Search Documents

By H Jones

Closure cost estimates may be generated at any stage of a mining operationÆs life; commencing with the initial prefeasibility studies and continuing through to the final decommissioning cost estimates. However, not all mine closure cost estimates are necessarily the same. Cost estimates will vary depending on the purpose for which they are prepared, the organisations requiring or undertaking the estimate and the stage of the mining operation. Different organisations can legitimately arrive at disparate cost estimates for closing the same mine because the organisations have different reasons for requiring the estimates. Another, equally valid, reason for potentially wide variations in cost estimates by different organisations on the same mine site is the different definitions of æclosure costsÆ used by different estimators. This paper considers the different approaches by different organisations including operating companies, government authorities and financial organisations and uses a hypothetical example based on practical experience to illustrate some of these differences in estimation methods.The paper suggest that a more consistent approach to closure cost estimating in the Australian mining industry would assist mining companies, governments, the accounting industry and the broader community to better understand this complex component of mine planning. One possible approach to closure cost estimating is briefly outlined.CITATION:Jones, H, 2012. Closure cost estimation - All things to all men?, in Proceedings International Mine Management 2012, pp 115-124 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By J Benn, V Kuznetsov, G Timms, A Spain

Earthen covers are now widely used in the mining industry to control the generation rate and/or release rate of low quality drainage from piles of sulfidic minewastes. Covers are usually designed to reduce the water infiltration rate and in some cases may also reduce the oxygen flux to the underlying sulfides. Engineered covers have only been used since the 1980s, however, and there is very little field data on their performance in the longer term. This lack of information has implications for the degree of confidence that can be placed on the predictions of the environmental impacts of sulfidic minewastes, for the acceptance of close-out criteria by regulatory authorities and for the financial liability of the mining industry. Covers were placed on sulfidic waste rock dumps at the abandoned Rum Jungle uranium mine during 1984 - 1985. These covers were designed to reduce the water infiltration to less than five per cent of incident rainfall by both water shedding and storage-release mechanisms. Regular monitoring by the Australian Nuclear Science and Technology Organisation (ANSTO) demonstrated that the covers performed better than the design criterion for around ten years, but infiltration rates have subsequently increased. There is a 66 per cent probability that the infiltration rate now exceeds five per cent of incident rainfall. The cover on the largest pile, WhiteÆs heap, was sampled in pits dug at eight locations. Sampling was carried out at the end of the monsoonal wet season and again at the end of the ædryÆ season. This, together with laboratory testing, enabled cover performance to be assessed against five criteria: design, construction, cover material characteristics, physico-chemical characteristics and biological characteristics. We are of the opinion that the design of the cover was suitable to achieve the objectives of stability, water shedding, storage-release, and provision of a substrate for vegetation growth. Over most of the surface of the heap, the construction of the covers, drains and erosion prevention structures was in accordance with design specifications. However, several small and localised bare patches on the upper surface of WhiteÆs heap coincide with a reduced cover thickness, which is likely to have been due to poor construction in those patches. The construction of covers on minewastes is dependent on an adequate source of material meeting design specifications. From our limited examination, it appears that there was shortage of material for each of the three zones û a lower impervious clay layer, the moisture storage-release layer and the upper erosion-resistant layer for vegetative growth. An indication of this was that the upper layers in some areas were observed to be thinner than specified. We are of the opinion that this shortage of suitable material has been responsible for some of the changes observed ten years after emplacement. Physical and geotechnical testing indicated that the cover materials no longer meet the original specifications. In particular, the permeability at the 8 locations was found to be greater than specified, by up to several orders of magnitude. The higher permeability may explain the higher observed rainfall infiltration and moisture content of the waste rock. This increased permeability appears to be due to a combination of biological and physical processes û galleries formed by termites and ants and an extensive system of shrinkage/desiccation cracks formed by the development of a polygonal blocky structure involving the entire lower clay layer. The desiccation cracks may fill with coarser illuviated materials and form a conduit through which roots access the underlying waste rock. Measurements were made of oxygen flux into the heap as cover layers were excavated in the pits. They indicated that the full cover currently reduces the oxygen flux to 20 - 23 per cent of that into bare waste and that this reduction seems to be proportional to the cover thickness. It was also found that the oxygen flux into the cover is about four times higher at the end of the dry season than at the end of the wet season and that the difference is due primarily to the difference in moisture content of the cover. Recommendations are made for the design and construction of covers.

