Search Documents

By M E. Watson

Minimising dilution and ore loss is an important part of ensuring profitability of a gold mining operation. White Foil open pit gold deposit is a low-grade deposit and therefore managing ore quality is a high priority. Ground movement through blasting can displace ore and waste boundaries up to 10 m from their in situ location and therefore requires stringent ore movement monitoring and adjustment. There are currently only two options for monitoring blast movement – utilising visual targets (commonly lengths of polypipe) but this has widely been replaced by electronic blast movement monitors (or BMM). Regardless of the technology used, the basic principle is to compare the pre- and post-blast locations of the targets to determine the movement of the rock mass during blasting, which is then used to determine the final location of ore and waste boundaries.The Blast Movement Technologies (BMT) BMM system has been used at White Foil since June 2014. The system has been effective and reliable during that time; however, the annual cost of using the BMM system is greater than other monitoring alternatives. As such, the open pit geology team conducted a study comparing the BMM system against the conventional polypipe technique. The objective was to quantify the profit and loss that would occur based on the ore block transformations from both methods. Eight blasts were selected where polypipes were installed in additional holes adjacent to the BMM monitoring holes. The resulting movement vectors from the respective methods were used to create post-blast ore blocks by transforming the in situ ore blocks. While polypipe is a cheaper alternative, the BMM system tracks ore and waste boundaries more effectively resulting in better quality control, enhanced ability to minimise dilution and ore loss thus maximising profit. For these eight blasts, it is calculated that the BMM system resulted in A$664 978 extra profit through a reduction of ore loss. The total cost of a yearly BMM package was recovered in the first two blasts of this study. The primary reason for the difference is that polypipe had a poor recovery rate of 32 per cent compared with 92 per cent for BMM at White Foil. Therefore, the data used to transform the ore blocks was less representative, resulting in inaccurate post-blast ore block boundaries when using polypipe.CITATION:Watson, M E, 2017. Blast movement monitors or polypipe? A study into cost-effective blast movement monitoring at White Foil gold mine, Western Australia, in Proceedings Tenth International Mining Geology Conference 2017, pp 433–440 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By J Karlovšek

Civil engineering infrastructures are often subjected to different types of natural and mechanical activities. These influences may result in serviceability or even in stability of structures due to material deformations, increased water content within the materials used or the formation of internal or adjacent cavities that may threaten the infrastructure. Construction practices can lead to development of such defects in the form of cavities. In civil engineering it is crucial to detect these variations in material properties and to detect the presence of defects. However, as they are often hidden from view, these attributes may be difficult or impossible to target with traditional testing methods. For these reasons rapid geophysical methods, such as ground penetrating radar (GPR), are increasingly being used. At the University of Queensland (UQ) GPR is used for detection of voids and cavities which have been caused by an over excavation of the earth pressure balance machine (EPB) operating in a closed mode.A variety of numerical simulations using the finite-difference time-domain (FDTD) methods and preliminary experiments have been carried out in order to specify information about the nature, type, size, location and other characteristics of targets to be detected by GPR. In doing this the difficulty of interpreting GPR data, which is mainly due to the complexity of the factors involved in multiple possible solutions of the observed features, can be overcome.

Mar 8, 2011

In the current climate, there is a real need to bridge the gap between theory and the real world mining considerations, and develop viable, cost-effective, high performance thickeners. With a greater need to extract profits from both difficult-to-process ores and lower grade orebodies, coupled with the necessity to produce 'greener', less water intensive technologies, suppliers need to take current thickener designs to the next level and into the 21st century. The complexity of 'getting it right' within a thickenerÆs feedwell, the 'nerve centre' of the thickener, is no small task. Delivering dilution water and mixing this water with incoming feed slurry, addition of flocculant, maximising flocculant-slurry interaction to build aggregate size, minimising unabsorbed flocculant percentage, volume average of solids volume fraction, momentum dissipation ratio, dilution recycle ratio, volume average shear, maximum shear rate at exit, aggregate size on exit, uniform discharge profile and more ù all of these need to occur in the right order and in the right proportions within the feedwell. This paper discusses the genesis and evolution of a new feedwell design, the first major innovation in the thickening industry in over 15 years.

