Search Documents

By M Korte, J McMaster, C Brent

The Barrick Osborne concentrator has gone through a number of upgrades since commissioning and has increased production from the original 119 t/h design capacity to a milling throughput of 265 t/h in 2008. This was achieved incrementally over several years, by maximising operating efficiencies, in order to minimise capital expenditure, and take advantages of economies of scale; but more importantly it was reached with no measurable loss of recovery. Osborne currently processes a blend of underground and open pit material from the nearby Trekelano deposit. Following primary/secondary crushing, the material is processed through a rod/ball mill grinding circuit ahead of rougher/scavenger flotation that produces a copper concentrate. Osborne was seeking a further increase in plant throughput of the order of 15 per cent, but at more sustainable levels of secondary crusher plant utilisation. In early 2008, Osborne contracted Metso Process Technology and Innovation (PTI) to review the entire process from run-of-mine feed to final copper concentrate. This review would be done concurrently with surveys of both the crushing/grinding and flotation circuits being performed at the same time. The outcome would be a steady-state model of the complete flow sheet allowing the crushing/grinding model to interact with the flotation circuit model, such that overall process optimisation was possible. This was to apply both by exploring the operating limits of the currently installed plant, as well as looking at the logical next stage of capital plant expansions. Surveys of the crushing and grinding circuits were conducted at the Osborne concentrator in May 2008. The main objective of the surveys was to review the potential of increasing grinding throughput whilst maintaining the flotation feed 80 per cent passing size. This would also require improving the efficiency of the crushing circuit which was already operating in excess of 80 per cent of the time. Steady-state simulations were performed using the developed circuit models to identify opportunities to increase throughput and alleviate high circulating loads in both the secondary crushing and grinding circuits. Due to operational changes, the recommendations resulting from this project were considered by Osborne but have as yet only been partially implemented.  This paper covers part A or the crushing and grinding component of the project. A separate paper discussing part B or flotation is also being presented at this conference. The results of interactive simulations between the flotation and grinding circuit models are included in part B of this paper.

Jan 1, 2009

For a large scale open pit mining and concentrating operation, on a low-grade disseminated ore body, it is possible to set an approximate lower bound on economically feasible operating scales and an approximate upper bound on economically desirable scales in a relatively straight forward manner. The optimum scale ofplanned operations, with respect to the objective ofmaximisation ofthe net value ofthe orebody, will have to be arrived at by iterative planning runs, but it may be expected to lie close to this upper bound. The effects of infrastructural costs and of the addition of a risk premium to the cost of capital, to form the discount rate for planning purposes, are considered theoretically and by worked example. It is concluded that a perceived special, unsystematic, risk should not be accounted for by the use of such a risk premium as this is inducive to placing a greater amount of investment capital at risk, for no greater return-rate to investment.

Jan 1, 1986

By Lynch A. J

A method has been developed for the prediction of the performance of multi-stage grinding-cyclone classification circuits of any degree of complexity on any ore for a wide range of operating conditions. The method involves the simulation of the circuit on a digital computer by means of. mathematical models of the individual units. At present, to establish the characteristics of the ore and the machines in mathematical terms, it is necessary to know the performance of a simple system on the ore for one known feed rate and feed sizing analysis.Further work on the separate identification of the terms defining the characteristics of the ore and the machines may permit the method to be applied directly to the data derived from small scale tests on ores.INTRODUCTIONThe cost of preparing metalliferous ores for concentration processes by, grinding and classification frequently represents a major portion of the cost of treating such ores, and it is necessary both from an economic and a metallurgical point of view that grinding and classification circuits should be operated at their optimum efficiency. It will be realized that the processes carried out in all units in such circuits behave according to physical laws and, if a mathematical representation of the laws applying to each unit could be derived, optimization of the overall process for any given conditions of feed or product may not be difficult.The physical processes in both tumbling mills and hydraulic classifiers are extremely complex and do not appear at present to be amenable to a rigorous mathematical analysis. However, empirical mathematical models of grinding units which have been presented previously (Callcottand Lynch, 1963; Lynch and Moore, 1963) may be used to discuss the operation of the grinding units in multi-stage circuits. Another type of model, which leads to a reasonable...