Jan 1, 2003

By L Lorenzen

The selection of samples for metallurgical test work is generally focused on providing geologically representative samples. One of the major problems experienced with metallurgical test work using drill hole data, is the small sample sets selected for metallurgical testing. Major process and financial decisions are being made from results obtained using snapshot samples. Snapshot samples means that samples are basically selected only by grade and spatial location with the assumption that the rest of the orebody or portion of orebody is similar and will respond metallurgically the same way – ie the assumption is that the mineralogy and lithology are basically the same as the test sample. From the test work, algorithms were usually developed and used to describe throughput and recovery using some explanatory variables including grade (mineral chemistry) and ore hardness. These algorithms were then used in the recovery models to determine tonnes produced and plant throughput. However, the metallurgical parameters are a function of many geological factors including grade, lithology, alteration, mineralogy, spatial relationships and SG. In previous years, the limited mineralogical information available was deemed enough for the metallurgist to make decisions as to how many samples are needed to evaluate the metallurgical performance of the ore during processing, and subsequently the basis for the plant design. If the orebody is consistent and not complex or refractory (thus, relative simple lithology), then only spatial and grade samples will be needed to evaluate the throughput and recovery, so limited mineralogical information may be acceptable. There is now, however, an increasing realisation that the mineralogy and geology change, as do the metallurgical characteristics of the orebody, so limited samples may not be sufficient for effective metallurgical test work.It is the purpose of this paper to discuss the effect correct mineralogical information has on the subsequent metallurgical test work program and process selection using a case study. Factors such as type of rock, rainfall and topography are thought to influence the minerals that ultimately form in various orebodies, with the result that different orebodies often react differently during metallurgical test work programs. It is therefore important to obtain accurate mineralogical and elemental deportment data, which will also indicate where the valuable metal containing minerals are located within the orebody. The better you plan and execute your metallurgical test work program during the early phases, the more accurate the decision-making process will be during the selection phase. Improved integration between geology and metallurgy data gathering (geometallurgy) during early phases will result in more accurate predictions with regard to throughput and recovery during modelling and process. Equipment selection will be considerably simpler in later phases with early planning, with improved mine and process scheduling and subsequent net present value (NPV).

Sep 5, 2011

By M Freeman

In a visionary move, the Planning Commission and the Ministry for Planning in Western Australia decided to invite three extractive industry quarry operators, local government councils and State Government departments (Minerals and Energy, Environmental Protection, South West Development Commission) to contribute jointly to study the impacts of blasting on areas surrounding basalt quarries in the Bunbury region of WA. The results of the study will help establish suitable zones in which land uses will be controlled under a proposed Greater Bunbury Region Scheme and in local planning schemes, to minimise conflicting land uses. This paper discusses the blasting program conducted to characterise and model the vibration behaviour of the rock under the effects of pilot-scale and full production blasting, and highlights some of the benefits achievable when a thorough blasting impact program and assessment is conducted at the planning stages of land-use establishment.

Jan 1, 2001

The homologous series of saturated fatty acids investigated in this study generally show a steady gradation of properties with chain length. The solution pKa values were assumed constant at 4.9, however reported pKa values could be lower or higher. Hematite flotation response and surface pressure for aqueous solutions of these fatty acids were measured as a function of pH. For the shorter chain fatty acids, the undissociated acid was shown to be the predominant surface active species with flotation, supplemented by the physical adsorption of acid anions as the chain length increased. The reduced solubility of the longer fatty acid carbon chains made these reagents ineffective as flotation agents. The maximum flotation response of hematite using tetradecanoic acid corresponded with the precipitation edge of the reagent. The results show that the values of surface pressure of the surfactants are not always a good indication of their effectiveness as flotation collectors.