Jan 1, 2008

By Ring R. J, Waters D. J, Vautier F. E, Fulton E. J

Laboratory leach tests have been carried out by the Australian Atomic Energy Commission to compare the effectiveness of Caro's acid (permonosulphuric acid) as an alternative oxidant to pyrolusite in the leaching of uranium ores. Results demonstrated that Caro's acid reduced acid consumption in leaching and the lime required for neutralisation of tailings liquor. The uranium extraction was unaffected by choice of oxidant.Following this study, Interox Chemicals Pty Ltd arranged a plant trial using Caro's acid at the Nabarlek uranium mill of Queensland Mines Ltd. The trial confirmed that significant savings in acid and lime usage can be achieved under plant conditions.Plant operations also demonstrated that Caro's acid has a number of significant operating advantages over pyrolusite.Queensland Mines Ltd have recently decided to convert their leaching process from pyrolusite to Caro's acid. The new system is expected to be fully operational by mid 1983.

Jan 1, 1983

The demands of the economy require larger manufacturing facilities using greater quantit- ies of raw materials which must be mined, handl- ed, stockpiled and recovered with efficiency and dependability. All over the world, mining com- panies, steel manufacturers, power stations and process plants are not only seeking but finding methods of increasing outputs and'reducing costs in the field of materials handling. In mining bigger continuous mining machines and shovels, larger trucks and crushers are digging and processing greater quantities of differing materials which have to be handled and shipped at rates once thought to be impossible. To implement such schemes demands the blending of a lot of diverse-equipment, mining machinery, bins, feeders, reclaimers and it is here that the belt conveyor assumes a role of ever increas- ing importance. Significant developments have taken place in the seventies with respect to conveyor belt transportation; not only in the systems but also in the components which combine to make such systems work efficiently.

Jan 1, 1976

By McDonough RJ

Mechanical agitation is the preferred system for Carbon-in-Pulp processes. Agitator design requires an understanding of the relationships between energy, shear and flow and the nature of shear rates and shear stress distribution in an agitated tank. Laser techniques are useful when studying these phenomena. The alternatives are open impeller agitation or draft tube circulation. Each has advantages and disadvantages but both require careful choice of impeller and system geometry. Overall the draft tube circulator is the more attractive in many cases. Open impeller agitators are designed in accordance with established procedures for mineral slurries taking due account of shear effects in tanks containing carbon. Preferred tank proportions are 1:1. Circulator design methods were developed in the alumina industry before being applied to CIP processes. Optimum draft tube diameter is critical to power requirements. The overall system must be designed as an axial flow pump operating in a closed circuit. Such a system exhibits quite characteristic behaviour which requires an impeller of varying pitch angle and aerofoil section for best stability and efficiency.' Tank height may be 2 or more times diameter. Resuspension of settled solids can be assisted by a series of slots in the draft tube. These slots have the secondary effect of stabilizing hydraulic behaviour and reducing installed power requirements.

Jan 1, 1982

By Jaczkowski B

The lower orebody (LOB) at Chingola Divi- sion of Nchanga Consolidated Copper Mines Limited (NCCM) accounts for approximately 30 per cent of the total copper production for the company. The uniformity of the geology of the orebody lends itself readily to a computer based ore reserve calculation and accounting system. The mining units are physically defined such that a hierarchical type of com- puter file organisation can reflect the existing physical interdependencies. In 1972, a project team consisting of one representative from each of the mine planning, operational research, and computer services departments was formed to investigate and to define the technical mining requirements of the dynamic ore reserve system (DORS). The system was finally implemented in 1975ò

