Search Documents

By Y K. Leong

Iron ore tailings typically containing 40 to 50 per cent Fe can be beneficiated to iron ore products containing 54 to 60 per cent Fe. The impurities are comprised of clay, quartz, cristabolite and TiO2. Goethite and hematite are also present. At high concentrations of 55–60 wt% solids, the tailings displayed high yield stress and viscosity and cannot be pumped over long distances. Composite additives comprising of NaOH, phosphate-based additives and sodium metasilicate are found to reduce the viscosity and yield stress very significantly by a few orders of magnitude. The yield stress of 100 Pa can be reduced to almost zero. At this state, dilution of the tailings with its process water to 40 per cent solids causes the coarse and high-density iron ore particles to separate from the colloidal fractions located in the supernatant after a few minutes of sedimentation. Separation by decantation produces a sediment with an Fe content of 54 per cent from tailings with 47 per cent Fe. Another tailings sample with 48 per cent Fe was beneficiated to greater than 57 per cent Fe using NaOH-metasilicate-polyphosphate additives and employing an additional washing step. The use of other composite additives, NaOH and polyphosphates, increased beneficiated product Fe content to greater than 60 per cent from the same tailings. With the current iron ore spot price of more than US$180 per tonne, the cost of this treatment process even including a desalination step, if necessary, is relatively insignificant. This study has given tailings an economic value that should be exploited as soon as possible.

Nov 8, 2021

By I T. Ross

Sampling drawpoints in block cave mines has been a contentious issue for many years. Doubts have been expressed as to the validity of the process used at most mines. This paper outlines the sampling practice commonly in use, discusses the resulting issues associated with reconciliation and drawpoint closure decisions. The paper also looks to the future and highlights issues for some block cave mining operations currently planned to have in the order of one thousand active drawpoints. It is likely that these operations will require a new approach to drawpoint sampling. There are several potential technologies currently available although some appear to be better suited than others to replace the current approaches. CITATION:Ross, I T, 2012. Sampling in block cave mines, in Proceedings Sampling 2012 , pp 81-86 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By A Liu, X Wang, W Peng, Q Zhang

Pulp rheology plays a critical role in fine mineral flotation. Yield stress and apparent viscosity are two important rheological parameters affecting mineral flotation recovery. In this paper, the concept of pulp rheology and its measuring method are presented. The main factors, such as particle size, pulp concentration, mineral types, pulp temperature, inorganic salts, that affect the pulp rheology are systematically reviewed, and then followed by the discussion of the relationship between pulp rheological properties and flotation performance. Generally, high pulp apparent viscosity and yield stress values have been found to have an adverse effect on flotation recovery. In addition, due to the hetero-coagulation between the valuable mineral and gangue mineral, the pulp of mixed ore shows higher viscosity than that of the single mineral slurry. This paper is expected to provide some references for the efficient upgrading of low-grade and complex ores from the perspective of pulp rheology.

Aug 24, 2022

By Ryan A, Dennis R, Dekker D, Ellis W, Sowerby B

An automated facility for non-destructive elemental analysis of mine samples has been developed and tested at Mount Isa in association with the CSIRO. The analysis is based on the prompt and delayed measurement of gamma radiation emitted by the sample during and after separate fast and thermal neutron irradiation. No sub-sampling or sample preparation is required and the analyser is operated by one person that would otherwise be splitting drill core in preparation for conventional analysis. The analyser has been calibrated to measure the following (precision in parenthesis): Ag (14 ppm), Pb (0.5 wt%), Zn (0.5 wt%), Cu (0.04 wt%), Fe (0.7 wt%), S (1.1 wt%), SiO2 (0.8 wt%), A1203 (0.07 wt%), Mn (0.05 wt%), specific gravity (0.02 g cmt). Crushed or whole drill core samples that range in size between 0.5 m and 1.8 m of equivalent BQ size drill core can be analysed at a rate of six samples per hour. If required, drill core samples can be re-packed in their original configuration for storage following analysis. Standard samples are measured every day to ensure operational stability. The analyser is controlled by a personal computer which prints the results and stores them along with the raw data on the computer hard disk. This paper reports the performance of the analyser during 1992 for routine analysis of drill core from the lead ore bodies of both Mount Isa and Hilton mines.