Jan 1, 2005

By Siwiec A

The laboratory investigations which are necessary to evaluate the mineral processing effectiveness usually include density separation of narrow size fraction of the feed and one of the products. In each size - density fractions the content of valuable mineral has to be determined. These data and yield in each size - density fraction can be specified by a matrix of partition coefficients. They are counterparts of recoveries. These coefficients can be compared with the mean recoveries at each density or size fraction or the total recovery, to determine which density - size fractions are processed in the best or worst way. The basic categories are: vector of metal content l _i 1711, 7t2, òòò, ltM I ò vector of particle size distribution x = I d1, d2, ..., dN I ò matrix of partition coefficients P11, P12, Pi N P _ P21, P22, ..., P2 N PM1 PM2..., PMN These three conceptions allow one to determine all the basic metallurgical parameters of a mineral processing unit. Losses of valuable mineral are connected with: ò mineralogical composition of the ore (types of minerals, their properties, dissemination, crystallochemical affinity, type and properties of gangue minerals), ò applied technology and technical equipment (beneficiation as a stochastic process, processing methods, process control, intergrowth liberation, water quality). Examples of application of the analytical method proposed are given for zinc - lead and coal processing plants.

Jan 1, 1993

A great part of the research on froth flotation of gold ores deals with ores containing gold associated mainly with sulphides, resulting in a largely accepted view that what takes place with sulphides (eg pyrite) in a flotation cell also happens to gold particles. This paper is concerned with the influence of some inorganics (CuSO4, CaO and NaCN) on gold particles flotation, using ethyl or amyl xanthates as collectors. The bench-scale tests were carried out with ground quartz and gold particles mixtures. Some findings stemmed from this study: flotation of the gold particles of size 0.16 mm was efficient adding only frother; larger gold grains were better recovered by the use of stronger collector CuSO4 did not seem to be an activator for gold; the addition of NaCN up to 200 g/t or CaO up to 2000 g/t did not depress the gold grains when amyl xanthate was used as collector although with ethyl xanthate the gold depression was verified.

Jan 1, 1993

By X L. Liu, W Huang, J M. Zhu, S L. Wu

The shape, position and thickness of the cohesive zone have a great influence on the operational performance of the blast furnace. Many researchers have found that the high temperature properties of iron ores determine the formation of the cohesive zone. The results of this work show that sinter of high basicity interacts with lump ores and acid pellets due to the difference in chemical compositions. The softening and melting properties and the primary slag formation behaviours in the cohesive zone are improved by the high temperature interactions. The high temperature interaction is mainly influenced by the chemical compositions, porosity, interfaces and so on. Although the softening and melting properties and primary slag formation behaviours of lump ore A (a typical limonite lump ore from Australia) is the poorest of the iron ores studied, the high temperature properties of integrated burden A (consisting of sinter and lump ore A) is no worse than the other integrated burdens due to the high interaction between the sinter and lump ore A. It is useful to apply the results in the optimisation of blast furnace burden.CITATION:Liu, X L, Wu, S L, Huang, W and Zhu, J M, 2015. High temperature interactivity of iron ores in the cohesive zone of the blast furnace, in Proceedings Iron Ore 2015, pp 363–366 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Best R, Poulos H

This paper discusses the results of an Australian Coal Association Research Program project into the development of a routine analytical design method for roof support in underground mines. Simple design tools have been developed using a combination of elastic solutions, free body diagrams, and pile theory. An approach to the design of roof support in layered strata based on the ability of bolts to resist shear stresses is outlined. It is shown that pre-tensioning and angled installation are effective ways of increasing the effectiveness of bolts in such a situation. In highly stressed strata, macroscopic failure is predicted and a design based on the support of surcharged rock wedges is proposed. The methods are applicable to both coal and metalliferous mines.