Jan 1, 1977

By M Jones, G Corder, A C. Keith

"Sustainable development has become an issue of ever increasing importance to the mining industry. The Ernst & Young (EY) mining industry risk radar regularly shows several sustainability elements in the top ten risks, with social license the number three risk in the 2014/15 survey. This is supported by the Fraser Institute survey results of 2013 showing that 36 per cent of responding companies indicated public opposition had affected their permitting and approvals process.Addressing these issues in a strategic way across a mining business that is then translatable to actions at operational level has remained an elusive goal in the industry. In addition the environment and community issues are commonly viewed as somewhat separate from financial and production issues and as a compliance cost rather than a value add. In their Harvard Business Review paper of 2011, ‘Creating Shared Value’, Porter and Kramer outline changes in thinking required for companies to improve their business sustainably through considering the societal issues impacted by their operations and products. Along the lines of ‘doing more with less’ companies’ value chains can be redefined to reduce energy, transport, water or other resource usage leaving additional resource for societal usage and/or reducing environmental impacts. This paper explores the linking of the holistic Five Capitals-based approach with the creating shared value (CSV) concept to help businesses unleash the benefits of innovation. Previous papers have demonstrated the potential for Five Capitals approach to create strategic value through sustainable development. Building on previous work, this paper provides an overview of the current status of holistic approaches to mine management and presents the application of the CSV concept on an African mine currently undertaking capitals-based strategic planning. The paper also demonstrates the value that has been created through utilising this approach and proposes improvements for changing the way the industry tackles and delivers benefits related to sustainability issues.CITATION:Keith, A C, Corder, G and Jones, M, 2016. Strategic sustainable development – creating shared value in the mining industry, in Proceedings International Mine Management Conference, pp 249-264 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 22, 2016

By Lynch K. S, Street R. P

Hamersley Iron's pellet plant at Dampier involves ore drying, dry grind- ing in ball mills, disc balling and, indurating by use of the straight grate system. After five years of operation, the plant's output has been increased from the design capacity level of 2 M.T.P.Y. to 2.5 M.T.P.Y. Steps taken in equipment modifica- tion, improvements in process control, and changes in maintenance procedures are described.

Jan 1, 1973

By A Halim

The European Union (EU) have recently issued new Threshold Limit Value-Time Weighted Average (TLV-TWA) for diesel exhaust contaminants, which are CO, NO2 and DPM. The new limits for CO and NO2 were issued in 2017 whilst the one for DPM was issued in 2019. However, in order to allow EU mines to formulate strategies to comply with these new limits, the EU granted a transition period in which mines could use the old limits until the new limits are enforced. The new limit for CO and NO2 will be enforced from 21 August 2023 whilst the one for DPM will be enforced from 21 February 2026. The new limit for NO2 and DPM is very low, 0.5 ppm for NO2 and 0.05 mg/m3 of Elemental Carbon (EC) for DPM. Combination of these two limits would be the lowest among all mining jurisdictions worldwide. It poses a huge compliance challenge to EU mines if they keep using diesel machines. Therefore, a study and a field trial were carried out by the author in 2019–2021 to investigate whether replacing diesel machines with Battery Electric Vehicles (BEVs) would be the best answer to this challenge. This paper outlines results of this study and field trial.

Oct 12, 2022

By P Bartsch

Uranium solvent extraction, USX has been applied commercially for recovery and concentration for over 50 years. Uranium in acidic liquor, which is prepared following ore leaching, solid/liquid separation and clarification, can be treated through a sequence of operations; extraction-scrubbing-stripping, to obtain purified liquor. USX has dominated the primary uranium industry as the preferred technological route to converter grade yellowcake. The practices of design and operation of USX facilities has found renewed interest as new mines are developed following decades of industry dormancy. This article seeks to outline principles of design and operation from the practitioner’s perspective. The discussion also reviews historical developments of USX applications and highlights recent innovations. This review is hoped to provide guidance for technical personnel who wish to learn more about good practices that leads to reliable USX performance.