Jan 1, 1993

The Hodgkinson goldfield contains over 50 separate lodes which have produced 9.7 tonnes of gold from ore averaging 37 g/t. The gold-quartz.lodes are spatially separate from tin and base metal mineralisation, associated with Permo-Carboniferous granitoids in the province. Host rocks consist of sub-greenschist metamorphic grade shale, conglomerate, sandstone, spilite, chert and melange. Oreshoots average 100 x 30 x I m in Size and are contained in cross-cutting quartz. filled with steep-dipping shear zones. Mineralisation in the quartz. consists of gold with minor arsenopyrite, pyrite, galena, and sphalerite with rare calcite. Scheelite and stibnite are aSSOCIated locally but are not necessary proximal or coeval. Alteration is restricted to centimetre-scale phyllic selvedges adjacent to the veins and veinlets.Most of the lodes and vems occur within six main 1.5 x 0.25 km mineralised areas whIch may indIcate separate areas of fluid flow and precipitation. Ore controls differ m melange- and sandstone-hosted lodes but several features are common to all the oreshOOlS. Most of the lodes occur within zones of duauon that are caused by splaymg, refraction through carbonaceous shale-sandstone contacts, or by rolls and changes in strike and dip.Lithologic contacts may act as areas of permeability and chemistry contrast which focus fluid and precipitation. Tensional veins are common between parallel shear zones and curved spur veins occur both in the hangingwall and footwall of the main fissure. Intersections and contacts may have enhanced local fluid flow in many of the areas.

Jan 1, 1991

By P Odins

Traditionally, stratigraphic deposits have been represented by a large number of gridded surface and product analytical models, related to each other by naming convention. This approach, though suitable for structurally simple stratigraphic deposits, does not lend itself well to addressing the complex style of stratigraphic deposits which are becoming more prevalent. In addition, the sheer number of individual gridded models involved makes it very difficult to keep a consistent audit trail of the overall deposit model. Recently, a new enhanced block model structure known as Horizon Adaptive Rectangular Prism (HARP) models was introduced to address these issues. An HARP model is specifically designed to allow stratigraphic units to be represented with virtually no loss of structural integrity, by allowing the tops and bases of the individual HARP blocks to ‘bend’ in concert with the input surfaces. By bringing together the best of grid modelling, triangulation modelling, block modelling and grade estimation, the HARP model opens up many exciting new opportunities for the stratigraphic geologist or engineer to take their model further than was previously possible. Examples of improvements in modelling methodology using a HARP model include: the ability to represent complex normal, reverse and thrust faulting; the ability to store thousands of additional analytical, geotechnical or calculated variables in each individual block; advanced visualisation, manipulation and plotting capabilities; and the ability to calculate volumes and resources against complex, three-dimensional (3D) solid pit designs. Finally, several ‘real world’ scenarios, illustrating how this advancement in modelling technology can benefit a wide range of mining professionals are detailed. These examples demonstrate how productivity gains can be made in both long-term resource modelling and short-term ‘week by week’ geological modelling as an adjunct to mine planning.

