Search Documents

By Young DJ

Gold mineralisation at the Hamata prospect is related to a series of stacked pyrite and quartz-pyrite veins associated with a number of shears which strike N to NE and dip E. Mineralisation is contained entirely within the Morobe Granodiorite close to the intersection of the Upper Watut Fault and some younger NE to SW striking faults. The prospect was originally detected in 1987 by a regional stream sediment sampling programme. Subsequent mapping and sampling outlined an anomalous zone approximately 900m long by 300m wide. Drill testing has indicated a resource of 46Mt at 0.9 g/t Au.

Jan 1, 1991

By C D. Rose

A review and summary of the results of 120 coal sampling system bias tests is presented. This review supports new methodology using multivariate statistics currently being considered by ISO TC27 SC4. The current difficulties with ISO 13909-8 are explained and the logic behind the current new working draft is discussed in detail. Bias was detected in nearly 36 per cent of tests reviewed, suggesting that much improvement is needed in designing, maintaining and monitoring the performance of sampling systems in order to avoid sampling bias.CITATION:Rose, C D, 2012. Bias testing of mechanical sampling systems for coal - A review of test results and call for use of multivariate statistical analyses, in Proceedings Sampling 2012 , pp 185-192 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By R McCarthy, P Darvall

FerrAus Limited's Robertson Range and Davidson Creek iron ore projects are located on the far eastern margin of the Hamersley Province, approximately 100 km to the east of Newman, Western Australia. The deposits are primarily formed of bedded haematite-goethite-limonite mineralisation within the Marra Mamba Formation, comprising a total combined resource of 164 Mt at 58.6 per cent Fe. The deposits represent relatively new discoveries for the Hamersley Province. The potential for mineralisation at Robertson Range was identified by Rio Tinto Exploration in 2000, while Davidson Creek remained untested until 2007. One of the main reasons for this is that these deposits are almost exclusively concealed beneath Tertiary sediments and recent transported cover making them difficult targets for conventional, prospecting style exploration. Since commencing exploration in the project area, FerrAus has collected nearly 20 000 stations of gravity data within the Robertson Range and Davidson Creek project areas, with most of this data collected at a 50 100 m station spacing. Gravity has proven itself to be an effective technique at predicting the position of the target host stratigraphy and has been a key driver in the exploration for concealed iron ore deposits. However, there is not always a perfect correlation between the position of gravity anomalies and concealed ore. The response of deep haematite bodies may be masked by low-density cover rocks, while other dense lithologies may be the cause of gravity anomalies which appear similar to the Marra Mamba targets. Hence, effective use of the gravity data requires interpretation in a geologic context with an understanding of the capabilities and limitations of the technique.

Jan 1, 2009

High sulphur volcanic-hosted hydrothermal environments are favourable geological environments for gold mineralisation. Numerous world-class gold deposits including Pueblo Viejo (Dominican Republic), Goldfield (Nevada), EI Indio (Chile), and Wa

Jan 1, 1994

The key to the successful debt funding of a new mining project, whether in economically established or developing nations, is the submission of a comprehensive feasibility study. The feasibility study forms the basis from which the resource banker can construct financial models which govern the amount of available funds, the conditions which control the supply of such funds and the time period over which the loan may be repaid. The bank will wish to ensure that the feasibility study is the best representation and confirmation of reality possible because this model is the basis of the loan security package. Thus the study will be vigorously interrogated by independent experts in all its elements including the ore reserve, mineability, metallurgy, operating and capital cost profile, environmental factors and management.