Aug 8, 2011

By T Purvis, J Calverd, A-K Greve

The Ernest Henry Mining (EHM) underground mine is situated adjacent to the Great Artesian Basin in North Queensland and within a fracture zone. Underground development commenced in February 2008 and has extended to approximately 1000 vertical metres below the surface.Groundwater has been encountered in numerous locations throughout the mine, predominantly on the eastern side of the orebody and often related to fault structures. Most of the groundwater encountered has been managed with conventional pumping systems; however, on occasions large water inflows have been encountered, which have had a significant impact on the planned development of the mine. Some of the intersections encountered had the potential to compromise the mine from a combination of high temperature (over 45°C), high pressure (3500 kPa) and high flows (50–100 L/s).This paper describes three case studies where significant water inflows were encountered and then controlled by the injection of cementitious grout into the rock mass. The case studies are the 1650 mid-shaft heading, the 1325 shaft access decline and the 1625 to 1475 fresh air rise (FAR) raise bore. Each case study includes a brief description of the event that occurred and the grouting equipment and techniques developed to enable mining to continue.The paper also describes the development of a hydrogeological map of the mine, the probe-hole regime used for high-risk headings and the required processes and systems to inject both cementitious grouts and polyurethane resin into the rock mass.CITATION:Purvis, T, Calverd, J and Greve, A-K, 2014. Management of high-pressure groundwater in underground development at Ernest Henry Mine, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 217–226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By N Herault

PT Freeport Indonesia recently completed preproduction development and construction of the Big Gossan underground copper and gold mine, located in the Ertsberg mining district of Papua, Indonesia. Production has commenced with an expected ramp-up to full production of 7000 tonnes per day in 2012. The Big Gossan utilises an open stoping mine method with paste backfill.In order to deliver ore to the mill, which sits in a valley above the ore deposit, an underground production shaft and hoisting facility was designed and constructed as the key component of ore haulage. The design and construction of the Big Gossan shaft posed many challenges to the project team. Available shaft design and construction expertise were limited as this was the first shaft of its kind in Indonesia and the project was undertaken during a time of high industry demand for new shaft systems. Construction resources were also limited due to the remote location and competition with existing, producing mines for these resources and skills. The project also taxed the ability of Freeport to provide services and resources to this as well as their other projects.Completion of the Big Gossan shaft was a milestone in PT Freeport Indonesia’s plan to fully transition ore production to the underground environment in this decade.This paper deals with the various challenges faced by PT Freeport Indonesia and shaft contractor, PT Redpath Indonesia, during the construction of the Big Gossan shaft and offers suggestions to improve future shaft projects of a similar nature.

Mar 21, 2011

Sampling of CIL/CIP circuits is typically done by compositing samples of feed and tails over eight or 12 hour periods. As the residence time in the leaching tankage may be approximately 20 hours, the tails from any period being derived from material entering the circuit 20 hours earlier do not correspond to the head from the same sampling period. Moreover, mixing in the series of tanks in a circuit also modifies correspondence between input and output. A special purpose simulator has therefore been developed to allow for the mixing and delay in the tankage and permit estimation of the head assays corresponding to any tailings sample. Thus more accurate assessment of the day-to-day recoveries of gold and silver follows. The model, programmed in Excel, assumes that the tanks are perfect mixers. By inputting the sequential head grades and considering that no leaching has occurred, the head grade which corresponded to the tailings for each period could be estimated. Allowance is made for variations in feed rate over the sampling period by computing the average flow rate of slurry and thus the residence time of each increment of the tailings. This simple model and its application have been found to be subject to some limitations, which are discussed in the paper, resulting in some unresolved variability in results. However, for a typical circuit even the simple model was able to greatly improve consistency of recovery data with variations being approximately halved by eliminating much of the anomalous variation arising from the lack of correspondence between head and tail when changes in head grade are occurring. Therefore, this permits genuine variations in metallurgy to be identified with greater confidence and thus operational shortcomings can be identified and addressed more quickly.