Aug 22, 2011

By M Barkh, F X. Spachtholz

The mining industry faces significant environmental challenges in managing tailing ponds and wastewater treatment, including the risk of contaminated water, breaches of tailing dams, and energy-intensive treatment processes. Traditional methods involve pumping water to secondary treatment facilities for neutralisation, which is costly and poses operational and environmental risks. In response to these challenges, the Professional Mine Water Action Plan (PMAP) introduces a revolutionary approach that combines cutting-edge AI technology and environmentally friendly reagents for in situ neutralisation of acidic wastewater. PMAP leverages magnesium-based slowrelease reagents and AI-driven intelligent dispensing systems to optimise treatment processes within the tailing pond itself. The unmanned smart dispensing vessel (USDV) conducts bathymetry to gather data on water quality and hydrography, allowing the system to determine the appropriate reagent quantity and injection strategy. This approach transforms the tailing pond into virtual reaction columns, enabling individual and simultaneous water treatment while optimising efficiency. PMAP’s novel reagent demonstrates exceptional efficacy in removing critical metals like cobalt, nickel, and copper, as well as reducing harmful metals such as mercury and manganese to undetectable concentrations. Unlike traditional lime-based treatments, PMAP’s reagent prevents gypsum formation and reduces waste volume significantly, improving reagent utilisation and solid waste handling. Furthermore, PMAP technology offers benefits beyond environmental stewardship. By reducing water treatment costs and improving resource management, it enhances operational efficiency and aligns with broader corporate sustainability goals. Additionally, PMAP expedites permitting processes by eliminating the need for traditional water treatment infrastructure and mitigating risks associated with hazardous reagent transportation. Integrating PMAP as a pre-treatment for existing lime facilities provides further benefits, including optimisation of treatment operations, reduced reagent consumption, and the recovery of valuable metals from generated sludges. Overall, PMAP represents a groundbreaking advancement in mining wastewater management, showcasing the transformative potential of AI and environmentally friendly solutions to foster sustainable and responsible mining practices globally. Its inaugural project in the Yukon Territory aims to demonstrate its capability to remove contaminants from mine water, paving the way for widespread adoption in the industry.

Sep 1, 2024

The role played by lawyers in business has, in the course of the last 15 to 20 years, changed perceptively. This development has coincided with, and indeed has been a reflection of, the changing nature of Australian business, especially as the mining industry established its predominance in the Australian economy. The nature and extent of governmental regulation of business, too, has changed markedly. As a consequence, there has been a qualitative'change in the nature of commercial law practice. For the needs of business to be met, lawyers have had to develop specialist skills in new areas. Furthermore, there has been the emergence of the "in-house" lawyer, who increasingly plays a primary rather than a subordinate role in corporate law practice. There is no evidence to suggest that this trend, which is by now so well established, will prove to be ephemeral. Instead, with all indications pointing towards even greater governmental regulation of business activities, the intimate role of the lawyer in business seems entrenched.

Jan 1, 1980

Most new engineers in the mining industry do not realise the importance of legal obligations. During investigations the first question you are asked is: Do you have any proof or evidence? The smallest detail in an underground notebook or a diary entry is able to be used as your proof and/or evidence. The importance of a paper trail is often undervalued and overlooked when you first enter the industry. As a new engineer, all too often your legal obligations, including your duty of care are not given enough consideration. Whose job is it to inform you of what your legal obligations are and when do they end? Everyone has legal obligations at every level of the industry, from graduate to mine manager. The level of these responsibilities varies depending on the position that you hold. When you first start in the industry you need to understand what your responsibilities are and how you are expected to discharge them, whether they are memos, databases or senior sign-offs, etc. In order to fulfil your obligations you must first discharge your own obligation, which in turn discharges those of your department and ultimately those of the mine. As a graduate engineer in the mining industry what I have learnt about my own legal obligations has come directly from my own experience, which will form the basis of this paper.

Jan 1, 2007

By R R. Lovel

In this paper, life cycle assessment methodology has been used to assess the variations in water use associated with different metal production and processing routes and provide insights into the value derived from water usage in the minerals sector. Using water consumption data derived from the literature it has been shown that the æcradle-to-gateÆ water consumption (or embodied water) for production of the various metals considered in the study ranged from 2.9 m3/t for steel up to 252 087 m3/t for gold. The results largely reflect the grade of the initial ore used to produce each metal, and can be approximated by the following equation:W = 167.7 G - 0.9039 where: W = embodied water (m3/t refined metal) G = grade of ore used to produce metal (per cent metal) The study showed that indirect water consumption in the metal production life cycle, in particular that due to electricity generation, can make a significant contribution to the embodied water value, eg aluminium production. When expressed in terms of m3/t ore, the results for all metals considered indicated that the embodied water is roughly, on average, three times the water consumption of the mining and concentration stage. It was also shown that the economic value per m3 of water consumed for the minerals industry exceeds that for the agricultural and industrial sectors, supporting the view that allocating water resources to the minerals industry has a strong underlying economic basis. Water reforms currently taking place in Australia aim to address issues such as competition for water access, reduced security of supply and increase in cost. Consequently the minerals industry, along with others, can be expected to come under increasing pressure to reduce fresh or raw water use and to integrate water use across sectors. While water recycling is an obvious candidate to help reduce water consumption in the minerals industry, issues such as water quality, among others, will influence the extent to which this can be achieved. In addition, wastewater volumes can be minimised using techniques such as pinch analysis to establish and use the minimum water requirement for the process. The use of dry or near-dry processing technologies, for which the demand for water is small or zero, may be a more radical solution to the water consumption problem; however, it is possible that the introduction of dry processing would bring with it a new set of problems, including dust.