Jan 1, 1965

In a previous paper the writer dealt -with the jasper bar formations and their relationship to the structural geology of older pre-Cambrian rocks in the goldfields districts of Western Australia (24). He has pointed out in this ahd other papers that jasper bars, or banded iron formations, banded hematite or ,magnetite quartzites, jaspilites and related banded ferruginous or non-ferruginous cherts, occur in abundan'ce in the Older Greenstone Series of Western Australia (22), (24), (26). They are considered to represent special forms of banded ferruginous sediments, and are usually fpund in the field interbedded with more or less metamorphosed pasaltic 01' andesitic lavas and tuffs, now amphibolites, together with occasional thin bands of normal pelitic sediments, which go to make up a large proportion of the Older Greenstones in thfs State (26).Great thicknesses of fiat-bedded ]:landed ferruginous cherts are also found associated with cherty' carbonate rocks; quartzites, shales and thin-bedded dolomite whicIi constit'ute the Nullagine (Pl'oterozoic) system in the northwest of Western Australia. In the Hamersley Range district these banded ferruginous chert beds are the hosts of important deposits of blue amphibole asbestos.In the paper mentioned above brief reference was> made to the importance, of geological structure in relation to economic geology, particularly in the goldfields regions of Western Australia, and it was shown that jasper bars may have an important role in the study of 'the structural geology of many of these regions. Of possibly more immediate economic importance is the part that these rocks play, both directly and indirectly, as host rocks for mineral deposits-the chief of Which are gold, iron ores, blue asbestos, and manganese ores. The blue asbestos bearing banded iron formations mentioned above are confined to the younger pre-Cambrian Nullagine formations. They have been described in detail elsewhere (23). In this paper it is proposed to discuss the economic geology of the jasper bars found in the older pre-Cambrian series.The jasper 'bars have in themselves little or no intrinsic value except perhaps some of the more highly coloured and banded varieties which may be utilised for ornamental and decorative purposes. Probably the best known of such varieties is the so-called "marble bar;" a belt of, strikingly coloured banded chert occurring just south and west of the famous town of that name (see Fig. 1t). This consists of a hard, very fine, even-grained rock with alternate individual stripes varying from the thickness of a sheet of paper up to an inch or more in width, and ranging in colour from clear white to yellow, from various shades of pink to brilliant...

Jan 1, 1943

By R J. Goldfarb

Reduced intrusion-related gold deposits have become a new, low-grade, large-tonnage exploration target during the last decade. The best recognized examples of such deposits are recognized throughout the Tintina Gold Province of the northern North American Cordillera. Because such examples may have many features in common with orogenic gold deposits, such as anomalous Bi, W and Te, low salinity and CO2-rich ore fluids, and a spatial/temporal association with igneous rocks, confusion and controversy have now become commonplace in classification of many gold deposits formed along convergent margins. The best discriminators of IRGS are likely to be their: +        regional location in deformed shelf sequences on the inboard side of a series of accreted terranes and within terranes that also contain important tin and (or) tungsten deposits; +        local spatial association of gold ores with cupolas and contact aureoles of relatively reduced, alkaline-leaning, and volatile-rich plutons; +        post-deformational timing of gold deposition; +        extremely low sulfide content (commonly <1 vol %) of ores within igneous bodies and the outward zoning, through proximal skarns and to distal base metal-rich veins, from the causative pluton; and +        low grades (<1 g/t Au) of auriferous sheeted vein systems in pluton cupolas.

Jan 1, 2005

MR. W. E. WAINWRIGHT occupied the chair, and in introducing the lecturer said, on account of the absence of the vice-president, it fell to his lot to introduce the lecturer. Mr. Tennberg, he said, was visiting Australia, and those present might wonder who he was.He understood that the lecturer w~s a reputable practising geophysicist, associated with a reputable company! It was rather desirable perhaps to say that the Institute had made some inquiries with regard to his status. Geophysics was a comparatively newscience, and had suffered several hard knocks in Australia and elsewhere. Most of those knocks had been the result of undue optimism of a number of people who did not understand what they were talking about. It had been claimed that geophysics was a...