Jan 1, 2006

This paper presents a rationale for selecting appropriate support elements which combine to form a support system to maintain stability in mines subjected to both strainburst and the shaking that occurs from fault slip. The overall approach was developed during the 'case for safety' study undertaken to allow the then Beaconsfield Gold mine (now Tasmania mine) to resume development and production after the 25 April 2006 ground-fall and fatality that received worldwide publicity. Issues of the sometimes competing requirements of support element performance during dynamic loading are discussed and the need for support flexibility is contrasted with the usual high support element stiffness required when these are used to reinforce rock masses. An example is presented to show the steps and technical details required to design each component of a support system to counter the de-stabilising effects of seismicity.

Nov 25, 2010

Supergene nickel sulphide ore mined currently by Agnew Mining Company is at times partially oxidised to sulphate. The resulting soluble nickel, and calcium and magnesium in mill water, are shown to act as depressants in flotation. The depressant effect is favourably selective in that violarite, the main nickel mineral, is less affected than pyrrhotite. Nickel recovery, however, is adversely affected, probably through reduced flotation of complex sulphides. Soda ash consumption is increased markedly by the presence of the cations as shown by operating data and pulp titration tests. A significant increase in concentrate grade, from 9% to 14% Ni, was achieved late in 1981. One of the changes in plant practice which contributed to this improvement was the addition of soda ash to mill feed rather than to flotation feed as before. It is shown by laboratory tests that this reduced the depressant effects of the cations, thereby improving recovery at the expense of rougher selectivity, or equivalently, increasing concentrate grade at constant recovery. The selective depressant effect cannot be exploited until scavenger recovery is improved and a scavenger concentrate regrind-retreat äcircuit is implemented. Development is

Jan 1, 1978

By E Asakpo, S Chaffer, A Heath

Newmont has had continuous production at their Ahafo operations, Ghana, since 2006. In 2013, Ahafo initiated an efficiency programme to improve mill performance and reduce energy consumption. Following this assessment, a Turbo Pulp Lifter (TPLTM) was installed in the Ahafo SAG mill in April 2015 to replace the existing radial pulp lifters. Plant operational data showed delivery of a power saving of 10 per cent, an improvement in throughput of 3.3 per cent, with no loss of grind size. Pulp lifter life was also doubled from 11 to 22 months.However, during subsequent relines when the grates were removed it was found that one in four of the outer pulp lifters were wearing at a faster rate than the remainder. This was investigated by Discrete Element Method (DEM) modelling, which predicted some overtopping and internal recycle within the pulp lifter. Significantly, the model predicted that the recycled material would pass back down every fourth outer pulp lifter, matching the field observations. Subsequently, the DEM investigation was continued and became an R&D project to improve the TPL design. The results are summarised here, leading to the development of the next generation Spiral TPLTM.CITATION:Heath, A, Chaffer, S and Asakpo, E, 2018. The development of optimised pulp lifter design for the Ahafo SAG mill using discrete element method modelling, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 585–594 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Kasaneva S

The San Cristobal gold district is located 110 km east of the port of Antofagasta, Chile. It contains the San Cristobal gold mine, where Niugini Mining Ltd. commenced a heap leach operation, with initial reserves of 10.1 million tonnes grading 1.34 g/t An, in December, 1990. The San Cristobal district occurs within an upper Cretaceous-lower Tertiary magmatic arc. The main mineralisation occurs within a northwest trending subvertical zone, 1km long and 70-100 m wide, which contains rhyolite porphyry and minor breccia, and is locally termed the "subvolcanic complex". At the San Cristobal mine, most gold mineralisation occurs in subvertical quartz-pyrite veins which were emplaced in dilational sections of an imbricate fault system. The bulk gold resource comprises four ore shoots which formed where the vein system intersects the subvolcanic complex. Gold-bearing quartz-pyrite veins also occur at separate prospects, the Three Sisters and Sol prospects, west and south of the San Cristobal mine. Hydrothermal alteration consists of potassic and propylitic assemblages related to intrusion of the subvolcanic complex. This alteration is overprinted by a phyllic stage which is associated with the emplacement of the quartz-pyrite veins. The oxide zone is 180 m thick, and contains native gold, electrum, limonite, and manganocarbonates. The underlying hypogene zone contains pyrite with minor chalcopyrite, sphalerite, galena, covellite, bornite, chalcocite, and arsenopyrite. Fluid inclusion studies indicate that the deposit formed at approximately 270¦ C, and the mean salinity of the fluid was 4% NaCl equivalent. These observations enable the San Cristobal deposit to be classed as a porphyry-related, mesothermal quartz-vein system of the low sulphidation type.