Jan 1, 1995

By P J. McCarthy

Globalisation and consolidation is resulting in the mining industry coming to be dominated by a small number of very large companies seeking to lever assets and knowledge to create wealth. As an important service provider to the mining industry, the minerals tertiary education sector needs to understand these global drivers and respond to them. However, it is under-resourced and its sustainability is under challenge in all Western countries. Through the establishment and funding of the Minerals Tertiary Education Council (MTEC), the Minerals Council of Australia (MCA) has provided a unique opportunity to build a national, world-class minerals tertiary education environment in Australia that can be sustained in the long-term. This paper reviews how the global changes occurring in the mining industry provide the model for what needs to occur in the minerals education sector and how MTEC is the logical vehicle to facilitate these changes. It concludes by suggesting that the time has come to integrate the minerals tertiary education providers into one business. Furthermore, the vision should be for a global mining education academy based around a virtual university capable of servicing the cultural diversity and continuing education needs of the global minerals industry.

Jan 1, 2001

By T Ireland, S Eratne, W Newns, P Spies

The approach to risk management during the procurement of major projects often has a significant outcome on the ultimate delivery of a project. The NZ$1.4 B Waterview Connection project is the largest and most complex project yet undertaken by the New Zealand Transport Agency (NZTA) and the procurement process for an alliance contract was refined to provide compliance with the International Tunnel Insurance Group (ITIG) Code of Practice for Risk Management of Tunnel Works (TCoP). The principle of shared risk within an alliance incentivises a common understanding of project risks prior to finalising the alliance agreement and therefore enables superior risk management through design, construction and beyond. Risk management practices need to be instigated well in advance of commercial phases, so that commercial competition does not lead to a significant elevation of project risk. In particular the practice of gaining commercial advantage by taking on a potentially unmanageable level of risk is one of the outcomes to be avoided by the TCoP.During the procurement phase the NZTA placed high value on design and construction mitigation measures proposed in order to address ground risks, as is appropriate for a major tunnel project. In order to achieve alignment on the level of geotechnical risks an Alliance Geotechnical Baseline Report (AGBR) process was developed.This paper describes the measures taken during the procurement process to achieve certainty with respect to outcomes and minimise project risks whilst also achieving value for money. Refinements to the procurement process to ensure compliance with the TCoP prepared by the International Tunnel Insurance Group (ITIG) are described along with the AGBR process applied as part of a suite of measures to achieve a successful procurement outcome.CITATION:Ireland, T, Spies, P, Eratne, S and Newns, W, 2014. Risk management and use of a geotechnical baseline report for a competitive alliance procurement?process, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 553–562 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By B Mennie, R Poedjono, G Coad

PT Freeport Indonesia operates a large copper and gold mining operation near Tembagapura, Papua (formerly, Irian Jaya), Indonesia. This is a remote location with its own set of unique operational characteristics. The mining and concentrating operations typically produce a concentrate containing 2500 tpd of copper and 6000 oz of gold per day from the combined mining of a 45 000 tpd (ore) block cave operation (DOZ Mine) and a 190 000 tpd (ore) open pit mining operation (Grasberg Open Pit). The Grasberg Open Pit mine will be exhausted in 2015 at which time FreeportÆs operations will entirely underground mining methods. The Common Infrastructure Project (CIP) incorporates the elements required for the shift to underground mining at a production rate approaching 200 000 tpd. The AB Adit portion of the CIP will provide deep level access to the Grasberg Block Cave (below the Open Pit), Kucing Liar, Big Gossan, and the Mill Level Zone orebodies. Commencement of the project was September 2003. The Grasberg Block Cave is planned to start production in 2014. This paper provides details on the project scope, innovative contractual framework, advancement of mining methods throughout the life of the operation, equipment selection, manpower selection, training, geological, and socio-political conditions related to the project.

