Search Documents

In 1975, following a programme of solution characterization and small scale laboratory test work, a pilot plant was constructed to treat waste liquors from the Risdon works. The plant was designed basically to neutralize liquor to a desired pH, and to flocculate, thicken and then filter the resultant pulps. The primary objective was to purify waste liquors to stand- ards set by Tasmanian environmental regulations and at the same time to provide design data for construction of a full scale treatment facility. Waste liquors were divided into two groups, those from the Zinc Plant, and those from the Acid and Superphosphate Plants, and were treated independently. To satisfactorily purify Zinc Plant waste liquors the following reaction sequence was required: 1. Neutralization to pH 10.5 (with aeration for Mn removal). 2. Further reaction of neutralized pulp with Na2S at an addition rate of typically 5 mg of S2-/litre of liquor treated to remove Cd.

Jan 1, 1977

By Van Hoorn PD

For the development of BHP's Gregory open cut coal mine in Central Queensland a mini computer was successfully used to assist staff in the evaluation of the deposit and the planning of the mine. The Gregory deposit is essentially a single mineable seam deposit, however the systems developed may be applied to other coal deposits including multi seam occurences. The first phase of the Gregory computer evaluation and planning project involved the establishment of a borehole data base for the storage, retrieval and analysis of both strata and quality data. During the second phase a numeric block model of the coal deposit was created. Using this model reserve calculations were carried out by specifying the area with the aid of a digitizing tablet. The third phase involved the develop- ment of systems to simulate the dragline stripping operations including the rehandle percentage calculation, a dragline production schedule showing coal quantity and quality exposed, and a combined multi dragline operation schedule that can produce figures and graphs for up to 20 variables. A derivative of the operating plan was a programme that gave productioh cost estimates

Jan 1, 1978

An improved technique for the quick and accurate measurement of the weight and centre of mass in the horizontal plane of large machines has been developed. On-site weighing of large plant such as bucket wheel dredgers is an important part of the commissioning procedure. The results from the weighing assist in determining the stability of the machine and also enable confirmation of the structural weight distribution used for stress analysis at the design stage. In this paper the techniques previously used for weighing are reviewed and the sources of error using these methods examined. A full descrip- tion of the current technique and procedure is given explaining how the measurement system comprising strain gauge load cells, displacement transducers, wind speed and direction sensors, data logger, computer and software was developed to enable quick and accurate measurements to be made. Proposed modifications to software necessitated by the replace- ment of current measuring instrumentation and computer are discussed. A typical example of measurements from the weighing of a large dredger, illustrating the accuracy of the new technique is given and the calibration technique used to check the accuracy of the force and moment measurements is explained. An outline of how the results are used to certify the machine for operation is given.

Jan 1, 1989

Brand se Baai, on the North-Western Cape Coastline of Southern Africa, is the site of the Namakwa Sands Limited Heavy Mineral Sands Mining Operation. The mine is a 14 000 000 tonnes per annum open-cast strip-style mining operation using truck and excavators to mine the sand. The orebody consists of relatively unconsolidated sands reworked by fluvial, marine and aeolian mechanisms. The total orebody includes three primary ore types, namely the Red Aeolian Sands, the Dorbank (a hardcap layer) and the Orange Feldspathic Sands, which forms the bulk of the resource. Mine planning and scheduling is done using a 50 m + 50 m variable bench height system with three primary bench heights. The Aeolian and Dorbank each have a bench that varies with their thickness of up to a maximum eight metres and the Orange feldspathic sand, a standard bench height of eight metres. For a number of years Namakwa Sands used a complex 2D, Datamine Based, macro system to perform the resource evaluation and mine design. As the mining operations expanded it became clear that a complete system redesign was required to cope with the increasing operational pressures coming to bear on the old system. The biggest challenges facing any replacement system are the sheer scale of the mining operation (16 km long and 7 km wide resulting in a minimum of 30 000 individual 50 m + 50 m mining blocks), the size of the geological data files (up to one gigabyte) and representing the benching system accurately (as the benches follow the topography and are not horizontal). In addition to these large-scale issues, the ability to run multiple mine design scenarios was required, an aspect which the old system was unable to perform adequately. Based upon these primary difficulties, a new business process was developed which required a complete rethink of the mine design methodology as well as the creation of a new system to deplete the resource model, produce monthly reconciliation evaluations and create a ultimate pit limit based on the operations mining cost model. Using a system based on the Earthworks Mine2-4D Mine Design and Scheduling System (with its mine design and scheduling specific tools), as well as a small, customised program, massive time-savings have been made. It is now possible to run several life of mine scenarios in the same timeframe that a single life of mine run took under the old system. This paper will present the methodology and business decisions behind the new Namakwa Sands system, and detail the restructuring and development used to deal with the large data set sizes and long processing times inherent in the old system. Future enhancements to the system that will make it more generically applicable to open-cast mining scenarios will also be dealt with.

