Search Documents

The pilot scale testing of Australian coals for their NO, emissions was carried out at the ACTC to investigate the influence of coal properties, furnace conditions and different NO,, control strategies on NO,, emissions. The NOx emissions for the Australian coals tested were found to vary over a wide range and primarily depended on combustion temperature and excess oxygen conditions. These coals did not exhibit any fundamental difference in NOx levels to other world coals. Under similar combustion conditions, the conversion of coal nitrogen to NO. was found to be best correlated with coal rank parameter, R, max per centage. The use of staged combustion as a control strategy was shown to reduce their NOx levels by 56 - 77 per cent.

Jan 1, 1991

As partition curves are widely employed to characterize screening efficiency which, by definition, should include a time parameter, it is shown, perhaps for the first time, that time is already included in the partition curves and how. Laboratory and plant results are used to show how screening efficiency depends on feed composition, near-mesh and oversize material and screen motion, and how these factors may combine to give an erroneous result that two identically efficient screens are different and two screens of different efficiency are identical. Reasons are given which show why a renewed interest in screening would benefit not only screen engineers and operators but also those concerned in formulating standard specifications of screen analysis methods.

Jan 1, 1984

By M Pyle, R Ch, T Vizcarra, ramohan, G Lane, G Ballantyne

Preconcentration, through gravity separation (Wallace et al, 2015), magnetic separation and particle size (Clout, 2013), has been used in many historical projects to convert low grade material into ore. More recently, pre-concentration technologies such as bulk sorting (Kurth, 2017), screening (Bearman, 2014) and coarse particle flotation (Vollert et al, 2019) have also demonstrated their ability to progressively reject waste through the value chain. These technologies can not only deliver stepchange improvements to the economics of mining operations, but can transform the environmental and social aspects by minimising water and energy consumption and significantly reduce the quantity of fine tailings produced. However, implementing progressive waste rejection requires technologies and approaches to be combined and applied in the right way to capture the value. From a technical perspective, progressive waste rejection introduces challenges related to the orebody, equipment performance, engineering and understanding the value chain from the resource through to final product. From a management perspective, the key issues are related to people and processes, in particular; motivating the business, challenging the paradigms, and introducing new ways of operating within the constraint of existing management structures to manage risks and minimise lost opportunity costs. This combination of technical and management issues means that progressive waste rejection is a complex undertaking for mining companies, yet the reward for the business and other stakeholders is potentially high and should not be ignored. This paper presents how progressive waste rejection can offer step-change improvements to the business case for high and low grade greenfield and brownfield projects based on case studies completed by Ausenco. The paper then outlines different implementation approaches from concept studies to execution to address the various technical and management challenges outlined above.

Nov 10, 2020

By A Minchinton

With blasting, all far-field phenomena including, but not limited to, stress wave propagation, fracture, vibration and muck pile formation are intrinsically and irrevocably dependent upon near-field phenomena or mechanisms that we describe using physics-based mathematics typically transcribed into computer codes. The energetics involved in such near- to far-field transitions are not fundamentally relevant as they are simply progenitors of these processes.The notion of explosive energy as a descriptor for explosive or blasting performance is a case in point. These energies, which are generally used in blasting tables, are almost exclusively based on ideal detonation theory alone and do not include the influence of the rock, charge diameter, blasthole length and the late-time dynamic expansion that can be predicted using codes based on non-ideal detonation theory.With decoupled charges in presplits for example, the pressure drop between the charge and the blasthole wall can be simply described to first order using the energy relationship associated with adiabatic expansion. However, a more realistic mechanistic solution involves interacting fluids and turbulence leading to dynamic processes such as the channel effect.CITATION:Minchinton, A, 2015. On the influence of fundamental detonics on blasting practice, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 41–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By H J. Ross, R K. Beatson, T J, W R. Fright