Jan 1, 2005

By A B. Bayooke, A C. Robertson

In terms of underground tunnelling in metres advance per capita, Australasia compares well with the best world performers. This is because of the large number of metalliferous mines, coalmines and civil tunnelling projects, with the Australian tunnel advance for civil and mining projects exceeding 625?km/a. In terms of hard rock quarry extraction, Australia produces approximately 200?Mt/a of aggregates, roadbase, fill material and specialist rock products from its quarries, which equates to approximately 8?t/capita. Australian mining and tunnelling contractors are also of world standard and are used to excavating in a variable range of ground conditions in a competitive environment. One author has been involved in tunnel and underground space planning and quarrying in Australia for the past 25 years and predicts that, over the next 20 years, there will be a major swing towards underground space for commercial uses. This paper identifies the potential uses of underground commercial excavation and the planning and geotechnical challenges for the future. Underground quarrying creates new opportunities to extend existing quarries within their urban footprint with minimum impact on the surrounding community. Investigations by the authors reveal that there are very few cities in the world that actually incorporate underground space planning in their city plans. However, cities such as Helsinki have been planned in detail to utilise the rock resources beneath them. Brisbane is used as a case study for a practical application of commercial underground space and underground quarrying in Australia.CITATION:Bayooke, A B and Robertson, A C, 2014. Geotechnical challenges for underground commercial space and quarrying in Australia, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 317–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By B Vorster, T Medhurst, A Huey

Roof conditions at Oaky North Mine can be prone to stress related damage and/or time dependent degradation. The ability to identify these areas prior to mining has proved challenging using traditional methods. To help alleviate this situation, a study was initiated to investigate methods for roof characterisation using geophysical logs. This involved the use of neutron log data to provide an indirect measure of the proportion of carbonaceous/micaceous laminae present in the immediate roof strata. Detailed analysis of the shale–porosity inter-relationships arising from this analysis provided a means to estimate the proportion of laminations for a given roof interval. This paper outlines the process and how it was used to improve the current GSR modelling and hazard mapping process.

Nov 29, 2022

By P W. Wypych, D Curry, A P. Grima

The market has become highly competitive for engineering and equipment vendors, who are challenged to reduce costs while improving efficiency and productivity of mine operations through plant improvements and expansions. Although conveyor transfer systems account for a small percentage of the infrastructure cost of a mine, they form an integral part of the process supply chain. Malfunctions or suboptimal performance can result in substantial financial cost from delayed start-up, unscheduled downtime, reduced throughput and increased maintenance costs.Discrete element modelling (DEM) is a powerful simulation method used to virtually prototype and test the performance of transfer equipment throughout a design cycle. When developed and applied correctly, DEM can provide insight into performance that exceeds the traditional analytical methods, especially when dealing with complex ore properties, behaviour and/or situations.Using case studies sourced from the authors’ recent research and industrial project work, this paper will address the industry goal to increase efficiency and productivity as well as the methods available to the engineers responsible for delivering designs that meet the aims of this strategic approach.The main focus of the paper will be the new calibration technology, which has been developed by the authors to generate DEM material models that are linked to real-world properties and flow behaviours via unique dynamic testing and innovative parameter calibration methods. These calibrated DEM material models can be deployed by engineers into their existing workflows, whether it be for feasibility studies, concept or final design, plant troubleshooting or optimisation.This new technology allows engineers to gain greater insight than that provided by traditional approaches to the design of transfer chutes and other process equipment and also allows informed design decisions to be made that meet industry efficiency and productivity requirements.CITATION:Grima, A P, Curry, D and Wypych, P W, 2015. New discrete element modelling calibration technology to facilitate the increased efficiency of ore handling and processing operations, in Proceedings Iron Ore 2015, pp 449–464 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By H W. Scriba