Jan 1, 2003

By Lauha E. A

The Goldstrike Mine is in Eureka County, Nevada, U.S.A., approximately 23 miles northwest of the town of Carlin. The mine is at the north end of the Tuscarora Spur of the Tuscarora Mountains at elevations of 5,300 feet to 5,950 feet. It is part of the Bluestar/Goldstrike subdistrict of the Carlin Trend, a northwest alignment of sediment hosted, disseminated gold deposits. The Carlin Trend includes over 15 major gold deposits with production, reserves and geological resources of approximately 65 million ounces of gold (Figure 1). In the Bluestar/Goldstrike subdistrict, there are seven major deposits; Betze, Lower Post, Post, Genesis, Bluestar, Purple Vein and Deep Star, plus numerous smaller deposits (Figure 2). Production, reserves and resources for the subdistrict are approximately 40 million ounces. Betze and Purple Vein are located on property controlled by Bamck Goldstrike Mines and Bluestar and Genesis on Newmont Gold property. Post, Lower Post, and Deep Star occur both on Barrick and Newmont Property.

Jan 1, 1991

By Diessel C. F K, Ng N

The commonly used Stopes-Heerlen coal petrographic classification and nomenclature has over the years been subject to variable interpretations. This paper discusses the problem with specific reference to the inertinite maceral group. The effect of various interpretations of the Stopes-Heerlen system on maceral analysis is discussed and illustrated by means of comparative analyses conducted by a number of laboratories in Australia. An attempt is made to define the reflectance thresholds used by the authors to subdivide the inertinite group; the genetic and technological significance of these thresholds are compared. The difficulties of distinguishing structured and non-structured macerals of the inertinite group is discussed in terms of possible improvements to the present Stopes-Heerlen system by extending the classification to include transitional maceral types.

Jan 1, 1969

By E Giles

Pike River Coal Limited (PRCL) is opening a new underground coal mine in the Paparoa Ranges north-east of Greymouth. To access the coal reserves, PRCL have had to build a 13 km access road through regrowth and virgin forest, and appointed McConnell Dowell Constructors Limited, with URS New Zealand Limited as their consulting engineers, to construct the final access link: a 2.3 km long, 5.5 m wide and 4.5 m high incline tunnel. This paper discusses the logistical issues of construction in an isolated pristine forest in mountain land and how they were addressed. It provides an overview of the 90 per cent complete tunnel and how challenging rock conditions have been mastered. It outlines briefly the remaining work which is construction of pit bottom workings where the mine infrastructure will be housed and construction of a 110 m deep, 4.0 m diameter, vertical ventilation shaft.

Jan 1, 2008

By Ramani R. V

In this paper, a comparative performance evaluation of geostatistical, spectral, and fractal methods is made for short-scale variability prediction. The algorithms compared are: sequential Gaussian simulation method; a random fractal algorithm based on the generalised stochastic subdivision method; and a spectral simulation approach adopted for direct multi-dimensional simulation. The data for this study have been obtained from a mined out coal property. As this property was being mined, a 7315 m by 7315 m (24000 ft by 24000 ft) coal block was extensively sampled at an approximate spacing of 107 m (350 ft) and the 60-ton samples were analysed for sulphur in the 1.50 float gravity fraction. This data set is used here with the three methods to generate the simulated realisations, which are analysed for semivariogram reproduction and for simulation errors. Although all three methods converge to the true semivariogram in an average sense, the coefficient of variation of the average semivariogram for the Fourier integral method is minimum. The realisations generated by the sequential Gaussian method have minimum mean simulation error. The choice of a simulation method based on variability reproduction and simulation errors remains difficult.