Jan 1, 2006

By J Stipcevich, N Patel, J Faithful5, S Narendranathan, L Tatnell4

ENGIE, the current owner and operator of the Hazelwood Open Cut coalmine, are in the process of rehabilitating the mine site in preparation for mine closure. Bucket wheel excavators (dredgers) used during coal mining operations are in the process of being demolished, which involves the controlled felling of dredger components using explosives. With the mine located in close proximity to the Morwell township and other critical public infrastructure, it is crucial that the use of explosives and the possible implications for mine stability is well understood. The felling of Large Mining Equipment (LME) will apply an impact load immediately to the underlying coal benches with the adjacent coal batters potentially at risk also of adverse slope stability impacts. This paper presents the 3D stability modelling methods employed to successfully assess the potentially adverse stability implications associated with LME collapse.

Jun 21, 2022

By I KylmSkorpi, H Mansikkaviita

The traditional direct-heated drying process has been replaced by the steam drying process in non-ferrous metal smelters, where steam is available from waste heat boilers. Many recent projects have selected Kumera Steam Dryers in equipping a new production line or modifying an old production line. The industrial performance of the steam dryers has shown significant energy saving and emission reduction. The steam dryers have been operated at high availability and long maintenance interval. As the process principle of Kumera Steam Dryer is different from other equipment, the set-up for steam dryer plants is configured to fit the smelter site and operation conditions to achieve optimal performance. This article discusses the equipment involved in the steam drying process and their combination options.

Jan 1, 2008

By B Zhao

Gas and coal dust, as potential harmful elements (PHEs) produced during mining, are considered two serious threats to the safe mining and the health of miners because of its explosive and pathogenic properties. To solve this problem, compound reagents enhanced water spraying technology was used to control the gas and coal dust in excavation working face in this study, and spray testing platform and wind tunnel were used to investigated the suppression effect for gas and coal dust. In addition, sink test, and agglomeration experiments were also used to analyse its suppression mechanism. Testing results show that the dust reduction efficiencies of compound reagents enhanced water spraying technology for four different particle sizes were 80 per cent, 91.43 per cent, 94.74 per cent and 94.46 per cent, and improved by 14 per cent, 10.86 per cent, 8.42 per cent and 4.25 per cent compared to water spraying. Moreover, the gas suppression efficiency also can be increased more than 20 per cent. Sink test, and agglomeration experiments results show that compound reagent improves the spreading efficiency of the liquid on the surface of the coal by changing its wettability, and this process can not only slow down the desorption rate of gas by forming a water-sealing effect in the coal surface indicated, but also promote the agglomeration of fine-grained coal dust.