Jan 1, 1995

By A Späth

Active explosion barriers are used to contain and suppress a methane gas and/or coal dust explosion propagation, including localised mine fires. Early research indicated that these active explosion barriers could be used on a mechanised cutting machine, making it the only technology that could suppress an explosion during its propagation phase at the cutting face. Thereby not only adding protection during mining operations but also reducing the development of toxic gases, fatal temperature increase and fatal overpressure build-up. During their evolution over the last two decades, further advantages of Active explosion barriers were proven in mine operations in countries such as South Africa and China. Characteristics such as effectivity, efficiency, mobility and space restrictions allow these systems to be used in various locations within a mine operation, including highwall operations. This improved technology contribution to safer coal mining was recognised by mine operators, workers and regulators. The Queensland’s Recognised Standard 21 (Resources Safety and Health Queensland (RSHQ), 2021) stipulated active explosion barriers as a technology to ensure the safety within their underground coalmines. The mobility and flexible implementation of the active explosion barriers allow a feasible and practical solution for all critical locations for explosion and fire management in an underground coalmine. The conformance to the Recognised Standard can be achieved all underground coal mining operations such as Bord and Pillar, and Longwall mining. This paper describes the conformance, implementation and use of Active explosion barriers for Longwall mining and development as well as Bord and Pillar mining in Queensland’s underground coalmines.

Oct 12, 2022

By Littlewood E

We offer these notes as a practical contribution. All the arguments we advance have been tested by practical experience.In its preparation we realised that our subject was one of such importance and covered so wide a field that, dealt with by one of us alone, it might easily have been too much for him, so we have endeavoured, by mutual criticism and advice and a pooling of ideas, to bring forward a few points that may be of advantage to members. If any of the paper is of benefit to mining on the "Golden Mile," or elsewhere, we shall feel amply repaid for our efforts.It is obvious to all that the longer the machine is working productively per shift the greater the return, to all concerned; the machine-man himself and the company. Furthermore, if a man commences a shift with a definite objective in view; for instance, to bore and fire a specific cut, which he recognizes will give him a good financial return, then that man will exercise all his capabilities to attain that objective.In this paper we hope to demonstrate the value to the machine-man of the knowledge of the capabilities of each hole he bores, so that he will be enabled to utilize his drilling time to the greatest advantage. Also, we hope to show that such drilling time can be advantageously extended.After the war, with the influx of new men to the industry, some education on the finer points of machine work may be desirable, and any instruction in this branch must stress the realization of the value of each hole.We realise that most of those present have a sound workable knowledge of machine-mining, and we are not trying to teach anyone the fundamentals of machine work, but we would like to bring to their attentIon some of the finer points which we believe are very important.The machine-man has control of gear of a capital value of over £150, and the use or misuse of that material has a direct bearing on working costs. Therefore it is imperative that the capital outlay is gainfully employed.A "bogger" in charge of a 5/- shovel engaged unproductively is bad enough. How much worse for £150 worth of gear to be not fully productive.Figs. 1 and 2 demonstrate angles of break, and the full realization of the importance of this angle is essential to our paper. Although these Sketches are two-dimensional, we hope they will be sufficient to demonstrate our meaning. We will pass over them as briefly as possible.Fig. 1 shows three holes asked to perform an identical task.(a) 7-ft. hole bored 2 ft. into solid ground-will not come out.(b) 4-ft. hole bored 1 ft. from solid ground-will come out easily.(c) 5-ft. hole bored to solid ground-the best that can be expected under general conditions encountered.The angle of break is a right-angle, normal to direction of hole.

Jan 1, 1944

By A Grace, C Sennersten, T Taylor, A Davie, R Lyu, D Pentecost, C A. Lindley, J Craig, L De Macedo Camargo

