, whilst the SWIR bands were used to outline the clay and carbonate rich areas. The TIR aided in identifying areas of silicification.

Jan 1, 1989

By Grant JR, McKavanagh BM, Dear SJ

A geophysical technique of rock mass assessment for engineering purposes is being investigated and shows positive correlation with direct structural logging and mapping techniques for the detection of major geological features. The technique is cross-hole acoustic surveying incorporating high speed signal averaging, with a maximum hole separation in excess of 30 metres in hard unfractured rock masses. The bulk of the field test work was carried out in open stopes in the copper ore bodies of Mount Isa Mines Limited. The investigation forms part of an integrated study of blasting in mining, aiming for fragmentation control through blast design modification. The rock quality factor, Q, is presented as a blasting index and can be determined for a significant portion of a production stope.

Jan 1, 1981

Two main aspects need to be considered when analysing a potential petroleum development project. Firstly, an estimate of the recoverable reserves must be made, and in many instances, these reserves must serve as collateral to finance development if outside capital is required. Secondly, the likely production profile and cash flow has to be established, and this cash flow then must meet debt service require- ments and in addition generate the required profits. In making these crucial deter- minations, the impact on the project of a wide variety of risks has to be analysed. A computer model, which represents the project in its entirety, is a great aid in determining project viability. Such a model requires imput from geologists, engineers and economists, and interpretation of the model must also be a joint effort. Communications, and inter react ion amongst individuals and disciplines is essential if the best answers are to be obtained

Jan 1, 1983

By Boyd G. L

Stress measurement is at the core of most stability design analyses. It is demonstrated that contrary to accepted practice, it is the field measurement, and not the calculated prediction, of stress that requires most examination and review. Since it is not really possible to quantify rockmass properties, the stiffness values used in reduction of stress measurements and in subsequent design analyses (either empirical or numerical modelling) must consider an appropriate range of values.

Jan 1, 1995

CONTENTSIntroduction.Ore Bodies.Variations in Ore Dressing Practices.Stage I .Gravity Concentration for the production of a Lead Concentrate. 1909-1918.Stage Il Gravity plus Flotation Treatment for the production of a Lead Concentrate and a Zinc Concentrate. 1918-1929.Stage III All Flotation Treatment for the production of a Lead C~mcentrate and a Zinc Concentrate. 1930-1939General Summary - Stages I, II, III.Stage IV Gravity plus Flotation Treatment for the Production of a Lead Concentrate and a Zinc Concentrate. 1939-1947.1. General.2. Notes on Ore Dressing Practice.A. Gravity Section - Re~oval of Free Galena.B. Secondary Ball Mill Grinding Section. .a. Mineral Association.b. Composite particle problem.c. Degree of grinding required.d. Free Gangue Minerals in Table Tailing.

Jan 1, 1948