The development and improvement of computer-based process simulation packages over the past 20 years has provided process engineers with a powerful tool to use in the design of complex metallurgical plants. The use of such modelling tools has enabled the design of process plants that minimise operating and capital costs whilst optimising plant efficiency and recovery. Almost every new project developed in the current market is underpinned by a simulation of the process. In line with engineering best practice this simulation should be based on laboratory/pilot plant test work results and sound assumptions. Any errors that are not identified in the development of the process simulation may have significant effects on the final design and operation of the processing plant. Developing a simulation of the process in a comprehensive, logical and auditable manner is thus essential in ensuring the simulation accurately represents the expected process plant behaviour. A methodology that ensures these requirements are met has been developed by SNC-Lavalin Australia and is described in this paper. The methodology includes the major review stages of data collection, model planning, model building and optimisation, model review, scenario testing and options development, and model reporting. All of these stages should incorporate comprehensive client interaction and review by a suitably qualified representative. In applying these methodologies SNC-Lavalin Australia ensures that the process simulation model developed can be confidently utilised in the design of the process plant, and in the estimation of operating and capital costs, whilst ensuring that engineering best practices are met.

Jan 1, 2008

About 90 per cent of the pre-mining BIF-hosted iron ore resource of the Hamersley Province of Western Australia is of the Phanerozoic supergene martite-goethite type. The remaining ten per cent formed as supergene deposits at ~2000 ¦ 200 Ma, and were later modified by burial to form the Proterozoic martite-microplaty hematite ores. The supergene-metamorphic segment of this general unified model has been challenged by three recently published hypogene-based genetic models for the hematite ores, all requiring meteoric oxidation to produce the ore. The most recent and detailed, by Taylor et al (2001), is based on data from the small Southern Batter and North deposits of the Mount Tom Price mine. The authors proposed that during Stage 1 æoverpressured bicarbonate-saturated basin brines from the dolomite aquifer of the Wittenoom FormationÆ at 150 - 250¦C, dissolved free silica from BIF to produce a stratigraphically thinned, magnetite-carbonate-silicate-apatite rock. In Stage 2, meteoric oxidation of siderite to secondary microplaty hematite + ankerite, and magnetite to martite, at unspecified elevated temperatures and pressures, was followed by carbonate leaching (Stage 3). Finally, during Stage 4, weathering with removal of apatite, produced the typical low-phosphorus, porous martite-microplaty hematite ores of the Tom Price-Whaleback type. However, evidence of both microplaty hematite and martite reduced to magnetite, and of infill silica, apatite, and ferroan chlorite, with late-stage pyrite, in the pore space of martite-microplaty hematite ore, shows that the hydrothermal activity at Mount Tom Price is a post-ore event. Neither pyrite nor ferroan chlorite could resist the oxidation required to form hematite ore. Recrystallisation of microplaty hematite in these infilled zones to a typically coarser form than present in most of the normal ores, is a further supporting factor. A more credible, post-ore alternative to the hypogene genetic model is suggested here. Re-exposure to leaching by ground water of the metamorphosed ore deposits in the Phanerozoic resulted in the partial removal of remnant goethite. Localised modifications in the porous BIF/ore contact zones were driven by exothermic oxygen/pyrite/carbon reactions in the footwall Mt McRae Shale. Cool descending oxygenated meteoric water in the permeable ore horizons, acted as one limb of a thermal convective cell. In the other limb, heated reducing solutions rose through the permeable contact zones, to produce the observed localised modifications of BIF and ore. Expelled silica from the carbonatised BIF invaded adjacent porous ore to form erratic silicified ore zones, and to produce the local quartz vein systems found in the associated overlying BIF.