Many underground mine void spaces are not suitable for human entry due to unprotected roofs, instability or having an unknown safety state (eg if they are many decades old). Investigations of these voids may nevertheless be important for general mine safety, for example to detect propagating collapses or water accumulation, prevent accidental intrusion by new developments or drilling to reassess old spaces for re-mining. Robots are an ideal technology for investigating these spaces, especially flying, rotary-wing robots that can access and map vertical structures and spaces while avoiding rocks, water and mud that have accumulated on void floors. To operate in underground mines, we are developing customised unmanned aerial vehicles (UAVs) as well as interactive 3D virtual models of the vehicles and their underground environments for controlling vehicle operation and visualising incrementally gathered survey data. Using a game/simulation engine to provide an interactive interface for UAV operation makes it possible to orchestrate external spatial information and video feeds with in-game cameras for optimal visualisation that is not limited to the position, orientation or field of view of cameras mounted on the UAV. First and third-person points of view with respect to the UAV are provided, together with 2D and 3D gaze tracking to provide effective interfaces for geology and mine engineering experts without the need for specialist UAV piloting skills. Ongoing work is addressing the provision of greater levels of autonomy for these vehicles to support mapping well beyond the line of sight of operators and geological characterisation of rock surfaces using sensors mounted on them, including miniature X-ray fluorescence and Raman spectrometers. Gathered data is fed into more general 3D models of the mine, block models and orebody so that the UAVs function as elements of a mobile perceptual system for intelligent mining.CITATION:Sennersten, C, Lindley, C A, Davie, A, Lyu, R, Grace, A, Evans, B, Pentecost, D, Taylor, T, De Macedo Camargo, L, Craig, J, Salomao, G N, Hellicar, A, Biggins, D, Timms, G, Coombe, M, Shahriar, M S, Smith, G and Rahman, A, 2015. Unmanned aerial robots for remotely operated and autonomous surveying in inaccessible underground mine voids, in Proceedings Third International Future Mining Conference, pp 101–108 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

Blasthole cone samples are used for grade control in most of the iron ore mines of the Pilbara of Western Australia. This method of sampling is straightforward when the target sampling interval matches the mining bench height but is problematic when the blasted bench is 'flitch' mined in two or more passes. Crucially, the sampler needs to decide which part of the blast cone represents the upper and lower flitches to be mined. This sampling selection decision is usually made by assuming a certain proportion represents the subdrill component of a sampling face in a blasthole cone and the two flitches are split equally from the remaining portion. In this study of a West Australian channel iron deposit, sampling experiments were carried out to determine the actual proportions of a sampling face in a blasthole cone by spray painting the blast cones at flitch and subdrill boundaries during the drilling process. Measurements were then taken to assess the differences between assumed sampling face proportions and actual proportions. A set of paired samples was also collected from a number of blastholes with one set using the assumed proportions of each flitch for each sample, while the other set sampled the actual proportions, which were identified from the cone painting process.

Mar 1, 2010

Alternatively are they a necessary evil'? Exploration geologists are a much higher profile group but then again the higher they are the bigger they Bill. At a mine site they are reluctantly being accepted as equals by mining engineers given the requirements of the `Code' in the reporting of Ore Reserves. How best can mining geologists service their customers? Are more revealing questions to be answered in who are their customers? In the past mining geologists lived isolated existences pouring over plans and sections, now with user-friendly software packages available and the use of LAN, mining geologists and mining engineers talk electronically - God forhid what the future might hying - they might even talk to accountants and metallurgists!

Jan 1, 1997

By D Wimpenny

The Bogong Power Development Project in Victoria, Australia involved the construction of a 15 m long mass concrete plug up to 9 m in diameter within the head race tunnel. The plug is critical to theperformance of the scheme as it permanently seals the head race tunnel under approximately 300 m head of water.The location of the plug in the headrace tunnel was determined by a programme of in situ rock stress testing using both hydrofracturing and over coring stress testing methods.In recognition of the importance of the plug, the Head Contract specification requires that its temperature during hydration be controlled using an embedded cooling system. In addition, contact grouting and curtain grouting around the plug cannot commence until thermal contraction was substantially complete.This paper describes the use of bespoke fi nite element software to model the temperature rise in the plug and design mitigation measures to control temperature rise in the plug. These measures include restricting the concrete placing temperature to 10°C, incorporating 39 per cent fly ash in the concrete and installing embedded cooling circuits.Site trials were undertaken to calibrate the model for the proposed concrete mix. The cooling system comprised 25 mm ID pipes forming twelve separate circuits that fed 7°C water from a single chiller unit. The cooling system reduced the peak temperature in the plug to approximately 30°C and the associated risk of early-cracking. The time before contact grouting could commence was shortened to less than two weeks from casting.