Jan 1, 1995

Laboratory studies of batch and continuous screening of ferrous sinter mixtures (4-0.5 mm) are described. The results are analysed by an equation derived from the first-order rate law for the condition of decreasing screen residue.The results of the studies show that the two screening operations are comparable in all respects if deck length in continuous screening and time in batch screening are interchanged.It is shown that the general screening process is determined by the numerical values of the screening rate constants of each of the particle sizes in the feed mixture and that the relationship between these constants and the particle size/screen aperture ratios is related to the appropriate probability function of the same ratios.It is also shown that the screening rates decrease exponentially with the amount of near-mesh material present in the feed and that oversize particles can increase these screening rates for some screen motions and decrease them for others.

Jan 1, 1985

Initial coal production at Ulan was solely from underground mines. A significant increase in demand for steaming coal in the late 1970's emphasised the need to further expand production and led to the development of the open cut mine which commenced commercial production in June, 1982.During the initial stages of mine planning, feasibility and cost studies were undertaken to determine the most suitable method for coal haulage from the pit. The comparison between a conventional truck haulage system and an in-pit crushing system using a mobile crusher and moveable belt conveyor haulage confirmed that the mobile crusher and conveyor system was superior in every respect for the Ulan mining operations.Technical features and design parameters for the major items of equipment are outlined as well as operating, manning and performance assessments. Minor equipment problems were encountered during initial operation but these have since beenrectified and the plant is now capable of exceeding the design production. Maintenance and energy costs are considerably lower than originally estimated and production efficiencies are continually improving as operators develop new techniques and procedures in the handling of the equipment.

Jan 1, 1985

By H Kusumi, A Nishio, K D. Halim, Y Yun

In Japan, evaluation of rock mass is crucial in mountain tunnels that are constructed using the NATM (New Austrian Tunneling Method) to determine the support pattern that in turns determine the final support structure of the tunnel. The current evaluation method is highly dependent on the observations of on-site expert engineers that grades the rock mass in four levels across nine criteria: A. Condition of tunnel face. B. Condition of excavated surface. C. Compressive rock strength. D. Weathering. E. Spacing of discontinuity. F. Condition of discontinuity. G. Orientation of discontinuity. H. Spring water. I. Water degradation. However, in recent years, the number of said experts are decreasing rapidly due to labour shortage caused mainly by an aging population and declining birth rates. This is one of the biggest challenges that the construction sector currently faces, and this may affect the efficiency of tunnel construction projects in the future. Thus, this study proposes the implementation of a deep learning tool called the convolutional neural network (CNN) to quantitatively evaluate rock fractures on tunnel face. In addition, Gradient-weighted Class Activation Mapping (Grad-CAM) is applied to visualise CNN, as well as verify the applicability of CNN to the evaluation of rock fractures. In other words, by creating heat maps of tunnel face images, CNN is utilised to evaluate rock mass in categories that are associated with discontinuities. The CNN model is most accurate when six convolution layers, four pooling layers, and three dense layers are used. This yields an accuracy of 75.0~88.0 per cent. Thus, the CNN model is verified to be feasible method to evaluate rock fractures.

Nov 29, 2022

The considerations which led to the decision to_ install discs at the Dampier Pellet Plant of Hamer ley Iron Pty. Ltd. are described. Initial testwork showed that the ore could be ground dry in open circuit to a Blaine index of 2500 cm2/g and that it pelletized readily. The various design criteria including diameter, slope, speed, motor size, depth of sidewall, feed point and water spray location were then determined. Plant performance after commissioning is described including the various problems encountered and the modifications since carried out to overcome them. The main problem was quickly identified as disc feed rate control. Various bin and bin feeder modifications were tried to overcome the effects of the fluidising characteristics of the dry ground ore. Other factors found to affect disc operation are ore size distribution, additives and operator competence.

Jan 1, 1974

There is considerable economic incentive to increase the angle of open pit walls so as to reduce the total volume of waste to be moved to gain access to an orebody. However, a number of slope failures has increased the awareness of mine operators to the potential and consequences of slope failure. Sophisticated methods for the analysis of slope stability have been developed but they rely on an understanding of the appropriate parameters to describe the structural properties of the slope materials. Unfortunately, these properties change with time.The excavation of an open pit mine removes the constraint and weight of the overlying material and allows the newly formed slope to release previously locked in stress. The release of this stress allows the opening of joints and leads to a significant reduction in bulk modulus. The rock mass is also further affected by damage from nearby blasts. Such damage is cumulative and further reduces the modulus of the near surface material and weakens the bonds between structural elements in the slope.