Jan 1, 1930

By Prasad S, Chatterjee S. S, Singh B. N

The chief source of metallic iron for steelmaking in India, even today, as it is in most part of the world, is through blast furnace (BF) route. This will continue to be so in the foreseeable future as the technology is most efficient, both process and economy-wise. However, as the world is moving into the next millennium, a critical look is being given to the process primarily because of its non-ecofriendliness (as a result of extensive use of metallurgical coal/coke requiring elaborate pollution control facilities) and huge investment involved for supporting facilities like extensive raw material preparation and handling, agglomeration, adoption of sophisticated instrumentation and control system, etc.

Jan 1, 1999

By X-F Zhao, J-W Li, L-P Zeng

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The formation of Kiruna-type deposits has been ascribed to either immiscible iron phosphate melt separated from silicic magma or precipitation from magmatic-hydrothermal fluids. The early Cretaceous Ningwu volcanic basin in Eastern China contains tens of Kiruna-type iron deposits. The orebodies are mainly hosted within the top zones of subvolcanic dioritic intrusions and along the contacts between these intrusions and adjacent volcanic rocks/strata.The orebodies are commonly associated with widespread brecciation and wall rock replacement. Magnetite formation was closely associated with extensive hydrothermal alteration that may extend kilometres, with both vertical and horizontal zonation. Field and textural data indicate that magnetite formed slightly later than albitisation but coeval with apatite and actinolite. Elemental analysis of magnetite and apatite from ores shows distinct features to those as igneous accessary minerals in the host dioritic intrusions, suggesting a genetic relationship to magmatic-hydrothermal processes. Magnetites have elevated TiO2 (up to 5 wt per cent) and V2O3 (up to 0.7 wt per cent), which implies that they are derived from incipient high-temperature magmatic fluids. It is concluded that the Kiruna-type deposits in the Ningwu basin most likely formed from high-temperature magmatic-hydrothermal fluids. The emplacement of dioritic intrusions into a subvolcanic setting likely plays a critical role in the development of Kiruna-type deposits.CITATION:Zhao, X-F, Zeng, L-P and Li, J-W, 2015. Kiruna-type iron deposits in the Mesozoic Ningwu volcanic basin, Eastern China – origin and relationship to subvolcanic dioritic intrusions, in Proceedings PACRIM 2015 Congress, pp 657–662 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Hellsten KJ, Butt CRM

Major Francis Hamilton Buchanan coined the term `laterite' (Latin; brick-rock) in 1807 for the red earths used for building blocks in southern India. Although these earths were actually weathered basalts, the term is now applied to weathering profiles developed upon a wide range of bedrocks. The Ni-laterites are a special class within the broad laterite family.

Jan 1, 1996

THE art of mine surveying has made very great progress in recent years, and is still advancing, perhaps faster than any other branch of surveying. The scope of the mine surveyor's duties has greatly increased, his instruments and methods have improved, the responsibility of his position is greater, and the end is not yet in sight.It might be supposed that such a steadily growing subject would have an adequate literature, but this is by no means the case and outsiders commonly judge mine surveyors by their text-books. Hardly any condemnation can be too strong for most of these books. The English books truckle to the antiquated and crude methods apparently still in use in England, and thereby largely aid in perpetuating them; they commonly in illustrative examples give the distances in fathoms, feet, and inches; they spend page after page discoursing on instruments that should have been forgotten long ago; they try to antagonize theory and practice by detailing such calculations as that a certain vein will contain 2,003.907 pounds of galena per square fathom, and then reduce this amazing quantity to hundredweights, quarters, and pounds. Nothing can be more unscientific, or, for that matter, less businesslike, than unwarranted assumptions of accuracy; it is, perhaps, the greatest curse of applied science. Here we have a calculation to thethousandth part of a pound, when there is probably an unavoidable error of two hundred pounds. What shall we say of a man who explains how to measure the depths of shafts to the hundredth part of an inch by means of short brass rods screwed together...