Mar 8, 2011

By E Amini, N Beaton

Application of ore pre-treatment technologies such as Grade Engineering and in-pit ore treatment require comprehensive analysis to show proven value is being generated by switching away from the current practices. Considering most mining operations last several decades; the pre-treatment technologies must be investigated over life of mine (LOM) to truly show value was generated or lost. Therefore, a value chain flowsheet model has been usually developed to run those analysis/simulations over LOM using a set of defined ore characteristics and the operating equipment capacities. The Integrated Extraction Simulator (IES) has been used for this type of LOM simulations as it has the necessary flexibility to accommodate the whole mining value chain flowsheet in one platform and provide essential computation power to run mass simulations for the given scenarios using the resource block model. This allows to forecast the value chain response over the LOM for all given scenarios in a feasible amount of time. The traditionally developed flowsheets for the analysis/simulations are usually limited to the mineral processing plant and were developed based on a single audit conducted on the plant in a very short time, e.g. several hours. The process plant is being operated with a certain ore at a certain condition during the short audits which would not reveal the true capacity of the operation equipment when ore characteristics changes. Therefore, it would be impossible to define the true capacity of the equipment and identify the constraints along the value chain. In this study, a methodology was developed to identify the constraints along the value chain and implement those in the IES flowsheet using process information. Also, the equipment models were fine-tuned to represent the true capacity of the equipment in the flowsheet using the same data set. The methodology was tested over five process plant in two operations and showed the performance forecast was significantly improved over the traditional methods being used so far. Then those high-fidelity flowsheets were used to evaluate the ore pre-treatment technologies proposed by the relevant resource company experts.

Nov 10, 2020

By G M. Tranell, M Tangstad

The CO2 footprints in the production of Mn-ferroalloys and silicon/ferrosilicon are correlated with the fossil carbon consumption. The CO2 emissions may be reduced in the Mn-ferroalloy process by increasing the degree of prereduction and reduction of carbonate materials, while the silicon/ferrosilicon process is optimised based on silicon yield. By changing the fossil reductant into biogenic reductants, the global warming potential will be decreased even more. Even if the reductants are biogenic reductants, there will still be a global warming potential (GWP) in eg the electrode consumption and the CH4 emissions in the charcoal production. To reduce the use of fossil reductants there are also more disruptive technologies like the use of H2 that at least for the silicon production is on a very low technology readiness level (TRL). Using metallothermic processes will reduce the use of carbon but requires carbon neutral metal reductants. Electrowinning can have low CO2 emissions, and the electrowinning of pure Mn is a technology of high TRL. Salt and oxide electrolysis is under investigation for both Mn and Si production however the research is still on a low TRL. The use of CCS/CCU (carbon capture storage/utilisation) is a part of obtaining carbon neutral processes. Last, the energy mix used for these energy demanding processes is discussed.

Aug 21, 2024

The importance of the accurate determination and interpretation of the bulk density and porosity of a given iron ore deposit is very often disregarded or neglected. Large amounts of time and money are spent on delineating and testing orebodies, and yet one of the most important factors in resource evaluation is sometimes estimated or, at best, determined from existing data from similar deposits. The Thabazimbi and Sishen South iron ore deposits are two well-known economical occurrences of high-grade iron ore in South Africa. Both these deposits formed as secondary enrichment of banded iron formation lithologies. Ongoing density studies on both these deposits are underway and results thus far proved very effective and necessary. Small-scale methods are used to determine average values for different ore types on both deposits. These values are used in resource estimation and geophysical interpretation.