Jan 1, 2002

By J Vann

Geometallurgy is inherently multidisciplinary and it gains its power to deliver improved outcomes for the minerals industry by bridging silos between disciplines. This cross-disciplinary approach unlocks value, identifies (and avoids) value destruction and provides a pathway to better implementation of an energy efficient and sustainable minerals industry. Despite this promise, we argue that the cross disciplinary approach also represents the greatest threat to the success of geometallurgy. Some key cross disciplinary issues identified are:Geometallurgy has so far evolved in the technical sphere, mainly by collaborations of geologists and metallurgists. Consequently, in many cases the business dimensions and value have not been incorporated. Financial and risk evaluation viewpoints need to be assimilated into the geometallurgical paradigm. In fact, until such measures are integrated into practices, the value cannot be fully demonstrated.The historical and current efforts on geometallurgy have been highly focused on improved sampling and measurement of geometallurgical properties or appropriate proxies. This work has been driven by professional and academic geologists and metallurgical engineers. It is notable that mining engineers (who are critical in the value delivery of geometallurgy through changed planning approaches) have so far been at the margins, or absent. The construction of valid three dimensional (3D) geometallurgical models raises some important organisational, mathematical and geostatistical considerations. The enhancement of resource models to account for geometallurgical aspects must be managed carefully if the full value of geometallurgical thinking is to be realised.The use of 3D geometallurgical models to change business decision making and practices is the real nub of the problem. We believe sophisticated scenario based evaluation methods are required if the potential impacts of spatial rock properties on processes further down the mining value chain are to be realistically evaluated. Such changed practices require ‘whole of value chain thinking’ to embed this change into the business in an ongoing way.Because profitable geometallurgy demands changed approaches to business decision-making and also organisation of the firm (radically changed in some cases), the senior executive viewpoint must be incorporated into the language and thinking of geometallurgy. This is unavoidable if the establishment of a geometallurgical approach to project evaluation, development and operation is to be successful and sustained.A powerful analogy for the problem faced by geometallurgy is the transformation of safety culture in the mining industry in the past 20 years. We argue that, as in the safety revolution, explicit models, cultural change and management of the ‘soft’ dimensions of the problem are pivotal to success of geometallurgy. In light of this, we propose a model (‘the Geomet Curve’) that gives a framework and pathway for geometallurgy in seven steps. The implications of this model for technical and organisational steps required at different stages are discussed.

Sep 5, 2011

Avoca Resources LimitedÆs Higginsville Gold Project has a resource base of over 1 300 000 oz of gold. The Trident underground mine, which forms the basis of the project development, has a resource base of 927 000 oz of gold. Avoca is building the Higginsville Gold Project based on a minimum ten year vision, producing over 150 000 oz per annum. The project development has taken less than three years from the Trident discovery hole in October 2004 to the first ore production in June 2007. This paper discusses the background work associated with the development of the Trident underground mine in a difficult period for new project development in Western Australia. The resources boom, led by the iron ore industry in the Western Australian Pilbara region, is creating cost pressures and, combined with a lack of people and equipment, is placing cost and timing stress on a small developing project. Avoca Resources has developed a project execution management strategy aimed at mitigating cost blow outs and schedule delays.

Jan 1, 2008

By S Lakemond, L I. Ku, J Vaughan

Conventional processing of poly-metallic gold containing flotation concentrates are challenging for a number of reasons. One reason is that substantial copper and zinc in the cyanide leach solution compete with gold and silver for carbon adsorption sites. In this study, metal-cyanide adsorption kinetics and equilibrium are measured on three samples of coconut derived activated carbon and one sample of synthetic carbon. Loading selectivity was confirmed to be in the order gold>silver>copper>zinc for all carbon samples. The synthetic carbon tested showed promising results in terms of loading kinetics and capacity for precious metals.CITATION:Lakemond, S, Ku, L I and Vaughan, J, 2013. Effect of carbon type on adsorption of Cu, Zn, Ag and Au from mixed cyanide solution, in Proceedings World Gold 2013 , pp 411-418 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013