Jan 1, 1995

By S Kost, R Nievergelt, F Cortes

In recent years, the use of steel fibre-reinforced concrete (SFRC) for segmental tunnel linings has become increasingly popular due to numerous advantages including durability, resistance to spalling, reduced cracking at corners and edges and significant cost-saving potential. One of the key parameters for measuring the performance of SFRC is the residual (post crack) flexural strength. A problem often faced in design and quality control of SFRC is the high variability of results obtained by standard beam test methods, with reported coefficients of variability (CoV) in the order of 25 per cent. The high test variability results in a relatively low permissible design strength relative to the average flexural strength of the material and commonly leads to non-conformances with respect to residual flexural strength during production testing.This paper presents the implementation of an alternative testing method using large round determinate panels (RDPs) for quality control testing of the SFRC used in the segmental lining of the City East Cable Tunnel (CECT) in Sydney. The alternative RDP test method was found to correlate well with standard beam tests and significantly reduce the variability of test results, minimising the risk of outlying residual flexural strength results, with zero non-compliant test results reported during the production period.This successful implementation of an alternative test for post-crack flexural strength with lower variability in results constitutes a relevant precedent to demonstrate the feasibility of this approach which contributes to the development of more cost-effective concrete mixes and minimises the risk for non-compliant results and the contractual disputes that commonly arise from these.CITATION:Cortes, F, Nievergelt, R and Kost, S, 2014. Development of a segmental lining specification for steel fibre reinforced concrete flexural strength testing using round panel tests, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 461–468 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By H J. J Boshoff

Mine closure planning integrated into life-of-mine (LOM) planning during the operational phase consists of many subcategories. One of these subcategories that needs to be fully integrated into the LOM planning is that of water management planning. Issues arise when mine water management infrastructure, which is required post-mine closure, is only considered closer to the end of LOM. Once the mine is closed monitoring is focused on water quality as an indicator of closure performance, hence inadequate upfront post-mining water management planning or integration into operations will result in environmental harm. The lack of considering post-mining water management is not uncommon in LOM planning. Poor mine site water management and planning are a wide reaching problem for the mining industry. Numerous active mines have been issued with environmental notices and penalties for contaminated water discharge; including issues with abandoned mines now being cared for by governments all over the world.Mitigating sources of water contamination caused by existing and closed mine sites that are leaching pollutants might be impractical, due to inaccessibility to the contaminants or final landform topography. The opportunity to consider and introduce post-closure required mine water management infrastructure is lost once the waste facilities are constructed. Mitigating contamination is made more problematic with mines located in remote areas, serviced by dedicated roads, water supply, electrical supply, etc. It is expected that these services will be decommissioned or drastically reduced, once closure is reached making remedial work much harder. Inadequate planning, to ensure access and easily maintainable water management infrastructure, could lead to erosion and contamination going unnoticed. There are numerous examples of poor mine water management practices in Africa, Asia, Australia, South and North America. In the United States more than 23 000 km of streams are affected by pollution sourced from some 50 000 abandoned or mature mine sites (DeGraff, 2007).CITATION:Boshoff, H J J, ?2014. Inadequate water management planning resulting in long-term closure liabilities, in Proceedings Life-of-Mine 2014 , pp 233–246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014