Traditional method of explicitly defining three-dimensional (3D) ore-waste and geological boundaries relies heavily on a time-consuming process of manual digitisation. This method of modelling can be best described as surface modelling, as complex surface geometry is built up by digitising points that lie on the surface. With the advent of fast 3D interpolation methods, however, construction of geological surfaces using volume functions is now a practical alternative to explicit modelling of surfaces. Unlike explicit modelling, surfaces contained in volume functions are not explicitly defined or digitised. Instead the existence of surfaces in the volume function is implicit, thus the process of modelling surfaces from volume function is called æimplicit modellingÆ. Based on recent advances in fast scattered data interpolation methods, implicit modelling first defines a continuous three-dimensional function that describes the grade or rock distribution. This volumetric function is interrogated for a grade value, or a geological surface, thus allowing the extraction of the 3D object to be automated and eliminating the need to manually digitise surfaces. Since the function is continuous throughout space and does not depend on a mesh or grid for its definition, the extracted geological or grade wireframes can be constructed at any desired resolution in the specific volume of interest. The volume modelling method can work on scattered drillhole data of any data density, including processing combined information from dense grade control data as well as sparse resource drilling. It offers distinct advantages over surface modelling, including: being able to wireframe geological objects that may take days to digitise in tens of minutes; substantial improvement in modelling accuracy; and the ability to generate conditional models rapidly allowing mining risks inherent in geological modelling to be examined.

Jan 1, 2003

By S T. L Harrison, J-P Franzidis, M Becker, N Dyantyi, J L. Broadhurst

Gold mining is a major contributor to the South African economy, but is associated with several environmental issues such as acid rock drainage (ARD). ARD is due to the oxidation of sulfides in gold tailings and is characterised by low pH, high sulfate content and elevated concentrations of heavy metals that contaminates scarce water resources and subsequently limits the use of such waters without treatment. Treatment strategies can only be implemented if the acid-generating potential of mine wastes is effectively predicted using common static and kinetic acid prediction tests. The choice of test performed is usually a trade-off between the number of samples, speed of the test, cost of the analysis and level of information obtained. Often the results of these various tests are not consistent with one another. This study uses mineralogy to analyse biokinetic test results of a Witwatersrand gold sample in order to improve the understanding of behaviour of mine wastes under different ARD prediction test conditions.All ARD prediction testing methods investigated in this study showed that the gold sample is considered to be potentially acid forming with net acid generation (NAG) pH of 2.5 and net acid producing potential (NAPP) of 36 kg H2SO4/t. Results of biokinetic test showed that ANC was consumed within four days confirming acid producing potential of the sample with low neutralising potential as observed from acid base accounting (ABA) (4.7 kg H2SO4/t) and mineralogy (4.9 kg H2SO4/t). Results generated in this study demonstrated importance of mineralogy in both understanding the controlling reaction mechanisms playing key role in ARD formation and its capability as a prediction technique. Future work will focus on the application of mineralogy in interpreting the behaviour of mine waste under different static test conditions with a view to assessing their applicability and reliability in estimating potential acid generating characteristics of gold tailings.CITATION:Dyantyi, N, Becker, M, Broadhurst, J L, Harrison, S T L and Franzidis, J-P, 2013. Use of mineralogy to interpret laboratory-scale acid rock drainage prediction tests - a gold case study, in Proceedings World Gold 2013, pp 519-526 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By B Taylor, S Evans

Bulk explosive technology for underground mining has not seen any significant technological advances since the widespread transition from ammonium nitrate fuel oil (ANFO) to ammonium nitrate emulsions (ANE) commencing in the 1980s. The in-hole energy profile that conventional ANE systems deliver is limited by the physics of chemical gassing and simple control systems. This compromises the range, precision, and accuracy of energy delivery into the blasthole, and in some cases limits the length of charge that can be delivered. Orica’s 4D™ bulk system removes many of these constraints, enabling better blasting performance across all underground mining methods. This paper reviews work completed at three mining operations across Australia, the United States, and Chile with a focus on how this system can improve mining operations and deliver sustained commercial and productivity benefits into the future. These benefits include improved ore recovery, reduced dilution from waste rock, and reduced overall explosives consumption. This paper also reviews how this new technology can be applied for planning future mining operations.

Sep 1, 2024

By O Joneydi, J Viljoen, R Funnell

Computational Fluid Dynamics (CFD) modelling is a useful tool that can assist engineers in designing effective ventilation systems for the control of airborne dust generated during mining operations. Thistechnology can save time, effort and the costs associated with re-work or the traditional on-site experimental field trials by running desktop 3D simulations of the various proposed scenarios using state-of-the-art CFD analysis tools. Before implementing a dust management system, an understanding of the behaviour of airborne dust particles in the face zone can be achieved, which can improve the confidence in the secondary ventilation and dust management design. Usingadvanced numerical models, suitable dust extraction strategies can be foreseen, and multiple scenarios can be simulated and investigated quickly. As a case study, dry drilling operations in Kimberlite orebodies produce large quantities of fine dust which poses health and safety risks. An effective dust management system is required to achieve acceptable face conditions. A possible practical solution is a ducted exhaust ventilation system with a force fan in the face zone. This paper demonstrates how CFD analysis can be used as a tool to assist the design engineer with validating and optimising the proposed ventilation design by tracking the trajectories of different size dust particles, to determine the best equipment layout and appropriate flow rates which minimises airborne dust.