Jan 1, 1992

The most critical step in the development of any mining project is the completion of a feasibility study. The feasibility study has one primary goal; to demonstrate that the project is economically viable if it is designed, constructed and operated in accordance with the concepts set forth in the study. Starting from a mineral resource data base, the feasibility study will define the ore reserves, the mining methods, the mineral processing concepts and the scale of the project. The disciplined activity of developing a feasibility study leads the proponent to examine every aspect of the project, many of which might otherwise be ignored. All technical concepts will be established and the corporate philosophy with respect to organisational structure, social and environmental responsibility, infrastructure contributions and financing will be determined. All the major decisions about how the project will be developed are made during the feasibility study. The success of the project will then depend upon the assumptions and decisions in the feasibility study and the ability and empowerment of the development team.

Jan 1, 1997

By B Muller

The disposal of tailings has become a greater issue due to the changing economics of mineral extraction. The processing of lower grade deposits and tougher environmental regulations has led to the selection process for tailings disposal options becoming more complicated. Current selection methods are too time consuming or too easily manipulated for inexperienced users to use successfully. This paper examines a different method for the initial selection of a tailings disposal system, using a numerical system that was introduced into the mining method selection field. The numerical method system was compiled by reviewing previous work done on the positive and negative aspects of the tailings disposal methods used by the coal and metallurgical mining industries. Assessing the common trends and design aspects of each of the methods was undertaken and a ranking was designed to explain how well suited the tailings disposal methods are to a situation. The tool successfully analysed sites using common data to indicate methods for disposal that would have provided minimal technical problems, low environmental risk and been practically possible. The tool also proved successful in identifying critical areas that would need further investigation. This new system was tested on some disaster case studies from around the world in order to show that it could have successfully selected a different method for tailings disposal that would have prevented the disaster.

Sep 26, 2011

This paper presents results of the experiments carried out in Beth Energy No. 33 Mine for the purpose of alleviating problems associated with cutter roof. Cutter roof problems have delayed the advance of the entry development considerably and maintenance cost of these entries was very high due to the requirement of very extensive and heavy artificial supports. The study includes assessment of the problem, investigation of the geology and lithology of the mines, study of in-situ stresses and corrective measures to combat the problem. Two approaches were selected as the corrective measures: 1) implementing yield pillar concept in order to reduce the effects of in-situ horizontal stresses, 2) designing an effective roof reinforcement system and application procedure. Results of this study revealed that roof strata is weak and in-situ stresses are very high at the problem area which results in development of cutter roof. Implementation of yield pillar concept was found to be ineffective because cutter roof often developed at the entry face concurrent to the development. However, proper design and implementation of roof reinforcement system stabilized the roof and eliminated roof caving during both entry development and retreat of longwall face, despite existence of the cutter roof, at a much lower cost.

Jan 1, 1992

By L M. Zhang, T H. Xu, J Zhao

Blasting is one of the most commonly used strategies for excavation in civil and mining engineering. Yet blasting can also bring along such undesirable effects as ground vibrations and soil disturbance. Numerical analysis is a powerful tool for estimating the effects of blasting and improving blasting design. In this research, a constitutive model for sand is proposed for the numerical analysis of blast-induced ground motions and wave propagation in soil mass. In the model, three model surfaces, ie the critical surface, the dilatancy surface and the bounding surface, are defined following the bounding surface hypoplasticity framework. The strain rate is included explicitly into the model formulations so that the proposed model is valid under high strain rate loadings caused by blast-induced vibrations. The performance of the proposed model is validated by the simulation of drained triaxial compression tests conducted on a crushed coral sand under different strain rates.CITATION:Xu, T H, Zhang, L M and Zhao, J, 2014. A bounding surface model for sand subjected to blast-induced vibrations, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 201–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By J E. Everett