Jan 1, 2007

By A Melloy, D Holt, M Jurak

Oaky North is AustraliaÆs highest producing underground coal mine. In 2011, the mine produced 8.7 Mt of high-quality coking coal. The high quantities are a result of the constant strive for optimising the operating time of major production units, which involves investing numerous resources, including diesel equipment, in supporting and maintaining their operation.In July 2011 it was identified that the diesel particulate matter (DPM) levels in the underground workings were above acceptable levels, due to the high level of diesel activity. Over the next 12 months, several controls were implemented to reduce exposure to personnel: the main ventilation system was upgraded; the production forecast was adjusted to better manage the diesel fleet, removing surges in diesel usage; and an electronic diesel tag board was introduced to centrally manage the distribution of diesel usage around the mine.From the start of the campaign in emission reduction, an intense DPM monitoring regime was established. Within a few months of the introduction of the centralised tag board, there was a major reduction in emission levels. After the installation and commissioning of the new main fans, the emission levels dropped further, such that over-exposures are now a rarity.Oaky North continues to explore new systems to better utilise their diesel fleet while still maintaining control over DPM emissions.CITATION:Melloy, A, Holt, D and Jurak, M, 2013. Reduction in diesel particulate matter at Oaky North, in Proceedings The Australian Mine Ventilation Conference , pp 187-190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By I Canbulat, J Oh, A Mcquillan, D Payne

This paper presents a new risk assessment tool for coal mine excavated slopes. This new empirical-statistical Slope Stability Assessment Methodology (SSAM) is intended for use by geotechnical engineers at both the design review and operational stages of a mine’s life to categorise the risk of an excavated coal mine slope. A likelihood of failure is determined using a new slope stability classification system for excavated coal mine slopes developed using a database of 119 intact and failed case studies sourced from open cut coal mines in Australia. Consequence of failure is based on slope height and stand-off distance at the toe of the excavated slope. Results are presented in a new risk matrix, with slope risk being divided into low, medium and high categories. The SSAM is put forward as a new risk assessment tool to assess the potential for, and consequence of, excavated coal mine slope failure. Unlike existing classification systems, assumptions about the likely failure mode or mechanism are not required. Instead, the SSAM applies an approach which compares the conditions present within the excavated slope face, with the known past performance of slopes with similar geotechnical and geometrical conditions, to estimate the slope’s propensity for failure. The SSAM is novel in that it considers the depositional history of strata in an excavated slope and how this sequence affects slope stability. It is further novel in that it does not require explicit measurements of intact rock, rock mass and/or defect strength to rapidly calculate a slope’s likelihood of failure and overall risk. Ratings can be determined entirely from visual observations of the excavated slope face. The new SSAM is designed to be used in conjunction with existing slope stability assessment tools. CITATION:Mcquillan, A, Canbulat, I, Payne, D and Oh, J, 2018. New risk assessment method for coal mine excavated slopes, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 473–495 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By H Khoshrou, A Siamaki

Blast designs can have productive and non-productive impacts on downstream stages, mine productivity and operating costs. On the other hand, ground vibration, fragmentation, and back break caused by blasting impose damage and financial penalties and which must be controlled by blast design. One of the significant variables in blast design is the burden. In this study, the potentials of artificial neural network are investigated in prediction of burden in the Sungun copper open-pit mine. Input data were assembled through 18 blasting blocks according to different levels and experimental geomechanical investigation. To construct the model blastability index, uniaxial compression strength, hole diameter, specific weight of rock, rock quality designation and cohesion strength are taken as input parameters, whereas, burden is considered as an output parameter. Mean square error was used as the performance function and back propagation algorithm as the training function, containing four hidden layers and 14 data sets. Four sets of data were used to make sure that correct training had been carried out. This produced the coefficient correlation of 0.662.