Oct 12, 2022

Prior to 1972, Peko Mines Limited at Tennant Creek used a central mill at Peko, which consisted of a gravity circuit, flotation and cyanidation of tailings, to treat their gold ore from surrounding mines. The Warrego concentrator, 60km to the west, was built to handle the Warrego and Gecko copper orebodies, which were being developed concurrently with the concentrator construction The Warrego concentrator consisted of a flotation circuit, using autogenous grinding at 100 - 120 tph, compared to the more elaborate Peko circuit employing rod mill - ball mill grinding capable of treating only 18 - 26 tph. During development of the Warrego copper mine a gold rich ore pod was located, because of which the mining plans were adjusted to allow simultaneous, separate extraction of the copper and gold ores. However, the plans for the concentrator were not affected as the gold ore could be carted 60km to the Peko central mill for processing.

Jan 1, 1978

By S G. Hagemann, M E. Barley

The Mt Tom Price deposit is a world-class high-grade hematite deposit in the Hamersley Province of Western Australia with an original resource of 900 Mt of almost pure hematite, averaging 63.9 wt per cent Fe. Petrological and geochemical studies at both the Southern Ridge and the North deposit at Mt Tom Price have identified three hypogene alteration zones between unmineralised BIF and high-grade iron ore: distal magnetite-siderite-stilpnomelane; intermediate hematite-magnetite-ankerite-talc-chlorite; and proximal martite-microplaty hematite-magnetite-apatite alteration zones.Fluid inclusions trapped in siderite within the distal magnetite-siderite- stilpnomelane alteration zone at the North deposit revealed primary high salinity (25.5 eq wt per cent NaCl-CaCl2) inclusions that homogenised between 107¦ and 142¦C into liquid. Fluid inclusions trapped in ankerite within ankerite-microplaty hematite veins in the intermediate hematite-ankerite-magnetite-talc-chlorite alteration zone at the North deposit revealed mostly H2O-CaCl2 pseudosecondary and secondary inclusions with salinities of 22.4 - 25.4 eq wt per cent and 22.9 - 25.9 eq wt per cent CaCl2, respectively. Pseudosecondary inclusions homogenised between 153¦ and 449¦C and secondary inclusions homogenised between 103¦ and 157¦C. Fluid inclusions trapped in apatite within talc-microplaty hematite veins in the intermediate hematite-magnetite-talc-chlorite-apatite alteration zone at Southern Ridge revealed that primary, medium salinity (7.0 - 9.0 eq wt per cent NaCl) inclusions homogenised between 181¦ and 257¦C and primary high salinity (22.8 - 25.9 eq wt per cent CaCl2) fluid inclusions homogenised between 118¦ and 257¦C into liquid. Microthermometric analysis of quartz from quartz-hematite veins from the Southern Batter Fault, Southern Ridge show a complex fluid inclusion history. Primary fluid inclusions consist of: low- and high-salinity H2O-NaCI inclusions trapped at temperatures of approximately 140¦ to 230¦C; vapour-rich inclusions of unknown compositions; and æcomplexÆ salt-rich (Ca, Mg, K and Na inclusions).Secondary inclusions consist of medium-salinity fluid inclusions trapped at temperatures of about 140¦ to 280¦C.A two-stage hydrothermal model is proposed for the formation of both the Southern Ridge and North deposits. Early 1a hypogene alteration involved the release of hydrothermal NaCl-CaCl2-rich (25.5 eq wt per cent) basinal brines (110¦ - 150¦C) from the underlying Wittenoom Formation and directed upward along normal faults and focused within the silica-rich rocks of the Dales Gorge Member, by the shales of the underlying Mt McRae Shale Member and overlying Whaleback Formation. Within the Dales Gorge Member hydrothermal basinal brines migrated laterally within large-scale folds with permeability controlled by shale bands and the NW trending dolerite dyke sets. Fluid rock reactions transformed unmineralised BIF to magnetite-siderite-iron silicate BIF, with subsequent desilification of the chert bands. Stage 1b hypogene involved an increase in temperature of the hydrothermal, CaCl2-rich saline (24 eq wt per cent) basinal brines (250¦ - 300¦C) resulting in formation of hematite-ankerite-magnetite-talc-chlorite alteration and the crystallisation of microplaty hematite. Late stage 1c hypogene alteration involved the interaction of low-temperature (~120¦C) basinal brines with the hematite-ankerite-magnetite mineral assemblage. At the Southern Ridge deposit this process was very intense (ie high fluid flux), therefore resulting in the almost total removal of ankerite and resulting in the increased porosity of the ore. Stage 2 supergene enrichment in the Tertiary resulted in the removal of residual ankerite and apatite and the weathering of the shale bands to clay.