Jan 1, 1909

The 8 ft by 91/2 ft drive which joined No. 7 Shaft with Browne Shaft on the 1,480 ft level was extended from both ends and met at a point approximately 12,000 ft from No. 7 (2,000 ft from Browne).The surveying required for this 2 1/2 mile haulage drive called for greater accuracy than was obtainable from South Mine standard methods. Procedures and devices from published information were tried and modified as required to suit local conditions. Several new methods were applied and improved as the drive advanced. The control of angular, linear and level measurements was perhaps considerably in excess of the requirements, but this was offset by abnormally large discrepancies resulting from shaft plumbing. The accuracy of the final breakthrough, although not to the standard desired, was sufficient to complete the connection without inconvenience and added cost.INTRODUCTIONThe acquisition of the Browne Shaft leases in January 1962 presented the management of Broken Hill South Limited with the problem of transporting ore from these leases to its mill. It was eventually decided that diesel locomotivehaulage through a 2t mile drive on the 1,480 ft level between the two mines was the best solution. The drive was advanced from both ends after Browne Shaft was deepened by 80 ft to reach the 1,480 ft level horizon. Each end advancedabout 15 ft/day with the miners working three 7 hr shifts. Blasting was restricted to the end of the shift.The survey work involved five shaft plumbings and 78 theodolite stations in a traverse, underground and surface,of more than 5 miles. Because of the exceptional length of the drive, an unusually high degree of reliability was required.The aim was for a maximum error at breakthrough of 1 ft 1 in 30,000, and to secure this, precise methods of linear measurement were necessary. Shaft plumbing in particular posed special difficulties.

Jan 1, 1965

The assistance that can be gained by the use of aerial photographs in the geological examination of a mineral field is clearly illustrated by the results of a rapid reconnaissance survey of the newly-discovered Mount Fitton talc, deposits, situated in the north-eastern extension of the Flinders Ranges in South Australia.The talc deposits were found to occur about the margins of a large lenticular mass of dolomitic marble, interbedded with hornfelsic tillites and fluvio-glacial sediments of Upper Pre-Cambrian age. Aerial photographs show clearly the extent of the dolomitic marble on which the growth of a species of eucalypt-Eucalyptus Gillei-is prominently developed, and which assists in defining the limits of this relatively light-coloured formation. (See Fig. 1).Upon field investigation it was found that the talc, deposits are related closely to the margin of the dolomitic marble where the latter has been subject to minor folding and faulting. The deposits themselves have been formed by metasomatic replacement of schistose dolomite. The contact of the dolomite with the underlying and overlying glacial beds is also noteworthy for the presence of minor occurrences of copper, silver, lead and zinc minerals.An examination of photographs covering a wide area reveals an outcrop of a massive granite to the north-east of the dolomitic marble, Fig. 2, which was almost certainly responsible for the regional metamorphism of the dolomitic and glacigene sediments, and the source of the mineralising solutions.All these features, as well as the broader structural features of the area, which are extremely important in the understanding of, individual commercial depQsits, were quickly determined with the assistance of the photographs.It is useful, briefly to relate the procedure adopted in examining this recently developed field as an example which may be well worth following on other fields, even if exposures are not so clearly defined. The method to be outlined, of course, will be of maximum advantage. Where rock exposures are good, where the ore bodies are likely to be widely spread, and where such bodies are related to some major geologi-cal control. Typical of such deposits are pegmatitic, hydrothermal and related ore bodies associated with the periphery of an igneous intrusion, or ore bodies related to particular sedimentary horizons in a regionally metamorphosed province.Procedure.The first requirement is the preparation of a detailed reconnaissance geological plan of as large segment as possible of the potentially mineralised province. The use of aerial photographs is par...