Sep 26, 2011

By M Hawkins

The Clem Jones Tunnel (formally known as the North-South Bypass Tunnel), a A$2.88 billion road tunnel project in Brisbane, Queensland, was successfully completed almost seven months ahead of schedule. The project included two parallel 4.7 km long road tunnels, 740 m of intermediate roadway access ramps and two auxiliary ventilation tunnels. The tunnels incorporate intelligent tunnel systems, best practice fire and life safety standards and typical civil tunnel elements.Over the duration of the project the Parsons Brinckerhoff (PB) and AECOM (formally Maunsell) design joint venture (MPB) were Lead Designers to the Leighton Contractors and Baulderstone Bilfinger Berger Joint Venture (LBBJV). Construction of the toll road commenced in September 2006 and was completed in March 2010, with the tunnel opening then. Contributing to the success of this project was the continued support the lead designers gave throughout the construction period.This paper will focus on some of the structural elements that contributed to the success of the project – in particular the cable tunnel structure, a small precast, culvert shaped element under the pavement of the mainline tunnel, and the fit-out of the Gibbon Street shaft which were designed to be constructed in a combination of precast and in situ concrete.The cable tunnel was incorporated early in the design phase and runs the length of much of the tunnel. This paper will outline the challenges faced by the designers with implementing this system which provided significant construction advantages, among which were being able to install a separate ventilation duct during construction and to start fitting out the mechanical and electrical conduits and drainage system while tunnelling was still underway.The Gibbon Street shaft had a length and width of 20 m by 40 m and an overall depth of 38 m. A 20 m high structure of precast and in situ concrete was constructed in the base to accommodate mechanical and electrical equipment and provide a take-off access for the southern ventilation tunnel. The construction purpose for this structure was to provide a junction between the tunnel boring machine (TBM) and the roadheader-style tunnels, a staging platform for commencing the roadheader tunnelling, and a platform where the TBMs could be dismantled and removed.The design was assessed and reviewed many times throughout the construction process to address the needs of each of these stages. Innovative use of precast concrete was used to minimise construction time.Additionally, the designers provided support to the construction team from the time of design completion through to the tunnel opening. This meant that the changes to the design and adjustment of construction loadings could also be assessed. The fi nal outcome resulted in an efficient construction sequence and a project that has provided an excellent outcome for the client, stakeholders and community.

Mar 8, 2011

By M Bellamy

The DeGrussa copper deposit was discovered by Sandfire Resources in April 2009. Construction of the 1.6 Mt/a concentrator, open pit and underground mining operations commenced in March 2011 with first concentrate production achieved in October 2012. Over the next ten years, DeGrussa grew to include both the DeGrussa and Monty underground mines, establishing itself as one of the world’s premier copper producers with total production of 663 000 t of contained copper by the time the mine closed. Final ore was trucked from Degrussa on 5 October 2022. This paper examines the mine closure experience from both a planning and operational perspective. The paper provides an overview of the site’s mine planning process including the factors involved in determining the end of the mine life and how this was tracked and communicated in the lead up to the end of mining operations. It will also look at some of the specific operational aspects involved in maintaining steady state production all the way through to the last day while facing increasingly challenging conditions. These factors, along with the external factors faced by most of the industry such as labour shortages and COVID related disruptions, contributed to making it an interesting journey to the end of operations at DeGrussa.

Mar 29, 2023

By V Louchnikov

Ever increasing depth of mineral extraction presents a challenging environment for hard rock underground mines. High in situ stresses and associated seismicity with potential rock burst hazards are the major decisive factors contributing to the choice of a ground support regime. Conventional ground support systems, designed primarily for static loads, are not always capable of providing safe working conditions for underground personnel in seismically active mines. Systems specifically developed to resist dynamic loading and allowing for larger deformations are therefore preferred alternatives. High-tensile chain-link mesh has a proven record of successful use in open cut operations in various rockfall barrier installations due to its high energy absorption capacity. It has also been used in underground operations in various parts of the world. Its application in Australian underground mining, however, is limited due to the high labour intensity. This paper describes a method of mechanised installation of a chain-link mesh as trialled at Golden Grove, a base metals underground mine in Western Australia. A purpose-built mechanised roll mesh handler, developed in Australia, was used in this trial. The handler is compatible with all standard multi-boom underground drill rigs and is operated utilising the hydraulic circuit normally used for the feed arrangement.A number of operational benefits have been identified during the trial, the main two being:•improved safety of underground personnel due to the reduced amount of manual handling, and•increased productivity due to the decreased cycle time (the trial suggests a 40 - 50 per cent reduction in time over the weld mesh installation method).Although the energy-absorbing mesh combined with yielding rock bolts is a ground support system of choice for rock burst prone conditions, the operational upsides recognised during the trial imply that this product can also be competitively used in less demanding ground conditions where customarily weld mesh or shotcrete are used as a primary surface support.

Mar 21, 2011