Jan 1, 2005

By Morrell S

As more and more autogenous and semi-autogenous mills are run in closed circuit with cyclones the limitations that can be imposed by poor grate and pulp lifter design are becoming increasingly apparent. Relevant literature on the subject is al

Jan 1, 1997

At Cliffs Natural Resources Ltd (CNR) crushing and shipping sample stations, precisions are estimated for the sampling, preparation and measurement stages of iron ore sampling in accordance with ISO 3085 (2002). In this Standard, gross duplicate samples are prepared at each of the three stages, yielding eight measurement assays. Appropriate calculations of the differences between assay pairs are then made to estimate precision of each stage of sampling. The International Standard for checking precision in iron ore sampling, ISO 3085 (2002) prescribes a method for identifying outliers that is ambiguous and possibly inappropriate. The procedure also makes an unnecessary implicit assumption, that the differences between assay pairs are normally distributed. The Anderson-Darling statistic is used to demonstrate that in some cases the assay pair differences have distributions significantly different from normal. When applied at CNR as specified, the Standard leads to precision estimates well below the expected values, thus overestimating the sampling method's capability and limiting the opportunity for real process improvement. This paper suggests an improved method of estimating sampling, preparation and measurement precision. A bootstrap procedure is used to estimate confidence limits for the calculated precision estimates. The proposed method would be suitable for testing blasthole precision. The discussion is supported by extensive simulation modelling of realistic data.

Mar 1, 2010

By S McGregor, J Sharp, I Entezari, T Boulter

The piezocone penetration test (CPTu) is one of the primary screening tools used by the mining industry to evaluate whether tailings are susceptible to liquefaction (static or cyclic). Liquefaction analysis using the CPTu is influenced by the fines content of the soil, and most CPT screening tools empirically use the behaviour type index (Ic) to correct for fines. The issue with this approach is that such empirical relationships have been developed using data collected from natural soils and their applicability to different tailings deposits needs to be studied. In this paper, we explore the use of machine learning to develop a site-specific model to estimate fines content of tailings using gamma piezocone penetration testing (GCPTu) measurements. The results are then compared to the fines content derived from the soil behavior type index (Ic) proposed by Robertson and Wride (1998). A dataset of paired GCPTu and laboratory results were compiled and a support vector machine (SVM) algorithm was employed to calibrate a model to estimate tailings fines content from in-situ GCPTu data. We calibrated GCPTu data to geotechnical 75 μm fines content measured in the laboratory. The geotechnical fines content is the fines content as a percentage of solids. The development dataset was comprised of paired GCPTu-laboratory results collected in 2009-2019 from a mining area with predominately clay mineral and quartz sand tailings. Results show that the developed model predicts the geotechnical 75 μm fines content of the studied deposits with 7.8% error. The Ic based method estimates the fines content with 31% error. Evidently, the Ic method is not applicable to the studied tailings deposits. It is appreciated that many tailings fines do not contain clay, and that the success on this program may not be repeatable everywhere. However, the authors wish to point out that the application of site-specific machine learning algorithms may be used to significantly improve empirical geotechnical parameters.

Jul 1, 2021

Bendigo Mining operates a 600 000 t/a comminution, gravity, flotation and leaching processing plant for the recovery of gold from their Kangaroo Flat Operation, in the Bendigo goldfields. The free gold and gold bearing sulfi des present are typically coarse grained and hence are highly amenable to gravity recovery. Plant operating data is consistently showing that over 78 per cent of the feed gold is recovered in a circuit, consisting of inline pressure jigs, inline spinners followed by free gold tabling and intensive leaching of tabling tails. The circuit receives coarse crushed product from high pressure grinding rolls and the grinding mill discharge, which allows material to be re-circulated through the gravity process until the particles are small enough to enter the flotation circuit. A plant audit was completed on 26 November 2009 designed to give an indication of the overall operational characteristics of the gravity circuit including single pass efficiencies of associated equipment. The techniques, results and challenges of such a survey are discussed.