Jan 1, 1950

The paper outlines the development of a solvent extraction process for the recovery of scandium, yttrium, thorium, and heavy lanthanides from waste sulphate liquor at the Port Pirie uranium treatment plant. A summary is given of known solvents for these elements, including the recently developed alkyl-phosphoric acid esters which are applicable to sulphate solutions.A kerosene solution of di- (2'-ethylhexyl) phosphoric acid (EHPA) has been suggested by some workers as a suitable solvent for fractionation of the lanthanides. Experimental work with this solvent showed that it could be used for initial recovery of the above elements from low concentrations in the complex sulphate liquor. In particular, scandium could be recovered as a high grade product by extraction with 0·lM EHPA, followed by a purification strip with 9N sulphuric acid, and final stripping of scandium with sodium hydroxide solution.To enable alkaline stripping to be used successfully, the kerosene solution of the reagent was modified by the addition of a small proportion of nonanol. Experimental work included laboratory scale batch tests and small pilot scale continuous tests.A proposed extension of the process for the separate recovery of individual heavy lanthanides, yttrium, and thorium is described.INTRODUCTIONAt the Port Pirie uranium treatment plant of the South Australian Government, large volumes of "barren liquor", free from 'uranium, are at present run to waste. This "barren liquor" results from sulphuric acid leaching of Radium,Hill uranium concentrate, followed by separation of solid residues and removal of uranium from the clear solution by ion exchange. The mineral davidite, from which the uranium is derived, contains other potentially valuable components, notably vanadium, chromium, thorium, yttrium, scandium, and the lanthanides. These constituents are...

Jan 1, 1961

By M Dalm

More and more mining companies are becoming aware of the potential benefits of sensor-based ore sorting and process optimisation. This is reflected by a growing number of analysers that are available for drill hole logging, conveyor belt scanning, ore sorting, slurry analysis, etc. These tools all rely on a specific sensor technology that can be used to detect a material property such as colour, density, mineralogy, or chemical elements. However, all sensors have restrictions on the minerals and/or elements that can be detected or inferred. This is caused by the physical mechanisms behind the technology and depends on mineral concentration and compositional heterogeneity of the ore. Since nearly every ore deposit is unique in composition and characterised by different geological features that drive heterogeneity, no one-size-fits-all sensor solution is available. This makes it difficult for mining professionals to find suitable sensing technologies that can help them solve problems and improve processes for their specific ore types.

Sep 1, 2024

An extensive series of tests was carried out on a ball mill-rake classifier circuit in the New Broken Hill Consolidated Ltd. concentrator. The data were used to develop a mathematical model of the operation of a rake classifier and this model has been used in the simulation of the performance of a ball mill-rake classifier circuit on a digital computer. As a result of this simulation it has been possible to develop a technique for the optimization and control of a circuit which includes these units.

Jan 1, 1967

THE following short paper on the Blair Athol coal-field will no doubt have a twofold interest to members from the fact that its main seam, known as the "Big Seam" of a maximum thickness of 91 ft without a band, is unique, being probably the thickestseam of high-grade clean coal yet known, and also because of the interesting problem it presents the colliery engineer-viz., which system of mining is the best to secure the highest economical extraction.Location - Blair Athol is a mining township in Central Queensland, situated at an altitude of about 1100 ft. above sea-level at the end of a branch railway line 74, miles from Emerald, on the Main Central Western line, and 240 miles by rail from Rockhampton.Geology - The coal-measures appear to lie in a shallow basin of about four or five square miles in area, surrounded on all sides by slates and schists, which are overlaid oh three sides by alluvial deposits of up to 150 ft. in thickness, and on the fourth by a thick basalt bed, as yet unproved, some miles beyond which the auriferous slates outcrop. These alluvial deposits have been largely worked in years past and gave high gold returns, the chief diggings being Clermont and Macdonald's Flats in the south, the Springs and Black Ridge in the north-east, and Yankee Creek and others on the west. The surface of the coal-fields may be described as unbroken, but undulating, with gentle southerly dip, the watercourses opening out into wide flats. The absence of creeks or deep gullies accounts for no outcrops being visible on the surface, and the coal-measures...