Maximising ore tonnage at a selected target grade requires that appropriate ore identification criteria be established. Iron ore mining block models may consist of many millions of estimated blocks, each block corresponding to the selective mining unit (SMU), with grade interpolated from drill hole data. Each block can be considered as a potential ore candidate. Analysis of such a huge database can require large computational resources, especially for sensitivity analysis requiring multiple computations. However, an alternative streamlined approach is possible, where the data are compressed to an appropriately smaller and representative subset. The consequent data reduction not only makes it feasible to consider the simultaneous analysis of multiple pits but also considerably speeds up computation, enabling sensitivity analysis of the potential ore tonnage as a function of the required grade. Ore identification criteria can be successfully established using appropriately chosen reduced data comprising less than one per cent of the blocks. The ore identified is virtually indistinguishable in tonnage and grade from the ore that would be selected using the entire block model.Two methods of data reduction are tested: sampling (using a proportion of unaltered blocks) and binning (consolidating groups of blocks to a single average grade). The source blocks are first sorted (such as by location, analyte grade, principal component score, random order or value) before sampling or binning. In this study, the sorting options considered were by location and Fe grade. The effectiveness of each method was evaluated using the block model subsets to select the maximum tonnage of ore at a specified target grade. Block model data from an anonymous Pilbara iron ore project with about one million blocks averaging 1.132 kt were used. The blocks are from multiple resource models, to be blended to a single product. Sampling is shown to be superior to binning because sampling preserves the full variability while binning, although matching the mean block grades reduces their variability.It was found that the appropriately sampled data sets (sorted by location) gave results virtually identical to the results for the full data set, even when the samples comprised less than one per cent of the original blocks. The reduction in computer time to identify maximum tonnage at a specified grade was approximately proportional to the sample percentage. The increase in computation speed greatly facilitated sensitivity analysis. A sampled data set of one-eighth the total block model was used to investigate the effects of changing each of the component grades around the original grade specification. The results of this sensitivity analysis are discussed, and illustrate the potential benefit of carrying out sensitivity analysis in determining feasible and marketable product grades.CITATION:Everett, J E, 2015. Block model data reduction and sensitivity analysis, in Proceedings Iron Ore 2015, pp 263–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By M Iglesias-Martínez

The potential for iron ore in the Central African Archean belts has received much less attention by comparison to their equivalents in other cratonic regions of West Africa, South Africa, Australia and Brazil. Historically, iron ore is known to occur in South Cameroon and North Gabon with significant iron ore deposits (eg Mbalam in Cameroon, Avima in the Republic of Congo, Minkébé, Bélinga and Boka-boka in Gabon), having been the subject of geological exploration programs carried out by government institutions and exploration companies. Although the presence of strong aeromagnetic anomalies, undeniably related to the presence of greenstone belt formations, has been recognised, this study is the first attempt to assess the potential of banded iron formations (BIF) in the Northern part of the Gabonese Republic in the region between Minvoul and Minkébé (>10.000 km2). Deep lateritic weathering, inaccessible equatorial rain forest and high operational costs are some of the reasons why only limited exploration has been undertaken in the area. This work aims to improve the geological knowledge and to highlight the potential for iron ore of the eastern margin of the Ntem Complex units dated between 3.3–2.7 Ga. Field work showed a series of mafic rocks (amphibolite, anorthosite and gabbro), schist and BIF (described as itabirites in neighbouring areas). Samples from Minvoul BIF showed an extensive and deep weathering to powdery hematite revealing the presence, in thin sections, of iron oxides including magnetite, hematite and martite, primary and secondary quartz, garnet, hornblende, anthophyllite, cummingtonite and epidote. Mineral assemblages and coarse grain size suggest a metamorphic grade ranging from medium to upper amphibolite facies. The existence of known economic iron ore deposits in neighbouring regions combined with an extensive weathering enrichment process are promising factors for potential iron ore discovery in this remote area.

Sep 18, 2023

By Roberts AW

Bulk materials handling operations depend on efficient storage and gravity flow facilit- ies. ,It is important that proper attention be given to the complete storage bin or stockpile and feeder combination. The paper briefly des- cribes the principles of efficient feeding and discusses the common types of feeders under practice. While ideally unaided gravity flow should be sought, occasions arise where flow promotion is necessary. Various types of flow promotion devices are described and their operational features evaluated.

Jan 1, 1978