Aug 1, 2010

By P Mikula, R Geranmayeh, R Carlton, M Ferguson, R Whiting

The concept of using specially designed slot blasts to mine through stress abutments that intersect faults, while controlling fault-slip seismicity, has come of age at Mt Charlotte Mine. Due to the high and adverse stress field and the presence of major faults, the mine is vulnerable to significant fault-slip seismicity. As mining proceeded, advancing stress abutments around various mined areas encroached on several major subvertical faults. If the sequence formed a diminishing pillar between stope and fault, the removal or failure of that pillar daylighted the fault, and often resulted in significant fault-slip seismicity. A new strategy called ‘Tight Slot Blasting’ (TSB) was developed to restrain or dampen this style of fault-slip movement. The TSB has geometric similarities to a conventional cut-off slot used to create stress shadows, but its function is different. Its objective is to trigger and control a sudden shift of the stress state on a fault from an initial stable state, through an unstable transition, to a second stable state. A TSB firing advances a long tall narrow slot through a stressed abutment between a stope void and a nearby fault, using a rapid blast with a low swell ratio, so that the slot substantially and rapidly fills with blasted rock fragments. During the blast process, the stressed rock is rapidly removed and transformed into the fragmented rock fill in the slot. The strategy deliberately allows a fault-slip episode to manifest at a chosen time and place. The tight-packed broken rock in the slot performs an essential shock-absorbing function by controlling the slip amount and rate on the fault, while at the same time the fill becomes compacted by the movement. This controls the dissipation of fault-slip energy, and greatly reduces the seismic response in time and space. A small closure across the slot occurs, with consequent relaxation and destressing of the adjacent rock mass. Stress monitoring data shows that slot creation lowers the abutment stress in the nearby rock mass, while the newly placed fragmented rock fill acts as a shock absorber, providing considerable resistance to substantial fault-slip movement that otherwise could deliver a significant seismic event. First used in 2007, the strategy has been refined to become a routine specialised practice for management of seismically hazardous situations at Mt Charlotte, with 12 successful TSBs conducted to date. Despite mining through multiple high stress abutments, seismic reactions have not exceeded ML 2.1 with any TSB firing, all remaining below the site tolerable maximum of ML 2.3. This paper presents an overview of the strategy, and five case examples of the strategy in critical stressed areas in July 2016, Sept 2017, Dec 2017 and two in Oct 2020. The strategy has successfully managed the seismicity and is expected to remain an essential part of the seismic management plan at Mt Charlotte Mine.

Nov 29, 2022

By M Colwell

The Coal Mine Roof Rating (CMRR) is a rock (roof) mass classification (RMC) system/index that was originally developed by the United States Bureau of Mines (USBM) for aspects of underground coalmine geotechnical design and was first introduced to Australia as a part of the original Analysis of Longwall Tailgate Serviceability (ALTS) project conducted in 1997/1998. In subsequent years further refinement to its calculation was undertaken, such that the CMRR is now an industry standard for quantifying the structural competence of the primary bolted roadway roof interval and has been routinely/widely used by Australian collieries over the last 25 years with great success for roof support/chain pillar design. There have been many publications discussing the use and calculation of RMC systems and this paper also provides an important update and recommendations in how best to calculate the CMRR. However, it is rare to find an explanation as to why and how a RMC system/index satisfactorily takes account of the mechanics and rock mass behavioural issues associated with ground reinforcement. This paper provides such an explanation and insight with respect to the CMRR so it is: 1) better understood, 2) to allay any concerns, and therefore 3) will continue to be confidently used by and for the collieries’ benefit.