Jan 1, 1918

Major Francis Hamilton Buchanan coined the term `laterite' (Latin; brick-rock) in 1807 for the red earths used for building blocks in southern India. Although these earths were actually weathered basalts, the term is now applied to weathering profiles developed upon a wide range of bedrocks. The Ni-laterites are a special class within the broad laterite family.

Jan 1, 1996

By F M. Weir, M Fowler

A discrete fracture network (DFN) approach involves numerical modelling that explicitly represents how defects may be spatially distributed through a rock mass. A DFN is a 3D realisation of the ‘smaller scale’, non-deterministic defects; it is not an attempt to model larger, deterministic structures that should be identified as part of an engineering geology model. The approach utilises structural data in stochastic analyses to give a range of possible models that provides a tool for visualisation and analysis of a rock mass and indicates the potential large-scale slope or tunnel performance and stability.Stochastic fracture modelling for rock mass characterisation has significantly advanced over the past 25 years. With recent improvements to field data collection and computational power, it has become recognised internationally as a valuable tool for modelling some geomechanical problems encountered when designing excavations in fractured rock masses.This paper provides an introduction to the DFN approach, particularly the necessary input parameters and derivation of these from typical structural data sources, such as boreholes or scan line mapping. Of particular importance for engineering applications is validation of the simulated fracture network and techniques for doing so are discussed here.CITATION:Weir, F M and Fowler, M, 2014. An introduction to discrete fracture network modelling and its geotechnical applications, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 435–444 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Mwaba CC

Ok Tedi Mining Ltd has been using flotation for the production of copper/gold concentrates from a complex copper sulphide ore for several years. During this period, much effort has been devoted to metall- urgical treatment of the ore. This paper examines some of the mineralogical aspects of the sulphide minerals in the ore using the electron microprobe analyser. Results have revealed the complexity of the copper sulphide minerals and in particular, chalcocite. Analysis of both plant and laboratory flotation products has provided further insight into the effects of mineralogy on the flotation of copper and iron sulphides. A significant observation is that some of the pyrite minerals apparently exhibit natural floatability. The implications of the mineralogical characteristics of the sulphide minerals on the flotation of the ore are also discussed.

Jan 1, 1991

Whether you are an employee, contractor or consultant working in the mineral industry, there are pressures to deliver the best possible performance. Technical professionals are usually driven by an internal desire to perform to a high standard because of personal pride in their profession, but there are an increasing number of external requirements to demonstrate that the actions taken were based upon reasonable grounds and that the work conformed to current best practice. People expect these best practice procedures to be followed and governments are now requiring those tendering for contracts to be registered in some way and to be participants in quality assurance schemes. One is not immune to these pressures just because you are working in a less legislatively sophisticated developing country in the circum-Pacific rim (pacrim) region.   Among the external pressures are the general ethical requirements of the professional body to which the person usually belongs, e.g. The Australasian Institute of Mining and Metallurgy (AusIMM), which are further elaborated upon in various Codes and Guidelines on specific matters, e.g. JORC (ore reserves reports) and VALMIN (assessment and valuation reports). These are outlined and discussed. Also, AusIMM's Chartered Practicing Status (CPS) Proposal is outlined in the context of other Pacrim countries approach to registering of technical professionals, which is a way of ensuring that minimum standards of qualifications, experience, competence and repute are demonstrable to ones employer (or client), peers and the wider community, including government.   Today, in the external working scene, there are many laws (particularly those applicable to the corporate and environmental spheres), with which contractors/consultants and even employees must fully comply, or else face criminal sanctions involving huge fines and imprisonment. These, too, are outlined and discussed. One must be able to mount a due diligence defence to avoid or mitigate these consequences.   Personal liability in the context of the day-to-day performance of one's duties has thus become a major concern to the technical professional and the ways in which it can be ameliorated, or insured against, are described. However, for some mineral industry practitioners, the problem is exacerbated because. of their general ignorance of the extent of their personal liability exposure. This paper intends to address this ignorance and to heighten general awareness of personal liability issues, as well as proposing some simple ways to limit this liability.

Jan 1, 1995