Oct 12, 2022

By E M. Gama, L Resende

The tailings are waste from mineral processing operations. The type of tailings of iron ore processing are classified into sandy tailings and mud. Already the overburden are showing significant levels of useful mineral. Both iron ore`s waste have in your composition phyllosilicates/clay that indicates the potential for use in niche markets as paving and cement. According to several studies, there are various technologies in bench and pilot levels that could be used on a large scale but there is not an economic environment, tax, regulatory and tax set. Many of these technologies are associated with the reuse of tailings and overburden in construction. All these factors influence for that so many initiatives remain in search formats and cannot advance to the new business format. There is no way to set goals of reuse of this waste, as already occurs in China, if there is not a fiscal, tax and economic structure to support such measures. The way to foster and ensure that reuse of tailings and overburden is an incentive for promoting a culture of circular economy that would allow the emergence of an ecosystem between the private, public and Government sectors with the objective of accelerating and subsidize the entire network of reuse of this waste. The closure of the mine could be the tool used to ensure and boost this ecosystem of reutilization to align it with the vocation of the area of the mining law. Following this model, the end of the mining activity could provide a financial return to the local population, a more effective environmental compensation and a reduction in costs related to the closure of the mine. In this study are shown how the Vale is working in the reuse of tailings and overburden.CITATION:Resende, L and Gama, E M, 2018. The challenges of the reuse of tailings and overburden, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 117–125 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By O Jones

Longstanding occupational health challenges of the underground hard-rock mining sector require both an analysis of historical data to assess evidence of linkages between the source of the problem and subsequent illnesses, as well as investigating the means by which health risks to workers can be eliminated or minimised. This paper refers briefly to a recently established National Health and Medical Research Council (NHMRC) sponsored Epidemiological Study into the incidence of Lung Cancer, contracted by mineworkers in Western Australia (WA) due to the inhalation of diesel exhaust fumes from 1996 to 2012. Thereafter it reviews current knowledge of the nature of the challenges facing those responsible for the health and wellbeing of underground hard-rock miners in WA, commencing with the recent categorisation of diesel exhaust as ‘Carcinogenic to Humans, Group 1’, by the World Health Organisation’s (WHO) International Agency for Research on Cancer (IARC). An attempt is also made to explore how the challenge has changed with the adoption of more advanced engine technologies, including the increased generation of ultra-fine volatile organic and other nucleates, submicron carbonaceous agglomerates and toxic gases.The compounding effect of using the mine decline access entry as both the primary ventilation intake and haulage-way is also discussed, as is the need to develop a more appropriate metric for regulating diesel engine emissions. Finally the paper refers to ongoing in-mine research pursued by the National Institute for Occupational Safety and Health (NIOSH) at its Diesel Laboratory in an underground limestone mine near Morgantown in the USA.CITATION:Jones, O, 2015. Diesel exhaust and the underground miner in Western Australia, in Proceedings The Australian Mine Ventilation Conference, pp 167–172 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Ryan CG, Both RA, Mernagh TP, Large RR, Hunns SR, Gemmell JB

The Hellyer and Mt. Chalmers deposits are mound-style volcanic-hosted massive sulphide (VHMS) deposits in Australia. Textural, petrographic and microthermometric investigations of fluid inclusions in the Hellyer stringer system indicate that Type I, primary, liquid-vapour inclusions are 10-15 pm in size, and yield homogenisation temperatures of 170-220¦C in early 2A veins, 165-322¦C in main-stage 2B veins and 190-256¦C in late-stage 2C veins. These data suggest a waxing and waning thermal history. However, the average salinity remained between 8-11 NaCl equiv. wt % in all Stage 2 veins. At Mt. Chalmers, Type I inclusions up to 20 ¦m are found in quartz from the mineralised zone, and these inclusions yielded homogenisation temperatures of 160-268¦C and salinities of 5-8 NaCl equiv. wt %. Laser Raman spectroscopic (LRS) analysis indicates the presence of CO2 (