Nov 29, 2022

By M J. Newton

As part of the AMIRA P843 project Keeney and Walters (2008) describe how the principal components analysis (PCA) method can be used to identify classes of samples with similar metallurgical characteristics. However PCA does not take account of the location of each sample in 3D space. This paper describes a study to analyse the spatial distributions of the classes and determine appropriate modelling methods to control the estimation of the comminution parameters and mill performance indices into a 3D block model. This includes but is not restricted to geostatistical techniques that are used for grade modelling. The starting point for the study is the class definitions and the regression models for estimating the comminution parameters and performance indices. Each sample is assigned a class and the spatial distribution of each class has been analysed using different techniques including the calculation of variograms. This establishes whether the classes can be used as domain control for estimation into the block model – a procedure similar to using geological rock type domains for controlling the estimation of grades for a resource model. However, standard geostatistical estimation methods such as ordinary kriging assume that the variable being estimated is additive or linear. This assumption is valid for variables such as grade but this is not necessarily the case for the comminution parameters or the performance indices. Therefore the estimation procedure must either use variables that are definitely additive or the effect of potential non-additivity must be tested and accounted for where possible.The results of the study show how performance indices such as recovery, throughput and specific power can be estimated into the block model. This model is then combined with the geological model to provide a multi-parametric model that is used to optimise the mine planning and scheduling activities which can lead to significant improvements in NPV.

Sep 5, 2011

By B Flynn, P Knights

Low-loaders or 'floats' for relocating equipment in surface mines are limited to a capacity of approximately 350 t. In the iron ore industry it is desirable to be able to rapidly relocate excavators in order to maintain production rates within appropriate quality limits. In addition, the ability to rapidly relocate heavy equipment raises the possibility of improving the quality of repairs by performing maintenance in controlled shop conditions. However, many iron ore operations operate hydraulic excavators in the 600 to 800 t range, with newly released excavator models exceeding 800 t. These excavators are too large to float using conventional technology. This paper examines the potential for using multi-bogie transporters to relocate large hydraulic excavators in surface mines. Recent innovations have seen the development of modular transporters which can be coupled together to achieve larger platform areas. When separated, and with their drive bogies neutralised, these units are able to be towed behind prime movers and relocated between mines via public roads. The potential cost savings for relocating a Terex RH170 excavator in an open pit coal mine are examined. In the first six months of 2008, the analysis showed the potential for a 38 per cent reduction in total travel time with a corresponding revenue increase of approximately $350 k. The paper recommends that a feasibility study be conducted into offering a heavy equipment relocation service within the Pilbara region.

Jan 1, 2009

By R F. G Phelps

The former Gwynfynydd gold mine is located within the heart of the Snowdonia National Park, North Wales, United Kingdom. The black shale-hosted quartz reefs have intermittently produced more than 50 000 ounces of gold since 1863. Its most recent period of operation by Welsh Gold PLC was between 1992 and 1999 when it extracted 10 000 tonnes annually from a total resource base of 180 000 tonnes. A historical mining grade of 15 grammes/tonne was recovered from the Chidlaw Reef on which all production was based. Erratically distributed gold pockets hosted in the footwall zone of a 3 - 6 m wide quartz reef characterise the mineralisation. The gold exhibits a high-nugget effect and as a consequence the accurate determination of tonnage and grade was difficult. Production was undertaken by overhand shrinkage stoping. Due to its location within a National Park certain environmental constraints were placed on the operators. The principal requirement of planning permission was that processing should take place above ground and not involve chemicals. As a result, an underground mill based on physical separation methods was constructed in response to these environmental constraints. Much of the mine discharge is related to the flow of rainwater through the workings from surface openings on the reefs. Discharge from the underground milling facility was enhanced in various metals, particularly zinc, though was reduced to legally acceptable levels using liming tanks prior to discharge into the River Mawddach. The company was required to monitor and treat all water discharged from the mine before it reached the river. The mine closed in 1999, since which time a tip re-processing has continued as part of an environmental remediation and gold supply program.

Jan 1, 2002

By G J. Harbort, K Lam, C Sola

The relationship between the geology of porphyry copper deposits and their processing performance is an area of interest. Being able to predict comminution properties of the ore from physical characteristics and geological descriptions would allow an increase in the precision of capital cost estimates, operating cost estimates and throughput rates. This geometallurgical approach would reduce the requirements for expensive comminution tests.As the comminution circuit is the highest capital cost item in the plant and a possible throughput bottleneck, understanding the variability in hardness within the orebody is critical. A geometallurgical model allows calculation of ore hardness values in mining blocks from ore characterisation data. This model subsequently uses a combination of simulation and power-based approaches to relate ore hardness and flotation feed size to grinding circuit throughput.This paper reviews the geometallurgical models developed for seven porphyry copper deposits and discusses the strengths and shortfalls of the methodology and similarities and differences between the different deposits.CITATION:Harbort, G J, Lam, K and Sola, C, 2013. The use of geometallurgy to estimate comminution parameters within porphyry copper deposits, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 217-230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013