Jan 1, 1995

The Myally Beds, Surprise Creek Beds and Mount Isa Group form the upper part of the Proterozoic Western succession of rocks in northwest Queensland. The latter two units are partly equivalent, and are important for their base metal content at Mount Isa and elsewhere. The arenaceous Myally Beds lie unconform- ably or disconformably below the Mount Isa Group and Surprise Creek Beds; they contain four mappable units which were deposited on a broad, shallow shelf washed by east-trending currents. Emergence of the Myally shelf initiated a series of parallel, possibly intra- cratonic, troughs to the east and west. In the east, the Surprise Creek Beds were deposited between the emergent shelf and base- ment rocks, and consist of a shelf and trough facies divisible into 7 and 10 units, respectively. Trough sediments are continuous north-south, and show turbidite character- istics; algal dolomite characterizes the shelf facies. To the west in the Mount Isa trough, an orthoquartzite facies, the Warrina Park Quartzite, defines the base of the Mount Isa Group. Hinge zones between the shelf and trough environments are marked by east-west facies changes, and provide a focus for later major north-south faulting. However, some penecon- temporaneous faulting near Mount Isa is best explained as complex post-depositional faulting of a disconformable sequence. Subsidence and deposition in the Mount Isa trough continued for a longer period than in the Surprise Creek trough, allowing accumulation of lead and zinc deposits in the upper half of the sequence. The Surprise Creek Beds appear equivalent to the lower half of the Mount Isa Group, and are probably not prospective for lead and zinc. Turquoise and possible other secondary copper minerals are widespread in the Warrina Park Quartzite and equivalents in the Surprise Creek Beds, and further investigation of these formations seems warranted.

Jan 1, 1974

By H J. J Boshoff, A J. Karrasch

Mine planners frequently face the challenge of mitigating the impact of climatic events on mining operations, such as floods and droughts. Specific water management infrastructure can be implemented to meet operational requirements in response to these events. However, the effect of flood protection, for instance, may reduce the resilience of the site to drought. The probability and duration of unfavourable climate sequences significantly influences the net present value (NPV) of implementing specific water management infrastructure.Good life-of-mine planning will consider the incremental development of the project, and provide staged development plans. Water management infrastructure and the timing of implementation are facets of this process.CITATION:Boshoff, H J J and Karrasch, A J, 2016. A decision-making framework for water supply and flood protection options in net present value terms, in Proceedings Life-of-Mine 2016 Conference , pp 196–199 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By J Franke, C Gonzalez

One of the regular tasks of geotechnical and mining engineers is the measurement and management of deformation in underground excavations. Although several methods are used to do so, the incumbent methodologies for monitoring deformation and ground support serviceability are limited to the use of visual observations or measurements at discrete points, resulting in a qualitative assessment only. The introduction of LiDAR technology allows a quantitative assessment across the entire excavation volume and its rock surface, by collecting a full three-dimensional image of the entirety of an excavation such as an underground drive, decline, or a tunnel. Comparisons between epochs of complete 3D data coverage allows for change detection over time that doesn’t feature otherwise typical omissions. The implementation of regular scanning has shown to be highly advantageous for mines with swelling or squeezing ground, but also at mines with rapid deformation. Despite the LiDAR potential, its adoption has been slow. A key reason for that is that working with point clouds is foreign to most geotechnical engineers. Point clouds have long been the realm of surveyors, but to fully adopt their use in geomechanics requires retraining, upskilling, and devotion by the individuals and the company. Sites are already stretched, so often there are insufficient resources to be applied to bringing the new technology into use. The solution to this hurdle is to partner with subject matter experts to achieve the desired high-quality outcomes without the commitment of time by geotechnical personnel. This paper presents a new solution of fully automated raw LiDAR point cloud data processing that not only enables geotechnical engineers to avoid having to learn unrelated skills by allowing for deformation monitoring without associated training or expertise, but it also provides instant reporting results as well as a sophisticated database with features otherwise not available. All data processing time and effort is completely replaced by an automated process which at the same time opens up the opportunity to monitor many more excavation volumes at a higher frequency than is possible with conventional tools and methodology.

Nov 29, 2022

By Li N, Grimsey E. J

A technique has been developed for the fast measurement of the liquidus temperature of molten salt systems. The method employs a type K thermocouple embedded within the centre of a copper cylinder. The cylinder is immersed into the molten salt bath and the resultant heating curve is recorded using a PC-based data logging system. Upon immersion of the cylinder into the bath, a layer of salt freezes from the melt onto the surface. When this layer remelts during heating, the shape of the heating curve exhibits a change. The onset of this change can be detected by numerical differentiation of the heating curve, and the temperature at the onset represents an estimate of the liquidus of the melt. This work describes the technique and its application to the measurement of liquidus temperatures of MgC12 - NaCl and BaC12 - NaCl salt mixtures, in addition to a number of solidus temperatures.

Jan 1, 1996